ShelterLogic 70403.0 Instructions / Assembly
Contents
1. REPLACEMENT PARTS ASSEMBLY SPECIAL ORDERS Genuine ShelterLogic LLC replacement parts and accessories are available from the factory including anchoring kits for nearly any application replacement covers wall and enclosure kits vent and light kits frame parts zippered doors and other accessories All items are shipped factory direct to your door QUESTIONS CLAIMS SPECIAL ORDERS CALL OUR CUSTOMER SERVICE HOTLINE U S CUSTOMER SERVICE 1 800 524 9970 INTERNATIONAL CUSTOMER SERVICE 001 860 945 6442 CANADA CUSTOMER SERVICE 1 800 559 6175 HOURS OF OPERATION MON FRI 8 30AM 8 00PM EST SAT SUN 8 30AM 5 00PM EST CARE AND CLEANING A tight cover ensures longer life and performance Always maintain a tight cover Loose fabric can accelerate deterioration of cover fabric Immediately remove any accumulated snow or ice from the roof structure with a broom mop or other soft sided instrument Use extreme caution when removing snow from cover always remove from outside the structure DO NOT use hard edged tools or instruments like rakes or shovels to remove snow This could result in punctures to the cover DO NOT use bleach or harsh abrasive products to clean the fabric cover Cover is easily cleaned with mild soap and water WARRANTY This shelter carries a full limited warranty against defects in workmanship ShelterLogic LLC warrants to the Original Purchaser that if properly used and installed the product and all assoc2. L 802443 802439 800071 800071 800071 802443 802439 L 800601 800601 800601 2 ASSEMBLE ROOF FRAME Use bolts as shown in illustrations Top Cross Rail OVER Middle Ribs 802443 802630 802443 Use 802439 at Front End Rib Use 802443 at Back End Rib Middle Rib ShelterLock Assembly Fas Side Bend Connector and ShelterLock 800597 802497 sO ShelterLocks and Cross Rail Poles attach to inside of frame a 802439 Page 4 05 70403 0H 3 ASSEMBLE LEGS amp ATTACH TO ROOF FRAME Use bolts as shown in illustrations A Assemble Corner and Middle legs B Attach legs with bolts on one side of roof frame let the other side of roof frame rest on the ground C Attach remaining legs with bolts to opposite side of roof frame Corner Legs Middle Legs Attach Legs to Roof Frame Use Bolt m Use Bolt 03032 03032 Bt 802445 Use Bolt 802285 10115 Assembled Leg 802610 Ka Corner Legs Middle Legs 4 ASSEMBLE COVER RAILS A Place the cover rail 13215 at each leg and secure it at each leg with a cover clamp as shown below B Slide the cover rails so they are 8 inches up from the ground and hand tighten bolts on clamps Middle Rib Cross Rail Clamps 01011 802427 Page 5 05 70403 0H 5 SQUARING UP THE FRAME A Place frame in its final location which needs to be as flat and level as possible B Me
3. electrical wires Check for overhead utility lines tree branches or other structures Check for underground pipes or wires before you dig DO NOT install near roof lines or other structures that could shed snow ice or excessive run off onto your shelter DO NOT hang objects from the roof or support cables WARNING Risk of fire DO NOT smoke or use open flame devices including grills fire pits deep fryers smokers or j lanterns in or around the shelter DO NOT store flammable liquids gasoline kerosene propane etc in or around your shelter Do not expose top or sides of the shelter to open fire or other flame source IK CAUTION Use CAUTION when erecting the frame Use safety goggles during installation Secure and bolt together overhead poles during assembly Beware of pole ends PROPER ANCHORING AND INSTALLATION OF FRAME PROPER ANCHORING OF THE FRAME IS THE RESPONSIBILITY OF THE CONSUMER ShelterLogic LLC is not responsible for damage to the unit or the contents from acts of nature Any shelter that is not anchored securely has the potential to fly away causing damage and is not covered under the warranty Periodically check the anchors to ensure stability of shelter ShelterLogic LLC cannot be responsible for any shelter that blows away NOTE Your shelter s cover can be quickly removed and stored prior to severe weather conditions If strong winds or severe weather is forecast in your area we recommend removal of cover
4. 6 x 10 x 6 6 Shed in a Box Peak Style Shelter Assembly Instructions DESCRIPTION MODEL 6 x 10 x 6 6 Shed in a Box Gray 70403 RECOMMENDED TOOLS Please read instructions COMPLETELY before assembly This shelter MUST be securely anchored THIS IS A TEMPORARY STRUCTURE AND NOT RECOMMENDED AS A PERMANENT STRUCTURE Before you start 1 individual recommended for assembly approximate time 2 hr a shelter 150 Callender Road Canada Watertown CT 06795 www shelterlogic com 1 800 559 6175 9 8 10 Page 1 05 70403 0H ATTENTION This shelter product is manufactured with quality materials It is designed to fit the ShelterLogic LLC custom fabric cover included ShelterLogic LLC Shelters offer storage and protection from damage caused by sun light rain tree sap animal bird excrement and light snow Please anchor this ShelterLogic LLC structure properly See manual for more anchoring details Proper anchoring keeping cover tight and free of snow and debris is the responsibility of the consumer Please read and understand the installation detail warnings and cautions prior to beginning installation If you have any questions call the customer service number listed below Please refer to the warranty card inside this package DANGER Prior to installation consult with all local municipal codes regarding installation of temporary shelters Choose the location of your shelter carefully DANGER Keep away from
