GE 45603 Installation Guide
Contents
1. may cause undesired operation of the device Important Note To comply with the FCC RF exposure compliance requirements no change to the antenna or the device is permitted Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user s authority to operate the device Compliance with IC Rules and Regulations IC 6924A 45602A3 Jasco Products Company Model 45603 ZW4101 This Class B digital device complies with Canadian ICES 003 SPECIFICATIONS Power 120VAC 60Hz Signal Frequency 908 42 MHz Maximum load for both outlets 15 Amps 1800W Resistive Maximum load for the Z Wave controlled outlet 600W Incandescent Y HP Motor or 1800W Resistive Range Up to 100 feet line of sight between the Wireless Controller and the closest Z Wave receiver module Operating Temperature Range 32 104 F 0 40 C For indoor use only Specifications subject to change without notice due to continuing product improvement Z Wave is a registered US trademark of Sigma Designs 2011 JASCO Products Company Distributed by Jasco Products Company LLC 10 E Memorial Road Oklahoma City Oklahoma 73114 Made in China Hecho en China All brand names shown are rademarks of their respective owners Todas las marcas que aparecen aqui son marcas registradas de sus respectivos duefios 45603WB rev 12 14 112. JASCO 45603WB Wireless Lighting Control Fluorescent amp Appliance Module ANN A Swany Z Waveo Certified Wireless Lighting Control Introduction Thank you for your purchase of a Jasco Z Wave control device Z Wave technology is designed to automate lighting home control and provide easy remote operation of all your Z wave enabled devices The Jasco Z Wave product family includes a variety of devices to control lighting in your home It is up to you whether you want to control one room or your entire house and whether you want to do it all now or start with one room and add more over time This module is one component of a Z Wavee control system and is designed to work with all other Z Wave enabled devices in a home control network It will also act as a wireless repeater to insure that commands intended for another device in the network are received thereby extending the range of the wireless controller Z Wave devices of other types and brands can be added to the system and will also act as range extenders if they support this function of repeating the signal received to other nodes in the system The device plugged into the Z Wave controlled outlet on this module must not exceed 600 watts Incandescent 1800W 15A Resistive or Y HP Motor Total load capacity for both outlets is 1800W 15A Resistive There are no user serviceable parts in this unit Manual Program button St
3. andard AC outlet Z wa ve outlet other end To reduce the risk of electric shock this product has a grounding type plug that has a third grounding pin This plug will only fit into a grounding type power outlet If the plug does not fit into the outlet contact a qualified electrician to install the proper outlet Do not change the plug in any way WARNING RISK OF FIRE RISK OF ELECTRICAL SHOCK RISK OF BURNS Controlling Appliances Exercise extreme caution when using Z Wave devices to control appliances Operation of the Z Wave device may be in a different room than the controlled appliance also an unintentional activation may occur if the wrong button on the remote is pressed Z Wave devices may automatically be powered on due to timed event programming Depending upon the appliance these unattended or unintentional operations could possibly result in a hazardous condition For these reasons we recommend the following 1 Assign Z Wave controlled appliances to device numbers 10 18 on the Jasco remote The likelihood of unintentionally urning on the appliance will be reduced significantly because the Shift button will need to be pressed before pressing device numbers 10 18 Z Wave devices controlling appliances should be removed rom All control setting Instructions on how to do this are included in the manual for your Jasco remote Do Not include Z Wave devices in Groups or Scenes if they control ap
4. er indicates the action was unsuccessful please repeat the procedure Once the module is part of the network the same basic procedure is used to add the module to groups or scenes Refer to the primary controller s instructions for details Please Note After a power failure the 45603 module returns to its last used ON OFF state ADVANCED OPERATION The following Advanced Operation parameters require that you have an advanced controller like the model 45601 LCD remote Advanced remotes from other manufacturers may also be able to change these settings however basic remotes do not have this capability All On All Off Depending upon your primary controller the 45603 module can be set to respond to ALL ON and ALL OFF commands in up to four different ways Some controllers may not be able to change the response from its default setting Please refer to your controller s instructions for information on whether or not it supports the configuration function and if so how to change this setting Restoring Factory Defaults All Configuration Parameters can all be restored to their factory default settings by using your primary controller to reset the device delete it from network Over Current Protection Over current protection is provided by an internal fuse which is not user serviceable Check your home s circuit breakers before concluding that the product must be replaced Interoperability with Z Wave Devices A Z Wave netw
