Rust-Oleum Specialty 7750830 Use and Care Manual
Contents
1. TECHNICAL DATA SPC 29 TRUSTED QUALITY SINCE 1921 RUST OLEUM We as HIGH HEAT ULTRA SPECIALTY DESCRIPTION AND USES High Heat Ultra is a rust preventive enamel designed to provide deep color and rich sheen to protect indoor and outdoor high heat applications This durable semi gloss finish retains excellent gloss and color retention after repeated heating High Heat sprays withstand temperatures up to 1200 F 648 C Ideal for the exterior of barbeque grills wood stoves radiators fire pits fireplace screens automotive parts and more PRODUCTS 241169 Black 241230 Brown 241232 Aged Copper 270201 Silver PAINTING APPLICATION PAINTING CONDITIONS Use outdoors or in a well ventilated area such as an open garage Use when temperature is between 50 F 10 C and 90 F 32 C and humidity is below 85 to ensure proper drying Priming is not recommended Do not use on metal directly exposed to open flame or in direct contact with food such as a grill grate Avoid application in very windy and dusty conditions Cover surrounding area to protect from spray mist SURFACE PREPARATION Remove all dirt grease oil salt and chemical contaminants by washing the surface with a commercial detergent or other suitable cleaning method Rinse with fresh water and allow to thoroughly dry Remove loose paint and rust with a wire brush or sandpaper Previously coated surfaces must be sound and in good condition Smooth hard or gl2. mineral spirits Do not insert any object into can valve opening Form CS1715 Rev 110912 TECHNICAL DATA TRUSTED QUALITY SINCE 1921 RUST OLEUM SPECIALTY SPECIALTY HIGH HEAT ULTRA PHYSICAL PROPERTIES High Heat Ultra Resin Type Modified Silicone Pigment Type Black Manganese Ferrite Chromite Black MIR 1 20 Max Fill Weight 12 ounces Solvents Acetone and Aromatic Hydrocarbons Recommended Dry Film 1 0 2 0 mils Thickness DFT per Coat 25 50u Practical Coverage at Recommended DFT assumes 15 material loss 7 8 sq ft can 0 63 0 72 m can Dry Times at 77 F 25 C and 50 Relative Humidity Touch 30 minutes Handle 1 2 hours Recoat Within 1 hour or after 48 hours Full Cure Allow paint to dry 1 hour before heating Dry Heat Resistance 1200 F 648 C Shelf Life 5 years Flash Point 156 F 144 C Warning For additional information see MSDS The technical data and suggestions for use contained herein are correct to the best of our knowledge and offered in good faith The statements of this literature do not constitute a warranty express or implied as to the performance of these products As conditions and use of our materials are beyond our control we can guarantee these products only to conform to our standards of quality and our liability if any will be limited to replacement of defective materials All technical info
3. ossy finishes should be scarified by sanding to create a surface profile Removal of old paint by sanding scraping or other means may generate dust or fumes that contain lead LEAD IS TOXIC Contact the U S EPA Lead Information Hotline at 1 800 424 LEAD or log on to www epa gov lead APPLICATION Shake can vigorously for one minute after the mixing ball begins to rattle If mixing ball fails to rattle DO NOT STRIKE CAN Contact Rust Oleum Shake often during use Hold can upright 10 160from surface and spray in a steady back and forth motion slightly overlapping each stroke Keep the can the same distance from the surface and x5in motion while spraying Apply two or more light coats a few minutes apart to avoid drips and runs Do not use near open flame PRODUCT APPLICATION cont DRY amp RECOAT TIMES Dry and recoat times are based on 70 F and 50 relative humidity Allow more time at cooler temperatures Dries to touch in 30 minutes and to handle in 1 2 hours Allow paint to dry for 1 hour before heating Product may emit smoke and harmless odor May recoat within 1 hour or after 48 hours CLEAN UP Clean valve immediately after use by turning can upside down and depressing spray button for 3 5 seconds Clean up wet paint with xylene or mineral spirits Properly discard empty container Do not burn or place in home trash compactor CLOGGING If the valve clogs twist and pull off spray tip and rinse in a solvent such as
4. rmation is subject to change without notice se RUST OLEUM BRANDS Rust Oleum Corporation Form CS1715 11 Hawthorn Parkway Phone 877 385 8155 Rev 110912 Vernon Hills Illinois 60061 www rustoleum com An RPM Company
Download Pdf Manuals
Related Search