Lifegard Aquatics R440468 Installation Guide
Contents
1. 15 seconds Model 2780 will attempt to turn itself on automatically if water is present and will try again every 10 minutes This will occur a total of 5 times It will then try to start once every 24 hours for 30 days After this it will stop and you will need to disconnect and plug the pump back into an electrical power source to reset itself Attention Make sure the outlet discharge pipe is empty of water when starting the pump Air pockets inside the outlet line can have a negative effect on the pump performance If air pockets exist turn the pump off and wait a few seconds before turning back on This should correct the problem Noise generated in Models 1430 and 2100 for short periods usually at start up is caused by the pumps ability to clean itself by turning repeatedly back and forth clockwise and counter clockwise removing any debris that can block the pre chamber This self clean ing function reduces the time necessary for maintenance Warranty Lifegard Aquatics warrants to the original purchaser this product to be ree from defects in material or workmanship for a period of one year rom the date of purchase provided it is operated in accordance with actory instructions and operated within the environment and limitations or which it is designed Lifegard will not be liable for any labor cost of removing or replacing component parts This shall be the responsibility of the original purchaser as will be shipping char2. than 95 degrees F Keep these instructions in a safeplace for future reference l Keep out of reach of children EEEE H YY TA Y Cleaning Easy simple cleaning is required for the pump to operate correctly Disconnect the power cord form electrical supply before performing any maintenance Remove the bottom grill A by pushing release tabs Y Rinse all parts in running water using a small brush to remove any debris Make sure pre chamber C is clean of any debris Maintenance Remove the bottom grill A by pushing the release tabs Y Loosen screw I and gently remove the pre chamber C and rotor assembly composed of the shaft EFH and the rotor G Remove the rotor G being careful not to lose the rear rubber cap H Rinse all parts in running water using a small brush to remove any scale Clean the o ring D fitted on the pre chamber G and make sure it is clean and in good condition Replace if it is damaged Reassemble the pump PUSH lt Use This pump is designed for dirty water applications and for continuous use The pump can be operated in either a vertical or horizontal position The pump can only be operated with water inside and should never be run dry Model 2780 features water detection technology After
3. Dirty Water Pump Series INSTRUCTIONS Safety Standards WARNING To reduce the risk of electric shock use only on portable self contained fountains no larger than 5 feet in any dimension WARNING To reduce risk of electric shock connect only to a properly grounded grounding type receptacle CAUTION This pump has been designed for use with water only WARNING Risk of electric shock this pump has not been investigated for use in swimming pool or marine areas WARNING To reduce the risk of electric shock install only on a circuit protected by a ground fault circuit Interrupter GFCI Acceptable for indoor and outdoor use Submersible Pump Make sure the power cable is fully intact before connecting the pump to main power supply Never replace or repair the power cable Replace entire pump if damaged WARNING Make sure the pump is disconnected before performing any maintenance If plug or main electrical socket is wet disconnect the master switch before removing power cable gt Ideally extension cords should not be used If necessary make sure connection is completely sealed and that cable is suitable for external use and identical to that of the P pump cable in terms of insulation and section Avoid lifting the pump by means of the power cable during installation and maintenance operations The pump can be used in liquids with temperatures no greater
4. ges to and from the Lifegard facility Damage incurred by improper repackaging or in shipping is not covered by this warranty Lifegard will only be responsible for repair or replacement of any of its products or parts that are found to be defective and will not bear cost of any incidental or consequential damages arising out of the occurrence of such defect This warranty gives you specific legal rights that vary from state to state oO Replacement Parts Shaft Assembly includes bushings 978 Impeller 978 0 Ring 978 Grid 978 Shaft Assembly includes bushings 1430 2100 0 Ring 1430 2100 2780 Grid 1430 2100 2780 Impeller 1430 Impeller 2100 Shaft Assembly includes bushings 2780 Impeller 2780 LAFEGARD Sess OV AT ISS Phone 800 628 8771 Fax 800 424 1445 Email info lifegardaquatics com Web Site www lifegardaquatics com
Download Pdf Manuals
Related Search