none ACT-NBDB-5HSPB Instructions / Assembly
Contents
1. 2x 18 mm 1 x 29mm Wooden amp Metal Screws Batteries 1 Fixing Plate NextBolt User Manual 4 For support contact us a 1 800 408 7101 ext 102 Actuator Systems http www advancedactuators com 2 Required Tools With the EZ Mount Kit Installation is quick and easy If your door has an existing deadbolt you only need the following tools 4 Philips amp flat head screw drivers 3 Pre installation 3 1 Mark and bore holes on the door 3 11 Mark holes on door For doors with existing deadbolt lock with 2 1 8 diameter hole 1 Remove existing cylindrical deadbolt NextBolt User Manual 5 For support contact us a 1 800 408 7101 ext 102 Actuator Systems http www advancedactuators com 2 Please be sure to use the included clear installation template when installing the Actuator Systems NextBolt on a door with an existing deadbolt 3 Rest the installation template on the front of the door on top of the existing 2 1 8 hole making sure that it is aligned properly for the door s existing 2 3 8 or 2 34 backset NextBolt User Manual 6 For support contact us a 1 800 408 7101 ext 102 Actuator Systems http www advancedactuators com For doors that do not have a cylindrical deadbolt lock or a hole for the cylindrical deadbolt lock A Start approximately 46 from floor Select the appropria2. Actuator Systems http www advancedactuators com PREFACE gt Thank you for purchasing the Actuator Systems NextBolt fingerprint deadbolt gt Please read the documentation carefully before installation amp use The manual details all installation procedures and operation steps gt Manufacturer and or Distributors of the Actuator Systems NextBolt will not be responsible for any damages caused by incorrect installation or mishandling of the lock Any such damages will void manufacturer s warranty NextBolt User Manual 1 For support contact us a 1 800 408 7101 ext 102 Actuator Systems http www advancedactuators com Table of Contents sates ans ates Esclat tac Installation Manual 2 WRB ins il RERE 3 1 Mark and bore holes on the 3 2 Deadbolt Latch 4 Installation ccccccececececeseseseseseseseseseseseseseseseseseseseseseseeesees 4 1 Installation of Deadbolt 0 eeeeeeeeeeeeeeeeeeee 4 2 Installing Strike and Strike Lining Box on the door ease eee 4 3 Sizing Tail Piece to the right lengtb 4 4 Installation of the Outdoor 7 4 5 Installation of the Indoor Trouble SUGO Li ca Ope
3. The first two fingerprint users enrolled will automatically be programmed as ADMINISTRATORS Users 1 and 2 ADMINISTRATORS can apply all programming functions as well as verify their fingerprints to unlock the door The 3rd thru 99th fingerprint users enrolled Users 3 thru 99 are automatically programmed at the USER level USER level fingerprints can only be used to unlock the door not to program the lock Section I Enrolling Administrators First Fingerprint User Sliding cover must be closed before any programming sequence can begin As noted in the Helpful Hints section the first two users that enroll their fingerprints into the Actuator Systems NextBolt will automatically be programmed as ADMINISTRATORS Users 1 and 2 ADMINISTRATORS can apply all programming functions as well as verify their fingerprints to unlock the door Please use the following steps to enroll the first fingerprint user ADMINISTRATORI USER 1 e Remove the battery cover from the indoor unit e Press the ADD button located on the indoor unit e Single beep will be heard NextBolt User Manual 29 For support contact us a 1 800 408 7101 ext 102 Actuator Systems http www advancedactuators com e Fully open the sliding cover located on the outdoor unit immediately e Sensor will flicker for less than one second e A single short beep will be heard and the fingerprint sensor will power on e After the fingerprint sensor pow
