Rust-Oleum Automotive 260771 Use and Care Manual
Contents
1. can Dry Times at 70 80F Touch 30 minutes 21 27 C and 50 Relative Humidity Handle KERo Recoat Anytime after 1 hour Dry Heat Resistance 2 000 F 1 093 C Shelf Life 3 years Flash Point 156 F 104 C Safety Information For additional information see MSDS The technical data and suggestions for use contained herein are correct to the best of our knowledge and offered in good faith The statements of this literature do not constitute a warranty express or implied as to the performance of these products As conditions and use of our materials are beyond our control we can guarantee these products only to conform to our standards of quality and our liability if any will be limited to replacement of defective materials All technical information is subject to change without notice ma RUSTOLEUM BRANDS Rust Oleum Corporation Form GDH 428 11 Hawthorn Parkway Phone 877 385 8155 Rev 081114 Vernon Hills Illinois 60061 www rustoleum com An RPM Company2. ate a surface profile WARNING If you scrape sand or remove old paint you may release lead dust LEAD IS TOXIC EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS SUCH AS BRAIN DAMAGE ESPECIALLY IN CHILDREN PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE Wear a NIOSH approved respirator to control lead exposure Clean up carefully with a HEPA vacuum and a wet mop Before you start find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1 800 424 LEAD or log onto www epa govilead PRIMING Use of a Rust Oleum 249340 High Heat Primer provides added corrosion protection superior adhesion and hiding and is especially recommended for metal surfaces PRODUCT APPLICATION cont APPLICATION Shake can vigorously for one minute after the mixing ball begins to rattle If mixing ball fails to rattle DO NOT STRIKE CAN Contact Rust Oleum Shake often during use Hold can upright 8 12 from surface and spray in a steady back and forth motion slightly overlapping each stroke Keep the can in motion while spraying Apply 2 or more light coats a few minutes apart to avoid runs and sags Do not use near open flame DRY amp RECOAT Dry and recoat times are based on 70 F and 50 relative humidity Allow more time at cooler temperatures Dries to touch in 30 minutes and dries to handle in 1 2 hours You may recoat anytime after 1 hour Once dry High Heat must be further cured to increase durabili
3. po TECHNICALDATA CATON AUTOMOTIVE HIGH HEAT PAINT DESCRIPTION AND USES Rust Oleum High Heat is a tough protective enamel that renews and protects surfaces subject to intermittent heat up to 2 000 F 1093 C This rust preventive formula is ideal for automotive parts High Heat Enamels features an advanced spray system that allows you to spray at any angle even upside down for those hard to reach areas A comfort spray tip with a wider finger pad reduces fatigue caused by continuous spraying PRODUCTS SKU Description 248903 Flat Black 248904 Flat Aluminum 248905 Flat Orange 248908 Flat Red 248909 Flat Blue 254858 Flat White 260771 Clear PAINTING APPLICATION PAINTING CONDITIONS Use outdoors or in a well ventilated area such as an open garage Use when temperature is between 50 F 10 C and 90 F 32 C and humidity is below 85 to ensure proper drying Do not use on metal directly exposed to flames Avoid spraying in very windy and dusty conditions Cover surrounding area to protect from spray mist SURFACE PREPARATION Remove all dirt grease oil salt and chemical contaminants by washing the surface with a commercial detergent or other suitable cleaning method Rinse with fresh water and allow to thoroughly dry Remove loose paint and rust with a wire brush or sandpaper Previously coated surfaces must be sound and in good condition Smooth hard or glossy finishes should be scarified by sanding to cre
4. ty Allow paint to dry 1 2 hours before proceeding to the next steps below Follow directions accordingly Items may emit smoke and harmless odor at first ITEMS OFF THE VEHICLE Bake at 250 F 121 C for 30 minutes and allow 30 minutes to cool Bake at 400 F 204 C for 30 minutes and allow 30 minutes to cool Bake at 600 F 315 C for 30 minutes and then allow 30 minutes to cool Caution Be sure not to exceed the heat tolerance of the least heat tolerant part ITEMS ON THE VEHICLE Run the vehicle at idle for 10 minutes and then allow 20 minutes to cool Run vehicle at idle for 20 minutes then let cool for 20 minutes Run vehicle at normal operating conditions for 30 minutes then allow vehicle to cool CLEAN UP Wipe off tip when finished Clean up wet paint with xylene or mineral spirits Properly discard empty container Do not burn or place in home trash compactor CLOGGING If the valve clogs twist and pull off spray tip and rinse ina solvent such as mineral spirits Do not insert any object into can valve opening Form GDH 428 Rev 081114 TECHNICAL DATA AUTOMOTIVE HIGH HEAT PAINT PHYSICAL PROPERTIES HIGH HEAT PAINT Resin Type Silicone Pigment Type Varies with color Solvents Aromatics and Ketones MIR 1 4 Max Fill Weight 12 ounces Recommended Dry Film 0 5 1 0 mils Thickness DFT Per Coat 12 5 25p Practical Coverage at Recommended DFT 6 10 sq ft can 0 6 0 9 m
Download Pdf Manuals
Related Search