Faultless G2X2LYED0AA-F Instructions / Assembly
Contents
1. 1 3 4 1 9 16 1 3 8 O54mm 2 1 8 Backset 70mm 2 3 4 Backset 60mm 2 3 8 1 Remove lever lock or do not install lever lock prior to painting your door 2 Do not let any water or liquid into the lockset during installation process TEMPLATE IMPORTANT BEFORE PROCEEDING NOTE MEASUREMENTS BELOW ARE JUST A GUIDELINE Please measure your door to determine the exact center of your door edge 6 54mm 2 1 8 25mm 1 60mm 2 3 8 or 70mm 2 3 4 A B DOOR PREPARATION 2 DOOR PREPARATION Use Diagram of spade bit here and not Drill bit NOTE If replacing an existing lock or installing in a pre drilled door begin with page 7 Fold the template against the door edge as shown in below illustration mark and drill a pilot hole for latch on door edge select backset 60mm or 70mm to mark and drill a pilot hole for selected backset on door face It is recommended to mark centerline of the hole on door about 36 inches 914mm above the floor 7 60mm 2 3 8 70mm 2 3 4 INSTALLATION INSTRUCTIONS 3 LATCH INSTALLATION A Pull the drive shaft backward for adjustment to 70mm 2 3 4 B Push the drive shaft forward for adjustment to 60mm 2 3 8 Drive shaft Drive shaft 8 INSTALLATION INSTRUCTIONS A Insert the latch into the latch hole Using the faceplate as a pattern TRACE a line along the out edge of the faceplate and chisel a 4mm 1 8 slot in the marked out area Face pl2. received including interference that may cause undesired operation Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help FEDERAL COMMUNICATIONS COMMISSION STATEMENT 38 This Class B digital apparatus complies with Canadian ICES 003 Cet appareil numerique de la classe B est conforme a la norme N
3. 0 13 to change inside and outside levers to proper direction you can skip the following instructions about exchange of lever to setup mode started in page 28 INSTALLATION INSTRUCTIONS 20 For lever removal and assembly process please see page 21 25 8 1 EXCHANGE OF LEVER 21 Catch tool INSTALLATION INSTRUCTIONS 8 2 EXCHANGE OF LEVER REMOVAL OF INSIDE LEVER Insert the catch tool into the access hole on the lever Once the lever is released remove the catch tool and pull the lever off 22 INSTALLATION INSTRUCTIONS A Insert the key horizontally and turn counter clockwise 90 degrees B Insert the catch tool into the access hole on the lever Once the lever is released remove the catch tool and pull the lever off NOTE This step is required if you are rekeying the lock A B 8 3 EXCHANGE OF LEVER REMOVAL OF OUTSIDE LEVER 23 INSTALLATION INSTRUCTIONS A B C D 8 4 SWAP INSIDE AND OUTSIDE LEVERS REMOVAL OF CYLINDER A With lever removed withdraw the key B Slide the cylinder retaining collar off the shank of the lever C Remove the cylinder D Insert cylinder into the other lever Align the tab of the cylinder retaining collar with the slot of lever shank and push it back to secure cylinder in place The slot of the lever Protrusion 24 INSTALLATION INSTRUCTIONS 8 5 SWAP INSIDE AND OUTSIDE LEVERS ASSEMBLE OUTSIDE LEVER A Turn the key counter clockwise by 90 degree to vertic
4. 1 Rotate the internal thumbturn to horizontal position press the red indicator is on you are in setup mode 2 Input programming code press press 20 press enter new user code press enter new user code press may input 100 sets of user code consecutively the red indicator is off in 10 seconds If a number of passwords are to be added at the same time enter new password and press prior to the indicator light timing out 10 seconds after the last press of a keypad button 3 DELETE INDIVIDUAL EXISTING USER CODE Procedures 1 Rotate the internal thumbturn to horizontal position press the red indicator is on you are in setup mode 2 Input programming code press press 30 press enter existing user code to be deleted repeat pressing and entering existing user code to be deleted consecutively until each set of user code is deleted the red indicator is off in 10 seconds if multiple sets of user codes are to be deleted at the same time enter each user code to be deleted and press repeatedly prior to the indicator light timing out 10 seconds after the last press of a keypad button 2 ADD A USER CODE MAXIMUM 100 SETS USER CODES WITH 4 8 DIGITS IN LENGTH 3 DELETE INDIVIDUAL EXISTING USER CODE SETUP MODE 30 4 DELETE ALL THE EXISTING USER CODES AT ONCE Procedures 1 Rotate the internal thumbturn to horizontal position press the red indicator is on you are in setup mode 2 Input programming c
