Allure Walk In Tubs S60WL Instructions / Assembly
Contents
1. check with local codes for requirements Any junction box es installed should be moisture proof and unreachable while sitting or standing in the tub or while touching the faucet s All electrical connections must be carried out by a certified electrician in accordance with local electrical requirements and codes TYPICAL ELECTRICAL CONNECTION A typical electrical connection is shown below A dedicated circuit is hardwired to a GFCI breaker Your installation must conform to local codes 1 Tub wiring 2 Dedicated circuit 3 Breaker box or subpanel with 25 amp GFCI breaker Note Tub must be grounded and bonded according to local electrical codes 14 ACCESS PANELS Your tub is designed for a trouble free service In the unlikely event that service is necessary there are two access panels in the front of the tub These are held in place by magnets and can be removed with the suction cup tool included with your tub ACCESS PANELS IN PLACE ACCESS PANELS REMOVED EXTENSION PANELS In the event that you wish to install your tub in a space wider than the tub itself there is an extension panel kit inluded with your tub Check the diagram and photos below for installa tion tU The panels are held in place by metal clips as shown below NOTE The Extension Panels are for aesthetic purposes only and are not designed to support weight NEVER PLACE ANY ELECTRICAL DEVICES RADIO TV ETC ON THE EXTENSION PANE2. it may not re enter stock for 2 5 8 weeks If a backorder part s is needed immediately the customer can request air shipment from our manufacturing facilities and will be responsible for variable international shipping rates Air Shipped parts can require 1 3 weeks for production ATTENTION Please contact ALLURE WALK IN TUBS if any items are missing misplaced or defective or if you have any questions or concerns with your product We will be glad to assist you promptly You may contact one of our friendly and helpful representatives at 1 877 629 5503 Monday through Friday from 8 00 AM to 5 00 PM Pacific Standard Time We will respond rapidly to provide a solution Thank you for your business and please enjoy your new Allure Walk In Bathtub 20 NN 1917 Walk In Tubs Technical Support Call toll free 877 629 5503
3. water tempera ture of 104 If water jets are on and temperature is not maintained remove access panel and check to be sure red light is illuminated on inline heater when water jets are in operation During cold winter months my tub will not fill up with enough hot water Home water heater capacity too small Install a larger capacity hot water heater a fast recovery hot water heater or an on demand hot water heater How should I clean the tub See page 18 of manual What is the round chrome object in the bottom of the doorway This 1s a door drain a safety feature which allows excess water to drain away from the doorway in the event of a door seal leak and to drain away standing water in the door sill after bathing Should I leave the bathtub door open or closed when I am not using 1t Always leave the door open when not in use This prevents the door seal from becoming com pressed over time leading to premature failure It can also prevent small pets from falling into the tub and becoming trapped 19 ALLURE WARRANTY POLICY Allure Bathroom Fixtures carry 5 year warranties This is a manufacturer s warranty which covers the mechanical and electrical assemblies of each bathroom fixture There is a lifetime warranty on the door seal Installation and associated labor is the singular responsibility of the owner not Allure Any costs related to installation and labor remain the responsibility of the owner and not Allu
4. L OPERATION Jetted Bathtubs Only CONTROL PANEL Once your Walk In Bathtub is assembled and in stalled the operation is simple On the inside wall of the tub you will see a control panel like the one shown at right and below There are three buttons which control the functions of the tub On Off Switch Water Air Jet Jet Switch Switch First turn on the power to the tub by pressing the On Off button The indicator light on the button will illuminate signifying that the tub has been turned on To activate the air jets press the Air Jet switch To activate the water massage jets press the Water Jet switch Note This will automatically activate the Inline Heater function to help maintain the water temperature at a comfortable level To turn off any or all functions including the power simply press the switch again All three buttons have indicator lights to show that they are in operation 16 INLINE HEATER FUNCTION The Inline Heater is pre programmed to maintain a water temperature of 104 F It is not designed to raise the temperature of cold bathwater but to maintain the water temperature while running the water jet system It is activated automatically when the water jet system is turned on senses the current water temperature and turns on and off automatically as needed to maintain this temperature Please note that the Inline Heater will not operate unless the water jet system is turned on as the water m