4. Trouble Shooting PROBLEMS POSSIBLE SOLUTIONS REASONS Indoor turn knob 1 Incorrect Make sure the tail piece was does not turn or installation inserted vertically through turns very the cross slot of the deadbolt sluggishly and slot of the indoor unit while the turn knob was vertical facing down Measure the door thickness 2 Incorrect and swap or trim the tail tailpiece length piece per section 4 3 of the installation manual NextBolt User Manual 23 For support contact us a 1 800 408 7101 ext 102 i Actuator P Systems Indoor turn Enob turns but nothing happens The tail piece did not go through the cross slot of the deadbolt Tail piece was trimmed too short and does not penetrate the slot of the indoor unit 1 http www advancedactuators com Remove and reinstall the outdoor unit Then insert the tail piece through the cross slot of the deadbolt and slot of the indoor unit while the turn knob is in vertical position facing down Contact the Actuator Systems NextBolt dealer that you purchased to lock from OR Contact us at support advancedactuators com The sliding cover is fully lifted to power on without any fingerprint enrolled inside the deadbolt does not Right amp left hand door configurations is set incorrectly Correctly configure the unit for left or right hand door swing per section 4 5 Uninstall the outdoor unit and keep the UP sign side of dis
5. ADD ADD DEL 39 ADD DEL DEL ADD ADD ADD 40 ADD DEL ADD DEL DEL DEL 41 ADD DEL ADD DEL DEL ADD 42 ADD DEL ADD DEL ADD DEL 43 ADD DEL ADD DEL ADD ADD 44 ADD DEL ADD ADD DEL DEL 45 ADD DEL ADD ADD DEL ADD 46 ADD DEL ADD ADD ADD DEL 47 ADD DEL ADD ADD ADD ADD 48 ADD ADD DEL DEL DEL DEL 49 ADD ADD DEL DEL DEL ADD 50 ADD ADD DEL DEL ADD DEL 51 ADD ADD DEL DEL ADD ADD 52 ADD ADD DEL ADD DEL DEL 53 ADD ADD DEL ADD DEL ADD 54 ADD ADD DEL ADD ADD DEL 55 ADD ADD DEL ADD ADD ADD 56 ADD ADD ADD DEL DEL DEL NextBolt User Manual 45 For support contact us a 1 800 408 7101 ext 102 Actuator Systems 57 http www advancedactuators com ADD ADD ADD DEL DEL ADD 58 ADD ADD ADD DEL ADD DEL 59 ADD ADD ADD DEL ADD ADD 60 ADD ADD ADD ADD DEL DEL 61 ADD ADD ADD ADD DEL ADD 62 ADD ADD ADD ADD ADD DEL 63 ADD ADD ADD ADD ADD ADD 64 ADD DEL DEL DEL DEL DEL DEL 65 ADD DEL DEL DEL DEL DEL ADD 66 ADD DEL DEL DEL DEL ADD DEL 67 ADD DEL DEL DEL DEL ADD ADD 68 ADD DEL DEL DEL ADD DEL DEL 69 ADD DEL DEL DEL ADD DEL ADD 70 ADD DEL DEL DEL ADD ADD DEL 71 ADD DEL DEL DEL ADD ADD ADD 12 ADD DEL DEL ADD DEL DEL DEL 73 ADD DEL DEL ADD DEL DEL ADD 74 ADD DEL DEL ADD DEL ADD DEL 75 ADD DEL DEL ADD DEL ADD ADD 76 ADD DEL DEL ADD ADD DEL DEL 71 ADD DEL DEL ADD ADD DEL ADD 78 ADD DEL DEL ADD AD
6. Installation of Deadbolt A Insert the deadbolt latch into the hole in the edge of the door follow the UP sign keeping it parallel to the face of the door Mark the outline of the face plate and remove the deadbolt B Then chisel 1 8 deep rectangular shape per your marking or until the faceplate is flush with the door edge MM C Insert the deadbolt latch make sure the deadbolt UP sign is facing upwards Then fasten the screws NextBolt User Manual 9 For support contact us a 1 800 408 7101 ext 102 Actuator Systems http www advancedactuators com 4 2 Installing Strike and Strike Lining Box on the door jamb 1 Close the door until the deadbolt touches the door jamb along the face plate to mark the horizontal center lines 2 Measure one half of the door thickness from one side of the door jamb and then mark the vertical center lines 3 Extend the vertical center line and the horizontal line to mark the drill center point for the strike Bore a 1 diameter and 1 deep hole in the door jamb at the center point for strike To ensure the proper deadbolt function this hole must be drilled at least 1 deep Chisel the door jamb at 1 16 deep for the strike plate which must fit flush with the door jamb Insert the strike lining box and then fasten screws to the plate A A B B D NextB
7. of the Indoor Unit If the door is left handed please push the orientation selector switch to L position if it s right handed switch the selector to R position NextBolt User Manual 16 For support contact us a 1 800 408 7101 ext 102 Actuator Systems http www advancedactuators com 2 Plug wire set into circuit board making sure all prongs are firmly seated Make sure the black dots on the cable and connector align 3 Turn the manual turn knob to the vertical position facing downward NextBolt User Manual 17 For support contact us a 1 800 408 7101 ext 102 Actuator Systems http www advancedactuators com 4 Insert the tail piece into the vertical retaining slot of the indoor unit 5 Gently finish joining the outdoor and indoor units together NextBolt User Manual 18 For support contact us a 1 800 408 7101 ext 102 Actuator Systems http www advancedactuators com 6 Fasten the two shorter 15mm screws through the fixing plate on the upper section of the inside unit NextBolt User Manual 19 For support contact us a 1 800 408 7101 ext 102 Actuator Systems http www advancedactuators com 7 Fasten the two long screws through the bottom fixing post holes on the inside unit 8 Move the manual turn knob back and forth to ensure that deadbolt opens and closes mechanically
