Veranda 73012449 Installation Guide
Contents
1. m iens 5 Transferable Limited Lifetime Warranty What is covered Barrette Outdoor Living warrants vinyl and aluminum products to include vinyl and aluminum fence vinyl and aluminum railing and plastic lattice against defects or workmanship for as long as you own your home Barrette Outdoor Living will at its option replace the product in question with new product of the same or equivalent value at no charge Barrette Outdoor Living warrants these products against peeling flaking splintering corrosion rusting or abnormal discoloration under normal use and service per ASTMD 2244 This warranty extends to the original purchaser or transferee as specified herein on the products noted above Separate and distinct warranties for hardware and other products are not covered under this warranty What this warranty does not cover This limited warranty does not cover damage resulting from accident unreasonable use neglect alteration improper service improper installation acts of God or any other causes not arising out of defects in materials or workmanship Additionally this warranty does not cover costs of installation removal reinstallation or surface mold and mildew created by excessive environmental conditions Any service or repair provided outside the scope of this limited warranty shall be at Barrette Outdoor Living s rate and terms then in effect What do we do to correct the problems Should your Barrette Outdoor Living product pro2. e n m Barrel p For angled rail installation other than at 90 degrees or 180 degrees purchase left to right angle brackets Follow previous steps Install four 2 screws though the bottom of the top rail brackets into handrail Pre drill all four holes with a 5 32 drill bit Install the first two Screws straight 90 degrees through the pre drilled holes in the bottom of the bracket Install the next During step 2 install bases at respective heights two screws at 45 degrees through the brackets into instead oF dovetails the post starting with the dimples on the bottom of the top rail bracket During step 5 mark approximately 2 from the end of the post to allow for bracket clearance and expansion This distance may vary depending on individual installation After step 10 slide provided pins in top bottom angle brackets to lock angle brackets to base For Stair Railing This guide outlines installation methods for installing Premier Railing stair kits in a variety of angles It is very important to identify the angle of your stairs as the installation methods vary depending on what angle the stair is Within the following steps be sure to pay close attention to the placement and utilization of the stair angle template to ensure you mark and cut your rails correctly and note orientation of all brackets and railing in the supporting images Closely follow Post Install
3. Kit installation instructions or sleeve existing wood 4x4 with Post Jacket Temporarily secure a deck board 5 4 to your stair treads to determine the spacing between the nose of the stairs and your bottom rail Place bottom rail on board and center the routes between posts making sure to leave equal distance from baluster route to post on both top and bottom Mark the bottom rail using inside edge of posts eo Barreto G 5 Measure angle take rail to chop saw and measure angle Set saw and record angle NOTE Do not cut here This is for acquiring measurements e f angle is 31 33 then go to Step 5 e If angle is 355 then skip Step 5 and proceed to Step 6 e If angle is gt 33 then skip Step 5 and 6 and proceed to step 7 For angles 31 33 e From the original line created by the post mark another line 11 16 on the inside of the bottom rail closer to the baluster routes This is accomplished by using the angle template This additional removal of material will allow for bracket clearance when the rail is installed For this 31 33 angle the new line will be parallel to the previously drawn line Chop saw should already be set at 32 ORIGINAL LINE Cut the bottom rail on the new mark at a 32 31 33 NOTE If your cut will result in a baluster route hole being cut through repeat Step 3 and add subtract a baluster route hole PT EIU E d re center mark and proceed to Step 4 Go to S
