Rust-Oleum Automotive 249340 Use and Care Manual
Contents
1. release lead dust LEAD IS TOXIC EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS SUCH AS BRAIN DAMAGE ESPECIALLY IN CHILDREN PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE Wear a NIOSH approved respirator to control lead exposure Clean up carefully with a HEPA vacuum and a wet mop Before you start find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1 800 424 LEAD or log on to www eps gov lead PRODUCT APPLICATION cont APPLICATION Shake can vigorously for one minute after the mixing ball begins to rattle If mixing ball fails to rattle DO NOT STRIKE CAN Contact Rust Oleum Shake often during use Hold can 8 12 from surface and spray in a steady back and forth motion slightly overlapping each stroke Keep the can the same distance from the surface and in motion while spraying Apply 2 or more light coats a few minutes apart Do not use near open flame DRY amp RECOAT Dry and recoat times are based on 70 F 21 C and 50 relative humidity Allow more time at cooler temperatures Dries to the touch in 30 minutes and dries to handle in 1 2 hours High Heat Primer may be coated with Rust Oleum High Heat Paint anytime after 1 hour Once dry High Heat Paint or Primer must be further cured to increase durability Allow High Heat Paint and Primer to dry 2 4 hours before proceeding to the next steps below Follow directions accordingly Items may emit smoke and harmless odor at fir2. Pp TECHNICAL DATA ATO 56 HIGH HEAT PRIMER DESCRIPTION AND USES Rust Oleum High Heat Primer bonds to bare metal and helps create a smooth surface for top coat application It is formulated to prevent rust and is recommended for use on automotive engines and other automotive surfaces which reach intermittent temperatures up to 2000 F 1093 C For maximum protection top coat with Rust Oleum High Heat Paint High Heat Primer features an advanced spray system that allows you to spray at any angle even upside down for those hard to reach areas A comfort spray tip with a wider finger pad reduces fatigue caused by continuous spraying PRODUCTS SKU 12 ounce spray Description 249340 Gray PRODUCT APPLICATION PAINTING CONDITIONS Use outdoors or in a well ventilated area such as an open garage Use when temperature is between 50 90 F 10 32 C and humidity is below 85 to ensure proper drying Do not apply to galvanized metal Do not use on metal directly exposed to flames Avoid spraying in very windy and dusty conditions Cover surrounding area to protect from spray mist SURFACE PREPARATION Wash the surface with a commercial detergent or other suitable cleaning method Rinse with fresh water and dry with a clean cloth Remove loose paint and rust with a wire brush or sandpaper until the metal surface is completely bare Lightly sand smooth and glossy surfaces WARNING If you scrape sand or remove old paint you may
3. age Dry Heat Resistance 2 000 F 1093 C Intermittent Shelf Life 5 years Flash Point 156 F 104 C Safety Information For additional information see MSDS The technical data and suggestions for use contained herein are correct to the best of our knowledge and offered in good faith The statements of this literature do not constitute a warranty express or implied as to the performance of these products As conditions and use of our materials are beyond our control we can guarantee these products only to conform to our standards of quality and our liability if any will be limited to replacement of defective materials All technical information is subject to change without notice ge RUST OLEUM BRANDS Rust Oleum Corporation Form GDH 109 11 Hawthorn Parkway Phone 877 385 8155 Rev 071613 Vernon Hills Illinois 60061 www rustoleum com An RPM Company
4. st when heated Items Off Vehicle Bake at 250 F 121 C for 30 minutes then allow 30 minutes to cool Bake at 400 F 204 C for 30 minutes then allow 30 minutes to col Bake at 600 F 315 C for 30 minutes then allow 30 minutes to cool Caution Be sure not to exceed the heat tolerance of the least heat tolerant part Items On Vehicle Run vehicle at idle for 10 minutes then allow 20 minutes to cool Run vehicle at idel 20 minutes then let cool for 20 minutes Run vehicle at normal operating conditions for 30 minutes then allow vehicle to cool CLEAN UP Wipe off tip when finished Clean up wet paint with xylene or mineral spirits Properly discard empty container Do not burn or place in home trash compactor CLOGGING If the valve clogs twist and pull off spray tip and rinse ina solvent such as mineral spirits Do not insert any object into can valve opening Form GDH 109 Rev 071613 TECHNICAL DATA HIGH HEAT PRIMER PHYSICAL PROPERTIES HIGH HEAT PRIMER Resin Type Proprietary Pigment Type Titanium Dioxide Copper Chromite Black Solvents Acetone Toluene Xylene MIR 1 70 Max Fill Weight 12 ounces Recommended Dry Film Thickness DFT Per Coat 1 5 2 5 mils 37 5 62 5p Practical Coverage at Recommended DFT 10 12 sq ft can 0 90 1 09 m can Dry Times Touch 30 minutes and 50 Relative Handle enous Humidity Cure See instructions on previous p
Download Pdf Manuals
Related Search