Halsey Taylor 8634088383 Use and Care Manual
Contents
1. 37 A J sero 34 CHILLER INLET CHILLER OUTLET NANA NINNI LISLLLLSLSE L Li DLL SOL gb ab BE gb gb gh g S S Figure 18 OVL II SEREE Q ESREE Q Tube Routing 97882C Rev F 7 09 OVLEREEQ G OVLSREEQ G OVLESREEQ G OVLSEREEQ G TROUBLESHOOTING amp MAINTENANCE Orifice Assembly Mineral deposits on orifice can cause water flow to spurt or not regulate Mineral deposits may be removed from the orifice by poking with a small round file not over 1 8 diameter or using a small diameter wire A CAUTION DONOT file or cut orifice material Stream Regulator If orifice is clean regulate flow as in Step 14 of the installation instructions If replacement is necessary see parts list for correct regulator part number A CAUTION To preserve the quality and keep this AZTEC GOLD finish clean and spot free clean this surface with only mild detergent or window cleaner and polish with a soft cloth DO NOT use any abrasive cleaners or harsh chemicals They WILL damage the finish Sensor Control The sensor has a 2 second delay time If sensor fails to operate valve mechanism or operates erratic2. NOTE Building construction must allow for adequate air flow on both sides top and back of chiller A minimum of 4 102mm on both sides and top is required See chiller installation for additional Figure 13 Upper Panel Installation instructions oe Note With OVL II SEREE Q or OVL II ESREE Q models the standard reach fountain must be mounted at the upper position on panel a gn tit Figure 12 Chiller Installation 3 Attach solenoid valve assembly to the underside of cross member of mounting frame on electronic sensor unit See Fig 7 4 Make water supply connections Inlet port is marked on the chiller 1 4 O D copper tube Bend the copper tube provided at an appropriate length from the chiller to opening Figure 14 Fountain Installation in frame Install the in line strainer provided with chiller by er pushing it in until it reaches a positive stop approximately 8 Connect the fountain drain waste tube to the building 3 4 19mm on the marked chiller inlet port See Figs 17 amp sanitary SEMI system Connection should be made in 18 Attach an unplated and deburred copper water inlet line compliance with local plumbing code requirements Note and a service stop not provided to the chiller Turn on the Plumbing trap is not included with the fountain water supply and flush the line thoroughly 9 Make connection between solenoid valve assembly 5 Make connection between r
3. 0550 Drainnut 2 2 4 4 2427 101637451550 Friction Ring to 2 2 2427 12 100023340560 _ _Waste Tube Gasket 1 1 2 2 2627 14 61313C Regulator W Red Spring 1 1 61314C Regulator W Green Spring 1 22 1 1 NIS N MN 11 NM NM i NO NI N MN C meo eana O a Basin Liner S S i 1 2 2 a 88417001 Screw 8 18x 37 2 2 2 2 n 10 568400 TopPlate Actuator J o 1 1 20 Bottom Plate Actuator i Lo odo 1 ao Extended Reach Arm SS__ 1 1 1 25 277546 ExtendedReachamee ag 1 1 28 27690 Standard Reacharm EE S S 1 _ 28 277550 Standard Reach Arm EE AG Standard Reach Arm S S Lo 1 a Standard Reach Arm A G n 1 g o f a a 978820 Rev F 7 09 2 NM DI 1 r 3 2 2 oe 7 8 9 0 2 2 OVLEREEQ G OVLSREEQ G OVLESREEQ G OVLSEREEQ G Parts List Continued nego sree seneca esneco Fig Item Part No Description EREE Q SREE Q SEREE Q ESREE Q 25 2700C i i 2 22797C Upper Panel OVL II EREE S S 19 27 27886C Upper Panel OVL II EREE A G 1 1927 22799C_ Upper Panel OVL II SREE S S oo oio Soo oo S o o S ay 27888C Upper Panel OVL II SREE A G Ce ae lo e l e 26958C_ UpperPanel OVL ISEREE S S lo Z 1 J 18 24 27 278900 UpperPanel OVLIISEREE AG Soo deaz 22
