MUSTEE 11BN Instructions / Assembly
Contents
1. 4 FOUR MOUNTING LUGS with ATTACHING HARDWARE Io a 54 DIAMETER RING 1 Place Hospitality Sink 1 upside down on countertop in desired location hold sink in place and scribe a guide line all around the rim with a pencil HINT If pencil does not mark surface of countertop you may apply 2 wide masking tape to the approximate area and do the marking directly on the tape surface Leave tape in place to protect countertop surface during drilling and cutting 2 Remove Hospitality Sink measure in 3 4 from guide line all around this will be your cutting line Measure in 3 4 in each corner this will be the center point for the 7 8 diameter hole 4 required Insert fine tooth sabre saw blade into one of the corner holes and cut along Cutout line See Countertop Cutout Details E L MUSTEE amp SONS INC 5431 West 164th Street Brook Park Ohio 44142 SI 166 6 062. Plumbing amp HVAC Adhesive Sealant by Red Devil CAULKING SEALANT 7 Complete water supply and proper sanitary waste trap connections as specified by local code requirements Numbers in parantheses refer to Key Numbers in Parts List 3 SI 166 6 06 IAPMO MUSTEE war oS HOSPITALITY SINK MODEL 11 T FILE NO 820 Your Hospitality Sink requires a 15 1 2 x 18 1 2 countertop cutout Refer to Rough In for detail dimensions NOTE The centerline of the drain is located 11 from the back edge and 8 1 2 from either side If you choose you may use your Hospitality Sink as a template for laying out the countertop cutout Measure actual part before drilling or cutting countertop CARE AND CLEANING The surface of your Self Rimming Countertop Sink may be cleaned with a mild soap in warm water using a soft cloth For stubborn stains use Soft Scrub by Clorox or Lysol Tub amp Tile Cleaner or a powdered detergent such as Spic n Span Never use abrasive scouring powder or steel wool pads as they will dull the surface A periodic coating of a silicone based marine polish will help retain the fine finish ROUGH IN DIMENSIONS pcs a 7 NOTE See Step No 3 N ana DIMENSIONS SHOWN ARE NOMINAL pu j MEASURE ACTUAL PARTS BEFORE e is RES i DRILLING CUTTING COUNTERTOP l MOLDED DRAIN HOLE TO ACCEPT 31 2 DIAM BODY BASKET TYPE DRAIN WITH 41 2 DIAM FLANGE
3. Drill from underside of rear ledge to mark center turn upright to finish cutting with hole saw INDENTED HOLES ON UNDERSIDE OF 4 REAR LEDGE TO BE DRILLED OUT BY CUSTOMER TO ACCEPT EITHER 4 OR me 8 SUPPLY CENTER FAUCETS GE NE T JL p FS necp ox Det t r FAUCET HOLE DETAIL 4 Install Basket Style Drain Assembly per manufacturer s instructions The Hospitality Sink is furnished with a 3 1 2 diameter drain hole 5 Install Mounting Studs 2 in each corner lug CAUTION DO NOT OVERTIGHTEN A standard 5 16 socket or wrench is required Screw stud in place until nut makes contact with bottom of lug continue 1 4 turn maximum Repeat this operation for each mounting lug See TYPICAL STUD INSTALLATION HINT APPLY A DAB OF SILICONIZED SEALANT TO THREADS TO LUBRICATE STUD AND EASE INSTALLATION TYPICAL STUD INSTALLATION 6 Apply a bead of clear siliconized sealant not furnished all around the underside of the rim in the molded in groove See Detail Drawing Place Hospitality Sink into the countertop cutout secure from the underside with hardware provided You will need a 7 16 socket or wrench to secure Mounting Nuts 4 in place Wipe away any excess sealant that squeezes out during tightening See CAULKING SEALANT DETAIL APPLY A BEAD OF SILICONIZED SEALANT APPROXIMATELY 3 8 DIA THIS AREA AROUND UNDERSIDE OF RIM Siliconized Sealant such as CELULON
4. MUSTEE HOSPITALITY SINK MODEL 11 SELF RIMMING COUNTERTOP MOUNTED PARTS ILLUSTRATION PARTS LIST Self Rimming Sink Mounting Stud 4 Required Mounting Plate 4 Required Mounting Nut 4 Required NOTE FOR REPLACEMENT HARDWARE ORDER COMPLETE PARTS PACKAGE PART NO 10 606 PACKAGES WILL NOT BE SPLIT FOR INDIVIDUAL PARTS E L MUSTEE amp SONS INC 5431 West 164th Street Brook Park Ohio 44142 4 SI 166 6 06 COUNTERTOP CUTOUT DETAILS SINK OUTLINE DO NOT CUT ON THIS LINE 7 8 DIA DRILLED HOLE 4 REQ D l E _ CUTOUT LINE ALL AROUND Make these cuts first After making cuts along sides of cutout secure a board as shown to prevent cutout from possibly damaging countertop or prematurely dropping SI 166 6 06 2 3 The rear ledge of your Hospitality Sink will accept many different faucets 4 Center Set on center 4 Center Set either right or left 8 Center Set on center Depending on the model faucet you choose the appropriate holes will have to be drilled You will notice that there are five indented hole locators molded in on the underside of the rear ledge do not cut out faucet holes until you have measured the actual faucet you intend to use some single lever faucets require a large center supply hole and small diameter mounting holes A 1 diameter fine tooth hole saw with center drill pilot would normally be used for the majority of faucet hole drilling
Download Pdf Manuals
Related Search