KOHLER K-7104-CP Installation Guide
Contents
1. INSTALLATION BATH DRAIN THEBOLDLOCK OF KOHLER 89671 2 AB RECOMMENDED TOOLS AND MATERIALS gt toe i AM gt Wrench as Screwdrivers Plumbers Pipe Putty Pliers Wrench BEFORE YOU BEGIN e Observe local plumbing e Kohler Co reserves the right codes to make revisions in the design e Install the drain to the of faucets without notice as bath before installing the specified in the Price Book bath ROUGHING IN DIMENSIONS id mae 15 3 4 7 L l 5 J 12 7 8 3 1 1 2 O D 1 1 2 N PS 89671 2 AB 2 Kohler Co Kohler WI 2 INSTALL DRAIN Apply a ring of plumbers putty Apply or other sealant around the Plumbers underside of the strainer Putty according to the putty Strainer manufacturer s instructions Position the gasket between the drain ell and the bottom of the bath Begin threading the Gasket Bath strainer into the drain ell SE Drain Ell TT Position the drain ell tube to face the front of the bath Insert the handle of a pliers into the top of the strainer so the handle contacts the drain ell bosses Securely tighten the strainer to the drain ell Remove any excess sealant Attach the gasket to the overflow ell as shown Make sure the tapered end of the Gasket Ouarilon Ell gasket is facing up sil Align the overflow ell with the overflow hole in the bath Kohler Co Kohler WI2. 3 89671 2 AB From inside the bath securely tighten the retainer nut to the overflow ell Assemble the coupling nuts and O rings onto the overflow and drain ell tubes Position the tee according to the illustration for your installation Insert the overflow and drain ell tubes completely into the tee Align and tighten the coupling nuts Apply thread sealant to the tailpiece threads and thread the tailpiece into the tee Retainer Nut y Overflow Tube Coupling Drain Nut Ell ee 2 8 SI B Ring 27 E O i eli 7 Ring i Coupling Tailpiece Nut Through Above Floor Floor INSTALL THE BATH AT THIS TIME BE SURE TO FOLLOW ALL INSTRUCTIONS PACKED WITH THE BATH 89671 2 AB 4 Kohler Co Kohler WI Make sure the drain tailpiece fits properly into the trap You may need to cut the tailpiece for proper fit Between 1 and 2 of the tailpiece should fit inside the trap Adjust the lift assembly linkage Turnbuckle by rotating the turnbuckle and 3 secure by tightening the rece locknut N Locknut Insert the lift assembly into the overflow Tighten the overflow hood to the overflow ell with the screws provided Kohler Co Kohler WI 5 89671 2 AB Assemble the lever to the overflow hood with screw Turn the lever to the closed position Insert the stopper assembly into the bath drain hole The stopper should rise about 3 8 above the strainer in the open position To a
3. djust the height remove the stopper assembly and loosen the nut below the stopper Raise the stopper by turning it counterclockwise lower by turning clockwise Retighten the nut If you cannot obtain sufficient clearance by adjusting the stopper remove the lift rod assembly and loosen the locknut Rotate the turnbuckle counterclockwise to lengthen the lift rod clockwise to shorten the lift rod Secure with the locknut and reinstall the lift rod assembly 89671 2 AB Lift Rod i Locknut Turnbuckle _ Kohler Co Kohler WI Kohler Co Kohler WI 7 89671 2 AB CALL US FOR HELP Questions Problems First review the installation instructions to ensure correct installation For additional assistance in the USA call our Customer Service Department for direct help You may also contact us at our web site listed below 1 800 4 KOHLER THEBOLDLOCK OF KOHLER www kohlerco com Kohler Co Kohler WI 2000 Kohler Co 89671 2 AB
Download Pdf Manuals
Related Search