5. 8 1 EXCHANGE OF LEVER 8 2 EXCHANGE OF LEVER REMOVAL OF INSIDE LEVER 8 3 EXCHANGE OF LEVER REMOVAL OF OUTSIDE LEVER 2 DOOR PREPARATION 6 2 TEMPLATE 5 6 1 TO RESET DIRECTION OF INSIDE LEVER 6 2 TO RESET DIRECTION OF OUTSIDE LEVER 8 4 SWAP INSIDE AND OUTSIDE LEVERS REMOVAL OF CYLINDER 8 5 SWAP INSIDE AND OUTSIDE LEVERS ASSEMBLE OUTSIDE LEVER 8 6 SWAP INSIDE AND OUTSIDE LEVERS ASSEMBLE INSIDE LEVER CONTENTS MAIN OPERATING INSTRUCTIONS SETUP MODE 1 CHANGE PROGRAMMING CODE 2 ADD A USER CODE 3 DELETE INDIVIDUAL EXISTING USER CODE 5 DISABLE ALL THE EXISTING USER CODES VACATION MODE 6 DISABLE BUTTON SOUND MUTE MODE 7 SETTING AUTO LOCK TIME DELAY 8 RESTORE FACTORY SETTING OPERATION MODE TROUBLESHOOTING GUIDELINE DATA RECORDS 4 DELETE ALL THE EXISTING USER CODES AT ONCE 3 DECLARATION AND SAFETY STATEMENTS 1 TO ACTIVATE AUTO LOCKING AUTOMATIC RE LOCKING 2 TO OPEN UNLOCK THE DOOR 3 TO DEACTIVATE AUTO LOCKING AUTOMATIC RE LOCKING 4 A B C D E F G H I J K L M INSTALLATION INSTRUCTIONS A Key B Exterior Assembly C Mounting Plate D Interior Assembly E Decorative Cover F Battery Pack Cover G Lever H 5 16 7 8mm Screw 2 I 1 1 4 32mm Screw 2 J Latch K 6 8 19 2mm Wood Screw 4 L Strike M Dust Box 1 COMPONENTS 5 Fold here Place on door edge 51 45 40 35 Drill 1 25mm hole at center of door edge 2
6. CTIVATE AUTO LOCKING AUTOMATIC RE LOCKING Use a flat tool to turn the slotted turn on the inside as shown from vertical position to horizontal position to deactivate auto locking mode The device is then served as a passage lever A Keypad does not respond B Can not change programming code C Can not delete all the existing user codes at once 1 Check to see if the batteries are properly installed 2 Check to see if the indicator is flashing It means the battery is low if the indicator keeps flashing 3 Make sure the cable is well connected to the port 4 Please contact us if such problem could not be solved 1 Complete the CHANGE PROGRAMMING CODE process by inputting codes within 10 seconds 2 Make sure you have entered the new programming code twice correctly or go back to the factory setting refer to page 31 again 3 Please contact us if such problem could not be solved 1 Make sure all codes are entered within 10 seconds 2 Make sure you have entered the correct programming code 3 Cancel button should be pressed and held for 3 seconds at least TROUBLESHOOTING GUIDELINE 35 Solutions Problem 1 Make sure all codes are entered within 10 seconds 2 Make sure you have entered the correct programming code 3 The new user code will not be accepted if 100 user codes are already stored in the memory D Cannot add a new user code E Can not open the door after input a correct user code F Yellow
7. ELECTRONIC KEYPAD LEVER LOCK User s Guide WARNING CAUTION 1 IMPORTANT SAFETY INSTRUCTION 1 To prevent damage to the finish DO NOT use any abrasives sharp objects or harsh chemical products containing alcohol petroleum solvents acids or acetone to clean this lockset 2 To prevent damage to the sensitive electronic components DO NOT allow any liquids to enter lockset while installing or cleaning 1 Do not attempt to disassemble any internal components of this lockset as this WILL void the limited warranty 2 Do not drop or hit strike the lockset as excessive shock may result in permanent damage STRONGLY recommended that you always create a written backup of the programming code and individual user codes Please use the last page of this booklet as your reference 5 For your Security please remember to change this lockset s factory default programming code to a PERSONAL programming code prior to normal day to day use of this product See Page 28 6 It is STRONGLY recommended that you use only ALKALINE BATTERIES to operate this product 3 Do not use sharp objects to press key buttons 4 It is CONTENTS INSTALLATION INSTRUCTIONS 1 COMPONENTS 3 LATCH INSTALLATION 4 STRIKE PLATE INSTALLATION 5 LEVER DIRECTION DETERMINATION 7 1 MOUNTING EXTERIOR ASSEMBLY 7 2 PREPARING TO MOUNT INTERIOR ASSEMBLY 7 3 REMOVING DECORATIVE COVER 7 4 MOUNTING INTERIOR ASSEMBLY 7 5 BATTERY INSTALLATION 7 6 REINSTALL LEVER
8. MB 003 du Canada This device complies with Industry Canada licence exempt RSS 210 standard Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation of the device 39 IC REGULATIONS Rev 12 05 00 G36 L000012
