Home Decorators Collection AL14-22-NI Use and Care Manual
Contents
1. 5 HOMEDEPOT COM HOMEDECORATORS Please contact 1 800 986 3460 for further assistance Pre Installation continued PACKAGE CONTENTS B H C D E J B K L Part Description Quantity Part Description Quantity A Mounting bracket preassembled 1 G Rear guard preassembled 1 B Canopy 1 H Blade preassembled 1 C Canopy bottom cover preassembled 1 Front guard preassembled 1 D Hanger ball downrod assembly 1 J Receiver 1 E Coupling cover 1 K Remote control 1 F 1 L 1 Motor head preassembled Remote control holder Installation MOUNTING OPTIONS WARNING To reduce the risk of fire electric shock or other personal injury mount the fan only on an outlet box or supporting system marked acceptable for fan support of 35 Ibs 15 9 kg or less and use mounting screws provided with the outlet box Most outlet boxes commonly used for the support of lighting fixtures are not acceptable for fan support and may need to be replaced Consult a qualified electrician if in doubt AN WARNING This fan is not suitable for sloped ceilings If your ceiling fan does not have an existing UL listed mounting box then install one using the following instructions Disconnect the power by removing the fuses or turning off the circuit breakers Secure2. 14 Installing the Remote Control Holder 14 Care and Cleaning eere 15 Troubleshooting nn inen 15 Service Parts eec 17 Safety Information 1 Toreduce the risk of electric shock ensure electricity has been turned off at the circuit breaker or fuse box before beginning 2 All wiring must be in accordance with the National Electrical Code ANSI NFPA 70 1999 and local electrical codes Electrical installation should be performed by a qualified licensed electrician 3 The outlet box and support structure must be securely mounted and capable of reliably supporting a minimum of 35 Ibs Use only UL listed outlet boxes marked FOR FAN SUPPORT 4 Thefan must be mounted with a minimum of 7 ft clearance from the trailing edge of the blades to the floor 5 Avoid placing objects in the path of the blades 6 Toavoid personal injury or damage to the fan and other items be cautious when working around or cleaning the fan 7 Do not use water or detergents when cleaning the fan or fan blades A dry dust cloth or lightly dampened cloth will be suitable for most cleaning 8 After making electrical connections spliced conductors should be turned upward and pushed carefully up into the outlet box The wires should be spread apart with the grounded conductor and the equipment grounding conductor
3. S Disassembling Your Fan This fan comes with a pre assembled 1M rear guard G blade H and front guard I for your easy installation Check that all screws are tight and securely in place If you need to disassemble the fan for any reason such as cleaning follow these steps below Loosen the front guard screws Il to disassemble the front guard from the rear guard Remove the blade cover JJ from the blade H by turning the blade cover JJ clockwise Loosen the setscrew at the top of the blade head by using the hex wrench GG Remove the blade H from the motor shaft QQ Remove the rear guard from the motor head F by loosing the rear guard screws HH from the motor head F 13 HOMEDEPOT COM HOMEDECORATORS Please contact 1 800 986 3460 for further assistance Operation REMOTE CONTROL OPERATING INSTRUCTIONS Install the 12V MN21 A23 battery KK included into the remote control K To prevent damage to the remote control K remove the battery if not used for long periods Restore power to the ceiling fan and test for proper operation HI MED LOW buttons Sets the fan speed OFF button Turns the fan off KK C button This button is used for oscillating operation press the button to set the fan to 90 degree oscillation press again to turn off the oscillation and the fan will stay at the same direct
4. on one side of the outlet box and ungrounded conductor on the other side of the outlet box 9 Allsetscrews must be checked and retightened where necessary before installation 10 This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Warning Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving a
5. the above exclusion or limitation may not apply to you This warranty gives specific legal rights and you may also have other rights which vary from state to state This warranty supersedes all prior warranties Shipping costs for any return of product as part of a claim on the warranty must be paid by the customer Contact the Customer Service Team at 1 800 986 3460 or visit www HOMEDEPOT COM HOMEDECORATORS Pre Installation SPECIFICATIONS Fan size Speed Volts Amps Watts RPM CFM N W G W C F 22 in 120 bed am ee E oia i Medium 15 58 Ibs 21 601bs 7 High Intertek TOOLS REQUIRED Phillips Flat blade Step Wire Electrical screwdriver screwdriver ladder stripper tape Pre Installation continued HARDWARE INCLUDED NOTE Hardware shown to actual size unless noted otherwise in the table below v V JJ KK LL MM Description Quantity Collar setscrew preassembled 2 Plastic wire nut not to scale Canopy mounting bracket screw preassembled Remote control holder mounting screw not to scale Clevis pin preassembled Cotter pin preassembled Hex wrench not to scale Rear guard screw preassembled Il Front guard screw preassembled JJ Blade cover preassembled KK 12V MN21 A23 battery not to scale LL Stopper preassembled MM Plastic wire nut not to scale