5. NN 194 Walk In Tubs Installation and Operation ELECTRICAL Complies with C oes ee Guidelines CONTENTS Introduction and Contact Information annn 3 Safety Instructions and Warnings cccccssseesecseseeeee 4 5 INSTALLATION AND ASSEMBLY Rough In DIMENSIONS ccccsescesseceessseceesceesseesesseeeneeeen 6 Location ANd Leveling cccceccsessecsescseesssssssesssessseesseees Assembling the Fittings cece ccessecsesssscessesseeeseeeeeeseeen 8 13 Hose Connections ou cece cceseccesescssesceseseuesseuessuesenessenens 11 12 Drain Connection wo cece ccc esc escesesesesesseserseseneveenenennn 11 Electrical Connection Jetted Bathtubs Only wo 14 ACCESS Panels ccccccccscsccessescsssescssvesesseesesueeseueeseneeseenay 15 Extension Panels ccccccccssecccssescssseessessveseesseesestneessenes 15 Control Panel cccccccccccccccccccccccuccccecccececuueuuueescseueeuuuaeseseeess 16 17 Inline Heater Water Jets CLEANING AND CARE Cleaning and Care e ssesssnessenessersnsrsrersrerrsrirrsrrnrerrnrerrnrnnns 18 FREQUENTLY ASKED QUESTIONS WARRANTY AND RETURN INFORMATION Warranty Information and Contact Policy ccceseeeeee 20 INTRODUCTION AND CONTACT INFORMATION Congratulations on your Walk In Bathtub purchase We know you ll enjoy many years of comfort and convenience using it Great care has gone into the design of our walk in tubs to simplify the install
6. RIQUE CANADIEN PARTIE 1 5 ROUGH IN DIMENSIONS Rough Floor ft imension inches S moder a Bb comin cum o e F ae ar azs s os ns 155 gt s z s azs 4075 os 105 1525 gt s sas 205 azs swozs o 13 v gt sors s azs aors o s v When installing tub use galvanized screw or nail driven into wall stud to overlap tub flange as shown below at left Do NOT insert screw or nail through tub flange as shown below at right This will weaken the tub s structure and void the warranty OK tub Tile tub Bathtub 2 3 Nail screw Nail screw does NOT 1 Wall stud passes pass through D Sheetrock Aii through tub tub flange flange damages 3 Nail or screw damages 4 9 Note Since no two customers installations will be identical these instructions are intended solely as a general reference Your installation may vary depending on your circumstances In stallations should be done by a licensed contractor or plumber and electrician LOCATION AND LEVELING First test fit the tub by placing it in the position where it will be installed Be sure the tub s drain lines up with the floor drain and note the position and length of the water inlet hoses ensuring that they will reach the connecting points of your home s water supply Once the tub is in place it must be leveled Do this by placing a carpenter s lev
7. RITE READ AND FOLLOW ALL INSTRUCTIONS LIRE ET SUIVRE TOUTES LES INSTRUCTIONS SAVE THESE INSTRUCTIONS CONSERVER CES INSTRUCTIONS WARNING RISK OF ACCIDENTAL INJURY OR DROWNING CHILDREN SHOULD NOT USE HYDROMASSAGE BATHTUB WITHOUT ADULT SUPERVISION AVERTISSEMENT RISQUE DE BLESSURE ET DE NOYADE NE PAS LAISSER UN ENFANT UTILISER LA CUVE A REMOUS EN L ABSENCE D UN ADULTE WARNING TO AVOID INJURY EXERCISE CARE WHEN ENTERING OR EXITING THE HYDROMASSAGE BATHTUB AVERTISSEMENT POUR EVITER LES BLESSURES USER DE PRUDENCE EN ENTRANT DANS LA CUVE A REMOUS ET EN LA QUITTANT WARNING RISK OF ELECTRIC SHOCK DO NOT PERMIT ELECTRIC APPLIANCES SUCH AS A HAIR DRYER LAMP TELEPHONE RADIO OR TELEVISION WITHIN 1 5M OF THIS HYDROMASSAGE BATHTUB AVERTISSEMENT RISQUE DE CHOC ELECTRIQUE NE PAS PLACER D APPAREILS ELECTRIQUES LUMINAIRE TELEPHONE RADIO TELEVISEUR ETC A MOINS DE 1 5M DE CETTE CUVE A REMOUS CAUTION TEST THE GROUND FAULT CIRCUIT INTERRUPTER PROTECTING THIS APPLIANCE PERIODICALLY IN ACCORDANCE WITH THE MANUFACTURER S INSTRUCTIONS ATTENTION VERIFIER REGULIEREMENT LE FONCTIONNEMENT DU DISJONCTEUR DE FUITE A LA TERRE CONFORMEMENT AUX INSTRUCTIONS DU FABRICANT USERS RESIDING IN CANADA MUST INSTALL THIS UNIT IN ACCORDANCE WITH THE CANADIAN ELECTRICAL CODE PART 1 LES UTILISATEURS RESIDANT AU CANADA DOIT INSTALLER CET APPAREIL SELON LE CODE ELECT
