Electrolux EI30BM60MS Installation Guide
Contents
1. CAUTION Be careful to avoid pinching fingers between the back of the mounting plate and the wall 4 Tighten all bolts Pull the plate away from the wall to help tighten the bolts Installation Instructions USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET You need to drill holes for the top support screws a hole large enough for the power cord to fit through and a cutout large enough for the exhaust adaptor Read the instructions on the TOP CABINET TEMPLATE Tape it underneath the top cabinet Drill the holes following the instructionson the TOP CABINET TEMPLATE CAUTION Wear safety goggles when drilling holes in the cabinet bottom ADAPTING MICROWAVE BLOWER FOR OUTSIDE TOP EXHAUST Place the microwave in its upright position with the top of the unit facing up Blower Plate Microwave Blower M otor Screw Remove the screw that holds the blower plate to the microwave Remove and save the screw holding the blower motor to the microwave 13 Carefully pull out the blower unit The wires will extend far enough to allow you to adjust the blower unit Back of Microwave Roll the blower unit 90 so that fan blade openings are facing out the top of the microwave Before Rotation After Rotation Back of Microwave Microwave 4 Place the blower unit back into the opening AFTER Fan Blade Openings Fac2. OUTSIDE TOP EXHAUST OUTSIDE BACK EXHAUST VERTICAL DUCT HORIZONTAL DUCT Adaptor Must Be Moved to the Back for Adaptor in Race for Outside Back Exhaust Qutside Top Exhaust See page 16 See page 12 RECIRCULATING NON VENTED DUCTLESS On models shipped for recirculating exhaust a disposable charcoal filter is factory installed to help remove smoke and odors See page 20 Installation Instructions INSTALLATION INSTRUCTIONS FOR EXTERNAL EXHAUST DUCTING NOTE If you need to install ducts note that the total Maximum duct length duct length of 3 x 10 8 2 x 25 4 cm rectangular or For satisfactory air movement the total duct length of 5 10 5 cm diameter 6 15 2 cm diameter round duct 3v x 10 8 2 x 25 4 cm rectangular or 5 10 5 cm should not exceed 120 equivalent feet 36 5 m diameter 6 15 2 cm diameter round duct should not Outside ventilation requires a EXTERNAL EXHAUST exceed120 equivalent feet 36 5 m DUCT Read the following carefully e NOTE It is important that venting be installed using Elbows transitions wall and roof caps the most direct route and with as few elbows as possible C present additional resistance to airflow and are This ensures clear venting of exhaust and helps prevent equivalent to a section of straight duct which is longer blockages Also make sure dampers swing freely and than their actual physical size When calculating the total nothi
3. 4 Install the charcoal filter Lay the filter on the back of the grille with the black mesh face upper Tabs Charcoal filter uw x pd a C 3 C INL C 3 rp 3 Coot TD cot 3 3 3 c D ao 2 LXI c o a aa essa ew Sh or Replace the grille and the screws Close the door rn Installation Instructions BEFORE YOU USE YOUR MICROWAVE Make sure the microwave oven has been installed according to instructions Remove all packing material from the microwave oven 3 Install turntable ring and glass tray in cavity 4 Plug power cord into a dedicated 15 to 20 amp electrical outlet SHA D Ensure proper 8 ground exists i before use me 5 Replace house fuse or turn breaker back on 23 Read theU SE amp CARE Manual KEEP INSTALLATION INSTRUCTIONS FOR THE LOCAL INSPECTOR S NOTE IT IS VERY IMPORTANT TO READ AND FOLLOW THE DIRECTIONS IN THE INSTALLATION INSTRUCTIONS BEFORE PROCEEDING WITH THIS REAR WALL TEMPLATE This Rear Wall Template serves to position the bottom mounting plate and to locate the horizontal exhaust outlet 1 Use a level to check that the template is positioned I accurately 2 Locate and mark at least one stud on t