8. pads prior to enrollment These dramatically increase the quality of the enrollment Once enrolled these pads may be discarded NextBolt User Manual 27 For support contact us a 1 800 408 7101 ext 102 1 Actuator Systems Always wait until the fingerprint scanner turns on to place your finger on the scanning window This is true for both fingerprint enrollment AND verification http www advancedactuators com When trying to enroll or verify fingerprints in direct sunlight be sure to shade the sensor with your shadow so sunlight will not reflect off of the mirror in the sensor gt CA EL Put the finger center on the i center of the scanner window Place finger flat on the I window Good Bad zel Don t put finger on the l edge and then move to the center lt RS Raise the finger then leave De Da scanning window after fingerprint scanning Don t drag the finger on the surface of the scanning window Important Programming Notes When Adding or Deleting Fingerprints the closed sliding cover must be fully lifted within 8 seconds after pressing the ADD or DEL button or the NextBolt will power off If this occurs simply close the sliding cover press the ADD or DEL button again and fully lift the sliding cover immediately to restart the programming sequence NextBolt User Manual 28 For support contact us a 1 800 408 7101 ext 102 Actuator Systems http www advancedactuators com
9. 02 Actuator Systems http www advancedactuators com e Fully open the sliding cover located on the outdoor unit immediately e Sensor will flicker for less than one second e A single short beep will be heard and the fingerprint sensor will power on e After the fingerprint sensor powers on rest an ADMINISTRATOR S finger on the sensor window to verify that they are an Administrator e When the first Administrator s fingerprint is successfully verified the sensor will briefly turn off for less than one second e Immediately remove the ADMINSTRATOR S finger and enter the KEPRESS SEQUENCE for the user number you wish to enroll described in APPENDIX A NextBolt User Manual 33 For support contact us a 1 800 408 7101 ext 102 Actuator Systems http www advancedactuators com e A single short beep will be heard and the fingerprint sensor will power on e Rest the new user s pointer finger on the sensor window during the first of three scans e Keep your pointer finger on the scanning window until you hear a single long beep or four beeps After the scanning is completed you will hear one of the following o Single long beep indicating that the operation was successful OR o Four beeps indicating that your fingerprint was not successfully enrolled If you hear four beeps please start the enrollment process over from the beginning Once enrollment begins users can be enrolled consecutively wit
10. 1 800 408 7101 ext 102 Actuator Systems http www advancedactuators com With no fingerprints enrolled in the Actuator Systems NextBolt the deadbolt will engage disengage when the sliding cover is fully opened and immediately closed Definitions of Indication Beeps Single Short Beep Indicates that any operations sequence has begun OR that the door has been successfully locked or unlocked OR that the sliding cover has been left open for more than ten seconds Single Long Beep Indicates that programming operation was successful Short Double Beep Indicates that individual fingerprint user deletion sequence has begun Long Double Beep Indicates that Delete All programming was successful Four Beeps Indicates unsuccessful enrollment unsuccessful verification attempt OR Actuator Systems NextBolt was improperly installed see Installation Guide Five Beeps Indicates the selected user was unsuccessfully deleted Six Short Beeps Low battery alert change batteries Common definitions of terms used when using the Actuator Systems NextBolt Fingerprint Enrollment Process of adding fingerprints to the Actuator Systems NextBolt Enrolled Fingerprints Fingerprints that have been successfully added into the Actuator Systems NextBolt NextBolt User Manual 26 For support contact us a 1 800 408 7101 ext 102 5535 Verifying Fingerprints Process of authentication by scanning enrolled fi
