Ideal Pet 80VPPXLW Instructions / Assembly
Contents
1. Vinyl Patio Pet Door www idealpetproducts com For Standard amp Tall Vinyl Patio Pet Doors Before You Get Started e t is important to read all instructions carefully and make sure you have all the parts listed below before beginning pet door installation Installation Instructions Patent No 7784430 e Your pet door may be installed on the right or left side depending on which way your sliding door opens e There are several lock styles for vinyl sliding doors See page 6 to determine which lock you have e f you need help with any part of the installation call one of our associates Toll Free at 800 378 4385 M F 9 am to 4 pm PST and they will be happy to help you free of charge Tools Required For Installation Parts List 1 m As with any home improvement project if you do not have the tools or skills to properly install your pet door we suggest using a professional handyman or licensed contractor Hangers s a Spacers f Lock Catch 2 Hangers with 4 10 x 1 1 2 Screws and 6 Spacers POLY BAG 1 Parts color may be white ows Spacers 9 Lock Catches with 4 10 x 1 Self Drilling YRA Screws and 4 Spacers POLY BAG 9 74 Parts color may be white 1 Top H Section and 2 10 x 5 8 Self Drilling Screws POLY BAG 3 4 1 Door Seal Extension and 8 10 x 1 Self Drilling Screws PO2. LY BAG 4 i 7 2 Door Seal b w Extrusions 2 DrafteSeal Flat Pleces Darts color may be white 1 Lock Button Override see page 6 POLY BAG 9 Parts color may be white Installing Your White Vinyl Patio Pet Door Step 1 Installing the Pet Panel Door Hangers Remove existing Lock Catch plate as it may interfere with your new Vinyl Patio Pet Door Panel see Picture 1 If your catch plate is 1 wide or less you can reinstall into the Vinyl Patio Pet Door Poly Bag 1 contains 2 Hangers and 4 Screws 10 x 1 1 2 long Locate position of hangers see Sketch A Mark 2 lines inside door frame the lower at 5 and the upper at 84 1 2 for Tall Door or 69 for Standard Door from bottom of track i Place bottom edge of lower hanger on the 5 marked line and the upper ein ee setch A Mark location of hanger screw holes with pencil and drill 1 8 dia hole _91 8 16 oe approx 1 1 2 deep Tall Door Tall Door 75 3 4 69 Place hangers in track and Install Standard Standard using 10 x 1 1 2 screws Door Door see Picture 2 Important Do Not Overtighten 4 1 2 Tall Door 69 Standard Door Lift and locate Pet Panel in place see Picture 3 Continue to Page 3 Page 2 Installing Your White Vinyl Patio Pet Door continued Step 2 Measuring the H Section Gap 5 16 Insert t
3. ength from the top outer edge track see Picture 8 Place cut Door Seal to the bottom Extension against door outer edge ofthe panel Extension rests on door frame outer edge of door frame see Picture 9 top and bottom ammer me lightly to install ___ Extension Using a hacksaw cut Door Seal Extension to length Note Extension see picture 11 Use this measure Insert the 8 10 x 1 ment to mark the Self Drilling Screws into length on the Door the 8 pre drilled holes Seal Extension and tighten securely see Picture 10 see Picture 12 Continue to Page 5 Continuing the Installation Step 5 Secure the Top H Section Complete by installing 2 10 x 5 8 Self Drilling Screws through the Top H Section into the Vinyl Pet Door Panel on the inside of door see Picture 13 Continue to Page 6 Continuing the Installation Step 6 Installing the Lock Catch Our instructions will cover the majority of sliding door locks If your door lock is not compatible with the enclosed lock components you can use an alternate method of securing your door Please call us Toll Free at 800 378 4385 for more information if then place lo ok One Lock looks Catch and o0 Spacer like like this this Front Side View View Adjustment Screw Single Hook Style Door Lock if peach our peed lock Two Lock inal Catches k and like Spacers
