Design House 702530 Use and Care Manual
Contents
1. Gl DESIGNHOUSE Keypad Lock Installation Instructions WWW TODAYSDESIGNHOUSE COM Customer Service 1 800 558 8700 el DESIGNHOUSE KEYPAD LOCK STOP Please read instructions before removing Design House Keypad lock from packaging 1 Unscrew and remove Cover Loop and Plastic Gasket from Interior Panel with provided tool Wrench 2 Remove Interior Cover Plate screws 4 to expose Battery Box 3 Unscrew and remove two mounting screws 4 Interior and Exterior can be removed from the styrofoam packaging 5 Proceed with installation of Keypad Lock Page 2 ral DESIGNHOUSE Cover loop Interior cover plate Interior cover plate Interior panel Spindle Keypad Lever Entry ace Panel Keypad Deadbolt Entry Exterior Panel Interior Interior Panel Cover Plate screws 4x2 4x50MM 4x1 38 b screws 4x3 D screws Cylinder Cover Cover Remover Manual Override Door Preparation Drilling Template Wrench For Lever Entry Lock Page 3 KEYPAD LOCK P Installation Instructions 0 1 Use template provided to prepare door 9 10 11 12 13cm Single Latch Hole Dimension Template 25mm Depth D 4 118 3mm Y T oettegs San ae gt e ta aats an LJ s ae Ba 1 s saan Front Handle Center Line s amp a a peseeece E amp a a a gt nnnnfpnun2. factory set Master Code Change to new Master Code Program all new User Numbers and User Passwords as listed above Page 8
3. owner manager should keep this information confidential User Number 3 digits Identifies the user Property owner manager should keep a log of User Numbers User Password 6 digits User enters this code on the keypad to gain entry into building Programming Changing Codes Changing the Master Code initial use Press Factory Set Master Password New Master Password New Master Password Page 7 KEYPAD LOCK P Adding a User Password Press Master Password 3 digit User Number 6 digit User Password 6 digit User Password Example To add User Number 005 with User Password 123456 press Master Password 005 123456 123456 Deleting a User Password Press Master Password 3 digit User Number 3 digit User Number Changing a User Password Press User Password to be changed New User Password New User Password Enabling Passage Function Press any keyto open the door Press Master Password Disabling Passage Function keeps door inLOCKED state openedwith valid User Passwords Press Master Password USERS To Open the Lock Press User Password After green light goes ON press lever or rotate knob to open door within 5 seconds In case of loss of user records or other need to RESET all passwords Dismantle the Keypad Lock assembly Press the RESET button on the inside of the Exterior Panel Lock will return to
4. Latch Hole d 2 1 8 54mm 1 26mm Fig Page 4 cain el DESIGNHOUSE 2 Drill andprepare the doorframe for the PlasticInsert and Strike Plate making sure the holes arelevel and adirect match forthe door lock drilling See Fig A 1 3 4 44mm 2 1 4 1 1 8 57mm 28mm 1 2 f 13mm Fig A 3 Insert latchto prepared doorand attached with two 3 5x3 4 3 5x20MM screws See Fig 1 Door e Door e Deadbolt 3 5x20mm screw 3 5x20mm screw Fig 1 4 Install 4 AA alkaline batteries in the Battery Box on the Interior Panel 5 Feed the power wire from the Exterior Panel with keypad through the door hole A and latch see Fig 2 Connect the power wire to the battery box 6 Attach the Exterior Panel making sure the lock Spindle is squarely inserted into mount ing plate on Interior Panel through door hole A Be sure to secure the metal panels to the inner edges of the rubber gaskets for a sealed installation on both the interior and exterior sides 7 Attach the Exterior Panel and the Interior Panel with two 4x1 3 8 4x35MM or 4x1 97 4x50MM screws depending on different door thicknesses 8 Attach the Interior Cover Plate over the Battery Box and Interior Panel Page 5 KEYPAD LOCK P 9 Feed Cover Loop and plastic gasket ring over the interior handle Screw Cover Ring tightly to secure the interior assembly Lever Entry Only Attach the In
5. terior Cover onto the Interior Panel and fix them with two 3x10mm screws on both sides of Interior Cover See Fig 2 Deadbolt Entry Only Cover loop Interior cover plate Interior cover plate Interior panel power wire Keypad Lever Entry oo Panel Keypad Deadbolt Entry 10 Place Plastic Insert into prepared hole on door frame Attach Strike Plate with two self tapping screws 11 Verify that the Door Latch engages with the Strike Plate on the doorframe Door frame Fig 3 Page 6 Spindle Exterior Panel ran el DESIGNHOUSE There are two ways to open Design House Keypad Locks Enter a valid 6 digit password the green indicator light will go ON use the lever or knob to open the latch within 5 seconds Manual override keys for emergency use IMPORTANT 1 The factory set Master Code is 111111 Please change the Master Password to a new 6 digit Master Code on the initial use 2 The Design House Keypad Entry Lock holds 300 User Passwords 3 The Design House Keypad Entry Lock makes several sounds Three short beeps indicate an incorrectly keyed code Door will not unlock One long beep indicates a correctly keyed code Open the latch within 5 seconds to open the door Code Definitions Master Code 6 digits Required for making changes and additions to all codes Factory set Master must be changed the Ist time the lock is used for increased security Property
Download Pdf Manuals
Related Search