Amana DK900D Installation Guide
Contents
1. DRAIN KIT INSTALLATION INSTRUCTIONS Combination Drain Kit for outdoor or indoor sleeve drainage The installation and servicing of the equipment should be done by qualified experienced technicians Description This kit is used to control condensate from the unit Con densate water drains from the chassis into the sleeve during normal heat pump operation and during times of high humidity when the unit is in cooling operation The drain kit allows the condensate from the outdoor and indoor coils to be routed to a suitable area It can be installed for either outdoor or indoor use For outdoor use the condensate can be drained from either the right or left hand side of the wall sleeve Local codes will determine the proper condensate disposal For indoor use the drain components must be installed on the bottom of the wall sleeve and connected to a drain system inside the building NOTE This drain kit serves only as a link between the unit and field supplied condensate drain system Installing the kit without connecting it to a drainage system will result in inadequate condensate removal possible leakage and corrosion ALGAECIDE Most algaecide products will cause dam age to the unit basepan or coils and should not be used Contact your sales representative for the recommended algaecide pan treatment for your unit L gt Indoor Indoor SOS brain Fitting Drain Gasket Fitting Indoor Outdoor Mtg Screws Indoor Drain Qty 2 Dr2. ain Fitting Fitting wy CO Plate Outdoor Mtg Screws S N Qty 4 amp ws Blank Off Outdoor cry Plate Qty 2 Drain Fitting Gasket Qty 2 Drain Kit Components Installation for Outdoor Use The drain components for outdoor use must be installed before the wall sleeve condenser grille 1 Remove the rear enclosure panel and the sleeve stiffener NOTE These items can be removed from the inside of the building 2 Install the outdoor drain fitting and one of the outdoor drain fitting gaskets over one of the drain holes on the rear of the wall sleeve using two of the provided outdoor mounting screws 3 Cover and seal the remaining drain hole using the remaining outdoor drain gasket blank off plate and outdoor screws If unit chassis installed right away Install the condenser grille to wall sleeve with hardware provided See condenser grille installation instructions If unit chassis is not installed right away Replace the rear enclosure panel in the wall sleeve to protect the inside of the building from weather damage Part No A3494907 Printed in U S A Blank Off Installation March 2004 Installation for Indoor Use The components of the wall sleeve drain kit for indoor use are shown in figure below These components must be installed prior to the installation of the wall sleeve MTG SCREWS 2 WALL Y SLEEVE f BOTTOM Detail A 1 Locate an area on the wall sl
3. eeve that will be inside the room when the sleeve is installed If a subbase is installed locate the kit a minimum of 3 1 2 from the front flange of the wall sleeve This clearance will provide adequate clearance for the subbase 2 Cutout the template shown to the right Using this template locate and drill the drain kit holes as close to the outside wall as possible 3 Using detail A above as a guide assemble the drain gasket drain fitting plate and indoor drain fitting to gether Install the assembly into the drilled holes and secure using the two indoor mounting screws pro vided The screws must be inserted INSIDE the wall sleeve and TOP driven down into the drain fitting plate Ensure drain tube is not restricted Cover the two screw heads with a good quality outdoor caulking not supplied for additional corrosion protection NOTE If the drain fitting is not connected to an indoor drainage system immediately after the wall sleeve is installed plug the hole with cork not included to prevent indoor water damage in case it rains 4 Install a 1 2 ID tube or hose not included on the drain fitting and interconnect it to the drain system inside of the building Ensure that there are no kinks or traps in Kinks or traps can cause improper tube or hose drainage 5 Install the two drain blank off plates and outdoor drain gaskets on the outdoor portion of the wall sleeve as shown in the figure above These c
4. omponents can be installed after the sleeve is secured in the wall opening just prior to the installation of the condenser grille and chassis SS ie 500 DIA of 187 DIA Oeics MTG HOLES ai MIN 687 gt 687 gt l l l l l l l l DIM l l l l l l l l 3 5 Min for PTSB clearance not to INSIDE EDGE OF scale FRONT SLEEVE FLANGE y Template Due to policy of continual product improvement the right is reserved to change specifications and design without notice Made in USA
Download Pdf Manuals
Related Search