EarthMinded PRN1001 Installation Guide
Contents
1. WARNING A Tipping Hazard WARNING WARNING Stored rainwater is not suitable for human or animal consumption A Contamination Hazard 1 A Watering Can or Bucket can be filled by using the spigot or by removing the lid to dunk and fill 2 A Garden Hose can be connected to the spigot or bottom drain for watering remote areas The barrel must be higher than the area to be watered Elevating the rain barrel will improve water pressure turned on off as needed Linking barrels There are two ways that barrels can be linked together to increase the water storage capacity Option A Linking barrels rim to rim using the fill hose provided The barrel connected to the downspout will fill first then overflow into the second barrel 1 Drill a second water inlet hole in the first barrel at 3 75mm below the rim using the MID SIZE 1 5 hole saw Insert the second water fitting provided in the parts kit Connect the end of the fill hose to link the first and second barrels Option A Rim to Rim 5 Troubleshooting The barrel does not fill with water after rainfall 1 Check the top of the gutter for blockage at the downspout connec tion Remove the FlexiFit Diverter and check that the downspout di verter and fill hose are not blocked by leaves or debris Make sure the diverter is installed with the collection cup arrow facing up Make sure no point of the fill hose is above the2. Wear Safety Glasses WARNING Soapy water or hand lotion on the hose cuff and rubber seal reduces friction and makes insertion easier Wear Safety Gloves 4 Place the Do Not Drink Water WARNING sticker on the barrel above the spigot If using an open top barrel with lid make sure the lid is secure and latched Do not leave the lid off for extended periods of time as the barrel may bow from the weight of the water and make fitting the lid difficult I R IA 2 Winterizing the barrel A rain barrel can be damaged if water is allowed to freeze in the barrel To Winterize 1 Barrels can be cleaned using soft scrub and a mild scouring pad If using Disconnect the FlexiFit Diverter by removing the 2 screws Remove the diverter by pulling it out in an upwards motion Completely drain the barrel making sure the water is being drained away from the foundation of the house Plug the hole in the downspout with the winter hole cover and secure with the 2 screws a sealed container a small amount of bleach can be added to the water inside the barrel to remove algae and stains Drain water and dispose of properly 13 Using Your rain barrel There are several ways to access and distribute the water in the barrel Use as much stored water as often as possible to make room for new rainwater RA the bucket or watering can
3. 4 Select a location for your rainbarrel Before assembling the parts to the barrel we recommend that you select and prepare the location where the barrel will be used This will help you locate the fittings on the barrel in the most convenient location Choose a downspout that is near the plants or beds to be watered The downspout must be a 2 x 3 or 3 x 4 rectangular type The barrel must be located within 3 feet of the downspout to se the Place the barrel in the intended location with the front facing out 1 Mark the front of the barrel This will be the side with the spigot facing out The spigot should be located on a flat or evenly curved surface without ridges or features that can affect the water seal 2 Hold the fill hose in position between the barrel and the downspout and mark the water inlet location on the rim of the barrel This mark can be at fill hose provided the back right or left side of the barrel Check that the hose can reach horizontally from the rim of the barrel to the The ground under the barrel must be level and firm A solid surface downspout base of wood pavers or stone is recommended If the surface is not level use a shovel or rake to grade the surface Check by placing a level on the rim of the barrel before continuing EarthMinded Do it Yourself Rain Barrel Diverter and Parts Kit User Guide RBK OO0O1 V 1 EarthMinded has assembled all the parts needed to mak
4. level of the diverter Check that the diverter is installed at the correct height It must be above the water inlet on the barrel to fill properly To Correct drain the barrel and lower the ground until the water inlet on barrel is 1 below the level of the diverter Check the spigot and drain to make sure that water is not leaking Even a slow leak will drain the barrel over time The barrel overflows and water leaks out from the lid The barrel is too low To correct drain the barrel and construct a solid surface base to raise the barrel to the correct height according to the instructions The diverter collects too much water To correct an optional overflow hose can be added to the rim of the barrel to drain off excess water using the second seal provided in the kit The fill hose can be replaced by a1 1 4 bilge hose available at most home centers 3 A Soaker Hose can be connected to the spigot or bottom drain If connecting to bottom drain an inline garden hose valve should be fitted in place of the drain cap This will allow the water to be 4 A Garden Hose Timer can be fitted between bottom drain and soaker hose to automatically dis pense water at regular intervals Be sure the timer is designed for low pressure applications If connecting to a drip irrigation system use emmiters designed for 4 gallons per hour Always be sure to tighten spigot after use Even a slow drip will empty the barrel over time Opt