11. D ADD DEL 79 ADD DEL DEL ADD ADD ADD ADD 80 ADD DEL ADD DEL DEL DEL DEL 81 ADD DEL ADD DEL DEL DEL ADD 82 ADD DEL ADD DEL DEL ADD DEL 83 ADD DEL ADD DEL DEL ADD ADD 84 ADD DEL ADD DEL ADD DEL DEL 85 ADD DEL ADD DEL ADD DEL ADD 86 ADD DEL ADD DEL ADD ADD DEL 87 NextBolt User Manual ADD DEL ADD DEL ADD ADD ADD 46 For support contact us a 1 800 408 7101 ext 102 Actuator Systems 88 http www advancedactuators com ADD DEL ADD ADD DEL DEL DEL 89 ADD DEL ADD ADD DEL DEL ADD 90 ADD DEL ADD ADD DEL ADD DEL 91 ADD DEL ADD ADD DEL ADD ADD 92 ADD DEL ADD ADD ADD DEL DEL 93 ADD DEL ADD ADD ADD DEL ADD 94 ADD DEL ADD ADD ADD ADD DEL 95 ADD DEL ADD ADD ADD ADD ADD 96 ADD ADD DEL DEL DEL DEL DEL 97 ADD ADD DEL DEL DEL DEL ADD 98 ADD ADD DEL DEL DEL ADD DEL 99 ADD ADD DEL DEL DEL ADD ADD NextBolt User Manual 47 For support contact us a 1 800 408 7101 ext 102 Actuator Systems http www advancedactuators com USER ENROLLMENT TABLE Number Name Finger Used L R Date CO NJ ON My BPO NM 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 21 28 NextBolt User Manual 48 F
12. NextBolt User Manual 20 For support contact us a 1 800 408 7101 ext 102 Actuator Systems http www advancedactuators com 9 Insert 4 high quality AA batteries NextBolt User Manual 21 For support contact us a 1 800 408 7101 ext 102 Qa Systems http www advancedactuators com 10 Press the electronic open close button to ensure that the deadbolt opens and closes electronically 4 6 Final inspection adjustment prior to enrollment Note After installation and prior to using the unit make sure you read and follow the steps below Turn the inside knob to the horizontal position next turn it to the vertical position locked position It should turn freely If and when the inside and outside locks are attached securely and the inside knob doesn t turn freely see the trouble shooting table below for possible solution If the knob turns freely continue with the next step 2 Try to lock and unlock from outside by fully opening and closing the sliding cover 8 Try to lock and unlock from inside by pressing the Open Close button to ensure it works well electronically IMPORTANT SECURITY NOTE WITHOUT ANY FINGERPRINTS ENROLLED THE NextBolt WILL LOCK AND UNLOCK BY FULLY OPENING AND FULLY NextBolt User Manual 22 For support contact us a 1 800 408 7101 ext 102 Actuator Systems CLOSING THE SLIDING COVER http www advancedactuators com 5
13. eld down 3 When one long beep is heard pull the outside cover up and place the Admin finger on the sensor for verification when the sensor light turns on 4 Once one long beep is heard the lock is reset successfully e Close the sliding cover IMPORTANT SECURITY NOTE WITHOUT ANY FINGERPRINTS ENROLLED THE NEXTBOLT WILL LOCK AND UNLOCK BY FULLY OPENING AND FULLY CLOSING THE SLIDING COVER NextBolt User Manual 38 For support contact us a 1 800 408 7101 ext 102 Actuator Systems http www advancedactuators com Section V Unlocking the Actuator Systems NextBolt from outside In case of emergency override keys can be used to disengage the deadbolt Please use the following steps to unlock the Actuator Systems NextBolt from outside with your enrolled fingerprint e Fully lift the sliding cover located on the outdoor unit NextBolt User Manual 39 For support contact us a 1 800 408 7101 ext 102 Actuator Systems NextBolt User Manual http www advancedactuators com A single short beep will be heard and the fingerprint sensor will power on After the fingerprint sensor powers on rest any enrolled fingerprint on the sensor window to verify If fingerprint verification is successful the deadbolt will disengage and a single short beep will be heard If verification of enrolled fingerprint was not successful then 4 short beeps will be heard If this happens the fingerprint scanner wil