8. ation process and to make the operation of your tub easy and trouble free This manual will explain basic installation techniques and cover the opera tion of your tub Please read it completely before you or your installer begins the installation process Each and every tub is thoroughly tested at the factory before shipping We re confident that your Walk In Bathtub sets the standard for comfort quality and durability Should you have any questions please contact us at Allure Walk In Tubs 2340 W Broadway Rd Suite 103 Mesa Arizona 85202 Technical Support Call toll free 877 629 5503 Be sure to keep your packing slip delivery paperwork order information and any other documentation so that it may be referenced if necessary INSTALLATION INSTRUCTIONS UNPACKING AND MOVING YOUR TUB Inspect the shipping carton prior to unpacking Use caution with box cutters or razor knives In the unlikely event of damage which causes you to believe the bathtub inside may be damaged document the damage by taking a photograph of the damaged area and immediately contact your salesman or the company from which you purchased the tub When moving the tub prior to installation carry the bathtub by its metal sub frame Do NOT lift or carry the bathtub by the plumbing air hoses or deck Carry or move the tub by holding the stainless metal framework WARNING When using electrical products basic precautions should always be followed in
9. bove jets Turn on water jet system and run for 10 minutes Drain tub Run air jet system for 1 2 minutes to clear out lines Use a mild liquid household detergent such as or a spray on aerosol cleaner designed for use on fiberglass or acrylic tubs and wipe with a clean soft cloth A soft bristled brush may be used in the textured areas of the slip resistant floor if necessary CONN NN BW WN SUCTION COVER Jetted Bathtubs Only NEVER OPERATE THE WATER JET SYSTEM WITH THE SUCTION COVER OFF Remove any hair lint or soap residue from the suction cover An old toothbrush is especially good at cleaning soap scum from the holes in the suction cover On a monthly basis unscrew the suction cover and clean away any hair lint or debris from the cover and housing then remount the cover in place SURFACE CLEANING NEVER USE ABRASIVES OR POWDERED CLEANSERS They will scratch and dull the surface Always use a mild liquid household detergent such as or a spray on aerosol cleaner designed for use on fiberglass or acrylic tubs Test on a small area for the cleaner s effect on the finish DO NOT USE METAL SCRAPERS WIRE BRUSHES OR OTHER HARSH ABRASIVE TOOLS Never use bleach when cleaning the surface or the jet systems Light scratches and dulled areas may be restored to original luster by polishing with an automotive type rubbing compound designed for use with fiberglass and gelcoat Stubborn debris or construction adhesive res
10. cluding the following DANGER RISK OF ELECTRIC SHOCK Connect only to a circuit protected by a Ground Fault Circuit Interrupter Grounding is required The unit should be installed by a qualified service representative and grounded Use of this unit is for its intended purpose only Any attachments not included by the manufacturer are prohibited Children the elderly and the infirm should not use this unit without close and continuous supervision People using medications pharmaceutical or natural supplements sleep aids or those with adverse medical history should consult with a physician before using this product Water temperatures over 100 degrees Fahrenheit may pose a hazard to your health Use of your walk in bathtub immediately after eating or while under the influence of alcohol or medication is not recommended Alcohol or medication can cause drowsiness loss of consciousness and possible drowning Pregnant women should consult with a physician before using this bathtub In any bathtub there is always the risk of electric shock by external appliances Do not allow any electric aplliances hair dryers fans TV radio etc within 6 feet of this bathtub Do not operate without suction guard covers in place Installation must be done using a GFCI Ground Fault Circuit Interrupter Electrical and plumbing connections shall meet all local codes IMPORTANT SAFETY INSTRUCTIONS INSTRUCTIONS IMPORTANTES RELATIVES A LA SECU
