Glacier Bay HDGFFS4 Use and Care Manual
Contents
1. 02 20 15 Rev 01 201 84019962. that may contain filterable cysts While testing was performed under standard laboratory conditions actual performance of the system may vary based on local water conditions Some or all of the contaminants reduced by this unit may not be in your water supply See Installation and Operation Manual for further instructions on filter cartridge replacement system installation operating procedures and warranty The maintenance instructions must be followed for the product to perform as indicated below Performance Claims Required NSF Max Influent Permissible Level Eff Level Contaminant mg L mg L Cyst gt 50000 mL 99 95 Substance Chlorine Taste and Odor 2 0 10 50 Particulate Class I 0 5 to lt 1 micron gt 10 000 85 Average Avg Max Effluent Avg Min EPA Level Percent MCL mg L Removal mg L 125 000 mL lt 1 lt 1 mL 99 99 99 99 None 0 22 0 47 89 77 None 14 000 000 4 1692 2400 99 9 99 9 Nonet EPA MCL means Environmental Protection Agency Maximum Contaminant Level as required under the Safe Drinking Water Act gt mg L means Milligrams Per Liter which is equivalent to parts per million PPM 3 NSF minimum percent reduction requirement Acceptance level for this substance is based on percent reduction rather than maximum effluent concentration i mL means particles per milliliter Test performed using live Crytospordium Parvum oocyst General Information This filter impro
3. STALLATION LOCATION Install the water filtration system on the cold water supply pipe under the kitchen and or bathroom sink to filter the cold water Refer to the following drawing Be sure to allow a minimum space of 1 1 2 in under the system for removing the filter cartridge to change it filtered water Melted T faucet Te Vin 3 8 in tubing ai Is from cold 3 8 in tubing water C to faucet OUTLET INLET blue collar on HOT T COLD yellow collar on push in fitting ed push in fitting shutoff valve NOTE Be sure to allow a minimum space of 1 1 2 in under the system for removing the filter cartridge to change it SPECIFICATIONS Supply Water Pressure Min Max 30 100 psi 207 689 kPa Supply Water Temperature Min Max 40 100 F 4 38 C Rated Service Flow 60 psi 414 kPa 2 0 gallons per minute 7 57 liters per minute Inlet Outlet 3 8 in quick connect fittings and tubing included 3 HOMEDEPOT COM GLACIERBAY Please contact 1 800 247 1087 for further assistance Pre Installation continued DIMENSIONS 14 3 8 in TOOLS REQUIRED N W lt gt Phillips CK Pliers Adjustable jaw Tubing ff Sealant y screwdriver wrench cutter A tape PACKAGE CONTENTS m B l Hf c Ap y J Lt as E JS H F G Part Description Part Number Quantity Part Description Part Number Quantity A Head assembly with 1073 25 HA 1 G Tubing insert Parts b
4. US Item 1001 090 292 CAN Item 1000 803 390 F GLACIER BAY S Model sHDarrss USE AND CARE GUIDE BASIC DEFENSE DRINKING WATER FILTRATION SYSTEM System tested and certified by NSF International against NSF ANSI Standards 42 amp 53 See performance data sheet for details Questions problems missing parts Before returning to the store call Glacier Bay Customer Service 7 a m 6 p m CST Monday Friday 1 800 247 1087 HOMEDEPOT COM GLACIERBAY 201 8401440 REV 00 THANK YOU We appreciate the trust and confidence you have placed in Glacier Bay through the purchase of this filtration system We strive to continually create quality products designed to enhance your home Visit us online to see our full line of products available for your home improvement needs Thank you for choosing Glacier Bay Table of Contents Package Content sccsssssssseeseeeeeseeee 4 Installation Safety Information ccesseseeeeeee 2 WaAlrAMty cesecsseeeseeeesteesteesseesteenseeseeees 2 Pre Installation 3 Filter Cartridges Pre Installation Inspection 3 Filter Cartridge Life Installation Location asd Filter Cartridge Replacement Dimensions 4 Troubleshooting s sseceeeeeeesees 8 Specifications 3 Tools Required cecsseeetseeteeeeteseeeeeeeeesees 4 Safety Information WARNING Do not use with water that is microbiologically unsafe or of un
5. accordance with national state and local plumbing codes Local code li dplurab information can be obtained at your local public works department your licensed plumper NOTICE In the state of Massachusetts The Commonwealth of Massachusetts plumbing code 248 CMR shall be adhered to A licensed plumber shall be used for this installation Warranty GLACIER BAY WATER FILTRATION SYSTEMS WARRANTY Glacier Bay Water Filtration Systems are manufactured under the highest standards of quality and workmanship Glacier Bay Water Filtration Systems warrants to the original purchaser that this system will be leak and drip free during normal domestic use for a period of one 1 year from date of purchase If this system should ever develop a leak or drip Glacier Bay Water Filtration Systems will free of charge provide the parts necessary to put the system back in good working condition A replacement for any defective part will be supplied free of charge for installation by the purchaser Defects or damage caused by use of other than authorized parts are not covered by this warranty This warranty shall be effective from date of purchase as shown on purchaser s receipt Glacier Bay Water Filtration Systems shall be installed per the manufacturer s installation instructions and specifications Some states do not allow limitations on how long a warranty lasts so the above limitation may not apply to you This warranty is valid for the origina
