JELD-WEN Sierra LE 6068LPDP RH Instructions / Assembly
Contents
1. e The exterior face of the rough opening must be in a single plane E with less than 1 8 twist from corner to corner e Minimum double studs should be used at all rough openings be 3 4 smaller e The header must be supported by trimmer studs Verify the rough opening is square The A and B measurements should be the same Maximum allowable deviation from square is 1 4 E PREPARE SILL PAN 1 Cut a piece of sheet material to the 6 For continuous slab cut across the E a Fold sides and back up length shown pedi of rough opening sill plus o folding line r S 2 Lightly crease 7 Fold the three back a nada PE K 11 2 x folding lines 1 2 in sides up to make a from the two short dh 3 sided box and sides and one long 9 16 for step down ide landings fold the as Folding Line mas andinigs a front flap down Fold corner Fold front forward flap down 3 Measure the distance from the nailing fin to the interior edge of the frame and add 9 16 4 Take this distance from the back edge Continuous slab and lightly crease a Measure folding line across width the sheet material 5 For step down landings cut 1 2 in at this line on both sides of the sheet material 3 RELIABILITY for real life pa ae Step down JELD WEN INSTALLATION INSTRUCTIONS WINDOWS amp DOORS for Vinyl Patio Doors with Integral Nailing Fin JI1006 4 PREPARE R OPENIN2. 6 FLASH PATIO DOOR SPRAY ADHESIVE PRIMER foe PREPARE FLASHING 1 Cut pieces of JELD WEN self adhesive flashing to length as follows INSTALLATION INSTRUCTIONS for Vinyl Patio Doors with Integral Nailing Fin JI1006 Strike e One header piece 14 longer than the header e Two side pieces for continuous slab landings 5 longer than the sides or for step down landings 5 the height of the step e For step down landings only one sill piece 10 longer than the sill and 1 narrower than the height of the step SECURE PATIO DOOR Note Fastener heads must be flush Do not dent nailing fin Always use pre punched holes or pre drill with a 3 16 bit Builders Doors Only 9a Fasten patio door through nailing fin holes 4 from the corners and 12 apart all the way around the patio door Premium Doors Only 9b Fasten through nailing fin holes with 8 x 1 truss head screws At the head screws should be driven 4 from the corners and 4 apart For step down landings secure the sill in the same manner as the head Fasten the side jambs at 8 intervals Builders Patio Door 2 Apply spray adhesive per manufacturer s instructions protect door from overspray to nailing fin sheathing and building wrap around the patio door as shown RELIABILITY for real life pa A JELD WEN INSTALLATION INSTRUCTIONS WINDO
3. pan with sealant 10 For step down landings only cut plastic drain screen and apply over the to length of sill pan as shown sill 2 and staple The bottom of the 1 2 below sill edge The drain screen provides a path for air to dry any incidental moisture in the rough opening sill pan should be completely covered by the self adhesive flashing 4 RELIABILITY for real life pa A JELD WEN WINDOWS amp DOORS Ea INSTALL PATIO DOOR Warning To avoid injury use at least two people to install 1 For continuous slab landings only remove nailing fin at sill 2 Apply a 3 8 continuous bead of sealant across the sill pan back dam 3 Tilt patio door into the rough opening Make sure the back of the door makes solid contact with the sealant Adequately support the door until fully installed 4 Fasten patio door with a galvanized roofing nail between 3 and 4 from one lower corner SHIM THE JAMBS Note Secure all shims with sealant 5 From the interior shim the operating panel side jamb 6 from the corners and at the strike plate Align shims so that strike plate screws installed later will each penetrate a shim 6 Shim the stationary panel side jamb 6 from the corners and at center Shim the head N jamb 6 from the corners of each panel Inspect the patio door for square level and plumb Test for proper operation remove and reinstall if necessary
