Zenoah CHT2310 User's Manual
Contents
1. It will cause severe damage to the internal engine parts very quickly 2 GASOHOL It can cause deterioration of rubber and or plastic parts and disruption of engine lubrication 3 OIL FOR 4 CYCLE ENGINE USE It can cause spark plug fouling exhaust port blocking or piston ring sticking 4 Mixed fuels which have been left unused for a period of one month or more may clog the carbu retor and result in the engine failing to operate prop erly 5 In the case of storing the product for a long period of time clean the fuel tank after rendering it empty Next activate the engine and empty the carburetor of the composite fuel 6 In the case of scrapping the used mixed oil con tainer scrap it only at an authorized repository site ay e As for details of quality assurance read the descrip tion in the section Limited Warranty carefully More over normal wear and change in product with no functional influence are not covered by the warranty Also be careful that if the usage in the instruction manual is not observed as to the mixed gasoline etc described therein it may not be covered by the warranty GB 9 HT2310 CHT2310 7 Operation STARTING ENGINE A WARNING The cutting head will start moving upon the engine starts 1 Release the throttle lever and make sure it is fully back 2 Set the ignition switch to the I position paneeaed CHT2310 a Throttle lever b Ignition switch 3 P2. We won t warrant the machine if you use the remodeled hedge trimmer or if you don t ob serve the proper usage written in the manual Warning Attention Keep all children bystanders and helpers 15 meters away from the machine 4 Symbols on the machine For safe operation and maintenance symbols are carved in relief on the machine According to these indications please be careful not to make a mistake oih NI The direction to close the choke Position AIR CLEANER COVER The port to refuel the MIX GASOLINE Position FUEL TANK CAP L The direction to open the choke Position AIR CLEANER COVER GB 5 HT2310 CHT2310 A 5 For safe operation THIS MACHINE CAN CAUSE GB 6 SERIOUS INJURIES Read this manual carefully until you com pletely understand and follow all safety and operating instruc tions Also know how to stop the machine quickly in an emer gency Keep this manual handy so that you may refer to it later when ever any questions arise Also note if you have any questions which cannot be answered herein contact the dealer from whom you purchased the prod uct Always be sure to include this manual when selling lending or otherwise transferring the own ership of this product Never allow children or anyone unable to fully understand the directions given in the manual to use the machine WORKING CONDITION 1 When using the product you s
3. SOMEONE COMES Guard against hazardous situa tions at all times Warn adults to keep pets and children away from the area Be careful if you are ap proached Injury may result from flying debris If someone calls out or otherwise interrupts you while working al ways be sure to turn off the en gine before turning around MAINTENANCE JE In order to maintain your product in proper working order perform the maintenance and checking operations described in the manual at regular intervals Always be sure to turn off the en gine before performing any main tenance checking procedures or working on the machine A WARNING The metallic parts reach high tem peratures immediately after stop ping the engine 3 When replacing the cutting at tachment or any other part or when replacing the oil or any lu bricant always be sure to use only ZENOAH products or products which have been cer tified by ZENOAH for use with the ZENOAH product Inthe event that any part must be replaced or any maintenance or repair work not described in this manual must be performed please contact a representative from the store nearest ZENOAH authorized servicing dealer for assistance Do not use any accessory or at tachment other than those bear ing the ZENOAH mark and rec ommended for the unit Refill after 6 Under no circumstances should you ever take apart the product or alter it in an