6. HOME tempo DECORATORS Model AL14 22 BN COLLECTION USE AND CARE GUIDE BENTLEY 111 22 INCH CEILING FAN Questions problems missing parts Before returning to the store call Home Decorators Collection Customer Service 8 a m 7 p m EST Monday Friday 9 a m 6 p m EST Saturday 1 800 986 3460 HOMEDEPOT COM HOMEDECORATORS THANK YOU We appreciate the trust and confidence you have placed in Home Decorators Collection through the purchase of this ceiling fan We strive to continually create quality products designed to enhance your home Visit us online to see our full line of products available for your home improvement needs Thank you for choosing Home Decorators Collection Table of Contents Table of Contents Safety Information LECHE Pre Installation ecce eere ee eere enne SDGCITICaLlOTIS coc cn e YE E Dr Tools Required eicere Hardware Included eese Package Contents Installation Lcul Hanging the Disassembling Your 13 Operati M 14 Remote Control Operating Instructions
7. N NA N EISSN TX 1 NND EE A 2 7 777777 7 HA MA Assembly Hanging the Fan 4 Installing the mounting bracket 5 Hanging the fan from the mounting to the electrical box bracket Carefully lift the fan motor head F up to the mount WARNING To reduce the risk of fire electric shock or ing bracket A and seat the hanger ball downrod assembly D in the mounting bracket A socket other personal injury mount the fan only on an outlet box or A supporting system marked acceptable for fan support of 35 Ibs 15 9 kg or less and use mounting screws provided with the outlet box Pass the 120 volt supply wires through the center hole in the mounting bracket A Install the mounting bracket A to the outlet box NN with the screws and washers provided with the outlet box NN Securely tighten the two mounting screws 6 Installing the safety cable Secure the safety cable PP to the building structure using a wood screw not included 9 HOMEDEPOT COM HOMEDECORATORS Please contact 1 800 986 3460 for further assistance Assembly Hanging the Fan continued Preparing the receiver and remote control WARNING To avoid possible electrical shock be sure electricity is turned off at the main fuse box before wiring If you feel you do not have e
8. ab on the mounting bracket A properly sits in the groove in the hanger ball downrod assembly D before attaching the canopy B to the mounting bracket A by turning the canopy until it drops into place Tuck the connections neatly into the ceiling outlet box NN Slide the canopy B up to the mounting bracket A and place the key hole on the canopy B over the loose canopy mounting bracket screw CC on the mounting bracket A Turn the canopy B clockwise until the canopy B locks in place at the narrow section of the key holes Align the circular hole on the canopy B with the remaining hole on the mounting bracket A Secure the canopy mounting bracket screw CC previously removed in the hole and tighten the two canopy mounting bracket screws CC 12 A NOTE The stopper LL must be removed before operating your fan A NOTE Adjust the canopy mounting bracket screws CC as necessary until the canopy B and canopy bottom cover C are snug Attach the canopy bottom cover C to the canopy mounting screw heads CC on the bottom of the canopy B by inserting the canopy mounting screw heads CC into the key slots in the canopy bottom cover C and rotating the canopy bottom cover C clockwise Remove the stopper LL by pressing the clip on the stopper LL and sliding it forward off of the tube and fan assembly OQ N
9. er the hanger ball and remove the pin Remove all three pieces from the downrod and assemble them onto the new longer downrod before proceeding to the downrod installation Route the wires exiting from the top of the motor head F through the coupling cover E and the canopy bottom cover C Ensure the slot openings are on top Route the wires through the canopy B and then through the hanger ball downrod assembly D Align the holes at the bottom of the hanger ball downrod assembly D with the holes in the collar on top of the motor head F Carefully insert the clevis pin EE through the holes in the collar and the hanger ball downrod assembly D Be careful not to jam the clevis pin EE against the wiring inside the hanger ball downrod assembly D 2 Preparing the motor Remove the clevis pin EE cotter pin FF and loosen the two collar setscrews AA at the top of the motor head F collar The fan motor assembly A is shipped with a stopper LL to prevent movement during transportation Lp YH N Nm OKAY Insert the cotter pin FF through the hole near the end of the clevis pin EE until it snaps into the locked position Tighten the two collar setscrews AA at the top of the motor head collar SN H
