Hills FD51038 Use and Care Manual
Contents
1. 74 To extend the arm and line assembly Remove the arm from the cabinet by pulling on the two blue end caps Holding the arm firmly extend it towards the receiving bracket Fig 10 Pull both end caps to remove arm from cabinet Pull arm out of cabinet and extend towards receiving bracket 13 Step 7 continued Operation 7 2 To attach the arm and line assembly to the receiving bracket Grip the arm with each hand either side of the receiving bracket Centre the arm within the receiving bracket Rotate and guide the arm downwards to secure it onto the locking pins in the receiving bracket until a clicking sound is heard This means the arm has engaged Fig 11 2 Rotate and guide arm downwards to secure onto locking pins within the receiving bracket 14 Step 7 continued Operation 7 3 To tension and lock the line With the arm engaged correctly in the receiving bracket rotate the locking lever on the right hand side of the cabinet Fig 12 Rotate clockwise from the unlocked position until it locates in the first lock position This provides normal tension on the lines Fig 13 Check the product is locked by pulling firmly on the lines If you require extra tension on your lines rotate the locking lever further until it locates in the second lock position Fig 13 si a ee s sel Sai A a whee See es 8 Se lt TS c DAE a P E a fo2. 3 3 Mark the cabinet mount centres on the wall at the desired installation height refer to page 6 and the tabie below Mount centres z a M Ensure surrounding area is free from obstructions Mount Hole Centres Centres Centres Extendan 6 Extendam 4 22 1 2 3 4 Drill holes in wall Masonry fasteners are not included with this product When attaching to a sound masonry wall we recommend using masonry sleeve anchors diameter 10mm x 55mm If you are using these fasteners drill a 10mm 13 32 hole using a masonry 3 5 drill Fig 2 Note lf you are mounting to a different wall type consult your hardware store for advice on the appropriate fasteners to use Mount hole centres Topof ERRA Fis product mmm mrmi lst aaa Drill 2 holes using masonry drill i Product centre Step 3 continued Mounting your cabinet to a wall 3 6 Secure your cabinet to the wall Remove the end covers using a phillips head screwdriver Fig 3 3 7 Ensure square metal locking rod does not come out of the Cabinet 3 8 Locate the cabinet with the mount holes Insert masonry fasteners and secure Fig 4 3 9 Re attach cabinet end covers Fig 4 Do not overtighten the screws End cover 7 End cover screw Masonry anchor Not included Step 4 Mounting your cabinet to a post 4 1 Prepare your cabinet location Determine the best location for the i
3. FD51072 Mount Bar Extenda 4 Mounting Options Determine which of the four mounting options most suits your reguirements Wall to Wall Wall to Post AAS Requires 1 Post Kit Post to Wall Requires 1 Post Kit 1 Mount Bar Kit Post to Post Requires 2 Post Kits 1 Mount Bar Kit E Note Minimum operating distance is 4m 13 Maximum operating distance is 6 5m 21 4 Step 1 Select a suitable location 1 1 Select a suitable location for either wall or post mounted installations 1 2 This product has been designed to mount and operate between 4m 13 and up to 6 5m 21 4 1 3 Always leave approximately 1 5m 5 clearance each side of the line and any wall fence shed etc Note This product must only be installed on sound structural walls Do not mount directly onto cladding materials If you have any doubt contact your local hardware store or installer 1 5m 5 clearance from obsiructions either side Mounting surface Receiving bracket Arm Am 13 minimum m 6 5m 21 4 maximum Cabinet Mounting surface Step 2 Recommended installation height 2 1 For all installations we recommend the operational height for the line is approximately 50mm 2 above the user s head height 2 2 Forthe heights and combinations of wall post installations refer to the appropriate details below Wall installation Ca