4. has been moved fully back turn off the engine and take the unit to your authorized ZENOAH servic ing dealer for repair USING THE PRODUCT IMPORTANT Cut only materials recommended by the manufacturer And use only for tasks explained in the manual 1 Grip the handles firmly with both hands using your whole hand Place your feet slightly apart slightly further apart than the width of your shoulders so that your weight is distributed evenly across both legs and always be sure to maintain a steady even posture while working 2 Keep cutting attachment below waist level 3 Maintain the speed of the engine at the level required to perform cutting work and never raise the speed of the engine above the level necessary 4 If the unit starts to shake or vi brate turn off the engine and check the whole unit Do not use it until the trouble has been prop erly corrected 5 Keep all parts of your body away from moving cutting attachment and hot surfaces 6 Never touch the muffler soark plug or other metallic parts of the engine while the engine is in op eration or immediately after shut ting down the engine Doing so could result in serious burns or electrical shock GB 7 H12310 CHT2310 A 5 For safe operation ra ae A Ozenonn A dr GB 8 i While operating the machine be always sure of a safe and secure operating position especially when using steps or a ladder IF
5. 2 Engine starts but does not keep running hard re starting CHECK PROBABLE CAUSES ACTION fuel tank incorrect fuel or staled fuel drain it and use correct fuel carburetor adjustment screw out of normal range adjust to normal range muffler cylinder exhaust port carbon is built up wipe away air cleaner clogged with dust wash cylinder fin fan cover clogged with dust clean When your unit seems to need further service please consult with our ZENOAH service shop in your area Limited warranty Should any failure occur on the product under normal operating conditions within the applicable warranty pe riod the failed part will be replaced or repaired free of charge by a ZENOAH authorized dealer WARRANTY PERIOD 1 year 6 months if used profes sionally and 30 days if used for rental purpose from the date of initial purchase THE PURCHASER SHALL BEAR COSTS OF TRANS PORTING THE UNIT TO AND FROM THE ZENOAH DEALER THE PURCHASER SHALL NOT BE CHARGED FOR DI AGNOSTIC LABOR WHICH LEADS TO THE DETERMI NATION THAT A WARRANTED PART IS DEFECTIVE IF THE DIAGNOSTIC WORK IS PERFORMED AT THE ZENOAH DEALER THE PURCHASER OR OWNER IS RESPONSIBLE FOR THE PERFORMANCE OF THE REQUIRED MAINTE NANCE AS DEFINED BY THE MANUFACTURER IN THE OWNER OPERATOR MANUAL ANY WARRANTED PART WHICH IS NOT SCHEDULED FOR REPLACEMENT AS REQUIRED MAINTENANCE OR WHICH IS SCHEDULED ONLY FOR REGULAR IN SPECTION TO THE EFFECT O
6. 848D0593A0 706 zenon a CN OWNER S MANUAL HEDGE TRIMMER H I 2 3 T 0 A WARNING A C Before using our products H l 3 1 0 please read this manual carefully to understand the proper use of your unit HT2310 CHT2310 EXPLANATION OF SYMBOLS AND SAFETY WARNINGS HT2310 WARNING PA RISK OF DAMAGING HEARING 08 Wear head eye and ear protection CHT2310 WARNING i RISK OF DAMAGING HEARING 1 06 Wear head eye and ear protection MODEL SOUND LEVEL VIBRATION LEVEL ISO 11094 prEN774 ISO 8662 L guaranteed L cay Ag A 8 HTZ2310 108 dB A 97 dB A 6 5 m s CHTZ2310 106 dB A 95 dB A 12 3 m s 8 1 m s APPROVAL NUMBER OF CE EXHAUST EMISSION REGULATION e 13 97 68SH2G3 2002 88 0104 04 GB 2 H12310 CHT2310 EC DECLARATION OF CONFORMITY We ZENOAH CO LTD 1 9 Minamidai Kawagoe Saitama Japan declare in sole responsibility that the following products referred to in this declaration conform with DIRECTIVE 89 336 EEC 98 37 EC 2000 14 EC Internal control production The products referred to are DESIGNATION HEDGE TRIMMER MODELS HT2310 CHT2310 SERIAL NUMBERS 70300001 and up The company named above will keep on file the following technical docu mentation for any inspection purpose e Operation instructions e Plans and Drawings e Description of measures designed to ensure conformity e Other technical documentation Specification sheet Ins