11. el on the sides and edge of the tub and adjusting the feet Adjust the feet by loosening the locknuts and rotating the foot clockwise or counter clockwise as needed then tightening the locknuts Al though we check each tub at the factory movement during shipping may cause adjustments to be needed Failure to properly level the tub may cause incomplete drainage poor door seal alignment and other problems 1 Place level on edge of tub ew 2 Loosen locknuts on feet 3 Rotate foot up or down as needed to bring tub into level position 4 When tub is level tighten locknuts 5 Repeat as necessary until all four edges of tub show level Water supply hoses not included ASSEMBLING THE FITTINGS Your tub comes with high quality brass fittings coated with a durable chrome finish These include a Hand Shower a Spigot two Faucet Valves and a Diverter Valve These fittings and their attachment hardware can be found in the accessories box shipped inside the tub All threads should be wrapped with Teflon tape prior to assembly Faucet Handle Spigot and Faucet Handle Hand Shower and Valve Diverter Valve and Valve FAUCET ASSEMBLY Assembly of the faucet and fittings see diagram on next page is simple and straightforward The illustration below shows a completed installation FAUCET ASSEMBLY cont To assemble the faucet valves first install one rubber washer steel washer and retaining nut on faucet valve b
12. idue may be removed with denatured alcohol FADING Avoid locating your bathtub where it will receive continuous direct sunlight Continued exposure to the sun s UV rays can cause yellowing fading or discoloration 18 FREQUENTLY ASKED QUESTIONS Q A Does the bathtub come with supply hoses These are not supplied with the tub Hoses are available at any home supply or hardware store What size threads are the faucet taps The faucet threads are all 1 2 NIP What if I am missing a part Carefully double check all packaging and cartons If you are still missing a part please call 877 629 5503 and ask for the Parts Department There seems to be no power to the tub Check to be sure the top light ON OFF on the keypad is ON indicator light should be illuminated Check GFCI and or Circuit Breaker During initial Installation testing if tub will not operate be sure that the ground is dedicated and does not have any stray voltage present this will cause the control box not to energize The water jets or air jets do not come on Be sure there is power to the tub See question 4 above If air jets operate but water jets do not be sure the water jet sensors are below the water level see page 17 of manual The bathwater does not stay warm The heater operates automatically when the water pump feature is turned on If the water pump is not on then the heater will not function The heating system is designed to maintain
13. o the drain form ing a watertight seal Tub Floor Tub Drain Compression Ring Threaded Coupling Existing Stub From Floor ae oY 12 ASSEMBLING THE FITTINGS 46 INCH MODELS ONLY The 46 bathtub uses a slightly different faucet configuration Rather than a diverter within the spigot the diverter is a separate valve see below Installation and assembly is the same as pages 8 10 These fittings and their attachment hardware can be found in the accessories box shipped inside the tub All threads should be wrapped with Teflon tape prior to assembly Faucet Diverter Faucet Spigot Hand Handle Valve Handle Shower and Valve and Valve HOSE CONNECTION 46 INCH MODELS ONLY Connect hoses as shown in the diagram below Hot Water Faucet Diverter Cold Water Faucet Spigot Hand Shower Hot Water Supply Hose NOUO A 6 WN gt Hot Faucet to Diverter Hose 8 Diverter to Hand Shower Hose 9 Cold Faucet to Diverter 10 Diverter to Spigot Hose 11 Cold Water Supply Hose Water supply hoses not included 13 ELECTRICAL CONNECTION Your Walk In Bathtub functions on standard 110V 120V alternating current The electrical connection of your tub must be installed in accordance with the National Electrical Code and with all local codes Itis highly recommended that your tub be wired on a separate circuit with a dedicated GFCI circuit breaker rated for 25 amps If the new circuit run exceeds 100 feet
14. ody in order shown parts 5 6 and 7 Push faucet valve body 3 from bottom through correct hole in tub deck 4 and install second rubber washer steel washer and retaining nut 5 6 7 Do not overtighten Screw on chrome retaining ring 2 being careful not to damage the tub s finish Attach faucet handle 1 Note It may be necessary to remove small plastic cap 8 in the side of the handle to access the screw which holds the faucet on There is a hexagonal wrench provided in the faucet kit for this purpose Repeat procedure with second faucet valve Faucet handle Chrome retaining ring Faucet valve body Tub deck Retaining nut Steel washer Rubber washer Cap and Attachment Screw ONoaGAAROM SPIGOT ASSEMBLY Assembly of the spigot is as follows Insert spigot body 1 and trim ring 2 from above through hole in tub deck 4 Be sure locating pin 8 is aligned correctly with small hole in tub deck Install rubber washer 5 steel washer 6 and retaining nut 7 on spigot valve body 3 Thread the spigot valve body through trim ring and tighten into spigot body Tighten retaining nut Do not overtighten All threads should be wrapped with Teflon tape prior to assembly Spigot body Trim ring Spigot valve body Tub deck Rubber washer Steel washer Retaining nut Locating pin ONOAAWN Operation of the Diverter Valve to change water flow from Spigot to Hand Shower is done by raising or lowering the Diverte
