Glacier Bay QK011 Installation Guide
Contents
1. instructions Q Care and Cleaning Your sink is manufactured with the highest grade stainless steel and will provide you many years of enjoyment with the proper care Do After use always rinse your sink with tap water to dilute and remove deposits Towel dry the sink after use whenever possible to prevent water spots Should water spots occur clean with a mild solution of vinegar and water followed by a thorough rinse Use liquid soap a general household cleaner or a weak solution of vinegar and water for regular cleaning Only use plastic scouring pads recommended for use in stainless steel sinks and only use them in the bowl of the sink Scrub in the direction of the satin finish lines Do Not Do not allow any food detergent soap or grease to dry or sit for extended periods of time on the surface of the sink Never use abrasive cleaning products as they will dull and scratch the finish Do not use scouring pads on the deck as they will dull the mirror finish Never use steel wool pads as they will leave iron particles on the sink which will cause corrosion Never leave mild steel or cast iron pans on your sink for extended periods of time as this can cause corrosion 11 HOMEDEPOT COM Please contact 1 877 527 0313 for further assistance Service Parts STAINLESS STEEL OFFSET DUAL BOWL SINK If yo2. Item QK011 G L AC R BR AY Model 7SFI031STS USE AND CARE GUIDE STAINLESS STEEL OFFSET DUAL BOWL SINK Questions problems missing parts Before returning to the store call Glacier Bay Customer Service 8 a m 6 p m EST Monday Friday 1 877 527 0313 HOMEDEPOT COM THANK YOU We appreciate the trust and confidence you have placed in Glacier Bay through the purchase of this stainless steel offset dual bowl sink We strive to continually create quality products designed to enhance your home Visit us online to see our full line of products available for your home improvement needs Thank you for choosing Glacier Bay Table of Contents Table of Contents 000 e cece eee eee eee 2 Parts Required cc ec cece eee e cece ee eeeeeees 4 Safety Information 000 ccc eee e eee ee eee eeeeeeee 2 Package Contents c0cc cece ene e ee eeneees 5 Waranty lt 0caccetsctdeaves eet Svekeea does ede eoes 3 Installation 22 0 22070284022 t628eecereteeaae nt aaae 6 One Year Manufacturer Defect Warranty 3 Undermount lt s ccc recede eee e eee need tiesinis 6 Warranty Claim Procedure 2 000eeeeeeee 3 TOPMOUM ie isikia a a nme meee 9 Pre Installation 0cc cece cece nese eee eens 4 Garbage Disposer Optional 000008 11 Planning Installati n sisisisicinicisinisioisisiniak 4 Care and Cleaning cccceeceeee een onn tp
3. ack from the cutout opening by 1 3 8 in 35 mm Using an electric drill with a 3 8 in 10 mm drill bit drill each hole so that it is 3 8 in 10 mm in diameter and 5 8 in 15 8 mm deep 4 Testing the fit of the sink Place the sink A underneath the cutout in the counter to test its fit Ensure that the reveal is equal on all four sides when viewed from above Make adjustments to the cutout if necessary When you are satisfied with the location of the sink A mark the location of the edge of the counter cutout on at least two sides of the lip of the sink t 7 HOMEDEPOT COM Please contact 1 877 527 0313 for further assistance Installation Undermount continued 9 Installing the flangeless strainer 6 Installing the sink A NOTE If you are installing a garbage disposer not supplied do not install the strainer See Installation Garbage Disposer on page 11 NOTE Install the faucet and soap dispenser not included according to the manufacturer s instructions before this step Apply a small amount of plumber s putty not included in the notch around the drain hole of the sink A Connect the upper strainer body D and the strainer ring E and insert them into the drain hole from the top of the sink A Connect the strainer gasket F and lower strainer