5. containers only measure 2 5 inches 65mm below the reference line and make a second mark at the CENTER of the downspout Sealed Barrel 9 Drilling the FlexiFit diverter hole Drill a hole in the downspout using the LARGE 2 1 8 hole saw The center bit of the hole saw should align with the center mark on the downspout a Do not force the hole saw Cut slow and steady keeping a firm hold on the drill b Always use safety glasses and gloves when cutting or drilling c The cut edges of the downspout can be sharp Wear protective safety glasses and gloves when handling d For 3 x 4 downspouts make sure you drill the hole on the nar row 3 side Installing the FlexiFit diverter lk sist flat against the downspout Do not twist the diverter when installing push it straight in with the cup facing up at all times to insure a proper seal Make sure that the arrow on the front of the diverter is installed pointing straight up 2 Use 2 of the self tapping screws to attach the diverter to the downspout 3 Connect the fill hose to the cuff end of the FlexiFit diverter Press the hose into the diverter until the corrugated section is flush against the diverter Use soapy water or hand lotion on the hose cuff and seal to reduce friction and improve fit 11 Connecting the barrel 1 2 Press the hose end firmly into the water seal un
6. d provide quick access to the water using a bucket or watering can but present a safety concern for children the lid must always be latched and locked if possible Water weighs 8 3 lbs per gallon Be sure to select a sturdy container that can support the weight when full 55 gallons weighs 456 Ibs WARNING Stored rainwater is not suitable for human or animal consumption If the hole is cut too high water will overflow from the barrel rim this only applies to open top barrels Not for use with round downspouts This kit is not recommended for use with metal drums or barrels INCORRECT If the hole is cut too low the barrel will not fill WARNING Damage to home or property may occur if improperly installed mm D om INCORRECT For open top containers only If the hole is cut too high water will overflow from the barrel rim Plastic Waste Barrel Open Top Wood Barrel Recycled Plastic Barrel Sealed CORRECT DIY Instructions 10 26 10 indd 1 D 10 26 10 6 47 PM 8 DO NOT CUT THE DOWNSPOUT UNTIL READING STEP 9 k Marking the FlexiFit diverter hole on downspout Mark a reference line even with the barrel rim on the downspout using a pencil and a straight edge placed on the rim of the barrel as a guide For sealed containers no opening lid measure and mark the CEN TER line of the downspout For open top
7. e a rain barrel using a recycled barrel or plastic trash barrel barrel not included Using this kit anyone who can use a drill can make and install a rain barrel in minutes Please read all instructions and warnings before installation and retain this Booklet for future reference Las instrucciones en espa ol se pueden bajar en www earthminded com espanol Top View onrerns ni 1 1 J4 32mm Ay a x Hole Saw F 5 A 5 x oe i Option B Mid height spigot with bottom drain e 1 General description Rain barrels have been used for hundreds of years to harvest and The FlexiFit diverter helos prevent mosquitoes pests and store rainwater for use with plants gardens and other outdoor algae causing sunlight from entering the barrel The diverter chores is easy to remove from the downspout and the kit includes a EarthMinded s DIY Rain Barrel Kit is a state of the art sealed winterizing hole cover 5 Installing the front fitting on the barrel There are 2 options for installing the front fittings Option A has a single spigot st the bottom of the barrel and is recommended if you will only be using a garden hose to access the water in the barrel This configuration gives access to all the water in the barrel A stand is recommended to incread water pressure Option B has a mid height spigot and a bottom 1 Mark the spigot hole Find the front of the barrel measure up 12 35mm from the bottom of the bar
8. he water inlet hole Tools needed s 4 3y A Make sure the inlet is located on a flat or evenly curved surface avoid I 1 1 1 Safety Glasses ridges or other features that could affect the water seal I I 38 mm 2 Drill a hole using the MEDIUM 1 1 2 hole saw included in the set I ee y HoleSaw 3 Insert the threaded rubber seal into the hole Pinch the seal into a U AN a shape for easier insertion g g 2 Safety Gloves p aen Ta P D9 Flexifit Diverter Sticker RK 001 p Rubber Seals s Z Drill RB 009 a i Threaded Rubber Seal Barrel Not Spigot ae Included E Winter Hole i casein Cover Tape or Ruler RB 004 5 Pencil CESS Drain Connector RB 006 N Drain Cap Instructions 6 Scissors RK 015 Vinjes 7 Phillips Rubber Washer Rubber Seal RB 008 RB 010 Screwdriver Level ___ 7 S _ 7 Oo Back of barrel 3 Selecting a container EarthMinded supplies only the parts and fittings to be added toa barrel you supply Therefore we take no responsibility for losses damages or injury caused by failure of the barrel or improper installation of the parts Follow these instructions carefully for successful results 7 About the FlexiFit diverter DO NOT CUT THE DOWNSPOUT UNTIL READING STEPS 8 AND 9 The Flexifit diverter redirects water from your downspout to the barrel and automatically passes water through the downspout when the barrel is ful
9. ion B Linking barrels bottom drain to bottom drain using a modified garden hose With this method both barrels will fill up at the same level The second barrel can be placed further away from the first as long as the ground is level between barrels This is useful for patios decks or level foundations where a second barrel can be located away from the downspout This method requires that a female garden hose end or male to female hose adaptor be purchased not included Attach one end of the garden hose to the bottom drain on the first barrel 1 The hose can be cut to length and fitted with a female hose end connector Connect the hose to the drain on the second barrel 3 Make sure the rims of both barrels are at the same level Option B Bottom Drain to Bottom Drain Warnings regarding potential hazards x Wear Safety Glasses Wear Safety Gloves p a b Tta Drowning Hazard A Contamination Hazard A 4 a k TA Electrocution Hazard AN Installation Hazard A gt AR d C b Ya Tilting Tipping Hazard Infestation Hazard A 4 a Wr WARNING Lid must be secured at all times to prevent injury to children WARNING The barrel must be installed on a solid and level base WARNING Stored rainwater not for human or animal consumption 10 26 10 6 47 PM
