Kenroy Home 50053STST Instructions / Assembly
Contents
1. the fountain body 3 Attach LED cluster assembly C bracket into metal slot on the back of fountain body as shown 4 Feed cord from LED cluster assembly C behind metal bracket following the water tube 5 Place roof onto the fountain body and secure with clips which are attached to back of fountain body 6 Peel paper backing from the wall spacer pad J and apply to back of the basin as shown FOR WALL MOUNTED APPLICATIONS Al Locate desired position on the wall Use a level to draw a line on the wall place bracket E to the wall and mark three mounting holes A2 Based on your specific wall material wallboard sheet rock plaster concrete etc consult local hardware store or professional to determine the appropriate anchor type for 3 pieces to hold the weight of your fountain NOTE This fountain is about 40 lbs after filled with water Consult local hardware store or professional for proper instructions for installation of anchors screws for wall bracket E Then secure the bracket E to the wall with three screws The angled part of the wall bracket E should be on the top when installing Warning Using incorrect or under specified fasteners could result in an unstable or dangerous condition A3 Feed pump A power cord through the hole in back of the fountain body Make sure the light cord is behind metal bracket Ref Step 4 then join the light connectors and screw the cap to connector tigh2. AN KenroyHome ALL TOGETHER BETTER USE AND CARE GUIDE FLOOR WALL FOUNTAIN Questions problems missing parts Please call Kenroy Home Customer Service at 904 642 4340 or send email to customerservice kenroyhome com WWW KENROYHOME COM MODEL 50049BRZ S0053STST PACKING DIAGRAM j 2 WALL SPACER PADS WATER GUIDING PAD A BAG OF RIVER STONES 2 ANCHORS AND 2 SCREW FOR CORD COVER INNER BOX FOR LED CLUSTER PUMP AND TRANSFORMER BRACKET FOUNTAIN BODY ARDBOARD 2 CORD COVERS AND CHANNEL STYROFOAM 16 KGS ID STYROFOAM 16 KGS MODEL 50049BRZ 350053STST ASSEMBLY INSTRUCTIONS READ AND SAVE THESE INSTRUCTIONS Read instructions all the way through prior to assembly This fountain should take approximately 15 minutes to assemble Make sure all parts are firmly tightened TOOLS REQUIRED Level Pencil Phillips screwdriver PARTS LIST Pump A Transformer B Water Diffuser D Bracket E a ll RSs Channel amp 2 cord covers G A bag of river stones H 2 Wall Spacer Pads J Pump Connector K LED Cluster Assembly C Lid F Water Guiding Pad I 2 Anchors amp 2 Screws M for cord cover FOUNTAIN ASSEMBLY 1 Remove roof from the fountain body then remove water diffuser D from top of the fountain body 2 Remove plastic cover from water diffuser D and replace the water diffuser D back into the top of
3. ning and adjust the water valve on the pump A if needed Use the water guiding pad I to brush the fountain face to provide a better water flow when first turning fountain on 9 Place lid F into basin to cover the basin make sure the open side facing up Then place decorative river stones H into the lid F 10 Join the connector from pump A to transformer B and screw the cap to connect the parts tightly together re 11 Plug power cord into socket and your new fountain is ready for use Trouble shooting 1 If your fountain does not work check plug at the socket Make sure the plug is fully and properly inserted into the wall outlet 2 Next check to make sure the outlet is powered 3 If you reconnected the pump sometimes the water would not flow please turn off the power and turn back on to help release air in the line 4 If the fountain still does not work or you are unhappy with anything about this product call us at 904 642 4340 or send email to customerservice kenroyhome com Please do not return your product to the store where you purchased it call us for a quick resolution Splashing disclaimer Splashing may occur when fountain is initially turned on Protect surrounding surfaces as needed Important pump information Pump must be fully submersed in water while operating Water To reduce mineral deposits and bacteria build up the use of distilled water is recommended Important safety instr
4. tly together A4 Insert pump connector K into the hole of pump A then place the pump A into the basin A5 Align bracket E on the wall with bracket on the back of fountain hang fountain body securely on bracket E attached to the wall make sure the bracket on the back of fountain is on the top of the wall bracket E A6 To install the anchors M for the cord cover channel G place the cord cover channel G on the wall and mark two mounting holes Gently tap or press the tip into the drywall make sure the flat side of the anchor is flush with the wall If you encounter a wall stud while installing the anchors M please use the mounting screws M without the anchor Then secure the cord cover channel to the wall with two screws M a A7 Place power cord inside cord cover channel G and press cord cover securely onto the channel G FOR FLOOR APPLICATIONS B1 Feed pump A power cord through the hole in back of the fountain body Make sure the light cord is behind the metal bracket Ref Step 4 then join the light connectors and screw the cap to connect the parts tightly together basin B3 Place the fountain body onto the desired flat floor and against the wall 7 Fill the basin with enough water to completely submerse pump A The basin holds 1 7 gallons of water Distilled water is recommended to reduce mineral deposits and bacteria build up nm 8 Test the water run
5. uctions This fountain is rated for indoor and outdoor use Warning Once a week inspect fountain floor and adjacent wall for moisture build up and clean as necessary This is especially important for humid environments This unit must be connected to a supply circuit that is protected by a ground fault circuit interrupter GFCI The GFCI should be tested on a routine basis To test the GFCI push the test button The GFCI should interrupt power Push the reset button Power should be restored If the GFCI fails to operate in this manner the GFCI is defective
Download Pdf Manuals
Related Search