4. 5 97882C Rev F 7 09 OVLEREEQ G OVLSREEQ G OVLESREEQ G OVLSEREEQ G Models OVL II EREE Q OVL II SREE Q cae cai TA 1 Cut a rectangular wall opening 18 3 4 475 mm W x 37 3 4 H 959 mm and 4 1 2 114 mm above the floor line see Figure 10 The dimensions are required to obtain proper rim and bubbler heights for compliance with ANSI standard A117 1 2 Reinforce the wall opening on all sides to adequately support the water fountain This reinforcement must support up to 150 Ibs static load and provide a means for securing the frame assembly in place ll i NOTE Building construction must allow for adequate air flow on both sides and top of remote chiller unit L Minimum of 4 102 mm is required 3 Install plumbing and electrical rough ins A junction box for a 3 wire 10 amp branch circuit is provided on the inside of the chiller Standard 120 Volts 60 Hz and single phase 4 Remove frame and related hardware from packaging Release the two shelf rods by cutting cable ties MODEL OVL SREE 40 WOOD OR STEEL FRAME SHOWN N I VA PROVIDED n N 18 ELECTRICAL INLET LOCATION ON CHILLER 8 203m TO FLOOR LINE 5 16 SCREWS OR BOLTS 2 10 REQ D NOT PROVIDED Ses N N FRAME MODEL 18 3 4 5 1 8 BACK OF WALL TO 476mm BE 12 305mm OVL EREE TI MIN DEPTH SCREWS OR BOLTS FLOOR LINE NOT PROVIDED HOOK RODS 2 P N 101567443730 INSTALL 2
5. 7950 UpperPanel OVL IESREE S S 1 192427 278920 UpperPanel OVL IESREE AG 1 192427 26833C Lower Panel OVL II EREE SREE S S 1 a 1527 27894C Lower Panel OVL II EREE SREE A G 1 1 15 27 550960 TALE 56092C Poly Tubing 1 4 Cut To Length 56082C Regulator Nut 70016C Hex Nut 10 32 70989C Screw 8 36 x 37 Ground NO POT N a 00 2 2 2 N 9 30 31 2 oO ih ok Ly oe LX LN 3 oe D 39 36 37 38 9 40 4 17 18 W 7 10 26 ID 2 3 4 5 24 di D N O1 27 29 27 gt gt O 7 8 9 N O1 NIN NM N Ol oO Ol N CO N A gt h 26 50 75507C__ Fitting 1 4 NPTF NOTE S S means Stainless Steel A G means Aztec Gold 97882C Rev F 7 09 Nr OVLEREEQ G OVLSREEQ G OVLESREEQ G OVLSEREEQ G Models OVL II SEREE Q OVL II ESREE Q 1 Cut a rectangular wall opening 37 1 2 953 mm W x 37 3 4 H 959 mm and 4 1 2 114 mm above the floor line see Figure 7 The dimensions are required to obtain proper rim and bubbler heights for compliance with ANSI standard A117 1 2 Reinforce the wall opening on all sides to adequately support the water fountain This reinforcement must support up to 150 Ibs static load and provide a means for securing the frame assembly in place NOTE Building construction must allow for adequate air pd flow o
6. OVLEREEQ G OVLSREEQ G OVLESREEQ G OVLSEREEQ G HALSEY TAYLOR OWNERS MANUAL OVL I I Series Electronic Eye Barrier Free Water Coolers Refrigerated Fountains with Back Panel Fig 1 OVL II EREE Q Fig 2 OVL II SREE Q Fig 3 OVL II SEREE Q Fig 4 OVL IIl ESREE Q OVL II EREE Q OVL II Series Extended Reach OVL II SREE Q OVL II Series Standard Reach OVL II SEREE Q OVL II Series Dual Installation OVL II ESREE Q OVL II Series Dual Installation INSTALLER A CAUTION Review these instructions before beginning installation Be sure that installation conforms to all plumbing electrical and other applicable codes A WARNING When installation is complete ensure these instructions are left in the plastic bag provided inside the installed unit for future reference A WARNING Service to be performed by authorized service personnel only NOTE It is common practice to ground electrical hardware such as telephones computers and other devices to available water lines This can however cause electrical feedback in the plumbing circuit which results in an electrolysis effect occurring in the fountain This may result in water which has a metallic taste to it or has a noticeable increase in the metallic content of the water When inspecting plumbing circuit remember the line may be grounded some distance from the installation and may occur outside the building or area in which the unit is being installed T
