Hampton Bay KP1896-NHK Installation Guide
Contents
1. Mount the cabinet to the wall with hardware appropriate for your wall type Once your corner I cabinets have been installed work outward to install the remaining cabinets I Check to level amp ensure square flat to wall Shim if necessary STEP 3 ATTACH CABINETS TOGETHER After the corner cabinet is secured to the wall use C clamps to align the next cabinet to the first cabinet Use a level to be sure the adjoining cabinets are flush and level with each other If needed shim the cabinets to level Drill a 1 8 pilot hole in the face frame above or below each door hinge location Attach the second cabinet to the first cabinet using a 8 x 2 2 screw and countersink for best appearance Always attach cabinets together at the face frame as shown Do not attach through the cabinet side panel ATTENTION You must drill pilot holes to attach cabinets together Installation Shims Not Included Scrap Block 1 8 DIA STEP 4 INSTALL REMAINING CABINETS Drill a 3 16 pilot hole at the stud locations through the back panel and into the stud Level and mount the cabinet to the wall with 10 x 3 screw If needed shim the cabinet to level DO NOT COMPLETELY TIGHTEN MOUNTING SCREWS UNTIL ALL CABINETS HAVE BEEN ATTACHED TOGETHER After all cabinets have been attached together and are level and secure then tighten all mounting screws Take care to seat mounting screws tightly against back rail or panel without driving into back rail or2. panel material Check to be sure that all cabinets remain level after tightening NOTE To attach a wall cabinet to a TALL PANTRY unit drill a 1 8 pilot hole 7 8 deep through the wall cabinet face frame to the tall pantry unit Use a 8 x 1 5 8 screw to secure cabinets together STEP 5 KITCHEN DRAWER ADJUSTMENT After you install all of your cabinets it may be necessary to adjust the drawer fronts so they are level and have the proper reveals To better secure adjustment loosen the screws holding the drawer glides to the frame of the cabinet and adjust the drawer then tighten the screws Drill a 1 8 pilot hole through the second hole below and drive a 8 x 5 8 screw to fix the drawer in place Cabinet drawers and doors should line up as shown below 1 Loosen screw and make vertical adjustments The fastening solutions described here are recommendations only and are based on commonly used installations Each installer must evaluate the specific characteristics of the particular wall on which the cabinets are to be installed to ensure the proper fastening solution is used and the product is fastened safely and securely This may require hardware or fastening methods which are different from or additional to what is described here THE MANUFACTURER DOES NOT WARRANT THE INSTALLATION OF THIS PRODUCT 1 888 578 4009 www hamptonbay com cabinets
3. INSTALLATION INSTRUCTIONS 72 STEP 1 CABINET INSTALLATION SELECT HARDWARE THAT IS BEST SUITED FOR YOUR WALL TYPE IMPORTANT USE PAN HEAD OR ROUND HEAD SCREWS WITH SEAT WASHERS SEAT SCREWS TIGHTLY AGAINST BACK RAIL OR PANEL WITHOUT DRIVING INTO BACK RAIL OR PANEL MATERIAL aR SIs NA SIS SIS fea RJ NI N N NB NR NA NA NA NA N N NN NW N N N N NN NN NN NN NG Ne NR NB aja STUDS secure to wall with 10x DRYWALL Drill holes and secure to the wall with toggle bolts CONCRETE Drill 4 holes 3 screws at stud location Note Use toggle bolts only when cabinet cannot be attached to a wall stud insert 10 wall anchors and secure to Cabinet must also be attached to adjacent cabinet as outlined in Step 3 wall with 10 x 3 screws STEP 2 CABINET INSTALLATION STARTING IN A CORNER Always start in a corner where two runs of cabinets will come together All doors will need to be removed during the installation process to properly align all cabinets together Locate and mark wall studs where planned cabinets are to be installed Place the corner cabinet into that position Use a level to be sure that the cabinet is level and straight If needed shim the cabinet to level IMPORTANT Shim cabinets square flat to the wall so there are no gaps between back of cabinet and wall in the mounting area Drill a 3 16 pilot hole at the stud locations through the back panel and into i Mounting Hardware the stud
Download Pdf Manuals
Related Search