Bullet Tools 226 Use and Care Manual
Contents
1. cam snaps into place or out of place to disengage Repeat steps 2 4 for the other lobe WARNING Blade is very sharp Keep fingers away from blade Most materials listed on page 7 shear cleanly with just one cut However some types of laminate flooring and fiber cement siding may require cutting twice to produce a better cut DOUBLE CUTTING Simply make your first cut 1 8 to 1 4 3mm to 6mm longer than your mark and then make a second cut on your mark This is very useful to create a cleaner cut on exposed ends or when you cannot cover the cut edge with molding or trim 6 Your EZ Shear cuts a wide variety of products Please refer to this cut guide for recommended products and thicknesses SST CUT GUIDE Maximum Thickness 25mm or 1 Material Siding Fiber Cement Board Siding Pressboard Lap Siding Wood Trim OSB Trim Fiber Cement Trim Vinyl Shingles Tar or Wood Engineered Wood Commercial Vinyl Luxury Vinyl Tile Parquet Permastone PVC Tile Rubber Cove Base Rubber Tile Soft Plastic Please note Approved materials may vary in density and hardness If extreme pressure is required to cut a product it may result in damage to your machine Please contact Bullet Tools before proceeding Warranty is void ifan unapproved product damages the machine Do NOT Use on High Pressure Laminate or Solid Wood Replacement Blade for SST220 is part 220B Replacement Blade for SST226 is part2. 226B Special Soft Product Blade for SST220 is part 220SP Special Soft Product Blade for SST226 is part 226SP MAINTENANCE Honing the Blade Hone every 100 cuts Push the handle down until blade is 1 4 6mm open Lay the hone stone against the flat face of the blade side toward the table Slide from end to end 2 or 3 times This removes the small burr formed when cutting hard products Lubricating After every 100 cuts it is recommended that you lubricate the wear points of the pins and the bearings as shown Use a light oil i e 10W motor oil This will prevent the machine from wearing out prematurely Apply grease wheel bearing grease frequently to the bearings where indicated ACCESSORIES All Angle Fence ltem 701AF Set any angle from 0 to 90 Shear Stand Item 709 Allows you to cut with the shear off the ground WARRANTY 30 Day Satisfaction Guarantee Bullet Tools is confident that you will be absolutely pleased with the purchase of our product If for any reason you are not completely satisfied with your tool we will refund your purchase price at any time within 30 days of your original purchase receipt required If you want to return your product under our 30 day no risk trial offer valid only for purchases made in the US please contact us at 1 800 406 8998 or 208 772 0175 for return instructions BULLETPROOF WARRANTY SILVER 1 Year Bullet Tools warrants only to
3. USER GUIDE Read Before Use IGS T Make the Cut SST226 Do not use on High Pressure Laminate or Solid Wood o BULLEI IUULS S Cutting Edge Tool Solutions for Tradesmen www BulletTools com 208 772 0175 PRT INS 0220 RevB 05 13 2013 Bullet Tools Decks An Onis O sobs ee AWARNING VERY SHARP BLADE WARNING FAILURE TO FOLLOW THIS GUIDE MAY RESULT IN SERIOUS INJURY USING THIS MACHINE WITH RESPECT AND CAUTION WILL CONSIDERABLY REDUCE THE RISK OF PERSONAL INJURY SAFETY GUIDE FOR THE EZ SHEAR SST SERIES READ AND UNDERSTAND THIS INSTRUCTION MANUAL BEFORE OPERATING THE EZ SHEAR If you are not thoroughly familiar with the operation of the EZ Shear obtain advice from a qualified instructor or call 800 406 8998 Intl 208 772 0175 Stay alert Do not operate while under the influence of drugs alcohol or medication Always wear safety approved eye protection with side shields ANSI Z87 1 Keep work area clean and free of debris Recommended operating temperature range 20 F 6 C to 115 F 46 C Keep children and unauthorized persons away from the EZ Shear and work area Make sure tool is secure Operate only on a firm surface or solid stand Use the right tool Do not force the EZ Shear or use it for a job for which it was not intended the EZ Shear is designed to cut residential grade low pressure laminate flooring engineered wood flooring VCT PVC ti
4. crews 4 M6 Star Washers 4 6mm x 25mm PH Phillips Machine Screws 5 M6 x 16mm Phillips Machine Screws 4 10 x 1 Phillips Self Tapping Screws 2 M8 x 50mm Hex Bolts You will need 2 amp 3 Phillips head screwdrivers rt 3 N io 1 Power Assembly in I D nga w i 2 Handle Assembly 3 Fence Assembly 4 Table 5 Tail 6 Rails 4 7 Hone Stone 8 Mounting Bracket 4 9 HARDWARE KIT 226 HARDWARE KIT A oo p hum B O E pomm C jem Finis 8 6mm x 65mm PH Phillips Machine Screws 8 M6 Star Washers 8 6mm x 25mm PH Phillips Machine Screws 6 M6 x 16mm Phillips Machine Screws 4 10 x 1 Phillips Self Tapping Screws 2 M8 x 50mm Socket Head Cap Screws 1 M6 Allen Wrench ASSEMBLY 1 ATTACH RAILS 2 ATTACH TAIL Attach rails and mounting bracket to Power Assembly Attach tail and mounting bracket to rails using base using Item A machine screws fitted with Item B Item C machine screws Make sure holes in tail are star washers facing up 3 ATTACH TABLE A Attach table to base starting with front start screws with hand use tem D screws B Attach back of table to tail using Item E self tapping screws Tighten with 2 Phillips 4 TO ATTACH HANDLE For 220 Insert tem F screws and tighten with 1 2 wrench For 226 Insert Item F screws through back stroke stop and tighten with tem G hex wrench Note To ensure correct alignment start each of the bolt
