Zinsser 256260 Use and Care Manual
Contents
1. 1 Gallon 271198 1 Quart APPEARANCE BONDZ is white but may be tinted to off white and pastel shades to improve the hiding power of the topcoat by adding no more than 2 oz 59 ml universal colorant per gallon PRODUCT APPLICATION SURFACE PREPARATION Surfaces should be clean dry sound and free of any contamination mildew scaling paint loose rust heavy chalking excessive oil and other contaminants such as wax or wallpaper paste which will interfere with adhesion If unsure of cleanliness always wash surface with an appropriate cleaner or solvent DO NOT USE TSP Always test a small area for acceptable adhesion For general oil and water based stain blocking use a Zinsser stain blocking primer such as Zinsser Smart Prime or Zinsser Bulls Eye 1 2 3 Plus Spot prime knots and severe stains with Zinsser B I N Shellac based Primer Sealer before full surface priming with BONDZ WARNING If you scrape sand or remove old paint you may release lead dust LEAD IS TOXIC EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS SUCH AS BRAIN DAMAGE ESPECIALLY IN CHILDREN PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE Wear a NIOSH Approved respirator to control lead exposure Clean up carefully with a HEPA vacuum and a wet mop Before you start find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1 800 424 LEAD or log on to www epa gov lead MIXING Mix thoroughly to ensure any settl2. TECHNICAL DATA ZBZ 01 BONDZ MAXIMUM ADHESION PRIMER ZINSSER QUALITY SINCE 1849 DESCRIPTION AND USES Zinsser BONDZ is an acrylic bonding primer designed for priming difficult to paint surfaces Use on interior and exterior surfaces to promote maximum adhesion over building material plastics including PVC sheeting amp piping vinyl laminated Formica cabinets fiberglass awnings and garage doors tile glazed block and brick and non ferrous metals such as aluminum doors and window frames aluminum flashing and trim Kynar coated metals galvanized steel glossy oil based enamels drywall masonry glass paneling painted or unpainted wood and slightly chalky surfaces Apply any top coat finish including oil based enamels water based acrylics epoxies urethanes and lacquer This product is not recommended for application to floors decks surfaces subject to immersion or prolonged contact with water or below grade applications It is not recommended for use on polyethylene polypropylene Teflon or nylon surfaces DO NOT MIX WITH ANY OTHER PRIMER PERFORMANCE CHARACTERISTICS Bonds to all topcoats and hard dense surfaces May be used with all topcoats including solvent based and two component epoxies Topcoat in 1 hour with conventional paints in 6 hours with epoxies Excellent wet adhesion Very low odor and low VOCs e Easy soap and water clean up PRODUCTS SKU Unit Size 256260 5 gallon 256261
3. ed pigment is re dispersed DO NOT THIN APPLICATION Apply only when air material and surface temperatures are between 36 90 F 2 32 C and the surface temperature is at least 5 F 3 C above the dew point The relative humidity should not be greater than 85 Mix thoroughly to ensure any settled pigment is re dispersed before using In most cases only one coat is necessary to prime most surfaces If excessive absorption occurs over very porous substrates a second coat may be necessary Spot priming is recommended only under high hiding topcoat paints For best results prime entire surface before painting Apply with a natural or synthetic bristle brush roller pad or sprayer Follow manufacturer s instructions when using spray equipment For airless spraying use a 017 tip at 2000 to 2500 psi CLEAN UP Clean up spills and paint drips with warm soap and water Wipe up splatters before they dry Follow manufacturer s directions to clean spray equipment Dispose of unused or unwanted product in accordance with local laws regulating water based coatings Form CS2011 Rev 012513 TECHNICAL DATA ZINSSER BONDZ MAXIMUM ADHESION PRIMER PHYSICAL PROPERTIES nnn taximam eesion Primer Weight per Gallon 10 2 lbs Weight per Liter 1 22 kg Solids by Weight 45 6 Solids by Volume 33 2 Volatile Organic Compounds lt 100 g l 0 83 lbs gal Recommended Dry Film 1 0 2 0 mils Thickness DFT per Coat 25 50 Wet F
4. ilm to Achieve DFT Unthinned 3 0 6 0 mils material 75 150 Theoretical Coverage at 532 sq ft gal 1 mil DFT 25p 13 1 m l Practical Coverage at Approximately 400sq ft gal Recommended DFT assume 15 Depending on application method and surface porosity material loss Dry Times at 70 Touch 30 minutes 80 F 21 27 C and 50 Relative Humidity Light Sanding or 1 hour most paints Recoat 6 hours epoxies Storage and Handling Store indoors 40 90 F 4 32 C FlashPoint 0 ROO For additional information see MSDS The technical data and suggestions for use contained herein are correct to the best of our knowledge and offered in good faith The statements of this literature do not constitute a warranty express or implied as to the performance of these products As conditions and use of our materials are beyond our control we can guarantee these products only to conform to our standards of quality and our liability if any will be limited to replacement of defective materials All technical information is subject to change without notice rT Rust Oleum Corporation Form CS2011 RU ST OLE U M 11 Hawthorn Parkway Phone 877 385 8155 Rev 012513 Ze Vernon Hills Illinois 60061 www rustoleum com BRANDS An RPM Company
Download Pdf Manuals
Related Search