Glacier Bay QK004 Installation Guide
Contents
1. A NOTE The plastic flange 1 tail pipe 2 and connecting nut 3 are not supplied N Installation Accessory continued 2 Installing the faucet with spray head assembly A NOTE More than one person may be required to complete this step Thread the hose 16 through the faucet pipe 3 inserting the end with the small fitting 15 first Thread the hose 16 through the faucet body 5 inserting the end with the small fitting 15 first Screw the end of the faucet pipe 3 with the nut onto the faucet body 5 Tighten the screw 4 with the supplied Hex wrench N Hold the end of the hose 16 with the large fitting 1 with one hand and with the other hand hand tighten the spray faucet head 2 clockwise onto the large fitting 1 Push the hose 16 in so that the sprayer faucet head 2 aligns properly with the notches on the faucet pipe 3 Unscrew the retaining ring 13 from the bottom of the faucet body 5 ensuring that the washer 11 and gasket 12 are removed with the retaining ring 13 Install the faucet B through the hole in the sink A by threading the hose 16 through the hole and placing the base of the faucet through the hole From underneath slide the washer 11 gasket 12 and retaining ring 13 over the free end of the hose 16 Slide them up to the exposed threaded section 10 of2. 00ccc eee eee eee 13 TOIS REQUE ctccvrceoeteendecuteesceershewecnas 4 Care and Cleaning ccccceeeeeeeeeeneeeeeeees 13 Parts ROGUINCO atctccetcandct cee eede ten aete ewan ae 4 Service Pafi ieii asasi aeaa SA 14 Package Contents 0000ce cece e nee e een eeee 5 Safety Information 1 Your installation must comply with all local plumbing building codes Have a qualified tradesman do or approve your plumbing AN CAUUONE AES WERN Seky COTELE ENE GOTE installation during installation to prevent personal injury 2 Please carefully read this guide before installing or using this product Store this guide in a safe place so you will know where it is when you want to refer to it Warranty ONE YEAR MANUFACTURER DEFECT WARRANTY This stainless steel single bow sink kit is warranted to the original purchaser to be free of defects in material and workmanship for one 1 year from the date of purchase Our obligation shall be limited to the repair or replacement of a unit at our discretion that may prove by our sole examination to be defective under normal use and service during the warranty period We may issue credit in the amount of the invoice value of the defective product or a percentage of it according to use in lieu of repair or replacement Any failure of this product that is not traceable to a defect in material or workmanship is not covered by this warranty These non warrantable items include but are not
3. CAUTION Always wear safety goggles and gloves when using power tools to prevent personal injury On the underside of the counter mark the location of the ten holes 5 for the undermount clips K These holes should be equally spaced around the perimeter of the cutout with three each on sides 2 and 4 and two each on sides 1 and 3 They should be set back from the cutout opening by 1 3 8 in 35 mm Using an electric drill with a 3 8 in 10 mm drill bit drill each hole so that it is 3 8 in 10 mm in diameter and 5 8 in 15 8 mm deep 4 Testing the fit of the sink Place the sink A underneath the cutout in the counter to test its fit Ensure that the reveal is equal on all four sides when viewed from above Make adjustments to the cutout if necessary When you are satisfied with the location of the sink A mark the location of the edge of the counter cutout on at least two sides of the lip of the sink 7 HOMEDEPOT COM Please contact 1 877 527 0313 for further assistance Installation Undermount continued 5 Installing the sink NOTE Install the strainers faucet and soap dispenser before this step See Installation Accessory on page 10 Put the threaded inserts on the bolts of the undermount Clips K loosely in the holes that you drilled for them in the underside of the counter Ensure that the clamps of the
4. Inspect your unit before proceeding Check the surface for any flaws or damage including dents bends bumps or scuff marks If any damage is noticed do not proceed with installation Report any damage immediately You may choose to install this sink either undermount from below the counter or topmount from above the counter You must install this sink only in a counter at least 36 in 914 mm wide with a solid surface that has a minimum thickness of at least 3 4 in 19 mm With undermount installation there should also be a 1 in 25 4 mm build up around the sink Requirements vary for installation in a granite marble stone or butcher block counter so please contact your fabricator for specific details Protect the entire surface of the product during installation to prevent damage TOOLS REQUIRED Measuring tape Carpenter s square Wrenches 2 Pencil Electric drill with 3 8 in 10 mm Saber saw drill bit and 1 in Pine wrench Phillips or Jig saw 25 4 mm or p screwdriver 3 in 76 2 mm hole saw 3 Plumber s putty Qa Silicone sealant Hacksaw Teflon tape CAL Safety goggles PARTS REQUIRED A NOTE Parts not shown to actual size Plastic flange 1 Tail pipe 1 C gt Connecting nut 1 N Pre Installation continued PACKAGE CONTENTS c Part Description Quantity Part Description Quantity