6. aced o Sanitize the system Call 1 800 247 1087 o The system is for instructions contaminated Water leaks at the push connect o The tubing is not o Push the tubing all the way into the fittings fittings pushed in all the way Oo Cut the tubing square o The tubing is not cut o Remove the nicked portion and reinsert the square tubing into the fitting The tubing is nicked o Remove the rough portion and reinsert the The outer tubing tubing into the fitting surface is not smooth GLACIER BAY Questions problems missing parts Before returning to the store call Glacier Bay Customer Service 7 a m 6 p m CST Monday Friday 1 800 247 1087 HOMEDEPOT COM GLACIERBAY Retain this manual for future use Manufactured by Ecodyne Water Systems 1890 Woodlane Drive Woodbury MN 55125 Performance Data Sheet Model HDGFFS4 HCGFFS5 Drinking Water Filter IMPORTANT NOTICE Read this Performance Data Sheet and compare the capabilities of this unit with your actual water treatment needs It is recommended that before purchasing a water treatment unit you have your water supply tested to determine your actual water treatment needs This filter system is designed to be used for the reduction of the performance claims listed below Do not use where water is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system Systems certified for cyst reduction may be used on disinfected water
7. ag 1 quick connect 3 8 in fittings B Mounting screw Parts bag 2 H Filter cartridge HDGFFF4 1 HCGFFF5 Cc Water supply Parts bag 2 l Filter cover 1073 25 01 1 adaptor D Union connector Parts bag 1 J Tubing 3 8 in 7208251 1 3 8 in to 3 8 in OD x30 in black E Compression nut Parts bag 1 K Use and Care Guide 201 1 3 8 in not illustrated 8401440 F Plastic ferrule Parts bag 1 3 8 in These items are included in the parts bag Part Number 1042 45 AC Purchase replacement filter cartridges from your local The Home Depot store To order replacement parts call customer service at 1 800 247 1087 7 a m 6 p m CST Monday Friday Installation 1 mj Installing the water supply fittings Close the sink s water shut off valve s or another shut off valve upstream from where you will install the filtration system and open faucets to relieve pressure from the sink s cold water supply line Locate the line connecting the cold water shutoff to the sink faucet Typically this line will be a flexible hose Disconnect the nut 1 that connects this line to the cold water shutoff Use a bucket to catch water that drains from this line Locate one piece of the supplied 3 8 in tubing J and attach the compression nut E ferrule F and tubing insert G Wrap thread sealant tape around the threads of the cold water shut off valve and then attach the tubing J by tightening the com
8. eaks o Open the filtered water faucet and let water run for 10 minutes to rinse the system 7 HOMEDEPOT COM GLACIERBAY Please contact 1 800 247 1087 for further assistance Filter Cartridges FILTER CARTRIDGE LIFE It is recommended to replace the filter cartridge every six months of use There are several variables that determine how long a filter cartridge will last These include 1 How much water you use and 2 How much sediment taste and or odor or other unwanted substance is in the water Use this information as a guide However no matter which type of filter cartridge you are using you will know it is time to replace them when you first notice the return of the unwanted sediment taste and or odor in your water or when the flow diminishes or stops FILTER CARTRIDGE REPLACEMENT NOTE There is no need to shut off the water supply when replacing the filter cartridge 1 Turn the filter cartridge to the left to remove the cartridge from the filter head 2 Dispose of the cartridge 3 Install a new cartridge Turn the cartridge to the right to re attach to the filter head 4 Flush for 10 minutes head Turn filter cartridge to the left to remove from head filter cartridge Turn filter cartridge to the right to attach to head Troubleshooting Problem Possible Cause Solution The taste and odor of the wateris o The filter cartridge o Replace the cartridge unsatisfactory needs to be repl
9. en working with the fittings do the following to connect the tubing o Use a tube cutter to cut the end of the tubing square o Inspect the end about 1in of the tubing to be sure there are no nicks scratches or other rough spots o If needed cut the tubing again o Push tubing through the collet and all the way into the fitting Full engagement is 3 4 in length of tube into the fitting Tubing correctly cut and connected end of tubing round and smooth PN with no cuts nicks or flat spots push in fitting foam plug Remove and discard foam plugs correct full 3 4 in engagement Incorrect partial engagement To Disconnect the Tubing o Push the collet inward and hold with a finger while pulling the tubing out collet depress to remove tubing m pe Installation continued 3 Installing the filter cartridge o Remove the small plastic shipping cap from the open end of the filter cartridge o Install the filter cartridge onto the water filter head assembly Turn the filter cartridge to the right to tighten do not over tighten Also refer to the figure in Step 1 for a more detailed illustration Head 4 Tum on the water check for leaks and rinse the system Open the shutoff valve s that you closed at the beginning of this installation Open the filtered water faucet to purge air from the system When the water runs smooth with no bubbles or spurting close the faucet and check the installation for l