14. engage or four The tail piece the tail piece up and insert alert beeps are was not set the tail vertically through the heard properly cross slot of the deadbolt while the turn knob is in vertical position NextBolt User Manual 24 For support contact us a 1 800 408 7101 ext 102 1 When the sliding cover is fully lifted and immediately put down to engage the deadbolt but the deadbolt does not fully engage or four alert beeps are heard 1 Improper positioning of the strike and strike lining box It may be deflecting the deadbolt http www advancedactuators com 1 Check the position of the strike and the strike lining box When the sliding 1 Batteries not 1 Remove amp reinsert the cover is lifted up inserted batteries following and during daily use correctly __ signs in the battery nothing happens house fingerprint scanner does not 2 Check the connections and blink 2 Wires not make sure wires are fully connected plugged in properly Six beeps are heard Low Voltage Change the batteries when any function is performed Operation Manual Operation Manual Helpful Hints Please be sure to physically leave your door open until you have successfully enrolled the first user ADMINISTRATOR into the Actuator Systems NextBolt and have successfully verified the new user s fingerprint to unlock the door NextBolt User Manual 25 For support contact us a
15. ers on rest your pointer finger on the sensor window during the first of three scans e Keep your pointer finger on the scanning window thru all three scans e After the scanning is completed you will hear one of the following o Single long beep indicating that the operation was successful OR o Four beeps indicating that your fingerprint was not successfully enrolled If you hear four beeps please start the enrollment process over from the beginning NextBolt User Manual For support contact us a 1 800 408 7101 ext 102 Actuator Systems http www advancedactuators com e Close the sliding cover USER 2 through USER 99 Section II Enrolling Fingerprint Users 2 thru 99 Sliding cover must be closed before any programming sequence can begin As noted in the Helpful Hints section the third thru ninety ninth fingerprint users enrolled Users 3 thru 99 are automatically programmed at the USER level USER level fingerprints can only be used to unlock the door not to program the lock Please use the following steps to enroll additional fingerprint users Users 3 thru 99 NextBolt User Manual 31 For support contact us a 1 800 408 7101 ext 102 Actuator Systems http www advancedactuators com e Remove the battery cover from the indoor unit e Press the ADD button located on the indoor unit e Single beep will be heard NextBolt User Manual 32 For support contact us a 1 800 408 7101 ext 1
16. hout the need to verify the administrator again After you hear the long beep simply enter in the next KEYPRESS SEQUENCE from the APPENDIX A for the next user e Close the sliding cover to end the enrollment procedure NextBolt User Manual 34 For support contact us a 1 800 408 7101 ext 102 Actuator Systems http www advancedactuators com Section Deleting Individual Fingerprint Users Sliding cover must be closed before any programming sequence can begin The Individual Fingerprint User Deletion programming function deletes the individual user you select from your enrolled users Please use the following steps to delete individual fingerprint users e With the battery cover removed press the DEL button located on the indoor unit e Short Double Beep will be heard NextBolt User Manual 35 For support contact us a 1 800 408 7101 ext 102 Actuator Systems http www advancedactuators com e Fully open the sliding cover located on the outdoor unit immediately e Sensor will flicker for less than one second e A single short beep will be heard and the fingerprint sensor will power on e Rest an Administrator s fingerprint on the scanning window e When the LED light goes out enter the keypress sequence The chart is in Appendix A of this manual o If you hear four beeps this indicates that the Administrator was not recognized If you hear five beeps this indicates the user delet
