Havahart 1088 Instructions / Assembly
Contents
1. Models 1088 amp 1089 1 Study illustration 1 to familiarize yourself with the parts of the trap 2 With one hand grab the handle 1 on the top of the cage Lift the trap Trap will drop into place illustration 2 3 Notice the frame rods 2 amp 3 are hanging below the trap Note Model 1088 has only one frame rod 2 that is attached to the top front of the cage trap Gently lower the trap to the ground so that the open ends of the frame rods point to the back of the trap illustration 3 4 Bring the front frame rod 2 up to the front frame clips 4 Hold the frame clips out one at a time and snap the front frame rod into place illustration 4 Remember to clip both sides of the front frame rod 5 For Model 1089 only Repeat step 4 for the back frame rod 3 Remember to clip both sides of the back frame rod into the back frame clips 5 Does not apply to Model 1088 6 Remove the U shaped lock rod 6 from storage area at top of the trap illustration 5 After removing the lock rod close back panel 7 Back panel should swing down when lock rod is removed 7 Turn trap so you are facing the back panel 7 With the straight end of the U shaped lock rod 6 closest to the ground take your right hand and thread the straight end of the lock rod through the bottom hole of the retainer clip 8 and the hooked part of the lock rod through the side of the Illustration 3 trap illustration 6 Thread rod th2. clear of the animal s exit path If necessary use hook of the U shaped lock rod to hook the bottom of the back panel and pull back panel outward pull out and up illustration 13 Walk away from the trap The animal will exit the trap on its Own On Model 1089 only Lift lock 10 on trap Does not apply to model 1088 Lift the door up and insert stick through both sides of the trap to prop the door open illustration 14 Walk away from trap Animal will exit trap E TIBI nl Laer 1 I n LA it nA ET SHB We AR aF H Remove U shaped lock rod from the back panel Face trap so trigger rod 14 is toward you Unclip front and back frame rods back frame rod is on 1089 only Lay frame rods flat Tip trap away from you pull trigger rod out of trigger pan Place trigger rod end into the storage area in the mesh at the top of the trap For Model 1089 only With right hand lift door lock on trap Does not apply to Model 1088 Lift trap door and hold open with left hand With right hand push back panel toward the front of trap and hold it open Collapse trap by pushing top of trap away from you and then down Fold bottom of trap under the top of trap Place U shaped lock rod in the storage area top one inch of mesh at the back of the trap so that back panel is secure mulini mlt Pas T AES ri Ralf sjan r ME LT Lah boit dT a ES Illustration 13 Illustration 14
3. Instructions for Model 1088 amp 1089 Collapsible Cage Traps Handle Poign e Manga Front Frame Rod fige qu Carina Goutral for Small Animale 10 cadre avant Barra de Pasca 7 Estructura de la parte cel da o Frente RT 1039 Back Frame Rod ic bat ip Tige du cadre arri re TT nas i mod le 1089 Barra de muli sn THL N Estructura de la Parte de E dir i ELL 6 Atr s modelo 1089 mL COTE DEL EI one Front Frame Clip Pi pai sE FEE p AI ie eae nb El ret CRETE Ine TT ROUE e mt E T US PRE RS 1089 Back Frame Clip 4 HT LE F Paton D S LEP LL EC AE Pince du cadre arri re EN I je ber Le dre REEEETETU ean ET n mod le 1089 Presilla de LT n L TEE F ara IRE ie atr s modelo 1089 TETI Sen U Shaped Lock Rod 7ige he IE SE LT T E I a de verrou en Ui gancho de V I Tessa So gt M RSs SUR cierre en forma de U eA EE a ae ee te al a el Ca RE g Back Panel Panneau 12 7X E ESSE IEEE iSc arri re parel de atr s a Tz OL CEE SE PES IM q Retainer Clip Pisce de VO L da ssa Sl a ac retenue retenedor NE e pm as 5 Trigger Pan Aateay de ICONE 14 3 d tente bandeja de Gatillo 11 2 Door Lock eron Cerrad Illustration 1 Model 1089 ET porte Gancho de la Puerta Door Lock Frame Cadre de verroy de porte Estructura de la cerradura de la Puerta Trigger D tente Gatillo Trigger Rod Tige de Setting up Collapsible Cage Trap
4. er of your left hand through the loop 11 on the door of the trap and with your thumb push the lock frame 12 and lift the door illustration 10 4 Set trap by pulling metal trigger 13 forward with your right thumb and forefinger until door is secured by trigger hook illustration 11 5 Gently release door Trap is set 6 Trip trap to make sure it is working properly Trip trap using a pen or pencil sticking an end through the side of the trap and pushing down on the end of the trigger pan FT Fu rie het MIL Tips For smaller animals use a light trigger release setting Place just the tip of the trigger rod under the door cross rod illustration 12 Release Relocation of Captured Animals Note Note Check with your local or state Game Commission to determine the lawful method of disposing of a captured wild or nuisance animal Caution DO NOT ATTEMPT TO HANDLE CAPTURED ANIMALS DO NOT LEAVE CHILDREN UNATTENDED NEAR A CAPTURED ANIMAL Illustration 8 Releasing Captured Animal Through Back Panel Releasing Captured Animal Through Trap Door To Collapse Models 1088 amp 1089 9 10 Retain carton for trap storage Approach trap cautiously and quietly so you don t excite the animal Stand trap on front door Pull out the U shaped lock rod at the back of the trap by pressing in on left side of trap and releasing hook on lock rod When finished return trap to its normal position Stand
5. rough two retainer rings attached to the back panel so the back of the trap is secure Thread straight end of lock rod through the bottom hole of the retainer clip on the left side of the trap With your left hand secure the hooked part of the lock rod to the left side of the trap illustration 7 8 Remove trigger rod 14 from storage area at the top of the trap illustration 8 Tipping trap away from you thread trigger into loops on the underside of trigger pan 9 illustration 9 Return trap to its upright position 9 Trap is now set up 10 Carton may be retained for trap storage Baiting Instructions for Models 1088 amp 1089 1 Remove U shaped lock rod 6 from the back panel 7 by pressing in on left side of trap to release hooked part of lock rod Pull back panel toward you 2 While holding back panel in an upright position place the bait approximately two inches from the back of the trap Do not place bait on the trigger pan 9 3 Close back panel amp relock using U shaped lock rod REMEMBER Always bait the trap before setting it Setting Instructions for Models 1088 amp 1089 REMEMBER REMEMBER Any camouflage or material you use to hide the trap should not interfere with the operation of the trap in any way 1 Viewing trap from front position yourself on the right hand side of trap 2 For Model 1089 only lift the lock 10 with your right hand Does not apply to Model 1088 3 Place the forefing
Download Pdf Manuals
Related Search