5. ied are void with any alterations to the product Note Bullet Tools shall not be liable for any special incidental or consequential damages including but not limited to lost revenue lost profits rental or replacement equipment downtime damage to property and third party claims arising out of any theory of recovery including warranty contract statutory or tort Recommended hardness cut limit on J a n ka H a rd n es S S ca le Engineered Wood flooring Recommended hardness cut limit on Note Due to extreme variations in wood density your shear may or may not cut the products listed below with the EZ Shear Engineered Wood flooring with the Magnum Shear DO NOT CUT High Pressure Laminate Flooring OR Engineered Wood with a veneer thicker than 1 16 with the EZ Shear Recommended hardness cut limit on Solid Wood flooring with the Magnum Shear H ueanpY uot EE oomp i poyeN Read Before Use USER GUIDE Keep for Reference www BulletTools com 1 208 772 0175
6. le vinyl tile fiber cement board siding vinyl siding amp pressboard lap siding See Cut Guide page 6 Keep Blade sharp A dull Blade will not perform properly Always keep hands away from Blade while operating or carrying Do not alter or misuse this tool The EZ Shear is precision built modifications not specified in this manual may result in a dangerous condition Maintain EZ Shear with care Keep Blade sharp and clean Follow instructions for lubricating and changing accessories See page 6 Use only recommended accessories The use of improper accessories may cause hazards or injury Never leave the EZ Shear unattended Secure the Handle with the Safety Lock when not in use See page 5 Warning The dust generated by cutting certain wood wood fiber and or PVC products can be hazardous to your health The EZ Shear generally does not produce any dust however minimal creation of dust may be possible Avoid ingesting any dust created through cutting SST220 SET UP Please Review and Verify Parts Included in Box 1 Power Assembly 1a Safety Lock pin 2 Handle Assembly 3 Fence 4 Table 5 Tail 6 Rails 2 7 Hone Stone 8 Mounting Bracket 4 9 HARDWARE KIT SST226 SET UP Please Review and Verify Parts Included in Box 1a Safety Lock pin You will need 2 amp 3 Phillips head screwdrivers and a 1 2 13mm socket or wrench 4 6mm x 60mm PH Phillips Machine S
7. s by hand before using wrench AN AWARNING 5 PLACE THE FENCE For 220 Your EZ Shear is equipped with an aluminum fence which may be set to common roof pitches 4 12 6 12 8 12 and 12 12 Simply align with desired position and press pins into place Note The fence is friction fit requires effort to insert or remove For 226 Slide fixed clamp into the front quick alignment notch For 90 cuts slide loose clamp into rear alignment notch and tighten star knob For angle cuts 1 Align edge of fence with the desired angle guide mark in center of table 2 Slide loose clamp to edge of table and tighten knob MAKING CUTS While gently pushing handle down pull Safety Lock Pin out then lift handle Place product on table Bring handle down until blade Push the handle touches material down until ia the material is completely cut 7 A AIA 1 2 3 4 The 226 Shear has two Leverage Modes Mode 1 Use the long stroke cams black lobes only for lightweight products thicker than 1 2 inch Mode 2 For all other recommended products use the short stroke cams grey lobes Leverage Switch Instructions Engaging the Short Stroke Cams Remove any obstructions from under the blade Push handle to the closed position O Ensure that the camlock pin is disengaged Apply pressure to the lever of one of the short stroke cams grey lobes and let the handle up slowly until the
8. the original purchaser of this product when purchased from an authorized reseller or distributor that this product will be free from defects in material and workmanship under normal use and service for one 1 year from initial purchase This warranty includes all parts except the blade and cosmetic appearance chips dings scratches caused by normal use and wear This warranty does not cover any damage due to accident misuse abuse or negligence Further it is valid only if the product is used with the cut products specified in the cut guide Please refer to the User Guide for details or call Bullet Tools technical support In order to recover under this limited warranty the purchaser must make claim to Bullet Tools within 60 days of occurrence and must present acceptable proof of original ownership such as original receipt warranty card registration on line registration or other documentation Bullet Tools deems acceptable for the product Bullet Tools at its option shall repair or replace the defective unit covered by this warranty To obtain warranty service please contact Bullet Tools at 1 800 406 8998 or 1 208 772 0175 for pre authorization and further instructions Bullet Tools disclaims all warranties express or implied including all warranties of merchantability and or fitness for a particular purpose Additional rights may be available under the laws of your state or province Any and all warranties written or impl
Download Pdf Manuals
Related Search