4. Models gt B 34106887B0M V5 5 13 Barrette 9 Premier Railing m m 73012442 73012443 73012444 K 73012445 73012446 73012447 al r 73012448 73012449 73012450 73012451 73012452 73012453 Assembly and Installation Instructions 73013195 73013180 73013183 73013181 73013178 73013179 PLEASE READ OWNER S MANUAL COMPLETELY CIEL MEE 7 uke BEFORE ASSEMBLING YOUR RAILING KIT 73012457 73013184 73013182 Owner s Manual Version z j n E Please read these instructions carefully before installing your Barrette railing If you have any questions or issues installing the railing please contact us at 1 800 336 2383 Barrette Material Checklist for assistance O Tape Measure Level Before You Begin 2 O Hacksaw or Chopsaw Check your local zoning laws L1 Rubber Mallet e Local zoning laws and Home Owners Associations may L1 Drill regulate the location style and height of your fence or even O Drill bits require a permit signoff beforehand 182 square drive bit Contact your local utilities companies e You must have the utility companies clearly mark your property for electrical gas or water lines to avoid puncturing any ATTENTION Before you assemble the rail unseen underground utilities PLEASE TAKE A COMPLETE INVENTORY OF ALL PARTS USING THE KIT CONTENTS Pay to mark your property line DO NOT ATTEMPT TO ASSEMBLE THE RAIL IF PARTS ARE MISSING OR DAMAGED e Being pr
5. SHALL NOT BE LIABLE FOR ANY DAMAGES LOSS OF USE LOSS OF PROFITS OR INTERRUPTION OF BUSINESS WHETHER SUCH ALLEGED DAMAGES ARE BASED IN WARRANTY TORT CONTRACT OR INDEMNITY SOME STATES DO NOT ALLOW THE EXCLUSION OF LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU This warranty is valid only in the United States and Canada Refer to www BarretteOutdoorLiving com for specific details about warranty limitations 1 800 336 2383 En Barrette Barrette Outdoor Living e 7830 Freeway Circle e Middleburg Heights Ohio e 44130 http www barretteoutdoorliving com e 1 800 336 2383 b 34106887B0M V5 5 13
6. oactive will save you time and money from any Please do not return the product to the store for assistance or replacement parts call disputes from neighbors 2013 Barrette Outdoor Living 1 800 336 2383 7830 Freeway Circle Middleburg Heights Ohio 44130 PERSON INSTALLATION RECOMMENDED For Railing Closely follow post install kit installation instructions or sleeve existing wood 4x4 Instructions included with post install kit sold separately Bracket Dovetail Installation With a 1 8 drill bit pilot drill the holes for the top and Install base trim over post sleeves first A bottom brackets as shown Remove template if used dl For 36 high rails place bracket dovetail install template against the post sleeve against the base trim and rubber band it in place For 42 high rails top bracket dovetail will install 37 75 from the top of base trim and bottom bracket dovetail will install 11 2 from top of base trim 36 Rails 42 Rails BT Aa TEMPLATE e n o Barrel p Cut Rails to Length Use 2 screws to attach top bracket dovetails f Screws must penetrate the steel insert if using F steel surface mount Use 1 7 screws to attach bottom bracket dovetails NEN Place bottom rail across post opening leaving equivalent spacing from the last baluster and post on each end Mark 1 2 from end
7. of post to allow room for bracket width and expansion Align top rail with bottom rail and cut both rails with miter box or hacksaw See blade manufacturers specs for correct blade Note You will have to cut through an aluminum insert in the top rail of an 8 section b support brace is included with 6 railing kits Measure equal distance from both ends of railing and install support brace in center of bottom rail For 67 rail install center of support brace 33 from ends of rail 2 support braces are included with 8 railing kits Measure length of rail divide by 3 and measure that distance from the end of our railing to the center of your first support brace and install support brace Repeat that step from the opposite side of your rail For 91 rail divide 9T by 3 307 install center of both support braces 30 from their respective ends gt T d A 331 3 SUPPORT BRACE 3 SUPPORT BRACE Re Barrette LL RR Assemble Railing Section Lay bottom rail on a clean smooth surface and snap balusters into routed holes Then repeat the process to connect the top rail i Slide brackets onto ends of rails top and bottom Hang Assembled Rail Section onto Dovetails For railing sections using aluminum balusters the installer will have to carefully hold top and bottom railings together to make sure f section does not separate Aluminum balusters do not come with lock tabs
8. on bracket l Set chop saw to stair angle and carefully cut all four brackets as shown Be particularly careful to cut from the proper side of feather to edge B 26 Top RAIL p A 25 h i 1 139 The cuts outlined above give you the results below The angle cut on the rail matches the inside of the bracket 32 The bracket outside cut matches the installation angle 33r 33 Once the brackets have been cut to the proper angle remove the screws from underneath the rails holding the brackets to the rails from Step 10 This allows the rails to float in the brackets during assembly gt n Barrel J Assemble your stair railing section a Lock tabs on baluster spindle must face outer edge of routed holes in rails b Assemble your stair section by snapping balusters spindles in rails Outer edge holes C Place brackets on ends d Place assembled stair rail between posts on spacer board Make sure rail brackets are centered on posts Drive two 10x2 mounting screws into brackets and into posts starting with the bottom rail Repeat for each bracket Screw holes are angled inwards to provide clearance for the drill chuck Removal of the bottom stair tread is not required Two screws 10x1 per bracket are driven under the top rail Holes are angled to allow an extension bit to clear balusters NOTE screws are not required in the bottom of the bottom rail