4. act 1 877 527 0313 for further assistance Installation Undermount 1 Creating the template 2 Cutting the counter A NOTE Undermount sinks are mounted from below the counter If you are installing a topmount or drop in sink please see Installation Topmount on page 9 A NOTE It is highly recommended that undermounting be performed by a professional installer Improper installation will void the warranty Using a carpenter s square draw a line 5 from front to back on the bottom of the counter to indicate the location of the center of the sink Draw a line 2 parallel to the front edge of the counter to indicate how far back the sink should be located from the front of the counter 7 Typical setback is 3 1 2 4 in 89 102 mm from the front of the counter depending on the cabinet structure the counter overhang the type of sink bowl and the deck size On a piece of cardboard or paper draw a rectangle of the same size as the hole that you will cut out to accommodate the sink As this sink is 33 in x 22 in 838 mm x 559 mm we recommend that you use a template size of 30 7 8 in x 19 7 8 in 784 mm x 505 mm with square corners A NOTE The flat mating surface of the sink that will touch the underside of your counter is 1 1 16 in 27 mm wide on all four sides Mark the center point 6 of the si
5. al or consequential damages Costs relating to obtaining access for repair or replacement are the responsibility of the user This warranty does not extend to commercial and institutional installation or use WARRANTY CLAIM PROCEDURE If a claimable defect occurs please contact our customer service team at 1 877 527 0313 8 a m 6 p m EST Monday Friday Before you make your claim call please ensure you have Description of the sink Proof of sale Details regarding the defect Name s and address es of the owner and installer Claims must be filled out in writing and returned within six 6 months of the appearance of a defect Failure to comply with this stipulation will make this warranty null and void We reserve the right to a thirty day 30 delay following the receipt of a claim in which to inspect the product We assume no responsibility for labour costs removing or replacing a previously installed product transportation or the return of a product 3 HOMEDEPOT COM Please contact 1 877 527 0313 for further assistance Pre Installation PLANNING INSTALLATION A CAUTION Always wear safety goggles and gloves during installation to prevent personal injury Inspect your unit before proceeding Check the surface for any flaws or damage including dents bends bumps or scuff marks If any damage is noticed do not proceed with installation Report any damage immediately You
6. body G and insert them into the drain hole from underneath the sink A Insert the strainer screw C through the entire assembly from the upper strainer body D to the lower strainer body G Tighten with a Phillips screwdriver Connect the plastic flange 1 and tail pipe 2 and thread the connecting nut 3 through the tail pipe and flange up to the lower strainer body G Lock the connecting nut by hand NOTE The plastic flange 1 tail pipe 2 and connecting nut 3 are not supplied Put the threaded inserts on the bolts of the undermount Clips I loosely in the holes that you drilled for them in the underside of the counter Ensure that the clamps of the undermount clips I are turned so that they do not interfere with the placement of the sink A Place a small bead of silicone sealant not included around the upper lip of the sink A Carefully place the sink A into its location under the counter lining up the pencil marks on the lip of the sink that you made when you tested the fit of the sink Carefully rotate the clamps of the undermount clips I over the clamp bar of the sink A and gently tighten the bolts of the undermount clips I working from side to side to fasten the sink A firmly Recheck the alignment visually from above Wipe away any excess silicone and for best results allow the bond to rest
7. eel surface Improper installation not in accordance with the manufacturer s instructions Dents bumps and scratches incurred during shipping handling or installation Damage caused by failure to follow care and cleaning guidelines Alterations made to the unit by the purchaser or installer Damage caused by accidental impact fire flood freezing or normal wear Bends and warping caused by forced connections over tightened fittings and inadequate support during installation A thorough inspection must be made before installation and any damage must be promptly reported We will not be liable for failures or damage that could have been discovered or avoided by proper inspection and testing prior to installation Incidental repairs that would involve a minimum of time and effort on behalf of the purchaser will not be considered warranty work and no compensation will be deemed forthcoming This warranty is non transferable and shall be voided if the unit is removed from its initial installation or if it is not installed following the manufacturer s instructions Under no circumstance shall we be held liable for personal injury or property damage resulting from improper installation or use of this product We will not be held liable for inconvenience caused by loss of use of this product costs incurred for labour or materials removal and installation of replacement units or any other incident