4. holes for the top support screws and a hole large enough for the power cord to fit through Read the instructions on the TOP CABINET TEMPLATE Tape it underneath the top cabinet Drill the holes following the instructions on the TOP CABINET TEMPLATE CAUTION Wear safety goggles when drilling holes in the cabinet bottom Installation Instructions CHECK BLOWER PLATE Blower Plate Place the microwave in its upright position with the top of the unit facing up Check to see that the blower plate is correctly installed on the unit FOR EASIER INSTALLATION AND PERSONAL SAFETY WE RECOMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN IMPORTANT Do not grip or use handle during installation NOTE If your cabinet is metal use the nylon grommet around the power cord hole to prevent cutting of the cord NOTE We recommend using filler blocksif the cabinet front hangs below the cabinet bottom shelf IMPORTANT If filler blocks are not used case damage may occur from overtightening screws 21 NOTE When mounting the microwave oven thread power cord through hole in bottom of top cabinet Keep it tight throughout Steps 1 3 Do not pinch cord or lift oven by pulling cord Lift microwave tilt it forward and hook slots at back bottom edge onto four lower tabs of mounting plate Rotate front of oven up against cabinet bottom Insert a self aligning screw throu
5. oven in place against the wall and the top cabinet Install grease filters See the Owner s packed with the microwave 15 ADJ UST THE EXHAUST ADAPTOR Open the top cabinet and adjust the exhaust adaptor to connect to the house duct Back of Damper Microwave PE Blower Plate P c 7 JJ a o f For Front to Back or Side to Side Adjustment Slide the Exhaust Adaptor as Needed xs CONNECTING DUCTWORK Extend the house duct down to connect to the exhaust adaptor Seal exhaust duct joints using furnance duct tape for high temperature applications Installation Instructions OUTSIDE BACK EXHAUST Horizontal Duct INSTALLATION OVERVIEW B1 Prepare Rear Wall B2 Remove Blower Plate B3 Attach Mounting Plate to Wall B4 Prepare Top Cabinet B5 Adjust Blower B6 Mount the Microwave Oven IMPORTANT NOTES Make sure the screws for the blower motor and blower plate REAR WALL TEMPLATE are securely tightened when they are reinstalled This will help to prevent excessive vibration Make sure the motor wiring has been properly routed and secured and that the wires are not pinched PREPARING THE REAR WALL FOR OUTSIDE BACK EXHAUST You need to cut an opening in the rear wall for outside exhaust Read the instructions on the REAR WALL TEMPLATE Tape it to the rear wall Cut th
6. ANT NOTES Make sure the screws for the blower motor and blower plate are securely tightened when they are reinstalled NN This will help to prevent excessive vibration Make sure the motor wiring has been properly routed and secured and that the wires are not pinched ATTACH THE MOUNTING PLATE TO THE WALL Attach the plate to the wall using toggle bolts At least one wood screw must be used to attach the plate to a wall stud 1 Remove the toggle wings from the bolts 2 Insert the bolts into the mounting plate through the holes designated to go into drywall and reattach the toggle wings to 24 19 mm onto each bolt To use toggle bolts Spacing for Toggles More Than Wall gt i Thickness Toggle W ings M ounting li j Toggle Bolt End Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount the plate NOTE Before tightening toggle bolts and wood screw make sure the tabs on the mounting plate touch the bottom of the cabinet when pushed flush against the wall and that the plate is properly centered under the cabinet CAUTION Be careful to avoid pinching fingers between the back of the mounting plate and the wall 4 Tighten all bolts Pull the plate away from the wall to help tighten the bolts USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET You need to drill
7. ATION FOR 2 ADDITIONAL EVENLY SPACED TOGGLE BOLTS IN THE MOUNTING PLATE I AREA Part No 316902912 I J C LB i 7 A TY i r3 rai C O i C IAN O O O O O O OD O O O O O O O O OC O O O O A iO gt oO O O O C C b O O Cy C3 Q A oe O O M m e AB udi eos go co er od S us a a a a a a m 13 3 8 2 cx ze E 13 3 8 8 1 4 Tae 25 ao w A m5 t vores ror ror cae vorum vor cae C i de PO DRILL ai yj z sj DIAMETER 3 8 E 7 ren 3 8 3 Pros NL CV I NOTE ITIS VERY IMPORTANT TO READ AND FOLLOW THE DIRECTIONS IN THE INSTALLATION INSTRUCTIONS BEFORE PROCEEDING WITH THS TOP CABINETTEMPLATE This template is used to locale the power cor clearance hole cabinet mounting holes and the vertcal exhaust culout Determine i your cabinet hasa 2 Dil 3 8 diameter holes at A B 6 O P ABI N E EM PLA E recessed area ora smooth fat CLUR ORG Weer sais dedic e bottom Seer 1 If smooth tpe Shing holes nthe cabine otim high 2 titi recessed cut the edges 3 Cut out the 2 diameter hole at D M Sithe template tot inthe recessed for power cord I cabinets are meta fa Boom at fne cabinet its mporant Vae the yon grommet see he Pars z B ivelinoaision ofthe men P Itong surround he opening D POWER CORD Es E NOTE On some cabinets a amet ieee ners ERAS GNEE E E bracket or gue block s used between Apipi g the overh