4. patio door to the ul AFTERINSTALLATION OC s SsSFT INSTALLATION Install exterior wall surface within seven days of patio door installation Seal any gaps or openings at end of horizontal mull joints with sealant Maintain gap of 1 4 3 8 between door frame and final exterior wall surface siding stucco etc Seal this gap on the sides with backer rod and sealant For step down landings also seal under the patio door sill Do not apply sealant on top of the drip cap On the interior insulate the void between the rough opening and the door frame with backer rod and sealant or low expansion foam Protect recently installed units from damage from plaster paint etc by covering the unit with plastic structure Pre installed screw Replacement screw Please visit jeld wen com resources for warranty and care and maintenance information Thank you for choosing JELD WEN WINDOWS amp DOORS 2007 JELD WEN inc JELD WEN and Reliability for Real Life are trademarks or registered trademarks of JELD WEN inc Oregon USA 08 07 8 RELIABILITY for real life pa A
5. G FOR RETROFIT INSTALLATIONS 7 Cut two pieces of JELD WEN self adhesive flashing 6 wide and the sill pan width 3 long Self Sealing Corner Flash After removing the old patio door remove sufficient siding to expose at least 9 of intact building wrap If damaged apply new building wrap in a shiplap manner Verify trimmer studs and header are structurally sound Continue with the instructions PREPARE BUILDING WRAP a For continuous 1 Trim building wrap slab landings lt a flush with the only cut out the rae edges of the rough inside corner continuous opening Verify slab only this does not void manufacturer s warranty 2 At the head slit building wrap 6 at 45 Tape up as shown Discard for l continuous slab only PREPARE SILL CONTINUOUS SLAB ONLY 3 Mark a line in the rough opening across the front and back of the sill pan as shown Remove sill pan and apply three beads of sealant between the marked lines b Adhere the pieces of flashing to the inside corners 8 Smooth gaps or bubbles beneath self adhesive flashing with a 4 Place the sill pan in J roller remove the rough opening and replace if 5 Apply spray necessary adhesive primer to the sill area Follow manufacturer s instructions for application methods 6 Cut a piece of JELD WEN self adhesive flashing the length of the sill INSTALL SILL PAN 9 Seal back corners of sill
6. JELD WEN WINDOWS amp DOORS INSTALLATION INSTRUCTIONS for Vinyl Patio Doors with Integral Nailing Fin JII006 ital IMPORTANT INFORMATION amp GLOSSARY Please Note Any patio door installation such that the sill is higher than 35 feet above ground level or into a wall condition not specifically addressed in these instructions must be designed by an architect or structural engineer Failure to install square level and plumb and on a flat surface without peak and valleys could result in denial of warranty claims for operational or performance problems Note to Installer Provide a copy of these instructions to the building owner By installing this product you acknowledge the terms and conditions of the limited warranty as part of the terms of the sale GLOSSARY Backer Rod backing material A material e g foam rod placed into a joint primarily to control the depth of the sealant Mulled Unit Two or more door units structurally joined together Pilot Hole A drilled hole that is no larger than the body of the screw minus the threads Shiplap The layering method in which each layer overlaps the layer below it so that water runs down the outside Weep Hole weep channel The visible exit or entry part of a water drainage system used to drain water out of a door eS ROUGH OPENINGS This installation guide specifically addresses sheathed wall and open stud construction FULLY SHEATHED WALL CONSTRUC
7. Patio Door 4 On the interior seal the lower 6 of gap between the rough opening and door jamb with backer rod and sealant on both sides of the patio door 5 Ensure sealant on back dam of the sill pan fully seals to the inside face of the sill Apply more sealant as necessary 6 RELIABILITY for real life pa A JELD WEN WINDOWS amp DOORS PATIO DOOR ADJUSTMENT Roller Adjustment Note Adjusting door too high may allow water and air leakage Adjust rollers just high enough to clear sill track 1 Builders doors have an adjustment screw on each lower end of the operating panel s Premium doors have access holes on the face of each lower end of the operating panel s Remove small vinyl plugs from each hole if present 2 Open operating panel enough to compare with frame jamb INSTALLATION INSTRUCTIONS for Vinyl Patio Doors with Integral Nailing Fin JI1006 Note Builders roller adjustment screws are in close proximity to the attachment screw Adjust only the lower screw as shown loosening the attachment screw will detach the roller from the operating panel 3 Using a 2 Philips head screwdriver turn the adjustment screw clockwise to raise the panel and counterclockwise to lower the panel 4 Adjust as needed until interlocks grid patterns and jambs line up 5 Test the ope
