Rubbermaid FG3H8900TITNM Instructions / Assembly
Contents
1. 4 8 ft Deluxe Closet Kit I i SOT TREE by Rubbermaid P configurations Rubbermaid Home Products Fairlawn Ohio 44333 3306 1 888 895 2110 www rubbermaidcloset com ANewellRubbermaid Company Tools Needed e 0 Cc gt for Installation 1 8 Please read through the instructions completely and check that you have all parts before beginning the configuration you choose to install you may not use all the components peti a 48 25 Shelf labeled A ES E 48 25 Shelf labeled B 26 25 Shelves labeled A 26 25 Shelves labeled B 47 5 Uprights 25 Uprights 3G65 2 AAA Brackets 3G63 19 48 Hang Rails 3667 2 22 Rail Covers 3157 4 Rod Hangers 3668 9 48 Taner Clothes Rod 3G76 1 48 Outer Clothes Rod 367 1 36 Inner Clothes Rad 302 1 36 Outer Clothes Rod 3673 1 The following parts are packed together in a hardware bag Clothes Rod End Caps 3G71 6 bas Screws 1603168 16 pr Anchors 3J65 11 A Anchor Key 3J66 1 1070770 Upright Clips 2 Rail Covers Mount Extendable Hang Rails Spaced no more than 24 On closet wall locate all wall Position first Hang Rail so Level Hang Rail and mark holes 86 5 above floor that studs and mark them 86 5 that the rail is touching the land on studs then drill2. 1 8 pilot holes for screws above the floor left side of your closet If there is a wall stud within 4 of the LEFT end of the Hang Rail proceed to step D Starting at left side fasten the FIRST TWO screws into studs or anchors Do not fasten remaining screws until after next step Note Screws need to be fastened through Rail into EACH wall stud spaced no more than 24 apart Ga Slide second Hang Rail down behind the Slide second Hang Rail to the right wall Install screws into studs or anchors first from above of the closet and then back it away from along Rails the right wall until the holes in the two Rails line up Repeat Step C to secure to the wall If there is not a stud within 4 of the RIGHT end of the Hang Rail repeat the Wall Anchor Installation step above PA Hang Uprights g Upris OS A Se ee Hang first two 47 5 Uprights Position BOTH outside Uprights Mark bottom hole of Upright Fasten screw into stud or Wall over the Hang Rail 2 from the right and left Drill 1 8 pilot hole into stud Anchor No screws are needed corners by using the 2 Rail Use Wall Anchor and 3 8 bit in top holes of Uprights Cover for spacing if there is no stud Helpful hint If the left side of closet is more accessible space the remaining Uprights from left to right If the right side of the closet is more accessible space the remaining Uprights from right to left A Clip 2 Rail
3. Cover over Hang Rail Hang another 47 5 Upright on the Rail and use Ifthe space between the last Uprights is less one of the 22 Rail Covers to space over 22 than 22 you may choose to cut Rail Cover with Drill 1 8 pilot hole and fasten screws in bottom scissors to fit hole Use Wall Anchor and 3 8 bit if there is no stud Place 22 Rail Cover over Rail between Uprights Repeat Step F for one or two more Uprights if space allows Note Install these in the area of the closet where you would be most likely 3 l Install Upr ight Extensions to install accessories sold separately or shelving closer to the floor Pie Se i Slide one end of the Upright Slide the other end of the Upright Drill 1 8 pilot hole and fasten both screws Use Wall Anchor and connector into the top two connector into the bottom two 3 8 bit if there is not stud To position the second Upright 1 notches of the short Upright notches of the long Upright Extension use 22 Rail Cover to ensure proper spacing from the Use a level to position theshort first Upright Extension Upright and mark the position of the top amp bottom screw holes Install Brackets amp Adjustable Shelves Insert Brackets into Uprights at desired Shelves are fully adjustable and require no Make sure the Bracket locks are unlocked locations Note Install Brackets and cutting To adjust width overlap the shelves and install shelving making sure that the
4. expanding Clothes Rod to of Bracket by tilting it backward or telescoped together up to 8 of each Clothes Rod End Caps desired length place into Rod until it locks in place 26 Rods can be used separately will fit either diameter of Rod Hangers and press down to snap or telescoped together up to 4 as shown above into place Note Do not extend more than 3 past Rod Hangers Fully Adjustable System Configurations Accessories Shelves and Clothes Rods can be adjusted or reconfigured The following accessories are sold separately anywhere on this system to meet your storage needs cada beshosSheles Additional configurations can be created by overlapping z a Rods shorter shelves to create longer shelves Example overlapping three 2 shelves creates a 6 shelf e Sliding Basket e Change your closet design seasonally to better accommodate e Sliding Pants Rack summer or winter clothing e Tie and Belt Organizer
5. shelving at the top first and work down making sure the shelf labeled A is placed nose of the Bracket is projecting out Brackets will not fit into upper two slots first on the Brackets and the shelf labeled B through the front edge of the she f of each Upright is placed ON TOP of A Note For maximum weight capacity do not insert Brackets into bottom slots IMPORTANT Regardless of overall Shelf length when overlapping sections of shelving of Uprights shelves labeled A must be placed onto brackets before shelves labeled B E Shelf labeled A sits in front notch of Bracket Shelf labeled B sits in back notch After all shelves are positioned Be sure each shelf slides back as far as possible before locking shelves into Brackets pore oe ah is e B i i i WARNING If shelves are installed in the incorrect notch the front of locking clip a en the shelves may fall off the Bracket It will SNAP into locked position If overlapping 3 sections of shelving use two A sections and one B section placing A sections on the outside and gapping the bridge with the B section For 4 or more overlapping sections continue alternating between A and B sections placing A shelves on brackets before B shelves Install Adjustable Clothes Rods End Cap End Cap fiton Outer fiton Inner Clothes Rod Clothes Rod Install Rod Hanger into bottom 48 Rods can be used separately Place End Caps on the end After
Download Pdf Manuals
Related Search