8. Installation Instructions BEFORE YOU BEGIN Read these instructions completely and carefully Note to Consumer Keep these instructions for future reference IMPORTANT Save these Skill level Installation of this appliance requires instructions for local inspector s use basic mechanical and electrical skills l M PO RTAN T Observe all Proper installation is the responsibility of the installer governing codes and ordinances Product failure due to improper installation is not e Note to Installer Be sure to leave these covered under the Warranty instructions with the Consumer J READ CAREFULLY KEEP THESE INSTRUCTIONS p n 316902904 April 2012 Installation Instructions CONTENTS General information Important Safety Instructions Electrical Requirements Damage Shipment Installation Parts Included Tools You Will N eed Mounting Space Step by step installation guide Placement of The Mounting Plate Removing the Mounting Plate Finding the Wall Studs Determining Wall Plate Location Aligning the Wall Plate Installation T ypes H ood Exhaust A Outside Top Exhaust Attach Mounting Plate to Wall Preparation of Top Cabinet Adapting Microwave Blower for Outside top Exhaust Checking for Proper Damper Operation Mount the Microwave O ven Adjust the Exhaust Adaptor Connecting Ductwork B Outside Back Exhaust Preparing Rear Wall for Outside Back Exhaust Remove Blower Pla
9. ONLY The following chart describes an example of one possible ductwork installation EQUIVALENT NUMBER EQUIVALENT DUCT PIECES LENGTH USED LENGTH Roof Cap 24 Ft 7 3 m 24 Ft 7 3 m 12 Ft 3 6 m Straight Duct 12 Ft 3 6 m 12 Ft 3 6 m 6 15 2 cm Round Rectangular to Round 5 Ft 1 5 m 5 Ft 1 5 m Transition Adaptor Equivalent lengths of duct pieces are based on actual tests and reflect requirements for good venting performance with any vent hood Total Length IMPORTANT If a rectangular to round transition adaptor is used the bottom corners of the damper will have to be cut to fit using the tin snips in order to allow free movement of the damper OUTSIDE BACK EXHAUST EXAMPLE ONLY The following chart describes an example of one possible ductwork installation ee 7 as NUMBER EQUIVALENT haee PIECES LENGTH USED LENGTH 40 Ft 12 2 m 40 Ft 12 2 m 3 Ft Straight Duct 3 Ft 0 9 m 3 Ft 0 9 m 3Y4 x 10 8 2 x 25 4 cm Rectangular 90 Elbow 10 Ft 3 m 20 Ft 3 m Equivalent lengths of duct pieces are based on actual tests and reflect requirements for good venting performance with any vent hood Total Length NOTE For back exhaust care should be taken to align exhaust with space between studs or wall should be prepared at the time it is constructed by leaving enough space between the wall studs to accommodate exhaust Installation Instructions A OUTSIDE TOP EXHAUST vertical Duc
10. ang and the underside of the cabinet bottom Cut the template t fit around the bracket or glue block so that template villis fat against the bottom of te cabinet Tape the Top Cabinet Template to the underside of the top cabinet in the recessed area Fig 3 NOTE Make sure the rear of the template touches the back wall for smooth flat bottom cabinets or the back of the recess for recessed bottom cabinets after cutting the edges of the template cabinet bottom for Vertical Outside Exhaust location 5 Remove the top cabinet template 6 For recessed cabinets make 2 filer blacks out of serap wood the size of the shaded areas F amp G blocks must have a thickness equal to the depth of the cabinet recess Dril diameter holes in these blocks to Ine up with A amp G Place the blocks so that the holes in each block line up withthe corresponding holes in the cabinet The These flor filer blocks should be at the same level DRILL E CUT OUT FOR VERTICAL OUTSIDE EXHAUST ONLY w DIAMETERZ CUT HOLE THROUGH CABINET BOTTOI FOR EXHAUST ADAPTOR as the bottom edge of the wall cabinet frame Fig 4 7 RETURN TO AND PROCEED WITH THE INSTALLATION INSTRUCTIONS WALL Part No 316902475 4 1 2 6 1 4 4 1 12 1 2 24 WALL Printed in China