7. SCREWS P N 111008343890 IN FRAME y CHILLER SHELF BEFORE INSTALLING IN OPENING P N 27638C Figure 10 Rough In Assembly Single Station Mounting Frames 97882C Rev F 7 09 6 OVLEREEQ G OVLSREEQ G OVLESREEQ G OVLSEREEQ G 5 Install the frame squarely in wall opening with frame upright edges flush with the finished wall surface Place shelf inside frame and line up the 2 holes on each Insert loose ends of rods into holes on sides of shelf panel Using appropriately sized screws or bolts not provided fasten the shelf and frame to the bottom of wall opening MODEL OVL EREE ELECTRICAL RECEPTACLE IN SHADED AREA 3 1 8 79mm 11 8 28mm gin xa NI H N N 5 5 8 142mm 3 N M 9 3 8 N 238mm TON WALL LINE Aa 12 305mm MINIMUM att BACK WALL LINE 5 8 458mm 16mm 280mm E mm c T E 2 1 16 VA 52mm HN 34 864mm a7 686mm ADA D REQUIREMENT 7 8 4 1 2 203mm X i 20 1 2 724mm 24 610mm secure the frame sides and top to the wall opening using 10 5 16 bolts or screws not provided NOTE Be sure that frame is squared in location Do not use less than the required screw quantity and size 3 1 8 ELECTRICAL RECEPTACLE N 79mm IN SHADED AREA 1 1 8 28mm B EB At IZ N N 5 5 8 amp 142mm N o H X 9 3 8 N 238mm VV WALL LINE _ 12 305mm MINIMUM DEPTH BACK WALL LINE p 13 5 16 5 8 1 1 2 338mm 16mm 38mm 11 C 279mm E ig Y i sr 2 1 16 W 52
8. ally check the following a Ensure there are no obstructions within a 40 inch radius from the front of fountain b Check wire connections at the solenoid valve and at the sensor CAUTION Make sure unit is unplugged before checking any wiring c Ensure proper operation of solenoid valve If there is an audible clicking sound yet no water flows look for a obstruction in the valve itself or elsewhere in the water supply line WARNING Do not expose sensor to direct sunlight Sensor Range Adjustment The electronic sensor used in this fountain is factory pre set for a visual range of 36 inches If actual range varies greatly from this or a different setting is desired follow the range adjustment procedure below a Remove bottom cover of fountain b Remove sensor by removing washers and nuts that secure sensor on studs c Locate range adjustment screw between the red lenses of the sensor then with a small tip screwdriver rotate the range adjusting screw clockwise to increase range or counter clockwise to decrease range 1 4 turn of screw is equal to approximately 12 18 inches of range CAUTION Complete range of sensor 24 46 inches is only one turn of the adjusting screw d Remount sensor on studs and replace bottom cover Actuation of Quick Connect Water Fittings Cooler is provided with lead free connectors which utilize an o ring water seal To remove tubing from the fitting relieve water pressure push in on
9. emote chiller outlet tube and fountain s Insert the 1 4 poly tubing coming from the and solenoid valve assembly Outlet port is marked on fountain with sensor into the solenoid valve Insert the 1 4 the chiller 1 4 O D copper tube Install a 1 4 union tee poly tubing coming from the fountain with push button into provided on the marked chiller outlet port Insert one end of the tee See Figs 17 amp 18 1 4 poly tubing into the union tee and the other end into the 10 Connect power cord of sensor to solenoid valve by straight fitting on the solenoid valve assy See Figs 17 amp 18 running it through the back panel and connecting it 6 Hang the upper panel on the mounting frame hanger as shown in Fig 26 Connectors may be connected to Align holes in the panel with the holes in the mounting frame either terminal on solenoid valve Attach ground wire to Be sure that panel is engaged with hanger at top of frame solenoid valve bracket with green ground screw before releasing it 97882C Rev F 7 09 OVLEREEQ G OVLSREEQ G OVLESREEQ G OVLSEREEQ G Turn on water supply and check for leaks Release air from tank by interrupting infrared beam a steady stream of water assures all air is removed The sensor has a 30 second maximum ON time It may be necessary to step away from beam a few times to allow chiller tank to fill A CAUTION DONOT SOLDER tubes while inserted into the strainer as damage to o rings may res
10. eviously loosened screws securely Replace bottom access panel to fountain basin using screws provided Tighten securely C ee ee a _ _ _ _ Parii eo rn merr rr tremo ry r p a p _ __ _ aoe baa oe oo 2 _ _ m6 Se e __ _ _ _ n Tr _ _ rei eee ee _ a m Pae a ee Parn _ _ _ P _ a rn Lee rr ee Tee p _ __n m eee ee ee m n r m _ _ _ a ee SS Se e_ a r e_ _ TL a ee Figure 15 Lower Panel Installation Ae a 1 2 38mm Figure 16 Stream Height 37 TO BUBBLER 8 37 ae Tau pium CHILLER OUTLET ci E Figure 17 OVL II EREE Q SREE Q Tube Routing 37 TO BUBBLER