4. k repeat steps for second hook Step 8 Install Door Seal Extrusions To properly measure the Door Seal Extrusions for installation close your sliding glass door against the pet door and measure length from the top of slider to the bottom sill of the door frame see Picture 20 Repeat this step for other side After measuring length use a hacksaw to cut Door Seal Extrusions to length see picture 21 then working from the bottom up press firmly and verify Seal Extrusions are snapped into grooves see Picture 99 Repeat these steps for other side NOTE In the event you are unable to close slider against the pet door the Extrusions inside soft vinyl gaskets may be removed see Picture 93 Continue to Page 8 to finish installation Finishing the Installation Step 9 Attaching the DrafteSeal and Optional Sliding Door Adjustments The DrafteSeal combined in 2 pieces attaches to the moving section of your sliding glass door To install the DrafteSeal measure the vertical distance or height of exposed glass between top and bottom frames of the sliding door and using this length cut DrafteSeal to size with scissors First clean the surface of frame with household glass cleaner then starting at top attach DrafteSeal by aligning edge so that It rubs lightly against glass see Picture 24 Pull paper off tape and gently press in place while working slowly down the DrafteSeal Do not pres
5. op H section on top of pet door panel see Picture 4 until it Is flush to frame see Picture 5 Slide H Section to edge of door frame Key not slide into channel p ae SS NOTE H Section must be flush with outer frame Measure the distance from the edge of pet door panel to edge of H section see Picture 6 This distance should be 5 16 If it is less than 5 16 you need to determine how many spacers will be needed to Install between the hangers and the inside of the sliding patio door frame to correct the distance see Sketch B 5 16 Minimum Sketch B Note You have been S Hanger provided with 6 spacers u of two thicknesses 2 10 x 1 1 2 There are O Screws A 4 each at 1 16 and t 2 each at 1 4 Spacers Continue to Page 4 Continuing the Installation Step 3 Install the Top H Section Slide Top H Section over top of springs until it is flush to frame Slide H Section to edge of door frame u making sure Do not slide into channel lt M that it is 5 16 i minimum from the side of door to edge of H Section see Picture 7 and inset 5 16 Minimum Your pet door includes one Door Seal Extension and two Door Seal Extrusions which mount on the side of the Vinyl Pet Door Panel To properly measure the Door Seal Extension for installation measure l
6. s too firmly in the event that repositioning is necessary Be sure that vinyl rubs lightly against glass all the way down length of glass Press DrafteSeal firmly in place along entire length when you are satisfied it is correctly placed We recommend caulking around entire pet panel inside and outside to insure the best possible weather seal NOTE If the sliding door portion of your vinyl patio door is not plumb with the Vinyl Pet Door Panel you may need to adjust the bottom rollers on the sliding vinyl patio door Please refer to the manufacturers adjustment instructions for your specific vinyl sliding patio door style Part 909 1042 Rev U 212
7. this like this i Double Hook Reverse Style Door Lock Adjustment Screws Front Side View View Adjustment Screw NOTE Most sliding doors have an adjustable locking mechanism see Picture 14 To Increase or decrease the locking strength of your door turn Adjustment Screw in or out if then place lock Two Lock looks Catches and like Spacers this like this Doue Adjustment Hook Style ENEWS Door Lock Front Side View View If your sliding door lock has a small button below the latch hook YOu will need to install the Lock Button Override Peel paper off the two sided tape Position pin to depress the lock button and press firmly in place see Picture 15 Continue to Page 7 Continuing the Installation Step 7 Installing the Lock Catch continued Place Lock Catch onto your existing door lock hook in the up locked position see Picture 16 Partially close your sliding door so that you can mark the location of the top edge of Lock Catch inside your pet door frame see Picture 17 Open door relocate Lock Catch to line up with pencil and mark holes see Picture 18 Install Lock Catch through 1 9 vinyl into reinforced plate using 10 x 1 Self Drilling Screws provided in Poly Bag 2 see Picture 19 Use Spacer if needed Lock Catch has slotted holes for adjustment if necessary If your sliding door has double hook Style loc
Download Pdf Manuals
Related Search