11. arge enough for the power cord to fit through Read the instructions on the TOP CABINET TEMPLATE Tape it underneath the top cabinet Drill the holes following the instructions on the TOP CABINET TEMPLATE CAUTION Wear safety goggles when drilling holes in the cabinet bottom ADAPTING MICROWAVE BLOWER FOR OUTSIDE BACK EXHAUST Remove and save screw that holds blower motor to microwave Blower M otor Back of Microwave n eg Blower Motor Screw Carefully pull out the blower unit The wires will extend far enough to allow you to adjust the blower unit Before Fan Blade Openings Facing Installation Instructions ADAPTING MICROWAVE 7 Place the blower unit back into the opening BLOWER FOR OUTSIDE AFTER Fan Blade BACK EXHAUST cont Openings Facing Back Roll the blower unit 90 Before Rotation After Rotation Z unit wiring Make sure the wires are not Back of Back of pinched and that they are properly secured Microwave M icrowave NOTE The blower unit exhaust Rotate blower unit counterclockwise 180 openings should match exhaust l l openings on rear of microwave oven Before Rotation After Rotation Secure the blower unit to the microwave with the original screw Blower Plate Back of M icrowave M icrowave M icrowave Blower M otor Gently remove the wires from the grooves Reroute the wires through grooves o
12. box should be located in the cabinet above the microwave oven The outlet box and supply circuit should be installed by a qualified electrician and conform to the National Electrical Code or the prevailing local code Installation Instructions DAMAGE SHIPMENT PARTS INCLUDED conr INSTALLATION eif the unit is damaged in shipment return the unit to the store in which it was bought for repair or replacement eif the unit is damaged by the customer repair or replacement is the responsibility of the customer eif the unit is damaged by the installer if other than the customer repair or replacement must be made by arrangement between customer and installer ADDITIONAL PARTS Installation INSTAL Instructions PARTS INCLUDED nro HARDWARE PACKET ae QUANT Wood Screws Separatel i x 2 Packed Toggle Bolts and Mr wing nuts 346 x 3 Filters Self Aligning M achine Screws 4 28 x 34 Nylon Grommet for metal cabinets Turntable You will find the installation hardware contained in Ring a packet with the unit Check to make sure you have all these parts NOTE Some extra parts are included TY 1 1 1 1 2 1 1 1 2 1 Installation Instructions TOOLS YOU WILL NEED J _ A Ruler or tape measure and FOPIOPIOPOPOPEOPOROPOPOUEEN Pencil 9 straight edge 1 Phillips screw driver enci An Carpenter square optional Tin snips damper if require
13. d Scissors to cut template if necessary Electric drill with 716 Y and 6 drill bits Filler blocks or scrap wood pieces if needed for top cabinet spacing used on recessed bottom WI cabinet installations only Gloves UO Safety goggles Saw saber t or keyhole If finder or Hammer optional Duct and masking tape MOUNTING SPACE The space between the cabinets must be 30 76 2 cm wide and free of obstructions Bottom Edge of f f Cabinet Needs to If you are going to vent your microwave oven be 30 76 2 cm to the outside see H ood Exhaust Section for or M ore from the exhaust duct preparation Cooking Surface 13 Maximum 33 cm Ti 17 43 5 cm 30 76 2 cm pee m regen LL instructions on the top cabinet template for pe ble Backsplash power cord clearance When installing the microwave oven beneath smooth flat cabinets be careful to follow the 66 167 6 cm or More from the Floor to the Top of the Microwave 13 3 4 34 9cm min Installation Instructions 1 PLACEMENT OF THE MOUNTING PLATE REMOVING THE MICROWAVE FINDING THE WALL STUDS OVEN FROM THE CARTON REMOVING THE MOUNTING PLATE Remove the installation instructions filters glass tray and the small hardware bag Do not remove the Styrofoam protecting the front of the oven Fold back all 4 carton flaps fully aga
14. e Tape the Rear Wall al Template onto the wall Draw a vertical line on the wall at the center of the 30 space EE Dion anne Tape the Rear Wall Template onto the wall bottom of the cabinet rs the centerline and touching the bottom binet frame iii Your cabinets may have decorative trim that Plate position beneath recessed interferes with the microwave installation Remove bottom cabinet with front overhang the decorative trim to install the microwave properly and to make it level Draw a line on the THE MICROWAVE MUST BE LEVEL back wall equal to the Use a level to make sure the cabinet bottom is level un SIS If the cabinets have a front overhang only with no Hid back or side frame install the mounting plate down the same distance as the front overhang depth This will keep the microwave level Measure the inside depth of the front overhang Draw a horizontal line on the back wall an equal distance below the cabinet bottom as the inside depth of the front overhang For this type of installation with front overhang only align the mounting tabs with this horizontal line not touching the cabinet bottom as described in Step D Installation Instructions ALIGNING THE WALL PLATE il F CUT OUT FOR HORIZONTAL OUT SIDE EXHAUST walls REAR WALLITEMPLATE Centerline notches Draw a V j on Wall from Center of Top Cabin