5. in to the upper outlet of a duplex wall receptacle This assumes that the duplex receptacle is mounted with the ground pin down Plugs and cords for connected devices route to the side al lowing close placement of furniture 4 Grounded 3 wire power connection for safety Basic Operation The connected light can be turned ON in two ways 1 With a Z Wave remote 2 Manually with the push button on the Z Wave module Remote Control Jasco Z Wave remotes provide control of an Individual de vice Groups of devices and Scenes Other brands of Z Wave Certified remotes may not offer as much flexibility in how you can set up your lighting control network Please refer to your remote control s instructions for details on its capabilities and instructions for adding and controlling devices Manual Control The Front Panel Push button on the 45603 Appliance Module allows the user to 1 Manually turn the connected equipment ON or OFF by pressing the button This is a toggle switch if the device is OFF pressing the button turns the device ON and vice versa 2 Include or exclude the module from the Z Wave home control network with your primary controller Refer to the instructions for your primary controller to access the network setup function and include or exclude devices When prompted by your primary controller tap the button The primary controller should indicate that the action was successful If the controll
6. metal box blocks a large part of the RF signal Effects of Home Construction on Wireless Range Between Z Wave Enabled Devices Note The distances shown in the table below are typical examples Actual performance in your home will vary From the Remote or repeating Z Wave module to destination device Type of Construction Wood Frame Brick Tile or w Drywall Concrete Plastic Metal Plastic Metal J Boxes J Boxes J Boxes J Boxes 0 100 80 100 80 Number 7 i P of Walls or 1 70 56 60 48 Obstacles 2 49 39 36 29 3 34 21 21 17 unction For Plug in Modules or In Wall Devices Installed in Plastic J Boxes Line of Sight no obstructions Please Note Z Wave home control networks are designed to work properly alongside 802 11 wireless computer networks Bluetooth and other 2 4GHz or 5 8GHz devices Some baby cams wireless video devices and older cordless phones using the 900MHz frequency range may cause interference and limit Z Wave functionality Many 900MHz products have a switch to select channel A or B You may find that one of these channels will cause less interference than the other Key Features 1 One Z wave controlled AC outlet Remote ON OFF control via the Z Wave controller Manual ON OFF control with the front panel push button 2 One Always ON pass through AC outlet 3 Space efficient design Does not block the lower outlet when plugged
7. ork can integrate devices of various classes and these devices can be made by different manufacturers Although every Z Wave certified product is designed to work with all other Z Wave certified products your controller must include the appropriate device classifications in order to control non lighting Z wave devices As an example the 45600 basic remote is designed only for controlling Z Wave devices using the lighting control classification The 45601 deluxe remote with LCD readout can control other Z Wave certified devices like thermostats as well as lighting WARRANTY JASCO Products warrants this product to be free from manufacturing defects for a period of two years from the original date of consumer purchase This warranty is limited o the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this product This warranty is in lieu of all other warranties expressed or implied Some states do not allow limitations on how long an implied warranty lasts or permit the exclusion or limitation of incidental or consequential damage so the above limitations may not apply to you This warranty gives you specific rights and you may also have other rights which vary from state o state Please contact Customer Service at 800 654 8483 option 4 between 7 30AM 5 00PM CST or via our website www ascoproducts com if the unit should prove defective within the
8. pliances Do Not use Z Wave devices to control electric heaters or any other appliances which may present a hazardous condition due to unattended or unintentional or automatic power on control Double check programs for accuracy before using them NOT FOR USE WITH MEDICAL OR LIFE SUPPORT EQUIPMENT Z Wave enabled devices should never be used to supply power to or control the On Off status of medical and or life support equipment Wireless Range This device complies with the Z Wave standard of open dir line of sight transmission distances of 65 feet Actual performance in a home depends on the number of walls between the remote controller and the destination device the type of construction and the number of Z Wave enabled devices installed in the control network Jasco Z Wave Network Every Z Wave enabled device acts as a signal repeater and multiple devices result in more possible transmission routes which helps eliminate RF dead spots Things to consider regarding RF range Each wall or obstacle i e refrigerator big screen TV etc between the remote or a Z Wave device and the destination device will reduce the maximum range by approximately 25 30 Brick tile or concrete walls block more of the RF signal than walls made of wooden studs and plasterboard drywall Wall mounted Z Wave devices installed in metal junction boxes will suffer a significant loss of range approximately 20 since the
9. warranty period JASCO Products Company Building B 10 E Memorial Rd Oklahoma City OK 73114 FCC U2245602 3 The Federal Communication Commission Radio Frequency Interference Statement includes the following paragraph The equipment has been tested and found to comply with the limits for a Class B Digital Device pursuant to part 15 ofthe FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment uses generates and can radiate radio frequency energy and if not installed and used in accordance with the instruction may cause harmful interference to radio communication However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Operation is subject to the following two conditions This device may not cause interference and This device must accept any interference including interference that
Download Pdf Manuals
Related Search