10. fan motor assembly and fan guards are snug Make sure the blade and the blade cover are securely in place Allow a 24 hour breaking in period Most noises associated with a new fan disappear during this time Make sure there is a short distance from the ceiling to the canopy It should not touch the ceiling Make sure your ceiling box is secure and rubber isolator pads are used between mounting bracket and outlet box The remote control is not working Do not connect the fan with wall mounted variable speed control s Make sure the frequency switches are set correctly 15 HOMEDEPOT COM HOMEDECORATORS Please contact 1 800 986 3460 for further assistance Service Parts 2 Part Description Mounting bracket preassembled Canopy Canopy bottom cover preassembled Hanger ball downrod assembly Coupling cover Motor head preassembled Rear guard preassembled Blade preassembled Front guard preassembled Receiver Remote control Remote control holder s Po H Ye T gt J EE K L FF Part Description AA Collar setscrew preassembled Plastic wire nut Canopy mounting bracket screw preassembled Remote control holder mounting screw EE C
11. ion where the oscillation is turned off 90 oscillation INSTALLING THE REMOTE CONTROL HOLDER Attach the remote control holder L with the two remote control holder mounting screws DD 14 Care and Cleaning tarnishing shoe polish Clean your fan periodically Use only a soft brush or lint free cloth to avoid scratching the finish The plating is sealed with a lacquer to minimize discoloration or Optional Cover small scratches with a light application of Do Do not Check the support connections brackets and blade Use water when cleaning Water could damage the motor attachments twice a year Make sure they are secure or the wood or possibly cause an electrical shock Because of the fan s natural movement some connections may become loose over time It is not Apply oil to your fan or motor The motor has necessary to remove the fan from the ceiling permanently lubricated sealed ball bearings Troubleshooting panel box before you attempt any repairs Refer to step 8 WARNING sure the power is off at the electrical Making the electrical connections on page 11 Problem Solution The fan will not start Check the main and branch circuit fuses or breakers Check the line wire connections to the fan The fan sounds noisy Make sure all screws on
12. levis pin preassembled FF Cotter pin preassembled GG Hex wrench HH Rear guard screw preassembled ll Front guard screw preassembled JJ Blade cover preassembled KK 12V MN21 A23 battery LL Rubber packing mount preassembled MM Plastic wire nut 16 HOME DECORATORS COLLECTION Questions problems missing parts Before returning to the store call Home Decorators Collection Customer Service 8 a m 7 p m EST Monday Friday 9 a m 6 p m EST Saturday 1 800 986 3460 HOMEDEPOT COM HOMEDECORATORS Retain this manual for future use AL14 22 BN00001 A
13. model if the product is returned To obtain warranty service you must present a copy of the receipt as proof of purchase All costs of removing and reinstalling the product are your responsibility Damage to any part such as by accident misuse improper installa tion or by affixing any accessories is not covered by this warranty Because of varying climatic conditions this warranty does not cover any changes in brass finish including rusting pitting corroding tarnishing or peeling Brass finishes of this type give their longest useful life when protected from varying weather conditions A certain amount of wobble is normal and should not be considered a defect Servicing performed by unauthorized persons shall render the warranty invalid There is no other express warranty We hereby disclaim any and all warranties including but not limited to those of merchantability and fitness for a particular purpose to the extent permitted by law The duration of any implied warranty which cannot be disclaimed is limited to the time period as specified in the express warranty Some states do not allow limitation on how long an implied warranty lasts so the above limitation may not apply to you The retailer shall not be liable for incidental consequential or special damages arising out of or in connection with product use or performance except as may otherwise be accorded by law Some states do not allow the exclusion of incidental or consequential damages so
