Waring Pro WPM40TR Use and Care Manual
Contents
1. WARING PRO PROFESSIONAL POPCORN MAKER WPM40 Series For your safety and continued enjoyment of this product always read the instruction book carefully before using IMPORTANT SAFEGUARDS When using any electrical appliance basic safety precau tions should always be followed including the following 1 READ ALL INSTRUCTIONS BEFORE USING YOUR POPCORN MAKER 2 Unplug main power cord from outlet while not in use and before cleaning 3 To avoid any risk of electrical shock do not immerse cord or plug into water or other liquid 4 This appliance should not be used by or near children or individuals with certain disabilities 5 Do not touch hot surfaces Always use handles or knobs to operate 6 Allow Hot parts to cool down before maneuvering 7 Do not operate the appliance with damaged cord or plug or after the appliance malfunctions or has been damaged in any matter Send the unit to the nearest authorized service center for examination repair or adjustment ONLY technicians should open up the unit 8 The use of any accessories or attachments not recommended by the manufacturer may cause injury 9 Donot pop the kernels with a dry kettle without oil 10 Do not immerse popping kettle into water 11 Kettle surface is HOT and should NOT be touched during popping or just after use 12 Unplug allow to cool clean and cover t2. immediately turn POP switch to the Off position and rotate the roller bar of the kettle down to release any remaining popcorn in the popper This will also stop the remaining popcorn from cooking any further and avoid possible burning The light warmer switch may be left in the On position 12 Keep POP switch Off if the unit is not continuously in use 13 Keep only the light warmer switch on 14 Remove plug from power supply if the unit is not being used 15 Repeat steps 7 to 10 for continuous popping CLEANING AND MAINTENANCE It is strongly recommended to clean the kettle frequently to avoid burning excess oil onto the bottom of the inner pot After using the popcorn machine use a wet cloth to clean the main unit main body and glass It is strongly recommended to wash and dry the tray after each use to avoid any bacteria buildup LIGHT WARMER The light warmer bulb can be replaced with a 120V 60W maximum bulb only QUICK CLEANING PROCEDURE Turn the POP control to Off Pour 5 to 8 ounces of water NO detergent is necessary into inner pot Switch to On to boil the water and let the stirrer turn in order to remove excess oil stuck on the surface Pour out the water into a deep bowl and discard after about 1 to 2 minutes of boiling CAUTION THE KETTLE IS HOT Or remove the kettle and clean it with a Scotch Brite scouring pad Do not immerse kettle or electrical plug in water Any other trademarks or service
3. he unit and store in a dry and safe place if not being used for a long time 13 Do not let power cord hang over edge of table or counter or touch any hot surfaces 1 21 22 23 24 Do not place the unit on or near a hot gas or electric burner or in a heated oven Extreme caution must be paid when moving the appliance containing hot oil or other hot liquids Turn ALL switches to OFF position before disconnecting power plug from the wall supply outlet Not recommended for outdoor use Do not use appliance for other than intended use To avoid overheating always add oil and then kernels before operating Extreme caution must be used when unloading popcorn Always place the unit over a countertop so that residual hot oil or water running out will not cause burns KEEP OUT OF REACH OF CHILDREN DO NOT CLEAN USING ANY ABRASIVE MATERIAL NEVER FORCE ANY PARTS OR BRACKETS INTO POSITION NO PARTS ARE INTENDED FOR THE DISHWASHER SAVE THESE INSTRUCTIONS FOR HOUSEHOLD USE ONLY Ae Sf oN Housing Kettle Gear Box Kettle Lid Axle Fixer Stirrer Retaining Pin 10 11 12 13 D Pin Light Warmer Door Door Panel removable Tray removable Measuring Spoons and Scoops ASSEMBLING PROCEDURE FIGURE 1 Screw the kettle lid axle fixer and stirrer onto the gear box FIGURE 2 Hold the kettle on the supporter FIGURE 4 FIGURE 3 Use the retaining pin to fix Insert the pin t
4. hrough the kettle at the right position kettle and supporter FIGURE 5 Finally insert the internal kettle plug into the socket on the inner top of the popcorn maker housing POPPING INSTRUCTIONS 1 2 10 Make sure the popcorn maker is unplugged before you do any of the following Before using the unit please check carefully if voltage 120V 60 Hz is suitable to your home Clean the internal surface of the kettle with warm sudsy water rinse well and dry with a clean cloth Wipe down inner and outer housing with damp cloth Main unit has 2 function switches as follows Light warmer combination POP switch to turn heater and stirrer on Hook the kettle onto the hanger of the main unit Plug the power cord into an electric outlet Insert the internal plug into the socket See figure 5 previous page Turn the light switch to the On position and the POP switch to the On position The stirrer will begin to rotate in the kettle Let the stainless steel kettle preheat about 3 to 4 minutes Open lid and add oil 1 tablespoon of vegetable corn peanut or safflower oil Immediately add 12 cup of corn kernels and close lid to the kettle Caution Lid might be hot it is recommended to use an oven mitt Popcorn starts popping out through the lid after about 2 minutes Yields up to 12 cups per batch in less than 2 2 minutes When unit is finished popping you will no longer hear the corn popping
5. marks of third parties herein are the trademarks or service marks of their respective owners 2009 Waring Products Division of Conair Corporation 150 Milford Road East Windsor NJ 08520 www waringpro com Printed in China WPM4O IB O9WR13126
Download Pdf Manuals
Related Search