15. e mounted to BOTH a top cabinet AND a wall NOTE For easier installation and personal safety it is recommended that two people install this product IMPORTANT PLEASE READ CAREFULLY FOR PERSONAL SAFETY THIS APPLIANCE MUST BE PROPERLY GROUNDED TO AVOID SEVERE OR FATAL SHOCK The power cord of this appliance is equipped with a three prong grounding plug which mates with a standard three prong grounding wall receptacle to minimize the possibility of electric shock hazard from this appliance Ensure proper ground exists before use You should have the wall receptacle and circuit checked by a qualified electrician to make sure the receptacle is properly grounded Where a standard two prong wall receptacle is encountered it is very important to have it replaced with a properly grounded three prong wall receptacle installed by a qualified electrician DO NOT UNDER ANY CIRCUMSTANCES CUT DEFORM OR REMOVE ANY OF THE PRONGS FROM THE POWER CORD DO NOT USE WITH AN EXTENSION CORD ELECTRICAL REQUIREMENTS Product rating is 120 volts AC 60 H ertz 15 amps and 1 6 kilowatts This product must be connected to a supply circuit of the proper voltage and frequency Wire size must conform to the requirements of the National Electrical Code or the prevailing local code for this kilowatt rating The power supply cord and plug should be brought to a separate 15 to 20 ampere branch circuit single grounded outlet The outlet
16. e opening following the instructions of the REAR WALL TEMPLATE 16 REMOVE BLOWER PLATE Remove and save the screw that holds the blower plate to the microwave Lift off the blower plate Blower Plate e Back of Microwave Installation Instructions ATTACH THE MOUNTING PLATE TO THE WALL Attach the plate to the wall using toggle bolts At least one wood screw must be used to attach the plate to a wall stud 1 Remove the toggle wings from the bolts 2 Insert the bolts into the mounting plate through the holes designated to go into drywall and reattach the toggle wings to 19 mm onto each bolt To use toggle bolts Spacing for Toggles M ore Than Wall Thickness iToggle Wings Mounting I ua Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount the plate NOTE Before tightening toggle bolts and wood screw make sure the tabs on the mounting plate touch the bottom of the cabinet when pushed flush against the wall and that the plate is properly centered under the cabinet CAUTION Be careful to avoid pinching fingers between the back of the mounting plate and the wall 4 Tighten all bolts Pull the plate away from the wall to help tighten the bolts 17 USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET You need to drill holes for the top support screws and a hole l
17. et sd o o o 0 000p Oo O O O O O O O O C O O O O O O p E o a aca 0 0 0l0 o 0 a a arang Q oooo00 Horizontal Line Area E CAUTION Wear gloves to avoid cutting fingers on sharp edges Draw a Vertical line on the wall atthe center of the 30 wide space Draw a Horizontal line on the wall at the bottom of Rear Wall Template Drill 5 8 holes for toggle bolts on 2 locations Hole A Hole B but if the location of hole is same as that of stud drill a 3 16 hole for wood screw In other words toggle bolt can not be used to the location of stud NOTE DO NOT MOUNT THE PLATE AT THIS TIME Hole A Horizontal Line Draw a Horizontal line on wall from bottom of Rear Wall Template NOTE Holes A andB are inside area E If both of A and B are not in a stud find a stud somewhere in area E and draw a forth circle to line up with the stud It is important to use at least one wood screw mounted firmly in a stud to support the weight of the microwave Set the mounting plate aside Installation Instructions INSTALLATION TYPES choose A B or C This microwave oven is designed for adaptation to NOTE This microwave is shipped assembled for the following three types of ventilation Fecirculating Select the type of ventilation required A Outside Top Exhaust Vertical Duct for your installation and proceed to that section B Outside Back Exhaust Horizontal Duct C Recirculating Non Vented Ductless