17. ion was not successful Begin again from the first step of Section II When one long beep is hear the user has been deleted successfully Once the deletion is successful you are not required to verify the administrator to remove additional users Simply enter the next user NextBolt User Manual 36 For support contact us a 1 800 408 7101 ext 102 Actuator Systems http www advancedactuators com id sequence and wait for the long beep for each user you wish to remove Close the sliding cover to end the deletion procedure e Close the sliding cover e Repeat steps from the beginning of Section III to delete the next most recently enrolled fingerprint user Section IV Deleting ALL Fingerprint Users Sliding cover must be closed before any programming sequence can begin Deleting ALL enrolled fingerprint users will reset the lock and all users including Administrators fingerprints will be deleted With no fingerprints enrolled in the Actuator Systems NextBolt the deadbolt will engage disengage when the sliding cover is fully opened and immediately closed NextBolt User Manual 31 For support contact us a 1 800 408 7101 ext 102 Actuator Systems http www advancedactuators com Please use the following steps to delete ALL fingerprint users 1 Press and hold the DEL button 2 While holding down the DEL button add the other two buttons ADD amp OPEN CLOSE Now all three buttons on the lock will be h
18. l still turn on two additional times enabling users to try more If all the two additional verification attempts still fail please start the unlocking process over again from the beginning of this section 40 For support contact us a 1 800 408 7101 ext 102 Actuator Systems http www advancedactuators com e Close the sliding cover Section VI Locking the Actuator Systems NextBolt from Outside In case of emergency override keys can be used to engage the deadbolt Please use the following steps to lock the Actuator Systems NextBolt from outside when leaving NextBolt User Manual 41 For support contact us a 1 800 408 7101 ext 102 Actuator Systems http www advancedactuators com e Make sure your door is closed Open and immediately close the sliding cover Deadbolt will engage and a single short beep will be heard Section VII Locking and Unlocking the Actuator Systems NextBolt from Inside In case of emergency manual turn knob can be used to disengage the deadbolt Please use the following steps to lock and unlock the Actuator Systems NextBolt from inside NextBolt User Manual 42 For support contact us a 1 800 408 7101 ext 102 Actuator Systems Q http www advancedactuators com Press the OPEN CLOSE button located between the ADD and DEL buttons e Deadbolt will engage disengage and single short beep will be heard Support Contact the Actuator Syste
19. ms NextBolt dealer that you purchased the lock from OR Contact us at support advancedactuators com for additional support NextBolt User Manual 43 For support contact us a 1 800 408 7101 ext 102 Actuator Systems http www advancedactuators com APPENDIX A FINGERPRINT ENROLLMENT CODES 1 Keypress Sequence plus Open Close 1 ADD 2 ADD DEL 3 ADD ADD 4 ADD DEL DEL 5 ADD DEL ADD 6 ADD ADD DEL 7 ADD ADD ADD 8 ADD DEL DEL DEL 9 ADD DEL DEL ADD 10 ADD DEL ADD DEL 11 ADD DEL ADD ADD 12 ADD ADD DEL DEL 13 ADD ADD DEL ADD 14 ADD ADD ADD DEL 15 ADD ADD ADD ADD 16 ADD DEL DEL DEL DEL 17 ADD DEL DEL DEL ADD 18 ADD DEL DEL ADD DEL 19 ADD DEL DEL ADD ADD 20 ADD DEL ADD DEL DEL 21 ADD DEL ADD DEL ADD 22 ADD DEL ADD ADD DEL 23 ADD DEL ADD ADD ADD 24 ADD ADD DEL DEL DEL 25 ADD ADD DEL DEL ADD NextBolt User Manual sa For support contact us a 1 800 408 7101 ext 102 Actuator Systems http www advancedactuators com 26 ADD ADD DEL ADD DEL 27 ADD ADD DEL ADD ADD 28 ADD ADD ADD DEL DEL 29 ADD ADD ADD DEL ADD 30 ADD ADD ADD ADD DEL 31 ADD ADD ADD ADD ADD 32 ADD DEL DEL DEL DEL DEL 33 ADD DEL DEL DEL DEL ADD 34 ADD DEL DEL DEL ADD DEL 35 ADD DEL DEL DEL ADD ADD 36 ADD DEL DEL ADD DEL DEL 37 ADD DEL DEL ADD DEL ADD 38 ADD DEL DEL