9. al position as shown B Push outside lever back to slide onto spindle until it is securely engaged 25 INSTALLATION INSTRUCTIONS 8 6 SWAP INSIDE AND OUTSIDE LEVERS ASSEMBLE INSIDE LEVER Align inside lever and push it back to slide onto spindle until it is securely engaged 21 7 Low Battery Indicator 26 1 Indicator 2 Keypad 3 Cancel Button 5 Key Override 4 Confirm Button 6 Thumbturn Auto Locked Unlocked switch MAIN OPERATING INSTRUCTIONS 27 MAIN OPERATING INSTRUCTIONS 28 SETUP MODE 1 CHANGE PROGRAMMING CODE 1 The pre set programming code of the product is 123456 please change it before operating the lockset 2 Keep a written copy of programming code in a safe place 3 Programming code can be used to unlock Procedures 1 Rotate the internal thumbturn to horizontal position press the red indicator is on you are in setup mode 2 Enter 1 2 3 4 5 6 or current Programming Code press press10 press input new programming code press the red indicator is off in 10 sceonds IMPORTANT The internal thumbturn enables disables exterior lever The internal thumbturn is horizontal position to be unlocked passage lock The internal thumbturn is vertical position to be auto locked entry lock THIS PROGRAMMING CODE MUST BE 6 DIGITS IN LENGTH 1 CHANGE PROGRAMMING CODE 29 2 ADD A USER CODE MAXIMUM 100 SETS USER CODES WITH 4 8 DIGITS IN LENGTH Procedures
10. ate should fit flush with door edge B Insert the latch into the latch hole and fasten with screws Show pencil marking outer edge of latch faceplate with Dotted lined directional arrows as you do not just carve out the screw holes A B 3 LATCH INSTALLATION 9 INSTALLATION INSTRUCTIONS 4 STRIKE PLATE INSTALLATION A Placing the strike plate on the door frame TRACE a line along the out edge of the strike plate and chisel a 3mm 1 8 slot in the marked out area B Chisel out a hole measuring 32 x 24 x 13mm 1 1 4 X1 X1 2 in association with the size of the dust box C Fasten the strike and dust box with screws Door frame Strike Dust box INSTALLATION INSTRUCTIONS 5 LEVER DIRECTION DETERMINATION NOTE Do not install the lock when the lever is at vertical position Before lock installation please determine the inside lever direction according to the opening direction of door as shown 10 11 INSTALLATION INSTRUCTIONS NOTE Do not install the lock when the lever is at vertical position Before lock installation please determine the outside lever direction according to the opening direction of door as shown 5 LEVER DIRECTION DETERMINATION 12 Button INSTALLATION INSTRUCTIONS 6 1 TO RESET DIRECTION OF INSIDE LEVER Press the button below SWITCH mark of the interior assembly to free inside lever and turn it upward then down to the correct horizontal direction with the door Lever will
11. be fixed in position after a sound of click Follow the page 10 to determine the direction of the lever 13 INSTALLATION INSTRUCTIONS 6 2 TO RESET DIRECTION OF OUTSIDE LEVER Use a screwdriver to press the button in the hole below SWITCH mark of the exterior assembly to free outside lever and turn it upward and then down to the correct horizontal direction with the door Lever will be fixed in position after a sound of click Follow the page 11 to determine the direction of the lever Cable INSTALLATION INSTRUCTIONS 14 7 1 MOUNTING EXTERIOR ASSEMBLY A Slide the spindle and screw posts through the latch and thread the cable under the latch B Thread the cable through the rectangular hole in the mounting plate and combine the posts of the mounting plate and the exterior assembly C Fasten the mounting plate with 2 screws 32mm or 1 1 4 while ensuring the exterior assembly is held in the true vertical position on door face NOTE Exterior assembly will not sit completely flush with door face until screws are tightened completely as there are 2 anchoring spikes which prevent the exterior assembly from shifting wobbling during usage Mounting plate A B C 15 INSTALLATION INSTRUCTIONS A Remove battery pack cover by pushing it up to the top position B Remove the lever by inserting the catch tool into the access hole and depressing to release catch while gently pulling on lever Once catch has been re
12. indicator is on or keeps flashing 1 Make sure you have entered the correct user code 2 Check to see if the indicator is flashing If the indicator is flashing please replace the batteries with new ones 3 Please make sure the strike plate is installed correctly if you see the latch is jammed 1 It means these batteries are getting low please replace all the batteries 2 Use alkaline batteries only TROUBLESHOOTING GUIDELINE Solutions Problem G What happens if the lever lock cannot be auto locked after closing door 1 Make sure the arrow of the thumbturn is directed to LOCK 2 Make sure the key is withdrawn from the lock H Yellow indicator keeps flashing or the lock keeps beeping after unlocking 1 It means these batteries are getting low please replace all the batteries 2 Use alkaline batteries only 36 37 PROGRAMMING CODE NAME CODE SECURITY INSTRUCTIONS 1 Do not share your programming code with anyone else 2 Keep a written copy of all valid user codes in safe place You may use the table below to record your information 3 Code capacity 100 sets maximum 4 You are advised to re program all codes if you lost any security information of the lever lock DATA RECORDS NAME CODE NAME CODE This device complies with Part 15 of the FCC Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference
13. leased remove the catch tool from the access hole to allow the lever to pull off completely C Follow the steps on page 16 to remove the decorative cover Please follow two steps Please follow two steps 7 2 PREPARING TO MOUNT INTERIOR ASSEMBLY Battery pack cover Catch tool Decorative cover 1 One step 2 Two step 1 One step 2 Two step A B C 16 INSTALLATION INSTRUCTIONS 7 3 REMOVING DECORATIVE COVER A Remove decorative cover by holding fingers at cover s edges as shown in photo A B Use thumbs to press THUMBTURN as shown in photo B and photo C A B C Interior assembly Blue wire 17 INSTALLATION INSTRUCTIONS A Insert the cable into the connector port firmly with blue wire just under the red black wires of the port as shown B Slide the interior assembly onto square spindle of the exterior assembly C Fasten the interior assembly on the mounting plate with 2 screws 7 8mm or 0 3 7 4 MOUNTING INTERIOR ASSEMBLY A B 18 INSTALLATION INSTRUCTIONS 7 5 BATTERY INSTALLATION A Snap the decorative cover back onto the interior assembly B Place four alkaline batteries into the battery pack Following the imprinted guide C Replace the battery pack cover as shown A B C 19 INSTALLATION INSTRUCTIONS 7 6 REINSTALL LEVER Reinstall the lever after the decorative cover is snapped back onto the interior assembly NOTE If you follow page 1
14. ode press press 40 press press and hold C for 3 seconds until a beep is heard 5 DISABLE ALL THE EXISTING USER CODES VACATION MODE Procedures 1 Rotate the internal thumbturn to horizontal position press the red indicator is on you are in setup mode 2 Input programming code press press 50 press Please repeat the above procedures to enable all the user codes This will delete all the user codes EXCEPT the programming code NOTE If you will be away from home for vacation please use vacation mode to prevent anyone accessing your lock and this will just make the codes Temporarily INACTIVE not DELETE them from the unit 4 DELETE ALL THE EXISTING USER CODES AT ONCE 5 DISABLE ALL THE EXISTING USER CODES VACATION MODE SETUP MODE 31 6 DISABLE BUTTON SOUND MUTE MODE Procedures 1 Rotate the internal thumbturn to horizontal position press the red indicator is on you are in setup mode 2 Input programming code press press 60 press Please repeat the above procedures to enable the button sound 7 SETTING AUTO LOCK TIME DELAY Procedures 1 Rotate the internal thumbturn to horizontal position press the red indicator is on you are in setup mode 2 Input programming code press press 70 press press the seconds for 5 90 press the red indicator is off in 10 seconds 8 RESTORED FACTORY SETTING Procedures Rotate internal thumbturn to horizontal position remove any of the batte
15. ries press and hold until all batteries are installed again reset is finished when a long beep of 3 seconds and a short beep Such action will delete all the stored will be reset to the default DEFAULT VALUE IS 5 SECONDS delay time of auto locking the lock beeps user codes the programming code code 123456 Please re change the programming code for the safety purpose NOTE Do not enter leading zeros use 5 not 05 6 DISABLE BUTTON SOUND MUTE MODE 7 SETTING AUTO LOCK TIME DELAY 8 RESTORED FACTORY SETTING SETUP MODE 10 3 TO LOCK OPERATION MODE Vertical arrow position is auto locked Horizontal arrow position is unlocked A B 32 1 TO ACTIVATE AUTO LOCKING AUTOMATIC RE LOCKING NOTE Must turn the thumbturn to vertical auto locked position while completing setup mode A Use a flat tool to turn the thumbturn on the inside to vertical position as shown to activate auto locking mode i e this device will be relocked automatically in 5 seconds default value after unlocking Then outside lever is free turning without retracting latch to open the door B Turn the thumbturn on the inside to horizontal position as shown to deactivate auto locking mode 33 OPERATION MODE 2 TO OPEN UNLOCK THE DOOR A Enter the correct user code or programming code B Upon the green indicator light on and a short beep heard turn the outside lever to unlock OPERATION MODE 34 3 TO DEA
Download Pdf Manuals
Related Search