MUSTEE 10CBT Instructions / Assembly
Contents
1. required Screw stud in place until nut makes contact with bottom of lug continue 1 4 tum maximum Repeat this operation for each mounting lug See TYPICAL STUD INSTALLATION FU LR Y 1m WAS t 4 TETA AAAA nnn TYPICAL STUD INSTALLATION m Apply a bead of clear siliconized sealant not furnished all around the underside of the rim See Detail Drawing Place Countertop Sink into the countertop cutout secure from the underside with hardware provided You will need a 7 16 socket or wrench to secure Mounting Nuts 4 in place Wipe away any excess sealant that squeezes out during tightening Siliconized Sealant such as CELULON Plumbing amp HVAC Adhesive Sealant by Red Devil APPLY A BEAD OF SILICONIZED SEALANT APPROXIMATELY 3 8 DIAMETER THIS AREA ALL AROUND UNDERSIDE OF RIM Complete water supply and proper sanitary waste trap connections as specified by local code requirements SI 185 0806 COUNTERTOP CUTOUT DETAILS CUTOUT FOR BASKET TYPE INSTALLATION SINK OUTLINE Ref DO NOT CUT ON THIS LINE i HELPFUL HINT P Tea r CUTOUT LINE ALL AROUND Ref 203 s After making cuts along sides of cutout secure a board as shown to prevent cutout from possibly 9 E damaging countertop or prematurely dropping 2d iS 3 Gh ee lt lt Gs a DIA HOLE 4 REQ D 3 Ref esa CUTOUT FOR FOOD WASTE DISPOSAL INSTALLATION SINK OUTLINE DO NOT CUT ON THIS L2. INE n l CUTOUT LINE ALL AROUND n amp DIA HOLE 4 REQ D IMPORTANT MEASURE ACTUAL CASTING BEFORE DOING ANY CUTTING DRILLING OF COUNTERTOP SI 1485 08 06 COUNTERTOP SINK MODEL 10C SELF RIMMING PARTS LIST PART NUMBER KEY NO WHITE Bone DESCRIPTION 10 107C 10 108C Self Rimming Sink Mounting Stud 4 Required Mounting Plate 4 Required Mounting Nut 4 Required NOTE FOR REPLACEMENT HARDWARE ORDER COMPLETE PARTS PACKAGE PART NO 20 603 PACKAGES WILL NOT BE SPLIT FOR INDIVIDUAL PARTS CARE AND CLEANING The surface of your Countertop Sink may be cleaned with a mild soap in warm water using a soft cloth For stubbom stains use Soft Scrub by Clorox or Lysol Tub amp Tile Cleaner or a powdered detergent such as Spic n Span Never use abrasive scouring powder or steel wool pads as they will dull the surface A periodic coating of a silicone based marine polish will help retain the fine finish E L MUSTEE amp SONS INC 5431 West 164th Street Brook Park Ohio 44142 SI 185 08906
3. MUSTEE COUNTERTOP SINK MODEL 10C Your Countertop Sink requires a 23 3 8 x 20 3 8 countertop cutout preferably with a 1 4 radius in each comer Refer to Rough In for detail dimensions NOTE The centerline of the drain is located 12 5 16 from the back edge and 12 7 16 from either side If you choose you may use your Countertop Sink as a template for laying out the countertop cutout ROUGH IN DIMENSIONS i DIA HOLES i 3 OR AS REQ D j t37 21 MOLDED DRAIN HOLE TO ACCEPT 3 DIA BODY WITH 41 DIA FLANGE NOTE DIMENSIONS SHOWN ARE NOMINAL MEASURE ACTUAL PART BEFORE DRILLING CUTTING COUNTERTOP NOTE Numbers in parenthesis refer to Key Numbers in Parts List HINT Place Countertop Sink 1 upside down on countertop in desired location hold sink in place and scribe a guide line all around the rim with a pencil H pencil does not mark surface of countertop you may apply 2 wide masking tape to the approximate area and do the marking directly on the tape surface Leave tape in place to protect countertop surface during drilling and cutting Remove Countertop Sink For standard installation measure in 3 4 from guide line area all around this will be your cutting line Drill a 1 2 diameter hole in each corner Insert saber jig saw blade fine tooth into one of the comer holes and cut along Cutout Line See COUNTERTOP CUTOUT DETAILS BASKET TYPE INSTALLATION NOTE If installing fo
4. od waste disposal refer to COUNTERTOP CUTOUT DETAILS FOOD WASTE DISPOSAL INSTALLATION CAUTION DO NOT exceed maximum dimensions of Countertop Sink E L MUSTEE amp SONS INC 5431 West 164th Street Brook Park Ohio 44142 SI 185 08 06 7 The rear ledge of your Countertop Sink will accept many different faucets 4 CenterSet on center 4 CenterSet either right or left 8 CenterSet on center Depending on the model faucet you choose the appropriate holes will have to be drilled You will notice that there are five indented hole locators molded in on the underside of the rear ledge Do not cut out faucet holes until you have measured the actual faucet some single lever faucets require a lange center supply hole and small diameter mounting holes A 1 diameter fine tooth hole saw with center drill pilot would normally be used for the majority of faucet hole drilling Drill from the underside of rear ledge to mark center turn upright to finish cutting with hole saw from the top side i 4 INDENTED HOLES ON UNDERSIDE OF REAR LEDGE TO BE DRILLED OUT BY CUSTOMER TO ACCEPT EITHER 4 OR i i e lt 3 8 SUPPLY CENTER FAUCETS TY FAUCET HOLE DETAIL 8s i Install Basket Style Drain Assembly or Disposal Unit per manufacturers instructions The Countertop Sink is furnished with a 3 1 2 diameter drain hole Install Mounting Studs 2 in each comer lug CAUTION DO NOT OVERTIGHTEN A standard 5 16 socket or wrench is
Download Pdf Manuals
Related Search