11. his condition can be avoided in most cases by using recommended materials during installation Any drain fittings provided by the installer should be made of plastic which will electronically isolate the fountain from the remainder of the building s plumbing circuits 97882C Rev F 7 09 OVLEREEQ G OVLSREEQ G OVLESREEQ G OVLSEREEQ G Installation Package 1 4 O D TUBE 3 8 O D UNPLATED l l l WATER INLET COPPER TUBE CONNECT BUILDING WATER The components for installation are packed in three TO COOLER COLD WATER SUPPLY INLET separate boxes regardless of the type of unit being installed The boxes contain the following d i Box No 1 Wall Frame s Box No 2 Remote Chiller SJ8 Q NOTE WATER FLOW SERVICE STOP Box No 3 Fountain s Arm s and Panels DIRECTION NOT FURNISHED Additional materials as noted in the Parts List are also Parts List Number Required OVL II OVL II OVL II OVL II tom panno eseriston eReEa saeco eee esaeco Fig 260900 Bottom Cover Standard Reach 1 1 2 2 Push Arm Actuator 1 20 Push Arm Actuator AG fe 2 20 sso Bubber ss SCPC Tt a aa 453960 Bubble AG __ 2 o a Bubbler EasyFlex option 1 2 Strainer Plate A G it 1 2 2 ax 101570540560 DrainGasket 1 1 2 2 2427 2 4 l NM MIAININ NM NM MN 7 515750 Packing Ring ta o 2 2 2427 11034622
12. lush with the finished wall face Secure the frame to the wall through holes with 12 5 16 bolts or screws not provided Tighten securely NOTE Be sure that frame is squared in location Do not use less than required screw quantity and size Attach the chiller shelf support rods to the right side of the frame uprights at the second set of holes counting from the bottom and to the shelf at the 2 side holes Line up the other shelf holes with the frame bottom holes and fasten the assembly to the wall opening using appropriately sized screws or bolts and nuts not provided MODEL OVL SEREE SHOWN 3 1 8 79mm 1 1 8 MODEL i OVL ESREE oe ELECTRICAL RECEPTACLE IN SHADED AREA p b A 18 3 4 5 476mm B IV N N 5 5 8 4 N 9 3 8 X 238mm SSS WALL LINE 12 305mm 49 MINIMUM 458mm DEPTH BACK WALL LINE 13 5 16 5 8 338mm 16mm 11 5 C a 279mm pz Y A i X mi 4 21 16 T 52mm aa a LEY 40 _ 1E iN Au 34 1 2 34 877mm 864mm 27 am E 28 A gu mm ADA 24 RQUIREMENT D Slom 8 exe 4 1 2 203mm FINISHED FLOOR 114mm 1 25mm 44 279mm Legend Item Description A 1 4 O D Tube Water Outlet Connection B 3 8 O D Tube Water Inlet Connection C 1 1 4 O D Waste Tube D Electrical Inlet on Chiller E Electrical Outlet Location Additional UL CSA listed grounded outlet By others required for 115 Volt 60Hz Figure 8 OVL Il SEREE Q OVL II ESREE Q Rough In Dimensions
13. mm 178mm a ee b i ane N P 40 34 1 2 1016mm E 377mm 24 D 610mm 2 8 41 2 203mm X FINISHED FLOOR 114mm FINISHED FLOOR 114mm 25mm Jemm 11 11 279mm 279mm Legend Item Description A 1 4 O D Tube Water Outlet Connection 3 8 O D Tube Water Inlet Connection 1 1 4 O D Waste Tube Electrical Inlet on Chiller Electrical Outlet Location Additional UL CSA listed grounded outlet By others required for 115 Volt 60Hz mO W Figure 11 OVL II EREE Q OVL II SREE Q Rough In Dimensions 97882C Rev F 7 09 7 OVLEREEQ G OVLSREEQ G OVLESREEQ G OVLSEREEQ G REQUIRED TOOLS AND MATERIALS 7 Install fountain Remove bottom access panel on underside of fountains and SAVE the screws Mount These tables show special tools and or additional materials not the fountains to the upper panel and frame with provided which are necessary to complete installation of these 4 5 16 x 3 4 19mm long bolts and nuts provided Tighten securely units Special Tools item Description Quant Additional Materials fem Description Quantity Unpiated copper inlet pipe OVL II EREE Q SREE Q SEREE Q ESREE Q INSTALLATION 1 Assemble and place frame in wall as shown on preceding pages 2 Install chiller Remove front panel of chiller Remove and discard cardboard inner pack from between compressor and side panel Slide chiller onto the shelf and position it to the left on the shelf