8. TION The wall framing is covered by sheathing and the door will be mounted with the nailing fin flush against the sheathing Sheathed Wall Thank you for selecting JELD WEN products Attached are JELD WEN s recommended installation instructions for Vinyl Patio Doors with nailing fin Any local building code requirements supersede the recommended installation instructions Read these instructions thoroughly before beginning They are designed to work in most existing applications however existing conditions may require changes to these instructions If changes are needed they are made at the installer s risk For installations other than indicated in these instructions contact a building professional Newer construction methods have led to an increase in air and water tightness in buildings This frequently leads to negative air pressure inside the home which can draw water through very small openings Our installation method seals the patio door to the weather barrier typically building wrap and uses a sill pan to capture and drain incidental storm water from under the patio door First Time 1 hr Experienced 3 4 hr Professional Y2 hr X Step Down Landing Estimated Install Time for New Construction LANDINGS These instructions cover two patio door sill conditions the step down landing and the continuous slab landing The installation methods vary sligh
9. WS amp DOORS for Vinyl Patio Doors with Integral Nailing Fin JI1006 6 FLASH PATIO DOOR CONTINUED APPLY THE SELF ADHESIVE FLASHING 6 Press the flashing down with a J roller 7 Do not allow gaps or bubbles beneath self adhesive flashing remove and replace if necessary Note Keep the edge of the JELD WEN self adhesive flashing as close to the patio door frame as possible 3 If applicable center and apply the sill piece underneath the sill bottom 1 2 of the drain screen must remain visible 4 Apply the side pieces starting 5 above the header 5 Center and apply the header piece above the header 7 COMPLETE INSTALLATION 1 Seal the upper corners of the patio door with a 1 4 bead of sealant Tool into a fillet shape 2 Release the building wrap from above the header previously taped up and overlap the header flashing Seal the ends with self adhesive flashing or building wrap tape 3 For continuous slab landings apply a 1 4 bead of sealant around the sill where it meets the slab Leave gaps at the weep holes as shown SUPPORT TRIM STEP DOWN LANDING ONLY On the exterior install support trim underneath the sill where it extends past the landing Position trim snugly against the bottom of the sill toe INSTALL BUMPER BUILDERS ONLY Install the bumper in the stationary panel side jamb at vertical center using the 1 self tapping screw provided Builders
10. king gun e Utility knife e Drill e Level 4 ft minimum e Construction stapler recommended RELIABILITY for real life pa A INSTALLATION INSTRUCTIONS JELD WEN for Vinyl Patio Doors with Integral Nailing Fin JI1006 WINDOWS amp DOORS EH REMOVE PACKAGING amp INSPECT YOUR PATIO DOOR e Splits cracks holes missing sections or other damage to the nailing fin longer than 6 and or within 1 2 of patio door frame REMOVE PACKAGING Remove shipping materials such as corner covers shipping blocks f or pads e For side by side mulled units a drip cap that extends the length of the frame plus 1 8 overhang on each end is required INSPECT YOUR PATIO DOOR If any of the above conditions represent a concern or if you expect environmental conditions to exceed the patio door s performance rating do not install the patio door Contact your dealer or distributor for recommendations e Cosmetic damage e Product squareness diagonal measurements must be within 1 4 difference e Correct product size color grid pattern handing glazing energy efficiency requirements etc PH INSPECT ROUGH OPENING e Verify the width and height of the patio door are each 1 2 3 4 smaller than e Verify the rough opening is level and plumb C The maximum allowable deviation is 1 8 e The rough opening sill must not be crowned or sagged D the rough opening width height Mulled units should