20. ncedactuators com support php or our knowledgebase at http Awww advancedactuators com kb For all Tech Support Questions Call 407 567 7130 Ext 102 or Email support advancedactuators com To reach the main office 407 567 7130 Frequently Asked Questions FAQ Here are a few answers to common installation questions These account for 90 of the inquiries we receive to our technical support department 1 When you mate the front and back of the lock together insure the bolt is in the locked out position and the knob is pointing directly down This will cause the notch the tailpiece fits into to be in a vertical position 2 Insure the wire that runs between the two lock pieces does not interfere with the rotation of the tailpiece 3 Issues with fingerprint recognition are due to a poor enrollment 95 of the time High quality enrollments are the key to fast and reliable operation of your new lock Ensure when you place your finger on the pad for enrollment that as much of your finger as possible is in contact with the sensor Do not move your finger while it is being scanned wait until you hear the long beep Keep even pressure applied to the center of the fingerprint pad You can enroll the same finger more than one time It also can help enrollment if the finger you use is not overly dry a We have included in your pack 2 disposable fingerprint enhancement pads These pads are only necessary in the event you had trouble enr
21. ngerprints to A Unlock the door B Authenticate Administrators enrolled fingerprints to program the Actuator Systems NextBolt http www advancedactuators com Before enrolling and verifying fingerprints make sure to read the following helpful hints for Fingerprint Enrollment and Verification Generally the center of the vortex swirl of the fingerprint pattern is the key data point ideally it is placed in the center of the small glass window in a consistent way Your finger should be flat motionless and held with light pressure in the same way each time See the picture below for some guiding drawings Light pressure when placing the finger on the scanner gives the best image but the finger must not move during scanning Moist fingers provide better images than dry ones If on cold dry days you have difficulty for example try moistening your finger with your breath or a little lotion Very dry dirty or scarred fingers are obviously not recommended since they will obscure the fingerprint The pointer finger is by far the best fingerprint to enroll The thumb is the second best digit If the pointer finger is difficult to enroll or verify try enrolling the same NON ADMIN fingerprint 2 or 3 times at slightly different angles EX Enroll same pointer finger as users 3 4 and 5 In the event you still have trouble enrolling fingerprints we have included 2 fingerprint pads in your box Moisten your fingers with one of these
22. olling To use just wipe your finger with one of the pads 5 seconds before enrollment These pads considerably enhance the quality of the ridges of the fingerprint Thanks again from your friends at Actuator Systems
23. olt User Manual 10 For support contact us a 1 800 408 7101 ext 102 Actuator Systems http www advancedactuators com 4 3 Sizing Tail Piece to the right length The Actuator Systems NextBolt is designed to fit door thicknesses of 1 3 8 to 2 Four pre sized tailpieces are included with the Actuator Systems NextBolt for 1 3 8 1 1 2 1 34 and 2 thick doors Your door thickness and length of the tailpiece being used must match exactly EX If your door is 1 34 thick then you must use the 1 34 long tailpiece The Actuator Systems NextBolt comes with the 1 34 tailpiece pre installed If your door is not 1 34 thick but the thickness matches one of the other pre cut tailpieces included with the lock then you must swap out the tailpiece NextBolt User Manual 11 For support contact us a 1 800 408 7101 ext 102 Actuator Systems IF YOUR DOOR THICKNESS DOES NOT EXACTLY MATCH ANY OF THE PRE CUT TAILPIECES LENGTHS THEN YOU MUST TRIM THE PRE INSTALLED TAIL PIECE TO MATCH YOUR EXACT DOOR THICKNESS http www advancedactuators com If you need to trim the tailpiece be sure to measure the exact thickness of your door mark the tailpiece with a marker where it needs to be cut and trim the tail piece accordingly per the exact thickness of your door with a hacksaw or metal cutters Notes The motor could be dislodged if the tailpiece is not cut properly and is too long due to excessive pre