5. Never use abrasive cleaning products as they will dull and scratch the finish Do not use scouring pads on the deck as they will dull the mirror finish Never use steel wool pads as they will leave iron particles on the sink which will cause corrosion Never leave mild steel or cast iron pans on your sink for extended periods of time as this can cause corrosion 13 HOMEDEPOT COM Please contact 1 877 527 0313 for further assistance Service Parts STAINLESS STEEL SINGLE BOWL SINK KIT If you are missing parts or if you require replacement parts please call our customer service team at 1 877 527 0313 8 a m 6 p m EST Monday Friday Identify the required part s and have the part number s ready E ZY eu Oe eo r Part Description Part number Quantity A Faucet sprayer head QH0058 1 B Faucet handle QH0059 1 C Faucet hose QHO060 1 D Cartridge QH0061 1 E Dispenser pump top and assembly QH0062 1 F Soap dispenser assembly kit QH0063 1 G Flangeless strainer basket QH0064 1 H Strainer ring QH0065 1 Strainer gasket QH0066 1 J Strainer body includes upper and lower body QH0067 1 K Topmount clips QH0068 10 L Undermount clips QHO069 10 M_ Garbage disposer adaptor and rubber ring QH0070 1 GLACIER BAY Questions problems missing parts Before returning to the store call Glacier Bay Customer Service 8 a
6. 3 The top lever of the cartridge 6 will be exposed Unscrew the cap 4 and rings 5 making sure not to damage the threads of the cartridge 6 Pull the cartridge 6 out and replace it with a new 1 3 8 in 35 mm ceramic cartridge Replace the rings 5 and the cap 4 Place the handle body 3 on the cartridge 6 Hand tighten the screw rod 2 back onto the handle body 3 and tighten it with the Hex wrench N Do not over tighten Tighten the lever 1 back on o Slowly open the water feed to the faucet to test Care and Cleaning 3 V pe OU Your sink is manufactured with the highest grade stainless steel and will provide you many years of enjoyment with the proper care Do After use always rinse your sink with tap water to dilute and remove deposits Towel dry the sink after use whenever possible to prevent water spots Should water spots occur clean with a mild solution of vinegar and water followed by a thorough rinse Use liquid soap a general household cleaner or a weak solution of vinegar and water for regular cleaning Only use plastic scouring pads recommended for use in stainless steel sinks and only use them in the bowl of the sink Scrub in the direction of the satin finish lines Do Not Do not allow any food detergent soap or grease to dry or sit for extended periods of time on the surface of the sink
7. and the front inside face of the cabinet Trace the outline of the sink A with a pencil This will be the cut line As this sink is 33 in x 22 in 838 mm x 559 mm the cut line should be 32 1 4 in x 21 1 4 in 819 mm x 540 mm AK Draw a new line 2 3 8 in 9 5 mm inside the first line 1 using power tools to prevent personal injury A CAUTION Always wear safety goggles and gloves when Using an electric drill with a 1 in 25 4 mm hole saw carefully drill four holes 3 inside the cut line Use a saber saw or jig saw to cut along the cut line 2 Place a support underneath the cutout portion of the counter to prevent it from falling during cutting fit Make adjustments to the cutout if necessary HOMEDEPOT COM Please contact 1 877 527 0313 for further assistance Insert the sink A into the cutout in the counter to test the Installation Topmount continued 3 Installing the sink A NOTE Install the strainers faucet and soap dispenser before this step See Installation Accessory on page 10 Apply silicone sealant not included around the underside of the lip of the sink A on all four sides Carefully lower the sink A into the counter ensuring that the factory installed topmount clips J do not catch on the counter edges Slide each t
8. limited to Change in colour or finish due to chemical usage Damage due to the use of steel wool on the stainless steel surface Improper installation not in accordance with the manufacturer s instructions Dents bumps and scratches incurred during shipping handling or installation Damage caused by failure to follow care and cleaning guidelines Alterations made to the unit by the purchaser or installer Damage caused by accidental impact fire flood freezing or normal wear Bends and warping caused by forced connections over tightened fittings and inadequate support during installation A thorough inspection must be made before installation and any damage must be promptly reported We will not be liable for failures or damage that could have been discovered or avoided by proper inspection and testing prior to installation Incidental repairs that would involve a minimum of time and effort on behalf of the purchaser will not be considered warranty work and no compensation will be deemed forthcoming This warranty is non transferable and shall be voided if the unit is removed from its initial installation or if it is not installed following the manufacturer s instructions Under no circumstance shall we be held liable for personal injury or property damage resulting from improper installation or use of this product We will not be held liable for inconvenience caused by loss o