8. ing during cutting Insert the sink A into the cutout in the counter to test the fit Make adjustments to the cutout if necessary HOMEDEPOT COM Please contact 1 877 527 0313 for further assistance Installation Topmount continued 3 Installing the flangeless strainer A NOTE If you are installing a garbage disposer not supplied do not install the strainer See Installation Garbage Disposer on page 11 Apply a small amount of plumber s putty not included in the notch around the drain hole of the sink A Connect the upper strainer body D and the strainer ring E and insert them into the drain hole from the top of the sink A Connect the strainer gasket F and lower strainer body G and insert them into the drain hole from underneath the sink A Insert the strainer screw C through the entire assembly from the upper strainer body D to the lower strainer body G Tighten with a Phillips screwdriver Connect the plastic flange 1 and tail pipe 2 and thread the connecting nut 3 through the tail pipe and flange up to the lower strainer body G Lock the connecting nut by hand A NOTE The plastic flange 1 tail pipe 2 and connecting nut 3 are not supplied 4 Installing the sink A NOTE Install the faucet and soap dispenser not included according to the manufacturer s instructions before this ste
9. may choose to install this sink either undermount from below the counter or topmount from above the counter You must install this sink only in a counter at least 36 in 914 mm wide with a solid surface that has a minimum thickness of at least 3 4 in 19 mm With undermount installation there should also be a 1 in 25 4 mm build up around the sink Requirements vary for installation in a granite marble stone or butcher block counter so please contact your fabricator for specific details Protect the entire surface of the product during installation to prevent damage TOOLS REQUIRED Measuring tape Carpenter s square Wrenches 2 Pencil Electric drill with 3 8 in 10 mm Saber saw drill bit and 1 in Phillips or Jig saw 25 4 mm or screwdriver 3 in 76 2 mm hole saw Teflon tape 3 Plumber s putty o Silicone sealant CAL Safety goggles PARTS REQUIRED A NOTE Parts not shown to actual size Plastic flange 2 Tail pipe 2 C gt Connecting nut 2 Pre Installation continued PACKAGE CONTENTS Part mnm ojoj wo gt Description Stainless steel sink Flangeless strainer basket Strainer screw Upper strainer body Strainer ring Strainer gasket Quantity 1 2 2 2 2 2 Part Description Lower strainer body Topmount clips Undermount clips Garbage disposer adaptor Rubber ring Quantity 2 10 10 1 1 HOMEDEPOT COM Please cont
10. nk on the template Cut the template out of the piece of cardboard or paper 30 7 8 in 784 mm 19 7 8 in 505 mm 3 1 2 4 in 89 102 mm A CAUTION Always wear safety goggles and gloves when using power tools to prevent personal injury Place the template 8 on the counter with its front 2 parallel to the front of the counter 7 Ensure that it is placed so that the sink will clear all objects and the mounting hardware can be installed Make sure there is a minimum of 3 in 79 2 mm of space underneath on all four sides for the undermount clips l Stick a line of tape 9 around the template and trace the template onto the tape with a pencil Double check the location of the cut line before removing the template Use a saber saw or jig saw to cut along the cut line Place a support underneath the cut out portion of the counter to prevent it from falling during cutting LES 2 a Installation Undermount continued Drilling the holes for the undermount clips CAUTION Always wear safety goggles and gloves when using power tools to prevent personal injury On the underside of the counter mark the location of the ten holes 5 for the undermount clips I These holes should be equally spaced around the perimeter of the cutout with three each on sides 2 and 4 and two each on sides 1 and 3 They should be set b