24. or support contact us a 1 800 408 7101 ext 102 Actuator Systems 29 http www advancedactuators com 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 NextBolt User Manual 49 For support contact us a 1 800 408 7101 ext 102 Actuator Systems 60 http www advancedactuators com 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 71 78 79 80 81 82 83 84 85 86 87 88 89 90 NextBolt User Manual 50 For support contact us a 1 800 408 7101 ext 102 Actuator Systems 91 http www advancedactuators com 92 93 94 95 96 97 98 99 NextBolt User Manual 51 For support contact us a 1 800 408 7101 ext 102 Actuator Systems We would like to personally thank you for your purchase of our exciting NextBolt Series biometric deadbolt lock from Actuator Systems We hope you enjoy using it as much as we enjoy developing this technology for you http www advancedactuators com For more helpful information about your NextBolt please visit www adva
25. ration Manual cetacssmmteimsmsamnmdmims Section I Enrolling 29 Section III Deleting Individual Fingerprint Users 35 Section IV Deleting ALL Fingerprint Users 37 Section V Unlocking the Actuator Systems NextBolt eeteanuadeee 30 Section VI Locking the Actuator Systems NextBolt from cims 4 Section VII Locking and Unlocking the Actuator Systems Nextbolt from Inside 42 APPENDIX Aqua mesmentodsetsonitzentas i USER ENROLLMENT TABLE eener 47 Special THANKS from Actuator Systems NextBolt User Manual 2 For support contact us a 1 800 408 7101 ext 102 Actuator Systems http www advancedactuators com 1 Parts Please familiarize yourself with all the parts in the packaging box of the Actuator Systems NextBolt If any part is missing or damaged contact our service center or your local dealer Outdoor Unit Indoor Unit Strike Lining Box Indoor and Outdoor Rubber Gaskets Strike Plate Keys NextBolt User Manual 3 For support contact us a 1 800 408 7101 ext 102 Actuator Systems Deadbolt Latch 2 34 backset 70mm http www advancedactuators com Deadbolt Latch 2 3 8 backset 60mm EE Screws 90 mm 17 Screws Alkaline
26. ssure Warranty will be voided if this occurs NextBolt User Manual 12 For support contact us a 1 800 408 7101 ext 102 Actuator Systems http www advancedactuators com 4 4 Installation of the Outdoor Unit 1 Attach the rubber gasket to the back of the outdoor unit 2 Make sure the deadbolt is engaged NextBolt User Manual 13 For support contact us a 1 800 408 7101 ext 102 Actuator Systems http www advancedactuators com 3 Make sure the tail piece is vertical 4 Insert tail piece through the cross slot of the latch NextBolt User Manual 14 For support contact us a 1 800 408 7101 ext 102 Actuator Systems http www advancedactuators com 5 Insert the connector and wire through the cylinder hole below the deadbolt latch 6 On the INSIDE side of the door screw the fixing plate to the outside door lock using the two 90mm screws You can break off the screws to the needed length depending on your required thickness Insure these have a snug fit NextBolt User Manual 15 For support contact us a 1 800 408 7101 ext 102 Actuator Systems http www advancedactuators com 4 5 Installation of the Indoor Unit The outdoor unit should now be firmly fastened to the outside of the door This will make it much easier and simpler to attach the inside portion of the lock 1 Select the proper door opening orientation on the back plate
27. te installation template according to the length of the backset Fold and apply the template to the edge of the door bevel Mark the center point of the cylinder hole on the door face and then mark the center point of the deadbolt hole on door edge as indicated on the template For installation of combination set door handle and deadbolt it is recommended that the distance is 5 4 between the two center points Mark the center points of the two small holes on the door face for the two upper fixing posts mounted on the top plate of the outdoor unit as indicated on the installation template NextBolt User Manual For support contact us a 1 800 408 7101 ext 102 Actuator Systems 3 12 Bore holes http www advancedactuators com w s A Bore a2 1 8 diameter hole in the center of door face for chassis It is recommended to bore this hole from both sides of the door to avoid splintering B Bore a 1 diameter hole in the center No of door edge for deadbolt 2 1 8 3 2 Deadbolt Latch Selection There are two deadbolt latches in each box one with a 2 3 8 60mm backset and the other with a 2 34 70mm backset Make sure which length you will need and select the right one before installation NextBolt User Manual 8 For support contact us a 1 800 408 7101 ext 102 Actuator Systems 4 Installation http www advancedactuators com 4 1
Download Pdf Manuals
Related Search