Zinsser 4304 Use and Care Manual
Contents
1. dust dirt grime and other contaminants that can interfere with adhesion Rinse well and let dry before patching Remove any poorly adhering existing coatings by sanding and or scraping Remove loose dried caulk and replace where necessary Note Very deep holes requiring an epoxy based wood filler or concrete cement patch should be filled with these materials Areas that are normally caulked should be filled with the proper caulking material Countersink exposed nail heads and prime with an appropriate stain killing primer PRODUCT APPLICATION cont APPLICATION Apply when air and surface temperatures are between 50 90 F 10 32 C and the relative humidity is below 95 Higher temperatures and lower humidity will accelerate the dry time and cure time of the product while lower temperatures and higher humidity will slow down the dry time and cure time Ready Patch should be applied with a clean putty or spackling knife Use a 1 putty knife for nail holes and cracks or a 2 knife for larger gouges Spread Ready Patch over the hole and remove excess until product is smooth and flush with the surface Apply as many coats as necessary to fill the hole or imperfection level with the Surrounding surface If holes are wide and over deep two or more applications are recommended Ready Patch Lite may be primed or painted when dry to the touch Otherwise wait until product has fully dried before sanding smooth Prime patched area2. in good faith The statements of this literature do not constitute a warranty express or implied as to the performance of these products As conditions and use of our materials are beyond our control we can guarantee these products only to conform to our standards of quality and our liability if any will be limited to replacement of defective materials All technical information is subject to change without notice a Rust Oleum Corporation Form GDH 241 RUST OLEU M 11 Hawthorn Parkway Phone 877 385 8155 Rev 120913 Vernon Hills Illinois 60061 www rustoleum com BRANDS An RPM Company
3. oo TECHNICAL DATA RPH 02 ZINSSER ZINSSER e QUALITY SINCE 1849 READY PATCH LITE DESCRIPTION AND USES Ready Patch Lite is a vinyl acrylic compound designed for filling cracks holes gouges and surfaces imperfections on walls doors cabinets furniture siding fascia soffits foundations and related interior and exterior architectural substrates Ready Patch Lite is recommended for filling nail holes splits cracks gouges dents and other imperfections in new or previously painted wood including pine fir cedar redwood plywood T 1 11 and pressure treated wood drywall cured plaster masonry including stucco concrete block poured concrete and brick Ready Patch Lite is not intended as a substitute for concrete cement patch caulk or epoxy wood filler or for use in circumstances where these products are required nor is it recommended for application to any surface subject to immersion or in prolonged contact with water PERFORMANCE CHARACTERISTICS Lightweight formula for quick easy repairs Recommended for interior or exterior Surfaces Dries quickly and sands easily Resists shrinking and cracking Can be painted when dry to the touch PRODUCTS SKU Container Size 4301 1 Gallon 4304 1 Quart 4308 1 Pint 4309 V2 Pint PRODUCT APPLICATION SURFACE PREPARATION Surfaces to be patched must be clean dry and in sound condition If necessary wash thoroughly with detergent and water to remove
4. s before painting to prevent excessive absorption of paint THINNING If thinning is necessary add water sparingly and stir thoroughly COLOR TINTING Ready Patch Lite is off white in color For applications where it is necessary to differentiate the color of the spackling paste from the color of the substrate add few drops of universal colorant and blend in thoroughly CLEAN UP Clean up excess or dropped portions of product while soft with a damp rag If product dries it may be removed by scraping sanding or washing Clean application tools in warm soapy water immediately after use If product has dried on application tools soak overnight in a solution of detergent and water Form GDH 241 Rev 120913 TECHNICAL DATA ZINSSER READY PATCH LITE Resin Type Vinyl Acrylic Pigment Type A Solvents Ethylene Glycol Water Weight 4 0 Ibs Per Liter 0 5 kg By Weight 45 0 By Volume 72 0 Volatile Organic Compounds lt 100 g l Practical Coverage at Recommended 13 sq ft gal at inch thickness DFT assumes 15 material loss Vary vary depending on depth and extent of the cavities being filled Dry Times at 70 Touch lave umity Mone Relative Humidity 1 hour 2 hours Storage 35 90 F 4 27 C Shelf Life 3 years gt 200 F 93 C Safety Information For additional information see MSDS The technical data and suggestions for use contained herein are correct to the best of our knowledge and offered
Download Pdf Manuals
Related Search