18. gh top center cabinet hole Temporarily secure the oven by turning the screw at least two full turns after the threads have engaged It will be completely tightened later Be sure to keep power cord tight Be careful not to pinch the cord especially when mounting flush to bottom of cabinet Cabinet Front Cabinet Bottom Shelf Filler Block Equivalent to Depth of Cabinet Recess M icrowave Oven Top Attach the microwave oven to the top cabinet Installation Instructions MOUNT THE MICROWAVE OVEN cont 5 Insert 2 self aligning screws through outer top cabinet holes Turn two full turnson each screw Tighten center screw completely Tighten the outer two screwsto the top of the microwave oven While tightening screws hold the microwave oven in place against the wall and the top cabinet packed with Install grease filters See the Owner s Manual the microwave 22 INSTALLING OR CHANGE THE CHARCOAL FILTER NOTE The charcoal filter isfactory installed in recirculating models Follow these steps to replace a filter or to install a filter after converting a vented model to recirculating operation 1 Remove screws on top of grille using a 1 Phillips screwdriver 2 Open the door 3 Remove the grille Pull the grille straight off
19. he left or i right side of the centerline NOTE Itis important to use at least one wood l screw mounted firmly in a stud to support the weight of the microwave Mark two additional evenly spaced locations for the supplied toggle bolts 3 Drill holes in the marked locations Where there is f a stud drill a 3 16 hole for wood screws For holes that do not ine up with a stud drill 8 holes for toggle bolts l NOTE DO NOT INSTALL THE MOUNTING PLATE AT THIS TIME 4 Remove the template from the rear wall 5 Review the Installation Instruction book for your installation situation l Darle vuelta a la hoja para consultar la versi n en Espa ol at TO EDGE 12 F CUT OUT FOR HORIZONTAL OUTSIDE EXHAUST CUT HOLE THROUGH REAR WALL FOR EXHAUST ADAPTOR CAUTION IF EXHAUST ADAPTOR IS POSITIONED OUTSIDE RECOMMENDED DIMENSION GREASE LADEN AIR WILL DISCHARGE INTO HOUSE STRUCTURE Locate and mark holes to align with holes in the mounting plate IMPORTANT LOCATE AT LEAST ONE STUD ON EITHER SIDE OF THE CENTERLINE MARK THE LOCATION FOR 2 ADDITIONAL EVENLY SPACED TOGGLE BOLTS IN THE MOUNTING PLATE AREA l i Trim the rear wall template along the dotted line 30 MINIMUM WIDTH REQUIRED REAR WALL TEMPLATE Locate and mark holes to align with holes in the mounting plate IMPORTANT LOCATE AT LEAST ONE STUD ON EITHER SIDE OF THE CENTERLINE MARK THE LOC
20. inch cord or lift oven by pulling cord Lift microwave tilt it forward and hook slots at back bottom edge onto four lower tabs of mounting Rotate front of oven up against cabinet bottom Insert a self aligning screw through top center cabinet hole Temporarily secure the oven by turning the screw at least two full turns after the threads have engaged It will be completely tightened later Be sure to keep power cord tight Be careful not to pinch the cord especially when mounting flush to bottom of cabinet 19 Cabinet Front SJ Cabinet Bottom Shelf Filler Block Equivalent to Depth of Cabinet Recess Self Aligning Screw Microwave Oven Top Attach the microwave oven to the top cabinet 5 Insert 2 self aligning screws through outer top cabinet holes Turn two full turns on each screw Tighten center screw completely Tighten the outer two screws to the top of the microwave oven While tightening screws hold the microwave oven in place against the wall and the top cabinet Install grease filters See the Owner s Manual packed with the microwave Installation Instructions RECIRCULATING Non Vented Ductless INSTALLATION OVERVIEW C1 Attach Mounting Plate to Wall C2 Prepare Top Cabinet C3 Check Blower Plate C4 Mount the Microwave O ven C5 Install or change Charcoal Filter IMPORT