15. r Stem on the rear of the Spigot as shown at left 10 HAND SHOWER ASSEMBLY To assemble the hand shower insert chrome hand shower support 1 through tub deck 3 from above Install rubber washer 4 and retaining nut 5 on threaded portion of chrome hand shower support Insert flexible hand shower hose not shown for clarity through chrome hand shower support 1 Connect the hand shower hose to the hand shower 1 Place hand shower 2 into chrome hand shower support The hand shower is designed to rest in an angled upright position when properly placed in the chrome hand shower support Thread hand shower hose as shown Chrome hand shower support Hand shower Tub deck Rubber washer Retaining nut aofhWM 11 HOSE CONNECTION Connect hoses as shown in the diagram below Cold Water Faucet ms 1 a K 2 Spigot Diverter 3 p Z Water supply hoses not included DRAIN CONNECTION To Overflow Hot Water Faucet Hand Shower Cold Water Supply Faucet to Spigot Line Cold Hand Shower Hose Faucet to Spigot Line Hot Hot Water Supply Although drain connection may vary depending on your circumstances a typical installation is shown at left After the tub has been located over the exist ing drain a stub is run up from the existing drain in the floor A threaded coupling is placed over the stub followed by a compression ring Then the threaded coupling is screwed ont
16. re If an electrical component related to a bathroom fixture fails the customer must utilize the services of a licensed electrician or electrical contractor to verify this warranty claim Any costs associated with the aforementioned testing requirement remain the client s full financial responsibility If an installer has any questions prior to installation Allure asks the client to contact the tech department Monday Friday 8 30am 4pm PST Allure s Warranty Policy does not cover superficial fixtures and surfaces It is the customer s responsibility to inspect a delivered product within 24 hours of receipt If superficial damage is discovered Allure must be notified by phone 877 629 5503 Additionally this damage claim must carry accompanying digital photographic images displaying said damage If this damage claim is not filed within 24 hours of receipt the customer will be responsible for the price of the part and variable shipping rate 24 hours represents the standard period to file concealed damage claims with LTL and specialty shipping companies used by Allure Allure maintains a parts department and associated parts in stock Parts are shipped Monday Friday during regular shipping hours 10am 3pm PST Standard parts are shipped standard ground Larger parts are shipped via LTL freight If the customer chooses to expedite the shipment of an in stock part he or she is responsible for the associated variable fee If a part is on backorder
17. ust circulate through the heater for it to be effective WATER JET FUNCTION NOTE Ensure that the water level in the tub is above the sensors and water jets in the back rest see illustration If water level is too low overspray may occur or the water pump may not function This is a safety feature designed to prevent damage to the water pump CORRECT WATER LEVEL WATER LEVEL TOO LOW JETS FUNCTION CORRECTLY OVERSPRAY FROM JETS Rea hee sap a MPR WATER LEVEL TOO LOW JETS WILL NOT FUNCTION The sensors for the Water Pump are the small silver studs located beneath the water jets on the seat backrest AIR JET SYSTEM The Air Jet system injects air into the bath from a number of fittings to create a soothing massage The air jets can be run in conjuction with the water jets or separately NOTE After every bath and after the bathtub has been drained the air jets should be run for 1 to 2 minutes whether they were used during the bath or not This will clear the lines and prevent mildew CLEANING AND CARE The water and air jet systems should be cleaned before first use and on a monthly basis afterwards while the bathtub is in normal use WATER JET SYSTEM Jetted Bathtubs Only 1 Fill the tub with WARM water 2 3 inches above the jets Add 1 4 to 1 2 box of baking soda to the bathtub water Turn on jet massage system and run for 10 minutes Drain tub Fill tub with COLD water 2 3 inches a
Download Pdf Manuals
Related Search