14. n both sides and top of remote chiller unit a minimum of 4 102 mm is required i 3 Install plumbing and electrical rough ins A junction box for a 3 wire 10 amp branch circuit is provided on the inside of the chiller Standard 120 Volts 60 Hz and single phase 4 Remove frames and related hardware from packaging Release the two shelf rods by cutting cable ties Attach the x two frames together through the upright supports with 4 5 16 x 3 4 19 mm long bolts and nuts provided Tighten securely REVERSED CONFIGURATION HIGHER UNIT ON THE RIGHT WOOD OR STEEL FRAME 37 3 4 SHOWN NOT PROVIDED 959mm ELECTRICAL INLET LOCATION ON CHILLER 5 16 SCREWS OR BOLTS 12 REQ D NOT FURNISHED 4 1 2 FRAME 14mm mm TO FLOOR LINE 5 16 HEX NUT 4 REQ D PROVIDED P N 111577343890 37 1 2 lt lt a 953mm NS SCREWS OR BOLTS NUT PROVIDED LA BACK OF WALL TO BE 12 HOOK RODS 2 130mm 305mm MIN P N 101567443730 ROGER LINE DEPTH INSTALL 3 SCREWS P N 111008343890 IN FRAME BEFORE INSTALLING IN OPENING BOLT FRAMES TOGETHER WITH 5 16 x 3 4 19mm BOLTS 4 REQ D PROVIDED STANDARD CONFIGURATION P N 111577243890 HIGHER UNIT ON THE LEFT Figure 7 Rough In Assembly Dual Station Mounting Frames 97882C Rev F 7 09 OVLEREEQ G OVLSREEQ G OVLESREEQ G OVLSEREEQ G Install the frame assembly squarely in wall opening with frame upright support edges f
15. the gray collar while pulling on the tubing See Figure 19 To insert tubing push tube straight into fitting until it reaches a positive stop approximately 3 4 OPERATION OF QUICK CONNECT FITTINGS SIMPLY PUSH IN TUBE IS SECURED N COLLET TUBE TO ATTACH IN POSITION EASE TUBE PUSHING TUBE IN BEFORE PULLING IT OUT HELPS TO RELEASE TUBE Figure 19 Quick Connect Fittings 97882C Rev F 7 09 10 Stream Height Figure 20 Push Arm Mechanism Adjustment 25 24 Figure 21 Regulator Mounting Mechanism Ale Regulator Mounting Bracket Figure 22 Regulator Assembly OVLEREEQ G OVLSREEQ G OVLESREEQ G OVLSEREEQ G See Fig 22 3 4 16 17 See Fig 20 22 Figure 24 Push Bar Fountain Assembly Side View 97882C Rev F 7 09 11 OVLEREEQ G OVLSREEQ G OVLESREEQ G OVLSEREEQ G Connect To Sensor Assy Figure 25 View of Electronic Sensor Figure 26 View of Solenoid Valve Figure 27 Electronic Sensor Fountain Assembly Side View 2222 CAMDEN COURT OAK BROOK IL 60523 630 574 3500 REPAIR SERVICE INFORMATION TOLL FREE NUMBER 1 800 260 6640 eer FOR PARTS CONTACT YOUR LOCAL DISTRIBUTOR OR VISIT OUR WEBSITE WWW HALSEYTAYLOR COM 97882C Rev F 7 09 12
16. ult 12 These products are designed to operate on 20 105 PSIG supply line pressure If inlet pressure is above 105 PSIG a pressure regulator must be installed in the supply line A CAUTION Any damage caused by connecting 13 14 these products to a supply line with pressure lower than 20 PSIG or higher than 105 PSIG IS NOT covered under warranty Make electrical connections to the chiller See chiller instructions Check stream height from bubbler Stream height is factory set at 35 40 PSI If supply pressure varies greatly from this please do the following For Pushbar units only remove items 2 19 and 20 push arm and the bottom and the top actuator plates Figure 20 by removing the screws holding assembly together and adjust the screw on the regulator Item 14 Figs 21 amp 22 Clockwise adjustment will raise stream height and counterclockwise movement will lower stream height For Electronic sensor units only remove bottom access panel and turn adjustment screw on the regulator Item 14 Figs 25 amp 27 Clockwise adjustment will raise stream height and counterclockwise movement will lower stream height For best adjustment stream height should be approximately 1 1 2 88mm above the bubbler guard See Figure 16 Mount lower panel Loosen the two 2 10 24 x 5 8 16mm screws at frame bottom lip Slide upper tongue of lower panel under lower edge of already installed upper panel Tighten pr
Download Pdf Manuals
Related Search