11. rating panel for proper operation 6 Re apply the small vinyl caps over the roller adjustment screw holes if applicable Raise panel Lower panel Attachment screw Adjustment screw COMPLETE INSTALLATION CONTINUED Lock Adjustment Note If the strike plate was not previously installed line up the screw holes with the dimples in the operating panel side jamb and drive screws through the two slotted screw holes If the lock does not properly engage the strike plate e Loosen the strike plate screws and move up or down until the latch engages properly If the door does not lock or is loose when locked e Turn the latch adjustment screw s in 1 2 turn increments clockwise to loosen or counterclockwise to tighten Premium doors have a double latch and two adjustment screws Lock hook adjustment screw Lock hook adjustment screw Lock hook adjustment screw RELIABILITY for real life pa A JELD WEN WINDOWS amp DOORS A COMPLETE INSTALLATION CONTINUED INSTALLATION INSTRUCTIONS for Vinyl Patio Doors with Integral Nailing Fin JI1006 FINISH INSTALLATION 1 Drive two 10 x 3 screws through the open screw holes in the strike plate included in hardware pack 2 Remove the pre installed screws from the strike plate and replace them with the remaining 10 x 3 screws from the Replacement screw hardware pack This will secure the
12. tly between landing types Continuous Sla Landing OPEN STUD CONSTRUCTION The wall framing needs to be covered by backing support before the patio door can be installed The door will be mounted with the nailing fin flush against the applied backing support This backing support should be a non water degradable thin max 1 8 thick sheet material such as vinyl sheeting Completely surround the rough opening with the backing support as shown Backing support must be applied before building wrap RELIABILITY for real life pa A Open Stud with Backing JELD WEN WINDOWS amp DOORS zl SAFETY amp HANDLING SAFETY e Read and fully understand ALL manufacturers instructions before beginning e Do not work alone Two or more people are required Use safe lifting techniques e Use caution when handling glass Broken or cracked glass can cause serious injury e Wear protective gear e g safety glasses gloves ear protection etc e Operate hand power tools safely and follow manufacturer s operating instructions e Use caution when working at elevated heights A NEEDED MATERIALS amp TOOLS MATERIALS e 1 3 4 galvanized roofing nails nails must penetrate at least 1 into framing e 8 x 1 stainless truss head screws for Premium doors only e Non compressible shims e JELD WEN 6 wide self adhesive flashing part 08987 or equivalent 9 if required by local code e Protec
13. to Wrap Safseal Systems 5500 spray adhesive primer or as recommended by the self adhesive flashing manufacturer e Sealant polyurethane if painted 100 silicone if left exposed and backer rod e Plastic drain screen with crisscross or woven pattern sold in 6 widths to protect rain gutters for step down landings INSTALLATION INSTRUCTIONS for Vinyl Patio Doors with Integral Nailing Fin JI1006 MATERIALS AND PATIO DOOR HANDLING e Make sure the operating panel is secured prior to installation e Heed material manufacturers handling and application instructions e Protect adhesive surfaces from dirt moisture direct sunlight and folding over onto themselves e Handle in vertical position do not drag on floor e Do not put stress on joints corners or frames e Store patio door in dry well ventilated area in vertical leaning position to allow air circulation do not stack horizontally e Protect from exposure to direct sunlight during storage e Install only into vertical walls and when conditions and sheathing are dry e Never use solvent based sealants on vinyl products IF INJURY OCCURS IMMEDIATELY SEEK MEDICAL ATTENTION e Sheet metal flashing or bendable vinyl sheeting for sill pan 4 wide for 2 x 4 wall e 3 8 staples for step down landings Note Follow all material manufacturers instructions for proper use and compatibility TOOLS e Cutting shears sill pan e J roller e Tape measure e Caul
Download Pdf Manuals
Related Search