9. m 6 p m EST Monday Friday 1 877 527 0313 HOMEDEPOT COM Retain this manual for future use
10. the faucet Tighten the retaining ring 13 by hand until it is snug Using a wrench or pliers tighten the assembly Gently tighten the two screws on the retaining ring 13 Do not over tighten Attach the end of the hose 16 with the small fitting 15 onto the faucet outlet 14 and hand tighten Using one wrench on the hexagonal nut of the faucet outlet 14 and another on the nut of the hose 16 tighten the two ends together Tightening with just a single wrench may deform the hose nut Install the counterweight 6 on the hose 16 about 30 in 762 mm from the underside of the faucet body 5 This can be adjusted based on your own requirements but this is the normal location The lever 7 and screw rod 8 have been installed before shipment If the handle body 9 becomes loose over time remove the lever 7 and tighten the screw rod 8 with the supplied Hex wrench N 11 HOMEDEPOT COM Please contact 1 877 527 0313 for further assistance Installation Accessory continued Installing the soap dispenser assembly Insert the pump top 1 into the dispenser assembly 2 1 Add one rubber gasket 3 onto the dispenser assembly 2 Insert the dispenser assembly 2 through the pre drilled hole on the top surface of the sink A A aS From the bottom of the sink A insert the other a rubber gasket 3 the bottom gask
11. A Stainless steel sink 1 H Strainer gasket 1 B Faucet with spray head assembly 1 Lower strainer body 1 C Soap dispenser assembly 1 J Topmount clips 10 D Flangeless strainer basket 1 K Undermount clips 10 E Strainer screw 1 L Garbage disposer adaptor 1 F Upper strainer body 1 M Rubber ring 1 G Strainer ring 1 N Hex wrench 1 HOMEDEPOT COM Please contact 1 877 527 0313 for further assistance Installation Undermount 1 Creating the template 2 Cutting the counter A NOTE Undermount sinks are mounted from below the counter If you are installing a topmount or drop in sink please see Installation Topmount on page 9 A NOTE It is highly recommended that undermounting be performed by a professional installer Improper installation will void the warranty Using a carpenter s square draw a line 5 from front to back on the bottom of the counter to indicate the location of the center of the sink Draw a line 2 parallel to the front edge of the counter to indicate how far back the sink should be located from the front of the counter 7 Typical setback is 3 1 2 4 in 89 102 mm from the front of the counter depending on the cabinet structure the counter overhang the type of sink bowl and the deck size On a piece of cardboard or paper draw a rectangle of the same size as the hole that you will cut out to accommodate t
12. Item QK004 G LAC E R BR AY Model 70THO35STS USE AND CARE GUIDE STAINLESS STEEL SINGLE BOWL SINK KIT Questions problems missing parts Before returning to the store call Glacier Bay Customer Service 8 a m 6 p m EST Monday Friday 1 877 527 0313 HOMEDEPOT COM THANK YOU We appreciate the trust and confidence you have placed in Glacier Bay through the purchase of this stainless steel single bow sink kit We strive to continually create quality products designed to enhance your home Visit us online to see our full line of products available for your home improvement needs Thank you for choosing Glacier Bay Table of Contents Table of Contents 000 cece cece e eee eens 2 INStANAHON 2 ccti te dsctetedeetieeecede ene reed ae 6 Safety Information 000 cece eee e eee ees 2 Undermount cccccrccricisccccisisiccriniciierisis 6 Wala rereroeiri retna asa ata ans 3 Topmount a2s dee dis avn ses dos dondvadrearadtearnaaerndnaani 9 One Year Manufacturer Defect Warranty 3 ACCOSSOLY ccc ccccicecce ne eeeeneeteewe seen mines iis 10 Warranty Claim Procedure 000eeeeceeeee 3 Garbage Disposer Optional 12 Pre Installation nn cece cece eee eee eee eens 4 Maintenance 0c cece cece eee ee eee e ee eeaeee 13 Planing Installation eicsdivideidad edad died edendmndendedwndink 4 Cartridge Replacement
13. et 4 and the lock 3 nut 5 through the dispenser assembly 2 Hand 4 SS tighten Screw the soap reservoir 6 onto the dispenser assembly 5 2 to complete the installation u To fill the reservoir 6 lift the pump top 1 straight up to 9 remove it from the dispenser assembly 2 Carefully pour in 6 liquid soap Replace the pump top 1 t 3 NOTE This unit is designed to use household liquid soap only A Using any other soap or chemicals in this unit may damage the e dispenser and void the warranty A a gt Installation Garbage Disposer optional 1 Installing the garbage disposer L 0 A NOTE If you are installing a garbage disposer not supplied do not install a strainer in the sink fA A NOTE The garbage disposer adaptor is designed to fit the A fou flange of the nsinkerator brand of garbage disposers To install a garbage disposer place the rubber ring M around the underside lip of the adaptor L Insert the adaptor L into the drain hole of the sink A Install the garbage disposer to the adaptor L according to the garbage disposer manufacturer s installation instructions Maintenance CARTRIDGE REPLACEMENT Turn off the water supply to the faucet B Remove the lever 1 by hand Loosen the screw rod 2 with the Hex wrench N and pull out the handle body
