SPT CL-010 Use and Care Manual
Contents
1. board 1 for ward until it is tightly stuck and Job s tears should be first soaked in water overnight and then soaked in water double volume of the grains for 30 minutes next day before being milled Please use the mixer according to the following steps Turn on the switch allow the flush board to be fixed pour food grains in place the drip dish in the funnel before pouring water in it and then the flush board slowly moves away In the operation the water of the drip dish should be kept as full as 80 to 90 all the time and power source cannot be turned off without any cause After you use it rinse every part and then re assemble them and dry them by means of dehydrating When you prepare rice milk with this mixer you can cover half of the drip hole in the middle of the drip dish with a tape and use half regular volume of water if you want to make it thicker After the mixer is switched on if the motor does not run resulting in the auto off by the switch please rinse the parts amp and the top of the motor housing before re assembling them Tighten up the nut with the screw spanner before switching it on Use it only when you confirm its normal operation Plastic portion should not be washed with hot water or dried by heater for fear of deformation Food grains to be milled should not be mixed with any stone chips otherwise the mixer will be damaged If the switch automatically cuts off power source becaus2. ASSEMBLY METHOD OF THE MILL MIXER FOR VARIETIES OF FOOD GRAINS Hold the nut with the larger Obirst hold the handle with the Oplace rice in the funnel then hole of the screw spanner 6 1 index fingers with the other fingers pour water into the drip dish and fasten the nut Take the just under its bending portions and anq place it on the funnel z the thumbs upward then pull it screw spanner out after working backward ty it gets oo a recess of the top lid and is fixed Place the motor housing on a When varieties of food grains flat table top except for soy beans are to be milled please use the rice mill pad instead of a dehydrating bowl PN gt a n Okiee mill pad DISASSEMBLY OF THE MILL MIXER REASSEMBLE THE PARTS IN THE SEQUENCE FROM THE BOTTOM TO THE UP EE Place the bottom stand on the Place the miller with its motor housing Be careful that pattern upward on the rice mill the tenon of the bottom stand pad 4 should be inserted in the recess Check the plastic flake O by Lock the nut on the screw of the screw bolt the motor housing Combine the top lid and the bottom stand Be careful of set ting the protrusion of the top lid in the recess of the bottom stand Mi NOTE Directions Harder food grains other than rice and wheat such as green beans red beans Insert the funnel in the round hole of the top lid and push the flush
3. e of improper use please wash the dismantled parts first and then re start it ASSEMBLY METHOD OF THE MILL MIXER FOR SOY BEANS DH e screw nut with t OFirst hold the handle with the Place soy beans in the funnel larger hole of the screw index fingers with the other fingers then pour water into the drip spanner 1 and fasten the nut just under its bending portions and dish and place it on the funnel Take the screw spanner out after the thumbs upward then pull it gt ne backward until it gets into the oe ae recess of the top lid and is fixed Place the motor housing on a When soy beans are to be milled flat table top please check the dehydrating bow O by the screw bolt in alignment with the rectangular hole REASSEMBLE THE PARTS at Po a eee eae e i rA Combine the top lid 2 and the Insert the funnel 9 in the Place the dredge container at bottom stand Be careful of round hole of the top lid and the dredge outlet setting the protrusion of the push the flush board 1 for Ei top lid in the recess of the ward until it is tightly stuck OPlace the miller with its bottom stand motor housing Be careful that pattern upward in the ad ae eee eee the tenon of the bottom stand dehydrating bowl and check M NOTE Directions Please use the mixer according to the following steps Turn on the switch allow the f
4. embled one by means of dehydrating After the mixer is switched on if the motor does not run resulting in the auto off by the switch please rinse the parts 3 amp 4 and the top of the motor housing before re assembling them Tighten up the nut with the screw spanner then switch it on again Use it only when you confirm its OTighten ighten up the blade disk with the screw spanner when normal operation necessary The screw spanner Plastic portion should not be washed with hot should not be left in the water or dried by heater for fear of deformation mixer
5. lush board to be fixed pour food grains in place the drip dish in the funnel before pouring water in it and then the flush board slowly moves away In the operation the water of the drip dish should be kept as full as 80 to 90 all the time and power source cannot be turned off without any cause After you use it dismantle it to rinse the parts and then dry the re assemble mixer by means of dehydrating When you prepare soy bean milk with this mixer you can cover half of the drip hole in the middle of the drip dish with a tape and use half regular volume of water if you want to make it thicker After the mixer is switched on if the motor does not run resulting in the auto off by the switch please rinse the parts amp and the top of the motor housing before re assembling them Tighten up the nut with the screw spanner before switching it on Use it only when you confirm its normal operation Plastic portion should not be washed with hot water or dried by heater for fear of should be inserted in the recess it by the screw bolt W L fn O j J O ua al T It all 2 E On ad 5 LL i W O i ra LL i 4 W IE 19 W T l ig A deformation Soy beans to be milled should not be mixed with any stone chips otherwise the mixer will be lt damaged EES If the switch automatically cuts off power source because of improper use please wash the dismantled parts first a
6. nd then re start it Check the plastic flake by Oloch the nut on the screw of the screw bolt the motor housing DISASSEMBLY OF THE MILL MIXER V fun ig lt A L J bn W d 10 2 W V q w x W 2 2 x LL W J LL O l m 2 W U q 0 a IN THE SEQUENCE FROM THE BOTTOM TO THE UP OPlace the maor O on a flat table top motor housing Be careful that the tenon ge stand Ee AT T OCheck the plastic flake Q by the screw bolt aa a a OCheck the dehydrating bowl Combine the top lid and the Place the dredge container by the screw bolt in alignment bottom stand Be careful of at the dredge outlet with the rectangular hole setting the protrusion of the top e aie the ecens of the botto stand fer pie i pi 3 n y Soe LLO aeae s First hold the handle with the Push the fruit to be squashed bowl and fasten _ index fingers with the other in with the pusher stopper Q it by turning it clockwise fingers just under its bending portions and the thumbs upward then pull it backward until it gets into the recess of the top lid and is fixed M NOTE Directions bDon t place any thing in the mixer before it is switched on Don t use too soft or over ripe fruit whose dredges and juice cannot be separated After using it dismantle it to wash the parts and dry the re ass
Download Pdf Manuals
Related Search