14. nect the black wire from the fan to the black wire marked TO MOTOR L from the receiver J Connect the white wire from the fan to the white wire marked TO MOTOR N from the receiver J Connect the blue wire from the fan to the blue wire marked Oscillation from the receiver J Receiver to house supply wires electrical connections Connect the black hot wire from the ceiling to the black wire marked AC in L from the receiver J Connect the white neutral wire from the ceiling to the white wire marked AC in N from the receiver J 11 If your outlet box NN has a ground wire green or bare copper connect it to the fan ground wires otherwise connect the hanger ball downrod assembly D ground wire to the mounting bracket A Secure each wire connection with a plastic wire nut AA provided with the electrical hardware After connecting the wires spread them apart so that the green and white wires are on one side of the outlet box NN and the black and blue wires are on the other side Carefully tuck the wire connections up into the outlet box NN Ground Black White conductor HOMEDEPOT COM HOMEDECORATORS Please contact 1 800 986 3460 for further assistance Assembly Hanging the Fan continued 9 Installing the canopy 10 Attaching the canopy bottom cover to the canopy A WARNING Make sure the t
15. nough electrical wiring knowledge or experience have your fan installed by a licensed electrician This remote control unit is equipped with 16 code combinations to prevent possible interference from or to other remote units The frequency switches on your receiver J and remote control K have been preset at the factory Please recheck to make sure the switches on the remote control K and the receiver J are set to the same position Any combination of settings will operate the fan as long as the switches in the remote control K and receiver J are set to the same position After checking the switches insert the receiver J into the mounting bracket A with the flat side of the receiver J facing the ceiling 10 Assembly Hanging the Fan continued 8 Making the electrical connections including ground and that no bare wire is visible at the wire WARNING Check to see that all connections are tight nuts except for the ground wire 20 ft from the remote control for proper signal transmission j NOTE The fan must be installed at a maximum distance of between the remote control and the fan s receiving unit Follow the steps below to connect the fan to your household wiring Use the plastic wire nuts AA with your fan Secure the plastic wire nuts AA with electrical tape Make sure there are no loose strands or connections Motor to receiver electrical connections Con
16. ntenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help WARNING To reduce the risk of electrical shock or fire do AN not use this fan with any solid state fan speed control device It will permanently damage the electronic circuitry WARNING Do not insert foreign objects between rotating fan blades WARNING To reduce the risk of fire electric shock or personal injury mount the fan to the outlet box marked acceptable for fan support with the screws provided with the outlet box CAUTION To reduce the risk of personal injury use only the screws provided with the outlet box HOMEDEPOT COM HOMEDECORATORS Please contact 1 800 986 3460 for further assistance Warranty We warrant the fan motor to be free from defects in workmanship and material present at time of shipment from the factory for a period of lifetime after the date of purchase by the original purchaser We also warrant that all other fan parts excluding any glass or acrylic blades to be free from defects in workmanship and material at the time of shipment from the factory for a period of two years after the date of purchase by the original purchaser We agree to correct such defects without charge or at our option replace with a comparable or superior
17. the outlet box NN not included directly to the building structure Use appropriate fasteners and materials not included The outlet box and its bracing must be able to fully support the weight of the moving fan at least 35 Ibs Do not use a plastic outlet box The illustrations below show two different ways to mount the outlet box NN not included NN To hang your fan where there is an existing fixture but no ceiling joist you may need an installation hanger bar 00 not included as shown above HOMEDEPOT COM HOMEDECORATORS Please contact 1 800 986 3460 for further assistance Assembly 1 Preparing the canopy Remove the canopy bottom cover C from the canopy B by turning the canopy bottom cover C counter clockwise Remove the mounting bracket A from the canopy B by removing the non slotted canopy mounting screw CC from the bottom of the canopy B and loosening the slotted canopy mounting screw CC a half turn from the screw head Next turn the canopy B counterclockwise to remove the mounting bracket A from the canopy B CC Assembling the fan WARNING Failure to properly install the cotter pin FF could result in the fan loosening and possibly falling NOTE If a longer downrod not included is needed take out the screw located in the hanger ball you need to use the hex wrench GG to loosen your set screw low
Download Pdf Manuals
Related Search