10. known quality without adequate disinfection before or after the system This system is certified for cyst reduction and may be used on disinfected waters that may contain filterable cysts Read all instructions before installing and using your water filtration system Follow all steps exactly to AN correctly install Reading this manual will also help you to get all the benefits from the filtration system This system has been tested according to NSF ANSI CAUTION Do not install the filtration system outside Standard 42 and 53 for the specific performance or in extreme hot or cold temperatures Temperature of claims as verified and substantiated by test data The the water supply to the filtration system must be rated capacity for this system is 2000 gallons 7570 eu pusiande OOgr Conounstallomalighwatst liters at a rated service flow of 2 0 gallons per minute 7 57 liters per minute All plumbing must be completed in accordance with national state and local plumbing codes Local code information can be obtained at your local public works department In Massachusetts plumbing code 248 CMR 3 00 and 10 00 shall be adhered to Consult with NOTICE This filtration system works on water pressures of 30 psi minimum to 100 psi maximum If your house water pressure is over the maximum install a pressure reducing valve in the water supply pipe to the filtration system NOTICE All plumbing codes must be completed in
11. l purchaser only and excludes industrial commercial or business use of the product product misuse and product damage due to installation error whether performed by a contractor service company or yourself Glacier Bay Water Filtration Systems will not be responsible for labor charges or for damage incurred during installation repair or replacement nor for incidental or consequential damages Some states provinces and nations do not allow the exclusion or limitation of incidental or consequential damages so the above exclusions or limitations may not apply to you Glacier Bay Water Filtration Systems will advise you of the procedure to follow in making warranty claims Warranty continued Simply write to Glacier Bay Water Filtration Systems at the address below Explain the defect and include proof of purchase and you name address and telephone number or you can also call us at 1 800 247 1087 U S A Canada Glacier Bay Water Filtration Systems Glacier Bay Water Filtration Systems 2455 Paces Ferry Road N W 900 1 Concorde Gate Atlanta GA 30339 4024 Toronto ON M3C 4H9 Pre Installation PRE INSTALLATION INSPECTION Thoroughly check the water filtration system for possible shipping damage and parts loss Also inspect and note any damage to the shipping carton Remove and discard or recycle all packing materials To avoid loss of small parts we suggest you keep the small parts in the parts bag until you are ready to use them IN
12. pression nut E Tighten to provide a leak tight connection Using thread sealant tape install the water supply adaptor C into the nut 1 on the supply line which you previously disconnected Press the stem of the water supply adaptor C into one end of the union connector D Be sure to push the stem all the way in use thread sealing fee mes tape on threads Bey G aa filtered water faucet OUTLET INLET M wT it p f sink Nis m H use thread T J sealing tape INLET OUTLET G on threads cold water shutoff filtration system 5 HOMEDEPOT COM GLACIERBAY Please contact 1 800 247 1087 for further assistance Installation continued 2 Connecting the tubes IMPORTANT Remove the protective foam plugs before connecting the tubes Discard the foam plugs o Route the unused piece of tubing J between the union connector D and the filter system outlet See the Figure in Step 1 Allow some slack measure and cut to length Cut the ends of the tubing square o Insert tubing J all the way into the union connector D and filter system outlet Pull on the tubing to be sure that it s held firmly in the fittings o Repeat the above 2 steps in this tubing procedure to connect the tube installed on the cold water shutoff to the filter system inlet Tubing Connections All Push In Fitting Locations This system includes push in fittings for quick tubing connections Wh
13. ves the taste and odor and reduces many chemical contaminants in drinking water This system has been tested according to NSF ANSI 42 and 53 for the reduction of the substances listed The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system as specified in NSF ANSI 42 and 53 The testing was performed using spiked tap water at a flow rate of 2 GPM 7 6 L min pH of 7 5 0 5 pressure of 60 PSIG and temperature of 68 5 F Manufactured and warranted by Ecodyne Water Systems 1890 Woodlane Drive Woodbury MN 55125 Installation Requirements 30 100 psig 207 689 kPa 40 100 F 5 38 C 2 0 GPM 7 6 LPM 2000 Gallons 7570 Liters Pressure Range Temperature Range Service Flow Rate Service Life Maintenance Refer to Use and Care Manual for warranty and further details on installation and maintenance Cartridges should be replaced every 2000 gallons or six months whichever comes first For replacement elements call 1 800 247 1087 or contact your nearest The Home Depot s store Replacement filter prices will vary Current pricing replacement filters HDGFFF4 HCGFFSS approximately 20 00 to 40 00 per filter element System Tested and Certified by NSF International against NSFI ANSI Standard 42 for the reduction of chlorine taste and odor and Standard 53 for the reduction of cyst
Download Pdf Manuals
Related Search