4. es al Fig 13 If extra tensioning is istlock gt 2nd lock E pa Tt fe Se required move the position a Va W position locking lever to the 2nd lock position A WARNING if your unit is mounted at 4m distance do not use the second lock position 15 16 Step 7 continued Operation WARNING Ensure the lines are not under tension before un latching and releasing the arm 7 4 To un lock and un tension the lines With all clothes and washing removed from the lines Pull out and unlatch the locking lever from its locked position Rotate anti clockwise to its unlocked position Fig 14 Do not let go of the locking lever as it may return with some force 7 5 To remove the arm from the receiving bracket Using one hand pull the release handle forward as shown With your other hand rotate guide and lift the arm up and out of the receiving bracket Fig 15 WARNING The lines are under spring tension Do not allow the arm and lines to retract uncontrolled as this may lead to personal injury or property product damage Hold the arm securely and walk it back to the cabinet Fig 14 a Locking lever Pull out to release Rotate arm KE M and lift out of H Pm AJ receiving bracket Release handle Pull forward Release handle Hills Handy Hints When hanging thick or bulky items we suggest you lay the item over more than one line Place smaller items of cl
5. Als Extenda 4 and Extenda 6 Retracting Clothesline Owner s Manual Congratulations Congratulations on the purchase of your new Hillse Retracting Clothesline which will bring you many years of trouble free and efficient drying It is important that you read this Owner s Manual thoroughly before installation and use In this way you will benefit from all the design features and enjoy safe use of the product Thank you for choosing Hilis Warning Do not allow children or pets to swing on the Clothesline or items of laundry Do not use for any purpose other than to hang and dry washing Do not use your Clothesline if parts are worn or damaged Do not operate the locking lever when the arm is located in the cabinet Do not release the locking mechanism when there are clothes attached to the lines Do not allow the arm and lines to retract uncontrolled as this may lead to personal injury or property damage Hold the arm securely and walk it back to the cabinet Carton Contents Extenda 6 Extenda 6 cabinet Receiving bracket Patents and registered designs apply to this product Extenda 4 Qty Extenda 4 cabinet Receiving bracket Post Mount Kits if you choose to mount your Retracting Clothesline cabinet or receiving bracket on posts the following products are available Post Kits FD51044 Adjustable Post Kit Mount Bar Kits FD51070 Mount Bar Extenda 6
6. binet Receiving bracket Cabinet ie es i F fasteners t User s head height 75mm 3 50mm 2 aa Location of cabinet Location of receiving bracket fasteners are approximately fasteners are approximately 85mm 75mm 3 above user s 3 1 2 above user s head height head height when instatled on level ground Note the receiving bracket should be located at a height to ensure the clothesline is close to horizontal Post Installation Cabinet Receiving bracket Mount bar Top of post l Top of post p p PENAN ARENE E cena S aan p KA p vrois Receiving Cabinet E bracket fasteners fasteners t Users head height Post kit 115mm 50mm 2 Post kit 4 1 2 For post mounting a cabinet For post mounting a receiving the top of the post should be bracket the top of the post approximately 115mm 4 172 should be approximately 125mm above the user s head height 5 above the user s head height when installed on level ground A Note the receiving bracket should be located at a height to ensure the clothestine is close to horizontal Step 3 Mounting your cabinet to a wall 3 1 Prepare your cabinet location Determine the best location for the installation of your product refer to page 5 Mark out a centre line for your product within your allocated site 3 2 Ensure that either side of this centreline and the area where the cabinet is to be installed on the wall is free from pipes and other obstructions Fig 1
7. e 6 Ensure there are no pipes or obstructions in the surrounding area 5 2 Drill holes in the wall Refer to page 7 for instructions on drilling holes and appropriate fasteners 5 3 Securing your receiving bracket to the wall insert the masonry fasteners and secure Not included with this product Fig 8 Fig 8 2 i F E OSS 5 kn O RRR ie ee D i s te 5 iT ieee oo lt r amp HI fi e gt Put H Receiving bracket i SS SSS So OMA SS t Se a Te SSS yi M T 11 12 Step 6 Mounting your receiving bracket to a post 6 1 Prepare your receiving bracket location On the pre determined product centre locate the position for your post and receiving bracket Refer to page 5 6 2 install your post as per the instructions supplied with your post kit Refer to diagram on page 6 to determine the installation height of your post Refer to page 3 for the post kit available 6 3 Secure the receiving bracket to a post Using the fasteners supplied with your post kit attach the receiving bracket to the post kit assembly Fig 9 Receiving bracket fi 9 8 T M8 nyloc nut Washer Washer Post kit Bolt M8 x 70 socket head bolt sold separately Step 7 Operation A WARNING Do not operate the locking lever when the arm is located in cabinet WARNING Do not release the locking mechanism when there are clothes attached to the lines