10. l of rainwater Select a sturdy watertight container IMPORTANT There are two ways to install the diverter depending on the type of barrel you use If the barrel is a sealed container without a lid the diverter can be located at the same level as the rim of the barrel or higher This will improve the filling efficiency of the diverter a A heavy duty or commercial grade plastic waste barrel with latching lid b A traditional wood barrel can make an attractive and natural looking rain barrel Make sure it is in good condition clean and watertight c If using a recycled barrel use only FDA approved food grade 1 The hole must be cut at the correct height for the diverter to work barrels Make sure the barrel is clean and has not been used to properly contain toxic or hazardous substances If the hole is cut too low the barrel will not fill properly The container selected should be sealed or have a latching lid to prevent mosquitoes animals and children from entering the barrel If the barrel has an opening lid the center of the diverter hole must be drilled 2 5 65mm below the level of the rim of the barrel to prevent water from leaking from the lid seam The diverter will not work if it is placed below the level of the water inlet on the barrel The diverter is installed in a hole that is cut in the downspout This Kit will work on both sealed barrels and open top barrels with lids p Open top barrels are easier to clean an
11. rel and mark the center for the mid height spigot hole rainwater collection system when used with a barrel or container you supply Our patented FlexiFit diverter installs easily by drilling a single hole into any standard 2 x 3 or 3 x 4 The FlexiFit diverter offers many advantages over conventional top fill rain barrels that commonly flood with heavy rain require permanent modifications to your downspout and use unsightly drain and is recommended for use with a watering can Option A Bottom spigot only 2 Mark the drain hole Measure up 2 5 65mm from the bottom of the barrel and mark the center for the drain hole If you plan on connect ing a garden or soaker hose to the drain fitting we recommend that rectangular downspout The diverter sends rainwater into the overflow hoses 1 Find the front of the barrel measure up 2 5 65mm from the bottom the drain be located 6 15mm off center to the left or right side of barrel o te elias ee the curiae will automatically pass of the barrel and mark the center for the spigot hole Drill a hole using the spigot to give clearance for filling the watering can excess water throu e downspout 1 4 i i g P the SMALL 1 1 4 hole saw included in the set 3 Drill 2 holes on these marks using the SMALL 1 1 4 hole saw 2 Insert the threaded rubber seal into the hole Pinch the seal into a U included in the set You may need to remove the slug of pla
12. stic from i Spigot shape for easier insertion the end of the hole saw after drilling the first hole ee raiocer heed 3 Thread the spigot into the seal until the hex collar on the spigot sits 4 Insert 2 threaded rubber seals into both the spigot and drain holes tachment firmly against the seal and the water outlet points down Soapy water Pinch the seal into a U shape for easier insertion l or hand lotion on the threads will reduce friction and imptove fit 5 Thread the spigot and drain into the seal until the hex collar sits firmly Fill hose a against the seal Soapy water or hand lotion will reduce friction and 4 FlexiFit Diverter provenit Pinch the threaded rubber seal into a C shape before inserting into the hole in the barrel ge Soapy water or hand lotion on the hose cuff and rubber seal reduces friction and makes insertion easier 5 Winter hole cover Some areas prohibit the use of rain barrels Please check local regulations before installing WARNING Stored rainwater not for human or animal consumption Optional Stand Open Top Container Sealed Barrel Option A Option B 2 Parts list 3 Pc Hole Saw Set Fill Hose RK O11 RB 013 6 Installing the water inlet fitting prt ny I x 1 Locate the water inlet mark on the rim of the barrel from Step 4 AY Measure down 3 75mm and mark the center for t
13. til the corrugated sec Connect the other end of the fill hose to the water inlet on the barrel tion is flush with the water seal Use soapy water or hand lotion on the hose cuff and seal to reduce friction and improve fit 3 The hose can be cut at 1 intervals along the ridge at the center of the flat cuffs to shorten if needed DO NOT CUT THE HOSE ON THE CORRUGATED SECTION l Soapy water or hand lotion on the hose cuff and rubber seal reduces friction and makes insertion easier DIY Instructions 10 26 10 indd 2 Insert the diverter into the hole in the downspout by squeezing the sides and pushing the diverter into the downspout until the flange Be sure to take an elevated base into account before measuring If you plan on using an elevated base you must do it before measuring and cutting the downspout An elevated base made from wood or brick will increase water pressure if using with a garden hose When installing to a 3 x 4 rectangular downspout make the mark on the narrow 3 side Be sure to drill the hole on this narrow side of the downspout not the front for the diverter to work properly WARNING Installation Hazard WARNING A Electrocution Hazard WARNING Installation Hazard WARNING A Electrocution Hazard Open Top Container CrD Wear Safety Glasses WARNING Wear Safety Gloves Tap
Download Pdf Manuals
Related Search