9. tep 8 MARK HERE 32 ORIGINAL LINE For angles 26 31 e From the original line created by the post mark another line 11 16 on the inside of the bottom rail closer to the baluster routes This is accomplished by using the angle template This additional removal of material will allow for bracket clearance when the rail is installed For this 26 3T angle the new line will NOT be parallel to the previously drawn line e Set chop saw at 32 e Cut the bottom rail on the new mark at a 32 EE RN S NOTE If your cut will result in a baluster route hole being cut through repeat Step 3 and add subtract a baluster route hole re center mark and proceed to Step 4 MARK HERE 32 The rail will not match the angle of the stair but instead match the inside of the bracket The outside of the brackets m will be cut to the proper angle in Step 11 MARK HERE 32 ORIGINAL LINE LESS THAN 31 Go to Step 8 For angles 34 38 e From the original line created by the post mark another line 11 16 on the inside of the bottom rail closer to the baluster routes This is accomplished by using the angle template This additional removal of material will allow for bracket clearance when the rail is installed For this 26 31 angle the new line will NOT be parallel to the previously drawn line e Set chop saw at 32 ORIGINAL LINE e Cut the bottom rail on the new mark at a 32 MORE THAN 33 dE NOTE If your cut will res
10. ult in a baluster route hole being cut through MARK HERE 32 repeat Step 3 and add subtract a baluster route hole re center mark and proceed to Step 4 The rail will not match the angle of the stair but instead match the inside of the bracket The outside of the brackets MARK HERE 32 will be cut to the proper angle in Step 11 ORIGINAL LIME MORE THAN 33 Go to Step 8 e n Barrel J Place top rail flat on table as shown Lay the cut bottom rail on top of the top rail with the routed holes facing in the same direction Line up the routes Bottom Rail M Mark the top rail using the bottom rail and a steel rule as a guide to the top edge of the rail as shown by the arrows Make sure to extend the line out at the angle to the edge of the rail mark line on bump of bottom of top rail on angle not straight down Cut the top rail to the lines using the chop saw set to 32 N CoRRECT INCORRECT s Make sure bottom of rails are flush against saw fence For angles 31 33 go to Step 12 For angles 26 31 and 33 38 go to Step 10 In Place brackets on bottom rail securing with 2 screws per bracket 10 x T as shown Then place brackets on top rail securing with 1 screw per bracket 10 x T as shown Barrette BorroM RAIL Top RAIL the bracket depending on your angle Cut smallest amount of bracket possible to get the correct angle
11. ve defective under warranty reference the website or call the phone number listed below Your problem will be assigned a tracking number and an authorized Barrette Outdoor Living representative will contact you to arrange a convenient time to schedule an onsite inspection or request pictures if need be If after inspection product is deemed to be manufacturer defect we will make arrangements to rectify the issue You must have proof of your purchase in order for the problem to be corrected Transferee Coverage Warranty coverage will be extended to one transferee on the above listed products with the following limitations Transferee must obtain an original or copy of the initial sales receipt with proof of date from the previous owner s Additionally if fence is purchased from a builder or installer documentation must be supplied that names the product installed on property and date of transfer THIS WARRANTY IS IN LIEU OF ALL CONDITIONS OR WARRANTIES EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO ANY IMPLIED CONDITIONS OR WARRANTIES OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THE PART OF Barrette OR ITS LICENSORS SOME STATES DO NOT ALLOW THE EXCLUSIONS OF IMPLIED WARRANTIES OR LIMITATIONS OF HOW LONG AN IMPLIED WARRANTY LASTS SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU IF THE PRODUCT IS DEFECTIVE PER THE ABOVE COVERAGES YOUR SOLE AND EXCLUSIVE REMEDY SHALL BE REPAIR OR REPLACEMENT AS PROVIDED ABOVE BARRETTE AND ITS LICENSORS
Download Pdf Manuals
Related Search