8. ls com au A Hills Hills Industries Limited AB N 35 007 573 417 Issue March 2010 PD1871
9. nstallation of your product refer to page 5 Mark out a centreline for your product within your allocated site 4 2 Determine your post locations install as per the instructions supplied with your post kit Refer to diagram on page 6 to determine the installation height Refer to page 3 for the post kit available 4 3 Jo post mount your cabinet you will need to purchase a matching mount bar kit refer to page 3 4 4 Attach the mount bar to the post as per instructions supplied with your mount bar kit Yip Ensure surrounding area is free from obstruction 10 Step 4 continued Mounting your cabinet to a post 4 5 Securing your cabinet to a post Remove end covers using a phillips head screwdriver Fig 6 4 6 Ensure square metal locking rod does not come out of the Cabinet 4 7 Locate the cabinet with the pre drilled holes in the mount bar sold separately Using the fasteners and instructions provided with the mount bar kit secure the cabinet to the post assembly Fig 7 4 8 Reattach cabinet end covers Fig 7 End cover S33 End cover screw End cover Post kit soid separately Mount bar sold separately M8 nyloc nut Washer Washer lt v ko i M8 x 45 socket head bolt 7 Step 5 Mounting your receiving bracket to a wall 5 1 Prepare your receiving bracket location Mark the mount hole centres on your pre determined centreline at the desired height refer to pag
10. othing on the lines at the back and work your way outwards for larger items When you don t expect to fill the capacity of your clothesline hang your clothes on the outer lines as this will allow clothes to dry more easily Care and Maintenance Regularly inspect all components and check for wear and tear or damage Ensure fasteners are secure If there is any damage parts should be replaced with original Hills spares The Clothesline should be repaired before using again Your Clothesline should be periodically wiped clean with a damp cioth and mild detergent We do not recommend the use of oil or WD type lubricants on any part of the Clothesline To maintain appearance and durability of coatings on metal components we recommend a twice yearly application of a reputable brand of car polish or wax 17 18 Hills Guarantee Hills Industries Limited undertakes that if any part of its manufacture has failed to operate correctly due to faulty workmanship or defective material it will repair or replace the part free of cost for a period of TEN 10 years from date of purchase of the article given fair wear and tear Tne PVC line is guaranteed for a period of ONE 1 year Evidence of unfair usage or incorrect adjustment by the owner will void this promise Hills Industries Limited will not be responsible for any costs in connection with freight or postage or for expenditure necessary to dismantle the article replace the pa
11. rt in position and re assemble the article This guarantee is in addition to any legal rights or remedies conferred on the consumer Hills Industries Limited does not recommend the application of a canopy on any of their outdoor dryer range Unless any addition or attachment to this product has Hills specific approval or is sold as a Hills product the warranty on this product is waived The product is designed to perform a specific task under established test loads and unauthorised attachments may produce stresses for which the design is not appropriate Designs specifications and colours are subject to change without notice Please retain this Owner s Manual Record the following information from the carton for future reference Date of DUPCM ASO tis 2sen vista dee kol a Designed and tested under a luatity System that meets Hills demanding quality specifications Name and focation of store mmmamrre Made in China Hills Contacts As a proudly Australian company we are committed to provide you with complete customer satisfaction If you have questions about this product or find there are missing or damaged parts please contact your nearest Consumer Advice Centre during their focal business hours Australia North America 1300 300 564 877 534 1371 Eastern info hills com au gsutterlin verizon net New Zealand South Africa 09 262 3052 021 442 1540 sales hills co nz info stingray co za or visit www hil
Download Pdf Manuals
Related Search