21. ing Top Microwave CAUTION Do not pull or stretch the blower unit wiring Make sure the wires are not pinched and that they are properly secured Installation Instructions ADAPTING MICROWAVE BLOWER FOR OUTSIDE TOP EXHAUST Secure blower unit to microwave with the screw removed in Step 1 Make sure the screw is tight Replace blower plate with the screw removed in Step 1 Make sure the screw is tight Back of Microwave Attach the exhaust adaptor to the top of the blower plate by sliding it into the guides of the blower plate Adaptor Guide Back of Microwave Locking Tab Push in securely until it isin the locking tabs Take care to assure that the damper hinge is installed so that the damper swings freely CHECK FOR PROPER DAMPER OPERATION Blower Plate Exhaust Adaptor ad m Damper 88 Back of mic rowave Make sure tape securing damper is removed and damper pivots easily before mounting microwave You will need to make adjustments to assure proper alignment with your house exhaust duct after the microwave is installed 14 MOUNT THE MICROWAVE FOR EASIER INSTALLATION AND PERSONAL SAFETY WE RECOMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN IMPORTANT Do not grip or use handle during installation NOTE If your cabinet is metal use the nylon grommet around the power cord hole to prevent cutting of the cord NOTE We recommend us
22. ing filler blocks if the cabinet front hangs below the cabinet bottom shelf IMPORTANT If filler blocks are not used case damage may occur from overtightening screws NOTE When mounting the microwave oven thread power cord through hole in bottom of top cabinet Keep it tight throughout Steps 1 3 Do not pinch cord or lift oven by pulling cord Lift microwave tilt it forward and hook slots at back bottom edge onto four lower tabs of mounting plate Rotate front of oven up against cabinet bottom Insert a self aligning screw through top center cabinet hole Temporarily secure the oven by turning the screw at least two full turns after the threads have engaged It will be completely tightened later Be sure to keep power cord tight Be careful notto pinch the cord especially when mounting flush to bottom of cabinet Installation Instructions MOUNT THE MICROWAVE OVEN cont Cabinet Front Cabinet Bottom Shelf Filler Block Equivalent to Depth of Cabinet Recess UU Self Aligning Screw Microwave Oven Top Attach the microwave oven to the top cabinet Insert 2 self aligning screws through outer top cabinet holes Turn two full turnson each screw Tighten center screw completely Tighten the outer two screws to the top of the microwave oven While tightening screws hold the microwave
23. inst carton sides Then carefully roll the oven and carton over onto the top side The oven should be resting in the Styrofoam Center Find the studs using one of the following methods A Stud finder a magnetic device which locates nails OR Styrofoam B Usea hammer to tap lightly across the x mounting surface to find a solid sound This will indicate a stud location After locating the stud s find the center by probing the wall with a small nail to find the edges Pull the carton up and off the oven of the stud Then place a mark halfway between the edges The center of any adjacent studs should Cutthe middle of the outer protective plastic bag to be 16 40 6 cm or 24 61 cm from this mark remove the mounting plate 3 Draw a line down the center of the studs Screws Screws THE MICROWAVE MUST BE CONNECTED TO AT LEAST ONE WALL STUD Y Mounting Plate T Remove the screws from the mounting plate This plate will be used asthe rear wall template and for mounting Reinstall the screws into the holes where they were removed Installation Instructions DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET Plate position beneath flat bottom Plate position beneath framed cabinet recessed cabinet bottom Draw a vertical line on the wall at the center of 33 to Cooktop the 30 wide spac
24. n other side of the blower unit Before Rerouting After Rerouting Replace the blower plate in the same position as before with the screw M ake sure the screw is tight Attach the exhaust adaptor to the rear of the oven by sliding it into the guides at the top center of the back of the oven W ires Routed Through Right Side Wires Routed Through Left Side Adaptor Roll the blower unit 90 so that fan blade openings are facing out the back of the microwave Before Rolling After Rolling cking Tabs Push in securely until itisin the lower locking Back of tabs Take care to assure that the damper hinge one is installed so that it is at the top and that the Back of M icrow ave d freel Microwave amper swings freely 18 Installation Instructions MOUNT THE MICROWAVE FOR EASIER INSTALLATION AND PERSONAL SAFETY WE RECOMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN IMPORTANT Do not grip or use handle during installation NOTE If your cabinet is metal use the nylon grommet around the power cord hole to prevent cutting of the cord NOTE We recommend using filler blocks if the cabinet front hangs below the cabinet bottom shelf IMPORTANT If filler blocks are not used case damage may occur from overtightening screws NOTE When mounting the microwave oven thread power cord through hole in bottom of top cabinet Keep it tight throughout Steps 1 3 Do not p