11. p Apply silicone sealant not included around the underside of the lip of the sink A on all four sides Carefully lower the sink A into the counter ensuring that the factory installed topmount clips H do not catch on the counter edges Slide each topmount clip H along the rails so that they are evenly spaced around the sink A Swing the clamps on the topmount clips H and tighten the screws progressively until the sink rim is flush with the counter Check the alignment as you tighten so that the front of the sink A is parallel to the front of the counter Adjust and re tighten if necessary Do not over tighten ee 7 S 777 Z ZZ 3 5 1 Wipe away the excess sealant with a rag Tightening sequence for clips Installation Garbage Disposer optional 1 Installing the garbage disposer NOTE If you are installing a garbage disposer not supplied do not install a strainer in the sink J w A NOTE The garbage disposer adaptor is designed to fit the flange of the nsinkerator brand of garbage disposers A lee To install a garbage disposer place the rubber ring K around the underside lip of the adaptor J Insert the adaptor J into the drain hole of the sink A Install the garbage disposer to the adaptor J according to the garbage disposer manufacturer s installation
12. tani 11 Tools REGUE secs ccvachcton acca snacnanach avaisanknnada a adsentneians 4 Service Parts 0 0c ccc cee eee eee eee tence 12 Safety Information 1 Your installation must comply with all local plumbing building codes Have a qualified tradesman do or approve your plumbing CAUTION Always weal safety goggles and gloves during installation installation to prevent personal injury 2 Please carefully read this guide before installing or using this product Store this guide in a safe place so you will know where it is when you want to refer to it Warranty ONE YEAR MANUFACTURER DEFECT WARRANTY This stainless steel offset dual bowl sink is warranted to the original purchaser to be free of defects in material and workmanship for one 1 year from the date of purchase Our obligation shall be limited to the repair or replacement of a unit at our discretion that may prove by our sole examination to be defective under normal use and service during the warranty period We may issue credit in the amount of the invoice value of the defective product or a percentage of it according to use in lieu of repair or replacement Any failure of this product that is not traceable to a defect in material or workmanship is not covered by this warranty These non warrantable items include but are not limited to Change in colour or finish due to chemical usage Damage due to the use of steel wool on the stainless st
13. u are missing parts or if you require replacement parts please call our customer service team at 1 877 527 0313 8 a m 6 p m EST Monday Friday Identify the required part s and have the part number s ready Q SS m T Q O Part Description Part number Quantity A Flangeless strainer basket QH0084 2 B Strainer ring QH0085 2 C Strainer gasket QHO0086 2 D Strainer body includes upper and lower body QH0087 2 E Topmount clips QH0088 10 F Undermount clips QH0089 10 G Garbage disposer adaptor and rubber ring QH0090 1 12 GLACIER BAY Questions problems missing parts Before returning to the store call Glacier Bay Customer Service 8 a m 6 p m EST Monday Friday 1 877 527 0313 HOMEDEPOT COM Retain this manual for future use
14. undisturbed for 8 hours or overnight Install the counter as directed by the manufacturer and install all other plumbing as required 3 5 1 Tightening sequence for clips Installation Topmount 1 Creating the template 2 Cutting the counter NOTE Topmount sinks are dropped into the counter from A above If you are installing an undermount sink please see Installation Undermount on page 6 Place the sink A upside down on the counter Center the sink A on the counter so that it is parallel to the front of the counter ensuring that it will not interfere with the inside structure of the cabinet or the counter It must clear the overhang of the counter and the front inside face of the cabinet Trace the outline of the sink A with a pencil Draw a new line 2 3 8 in 9 5 mm inside the first line 1 This will be the cut line As this sink is 33 in x 22 in 838 mm x 559 mm the cut line should be 32 1 4 in x 21 1 4 in 819 mm x 540 mm a A CAUTION Always wear safety goggles and gloves when using power tools to prevent personal injury Y Using an electric drill with a 1 in 25 4 mm hole saw carefully drill four holes 3 inside the cut line 2 Use a saber saw or jig saw to cut along the cut line 2 Place a support underneath the cut out portion of the counter to prevent it from fall
Download Pdf Manuals
Related Search