14. f use of this product costs incurred for labour or materials removal and installation of replacement units or any other incidental or consequential damages Costs relating to obtaining access for repair or replacement are the responsibility of the user This warranty does not extend to commercial and institutional installation or use WARRANTY CLAIM PROCEDURE If a claimable defect occurs please contact our customer service team at 1 877 527 0313 8 a m 6 p m EST Monday Friday Before you make your claim call please ensure you have Description of the sink Proof of sale Details regarding the defect Name s and address es of the owner and installer Claims must be filled out in writing and returned within six 6 months of the appearance of a defect Failure to comply with this stipulation will make this warranty null and void We reserve the right to a thirty day 30 delay following the receipt of a claim in which to inspect the product We assume no responsibility for labour costs removing or replacing a previously installed product transportation or the return of a product 3 HOMEDEPOT COM Please contact 1 877 527 0313 for further assistance Pre Installation PLANNING INSTALLATION A CAUTION Always wear safety goggles and gloves during installation to prevent personal injury NOTE More than one person may be required to complete the installation of this product
15. he sink As this sink is 33 in x 22 in 838 mm x 559 mm we recommend that you use a template size of 30 7 8 in x 19 7 8 in 784 mm x 505 mm with square corners A NOTE The flat mating surface of the sink that will touch the underside of your counter is 1 1 16 in 27 mm on all four sides Mark the center point 6 of the sink on the template Cut the template out of the piece of cardboard or paper 30 7 8 in 784 mm 19 7 8 in 505 mm 3 1 2 4 in 89 102 mm CAUTION Always wear safety goggles and gloves when using power tools to prevent personal injury A Place the template 8 on the counter with its front 2 parallel to the front of the counter 7 Ensure that it is placed so that the sink will clear all objects and the mounting hardware can be installed Make sure there is a minimum of 3 in 79 2 mm of space underneath on all four sides for the undermount clips K Stick a line of tape 9 around the template and trace the template onto the tape with a pencil Double check the location of the cut line before removing the template Use a saber saw or jig saw to cut along the cut line Place a support underneath the cut out portion of the counter to prevent it from falling during cutting LES 2 a Installation Undermount continued Drilling the holes for the undermount clips
16. opmount clip J along the rails so that they are evenly spaced around the sink A Swing the clamps on the topmount clips J and tighten the screws progressively until the sink rim is flush with the counter Check the alignment as you tighten so that the front of the sink A is parallel to the front of the counter Adjust and re tighten if necessary Do not over tighten Wipe away the excess sealant with a rag 1 Tightening sequence for clips Installation Accessory 1 Installing the flangeless strainer A NOTE If you are installing a garbage disposer not supplied do not install the strainer See Installation Garbage Disposer on page 12 Apply a small amount of plumber s putty not included in the notch around the drain hole of the sink A Connect the upper strainer body F and the strainer ring G and insert them into the drain hole from the top of the sink A Connect the strainer gasket H and lower strainer body 1 and insert them into the drain hole from underneath the sink A Insert the strainer screw E through the entire assembly from the upper strainer body F to the lower strainer body I Tighten with a Phillips screwdriver Connect the plastic flange 1 and tail pipe 2 and thread the connecting nut 3 through the tail pipe and flange up to the lower strainer body I Lock the connecting nut by hand
17. undermount clips K are turned so that they do not interfere with the placement of the sink Place a small bead of silicone sealant not included around the upper lip of the sink A Carefully place the sink A into its location under the counter lining up the pencil marks on the lip of the sink that you made when you tested the fit of the sink Carefully rotate the clamps of the undermount clips K over the clamp bar on the sink A and gently tighten the bolts of the undermount clips K working from side to side to fasten the sink A firmly Recheck the alignment visually from above 3 5 1 Tightening sequence for clips Wipe away any excess silicone and for best results allow the bond to rest undisturbed for 8 hours or overnight Install the counter as directed by the manufacturer and install all other plumbing as required Installation Topmount 1 Creating the template 2 Cutting the counter NOTE Topmount sinks are dropped into the counter from above If you are installing an undermount sink please see Installation Undermount on page 6 l Place the sink A upside down on the counter Center the sink A on the counter so that it is parallel to the front of the counter ensuring that it will not interfere with the inside structure of the cabinet or the counter It must clear the overhang of the counter
Download Pdf Manuals
Related Search