Sea Gull Lighting 59216LE-782 Installation Guide
Contents
1. ATED FOR AT LEAST 90 C TAB C MOUNTING HOLE lt CENTER COVER B FIGURE 1 sea gull lighting Installation And Safety Instruction HC 976 082206 Line art shown may not exactly match the fixture enclosed However the installation instructions do apply to this fixture Fill In Item Number On Carton And File This Sheet For Fixture Reference ITEM INSTALLATION HC 976 IF SUPPLY WIRES ARE LOCATED WITHIN 3 OF BALLAST USE WIRE RATED FOR AT LEAST 90 C STEP 1 Determine exact location on ceiling for fixture placement STEP 2 Feed the black and white ballast wires through the 7 8 wire exit hole of the fixture pan A STEP 3 Mount fixture to ceiling When mounting to drywall use molly bolts When mounting to ceiling joists use 1 1 4 screws recommended STEP 4 WIRING Take note of the color of the wire s on your fixture Identify which group your fixture wire s falls into and connect the wires according to the directions below GROUP A CONNECT TO BLACK GROUP B CONNECT TO WHITE HOUSE WIRE HOUSE WIRE BLACK WHITE PARALLEL WIRE ROUND amp SMOOTH PARALLEL WIRE SQUARE amp RIDGED NOTE When parallel wire is used the tracer wire is square shaped or ridged and the less tracer wire is round in shape or smooth Seen best when viewed from wire end To separate wires grasp the ends of each wire and pull apart A Place black wire from fixture evenly against black wi2. INSTALLATION AND SAFETY INSTRUCTIONS FOR YOUR SAFETY WARNING BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF EITHER THE FUSE REMOVED OR THE CIRCUIT BREAKER OFF GENERAL You do not need any special tools to install this fixture Be sure to fol low the steps in the order given Read instructions carefully If you are unclear as to how to proceed consult a qualified electrician NOTE In order for this lighting fixture to operate properly the buildings electrical system must be grounded If you are unclear as to how to proceed consult a qualified electrician NOTE FOR FIXTURES PROVIDED WITH 75 C OR 90 C SUPPLY WIRE WARNING ONLY THESE WARNINGS ARE PROVIDED ON THE U L LABEL AND ON THE FIXTURE CARTON RISK OF FIRE MOST DWELLINGS BUILT BEFORE 1985 HAVE SUPPLY WIRE RATED 60 C CONSULT A QUALIFIED ELECTRICIAN BEFORE INSTALLING 7 8 WIRE EXIT BALLAST ASSEMBLY STEP 1 Remove center cover B by squeezing cover together and pulling out of tabs C STEP 2 Remove 7 8 diameter wire exit plug and oval mounting knock outs by taking a screwdriver and punching out plug and knock outs from back side of fixture pan A Do not install on a ceiling that would cause the lift and shift mechanism to disengage ie slope ceiling drop ceiling etc STEP 3 Install one end cap O onto fixture pan A secure in place with cap nut E IF SUPPLY WIRES ARE LOCATED WITHIN 3 OF BALLAST USE WIRE R
3. re from the outlet box and twist together the bare parts of the metal B Fit a wire connector not supplied over the twisted wires and screw the connector clockwise until you feel a firm connection C Try gently to pull the connector off the wire If you can pull the connector off carefully re do steps A and B as above and check again for a firm connection D Connect the white wire from the fixture to the white wire from the outlet box in the same manner GROUNDING INSTRUCTIONS The green grounding screw is to be inserted into the hole with two raised dimples provided on the fixture pan Wrap the ground wire from the fixture if supplied and the ground wire from the outlet box bare metal or green insulated wire around the green grounding screw on the fixture pan If uninsulated wire is on the chassis connect the ground wire from the fixture if supplied and the outlet box to it using a small wire connector not supplied NOTE Underwriters Laboratories U L does not require all fixtures to have ground wires These fixtures still meet all U L specifications The listing mark of Underwriters on the product identifies products manufactured under its listing and Follow Up Service Programs NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES FINAL ASSEMBLY Make sure no bare wires can be seen outside wire connectors STEP 1 Install center cover B over fixture by squeezing center cover B together and in
4. sert under tabs C STEP 2 Install lamps STEP 3 Raise diffuser to fixture pan A and slide diffuser to meet up with D STEP 4 Install retaining end cap D and secure with cap nut E oO a fo ict Ee NOTE IN ORDER FOR THIS LIGHTING FIXTURE TO OPERATE PROPERLY THE BUILDING S ELECTRICAL SYSTEM MUST BE GROUNDED IF YOU ARE UNCLEAR AS HOW TO PROCEED CONSULT A QUALIFIED ELECTRICIAN CLEANING To clean wipe fixture body with a soft cloth Clean glass with a mild soap Do not use abrasive materials such as scouring pads powders steel wool or abrasive paper ORDERING PARTS Keep this sheet for future reference and in case you need to order replacement parts All parts for this fixture can be ordered from place of purchase Be sure to use exact wording from illustration when ordering parts
Download Pdf Manuals
Related Search