5. asure across opposite corners These distances must be equal to within 1 inch C Check that the front and rear of the frame measures 6 feet in width 6 PROPERLY ANCHOR THE FRAME A Anchors must be placed inside shelter at the corners of the shelter B Insert a inch pipe or steel rod through the eyelet of the auger and screw the anchor into the ground until the eyelet is sticking out of the ground by 1 to 2 inches so it can be anchored to the legs If ground is too hard dig a hole with a shovel or post hole tool Optional Fill with cement C Wrap cable provided through the eyelet of the anchor and around the frame as shown below Secure the cable with the clamps provided NOTE 15 Augers are for temporary use only For best results ShelterLogic recom mends using our Easy Hooks 10036 4 pack 10035 6 pack or 10038 8 pack or 30 Augers 10075 4 pack 10078 6 pack or 10079 8 pack for a stronger more secure End Rib Anchors installation Call 1 800 524 9970 or visit www shelterlogic com for more information Page 6 05 70403 0H 7 DOOR AND SOLID END PANEL INSTALLATION A Hold end panel at the top center with white inner surface facing inside of the shelter Wrap the edges of the fabric panel around the end rib B Disconnect top rail from the end rib Pass the top cross rail through the gap in the fabric in between th
6. e S Hook on ratchet into hole on the leg bend Insert the webbing into the spindle of the ratchet and pull tight Wind the ratchet so that the webbing overlaps itself D Disassemble cover rails and slide through fabric pockets at each leg and reattach with clamps to each leg Repeat this on other side Push down on cover rails to tighten cover before tightening bolts completely E Check and tighten Ratchets and Cover Rails monthly to ensure the cover is tight NOTE The ShelterLogic logo should be oriented as shown below CORRECT REAR 3 FRONT Middle Rib Cross Rail Clamps End Rib Cross Rail Clamps Webbing and Ratchets Securing Cover 802445 13201 13202 C amp N D 01011 Page 8 05 70403 0H
7. e webbing and rib frame Re attach top cross rail to end rib Repeat Step B for side cross rails C At the bottom where the webbing exits the pocket on each side of end panel pull webbing to remove the slack Be careful not to pull the webbing through the other side of the webbing pocket fee tm Do Not insert any pipes into these pockets D Insert the S Hook on ratchet into hole on the leg bend Insert the webbing into the spindle of the ratchet and pull tight Wind the ratchet so that the webbing overlaps itself Position the end panel so that it is centered on the building before fully tightening the end panel E Tighten ratchets alternating from one side to the other until the end panel is centered and tight Zipper Door Panels Zippers must be closed when tightening end panel WRAP END PANEL EDGES TO INSIDE OF FRAME sN TOP CROSS AE WRAP END PANEL EDGES TO INSIDE OF FRAME SIDE CROSS RAILS WEBBING INSIDE VIEW OF END RIB SIDE VIEW OF END RIB Thread Webbing Into Ratchet Webbing and Ratchets Securing End Panel Page 7 05 70403 0H 8 INSTALLING COVER AND COVER RAILS A Lay the cover on the ground next to the frame with inside of the cover the side with the pipe pockets facing down and the webbing on the front and rear of the corner of the building B Pull cover over the frame making sure to center cover on frame There should be an equal amount of over hang at all four corners C Insert th
8. iated parts are free from manufacturer s defects for a period of 1 YEAR FOR COVER FABRIC END PANELS AND FRAMEWORK Warranty period is determined by date of shipment from ShelterLogic LLC for factory direct purchases or date of purchase from an authorized reseller please save a copy of your purchase receipt If this product or any associated parts are found to be defective or missing at the time of receipt ShelterLogic LLC will repair or replace at it s option the defective parts at no charge to the original purchaser Replacement parts or repaired parts shall be covered for the remainder of the Original Limited Warranty Period All shipping costs will be the responsibility of the customer Parts and replace ments will be sent C O D You must save the original packaging materials for shipment back If you purchased from a local dealer all claims must have a copy of original receipt After purchase please fill out and return warranty card for product registration Please see warranty card for more details Covered by U S Patents and patents pending 6 871 614 6 994 099 7 296 584 D 430 306 D 415 571 D 414 564 D 409 310 D 415 572 080310 Page 2 05 70403 0H 6 x 10 x 6 6 Shed in a Box Parts List Model 70403 Description of Parts Quantity Part Rafter Poles 35 1 8 e 800071 TF Cross Rails Swedge 41 5 8 6 802443 J Cross Rails 40 1 2 3 802439 Cross Rails 38 1 8 13215 J Uprigh
9. t Poles 26 3 8 802285 5 Upright Poles Swedge 18 1 8 4 802440 E f j Middle Poles 36 3 4 4 802445 Corner Leg Bends 4 802427 E Side Corners 800601 Ey Top Connectors 4 802606 Steel Foot Plate 4 802610 4 Bolts 1 4 x 1 5 8 16 4 Bolts 1 4 x 3 3 8 Washer 1 4 12 Nut 1 4 28 01010 White Bungee Cords For holding door open 4 10066 Bolt Caps For bolt 802497 10150 Half Clamps for Middle Legs 13201 Half Clamps for Corner Legs 13202 Cover 1 802401 2 Zipper Door 2 802402 15 Auger Anchors Temporary Cable 1 Length Cable Clamps Page 3 05 70403 0H 1 LAY OUT ROOF FRAME 800601 802443 800071 802606 802443 800071 802443 800601 800601 800601 800601 L 802443 802439 800071 800071 800071 802606 802606 802606
Download Pdf Manuals
Related Search