Sea Gull Lighting 7640-15 Installation Guide
Contents
1. lt NIPPLE C FIGURE 2 NOT SUPPLIED Sod gull lighting Installation And Safety Instruction HC 325 a27 Fill In Item Number On Carton And File This Sheet For Fixture Reference ITEM INSTALLATION HC 325 IMPORTANT DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX Secure mounting bar A to outlet box with outlet box screws not supplied Thread nut B on nipple C so that 3 threads are exposed above nut B Thread nipple C into mounting bar A and secure with nut B A Take note of the color of the wire s on your fixture Identify which group your fixture wire s falls into and connect the wires according to the directions below tT GROUP A CONNECT TO BLACK HOUSE WIRE GROUP B CONNECT TO WHITE HOUSE WIRE BLACK WHITE m ca PARALLEL WIRE ROUND amp SMOOTH PARALLEL WIRE SQUARE amp RIDGED SD e Note When parallel wire is used the tracer wire is square shaped or ridged and less tracer wire is round in shape or smooth Seen best when viewed from wire end To separate wires grasp the ends of each wire and pull apart B Take your fixture wire s from group A and place evenly against the black wire from the outlet box DO NOT twist wires together before using wire connectors C Fit a wire connector not supplied over the wires and thread the connector clockwise until you feel a firm resistance D Gently try to remove the wires from the connection If you can remove the wires2. carefully re do steps B and C as above and check again for a firm connection E Connect the fixture wire from group B to the white wire from the outlet box in the same manner GROUNDING INSTRUCTIONS The green grounding screw D is to be inserted into the hole with two raised dimples provided on the mounting bar A Wrap the ground wire from the fixture if supplied and the ground wire from the outlet box bare metal or green insulated wire around the green grounding screw D on the mounting bar A if uninsulated wire is on the mounting bar A connect the ground wire from the fixture if supplied and the outlet box to it using a small wire connector not supplied NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES FINAL ASSEMBLY Make sure no bare wires can be seen outside wire connectors After wires are connected tuck them carefully inside outlet box and then raise the fixture pan G against ceiling and secure with cap H Install lamps Cc gt STEP 3 Attaching diffuser D place diffuser D on an angle seating spring clips E on inside edge of diffuser D Push in remaining clips E with hand To release pull diffuser D down one side at a time Diffuser D will disengage CLEANING To clean wipe fixture body with a soft cloth Clean glass with a mild soap Do not use abrasive materials such as scouring pads or powders steel wool or abrasive paper ORDERING PARTS Keep
3. this sheet for future reference and in case you need to order replacement parts All parts for this fixture can be ordered from place of purchase Be sure to use exact wording from illustration when ordering parts
4. INSTALLATION AND SAFETY INSTRUCTIONS Be sure the electricity to the system you are working on is turned off either the fuse removed or the circuit breaker set at off Use of other manufacturers components will void warranty listing and create a potential safety hazard If you are unclear as to how to proceed contact a qualified electrician You don t need special tools to install this fixture Be sure to follow the steps in the order given Read instructions carefully Proper wiring is essential to the safe operation of this fixture Save these instructions WARNING FOR FIXTURES PROVIDED WITH 75 C OR 90 C SUPPLY WIRE WARNING ONLY THESE WARNINGS ARE PROVIDED ON THE LABEL AND ON THE FIXTURE CARTON WARNING RISK OF FIRE MOST DWELLINGS BUILT BEFORE 1985 HAVE SUPPLY WIRE RATED 60 C CONSULT A QUALIFIED ELECTRICIAN BEFORE INSTALLING OUTLET BOX GROUND WIRE WIRE CONNECTORS MOUNTING OUTLET BOX p SCREWS BARA NUT B NIPPLE C SPRING CLIPS E CAP NUT H E FIXTURE PAN G DIFFUSER D FIGURE 1 NOT INCLUDED Carefully remove the fixture from the carton and check that all parts are included as shown in figure 1 and 2 Be careful not to misplace any of the screws or parts which are needed to install this fixture GROUNDING AND MOUNTING BAR LOCK UP QUTLET BOX GROUND WIRE WIRE CONNECTORS MOUNTING BAR A OUTLET BOX SCREWS lt NUT B GROUNDING SCREW D
Download Pdf Manuals
Related Search