25. ng is blocking the ducts duct length add the equivalent lengths of all transitions and adaptors plus the length of all straight duct sections Exhaust connection The chart below shows you how to calculate total The exhaust adaptor has been designed to mate with equivalent ductwork length using the approximate feet a standard 3 4 x 10 8 2 x 25 4 cm rectangular duct of equivalent length of some typical ducts If a round duct is required a rectangular to round transition adaptor must be used A 5 10 5cm 6 15 2cm diameter duct is acceptable to use EQUIVALENT NUMBER EQUIVALENT DUCT PIECES LENGTH USED LENGTH Rectangular to Round 5 Ft 1 5 m Transition Adaptor 90 Elbow 10 Ft 3 m 45 Elbow 5 Ft 1 5 m Roof Cap 24 Ft 7 3 m Straight Duct 6 15 2 cm 1 Ft 0 3 m Round or 3Y4 x 10 8 2 x 25 4 cm Rectangular IMPORTANT If arectangular toround transition Equivalent lengths of duct pieces are based on actual tests gt adaptor is used the bottom corners of the damper and reflect requirements for good venting performance with Gr m T Total Ductwork will have to be cut to fit using the tin snips in order any vent hood to allow free movement of the damper Installation Instructions EXTERNAL EXHAUST DUCTING NOTE Read these next two pages only if you plan to vent your exhaust to the outside If you plan to recirculate the air back into the room proceed to page 20 OUTSIDE TOP EXHAUST EXAMPLE
26. t INSTALLATION OVERVIEW A1 Attach Mounting Plate to Wall A2 Prepare Top Cabinet A3 Adapting Microwave Blower for Outside Top Exhaust A4 Check Damper Operation A5 Mount Microwave O ven A6 Adjust Exhaust Adaptor A7 Connect Ductwork IMPORTANT NOTES Make sure the screws for the blower motor and blower plate are securely tightened when they are reinstalled This will help to prevent excessive vibration Make sure the motor wiring has been properly routed and secured and that the wires are not pinched ATTACH THE MOUNTING PLATE TO THE WALL Attach the plate to the wall using toggle bolts At least one wood screw must be used to attach the plate to a wall stud 1 Remove the toggle wings from the bolts 2 Insert the bolts into the mounting plate through the holes designated to go into drywall and reattach the toggle wings to 4 19 mm onto each bolt 12 To use toggle bolts Spacing for Toggles More Than Wall gt i lt Thickness i Toggle Wings Mounting NH j Toggle Bolt End Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount the plate NOTE Before tightening toggle bolts and wood screw make sure the tabs on the mounting plate touch the bottom of the cabinet when pushed flush against the wall and that the plate is properly centered under the cabinet
27. te Attach Mounting Plate to Wall Preparation of Top Cabinet Adapting Microwave Blower for Outside Back Exhaust Mount the Microwave O ven Recirculating Attach Mounting Plate to Wall Preparation of Top Cabinet Check Blower Plate Mount the Microwave O ven Installing or Change the Charcoal Filter Before You U se Your Microwave Template Information Installation Instructions IMPORTANT SAFETY INSTRUCTIONS This product requires a three prong grounded outlet The installer must perform a ground continuity check on the power outlet box before beginning the installation to insure that the outlet box is properly grounded If not properly grounded or if the outlet box does not meet electrical requirements noted under ELECTRICAL REQUIREMENTS a qualified electrician should be employed to correct any deficiencies CAUTION For personal safety remove house fuse or open circuit breaker before beginning installation to avoid severe or fatal shock injury CAUTION For personal safety the mounting surface must be capable of supporting the cabinet load in addition to the added weight of this 63 85 pound 28 5 38 5 kg product plus additional oven loads of up to 50 pounds 22 7 kg or a total weight of 113 135 pounds 51 3 61 2 kg CAUTION For personal safety this product cannot be installed in cabinet arrangements such as an island or a peninsula It must b
Download Pdf Manuals
Related Search