7. F REPAIR OR REPLACE AS NECESSARY SHALL BE WARRANTED FOR THE WARRANTY PERIOD ANY WARRANTED PART WHICH IS SCHEDULED FOR REPLACEMENT AS REQUIRED MAINTENANCE SHALL BE WARRANTED FOR THE PE RIOD OF TIME UP TO THE FIRST SCHEDULED REPLACEMENT POINT FOR THE PART ANY REPLACEMENT PART THAT IS EQUIVALENT IN PERFORMANCE AND DURABILITY MAY BE USED IN NON WARRANTY MAINTENANCE OR REPAIRS AND SHALL NOT REDUCE THE WARRANTY OBLIGATION OF THE COMPANY THE COMPANY IS LIABLE FOR DAMAGES TO OTHER ENGINE COMPONENTS CAUSED BY THE FAILURE OF A WARRANTED PART STILL UNDER WARRANTY THE WARRANTY DOES NOT APPLY TO THOSE UNITS WHICH HAVE BEEN DAMAGED BY NEGLIGENCE OF INSTRUCTION LISTED IN THE OWNER OPERATOR MANUAL FOR PROPER USE AND MAINTENANCE OF THE UNITS ACCIDENT MISHANDLING ALTERATION ABUSE IMPROPER LUBRICATION USE OF ANY PARTS OR ACCESSORIES OTHER THAN THOSE SPECIFIED BY THE COMPANY OR OTHER CAUSES BEYOND THE COMPANY S CONTROL THIS WARRANTY DOES NOT COVER THOSE PARTS REPLACED BY NORMAL WEAR OR HARMLESS CHANGES IN THEIR APPEARANCE THERE ARE NO OTHER EXPRESS WARRANTIES IMPLIED WARRANTIES INCLUDING THOSE OF MER CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO TWO 2 YEARS OF HOME USE ONE 1 YEAR FOR ANY OTHER USE FROM THE ORIGINAL DELIVERY DATE LIABILITIES FOR INCIDENTAL OR CONSEQUENTIAL DAMAGE UNDER ANY AND ALL WARRANTIES ARE EXCLUDED IF YOU NEED TO OBTAIN MORE INFORMATION PLEASE CALL YOUR NEAREST SERVICE CE
8. NTER OR CHECK PLEASE ZENOAH WEB SITE htto www zenoah net GB 15
9. VERY 100 HOURS OF USE Remove the muffler insert a Screwdriver into the vent and wipe away any carbon buildup Wipe away any carbon buildup on the muffler exhaust vent and cylin der exhaust port at the same time Tighten all screws bolts and fittings Check to see if any oil or grease has worked its way in between the clutch lining and drum and if it has wipe it away using oil free lead free gasoline 9 Storage iN Oil the blade to prevent rust Empty the fuel tank and put the cap back on Remove the spark plug pour a small amount of oil into the cylinder Rotate the crankshaft several times using the start ing rope in order to distribute the oil Put the spark plug back in Wrap the engine with a plastic sheet store the trimmer in a dry place preferably not in direct contact with the floor and away from heat Sources 10 Disposal When disposing your machine fuel or oil for the machine be sure to allow your local regulations GB 14 HT2310 CHT2310 11 Troubleshooting guide Case 1 Starting failure CHECK PROBABLE CAUSES ACTION fuel tank incorrect fuel drain it and use correct fuel fuel filter fuel filter is clogged clean carburetor adjustment screw out of normal range adjust to normal range sparking no spark spark plug is fouled wet clean dry plug gap is incorrect correct GAP 0 6 0 7 mm spark plug disconnected retighten Case
10. When anew machine is first operated in the first few e To reduce fatigue when trimming hedges the handle minutes grease may come out of the gear case But can be swivelled through 45 or 90 to the left or right since this is excess grease there is no cause for alarm Just wipe it off with the engine stopped for next use e Always remember that the TIP of the line does cut ting You will achieve better results by not crowding the line into the cutting area Allow the unit to trim at its Own pace e Do not press the throttle during this operation Proceed as follows 1 Free the handle by pulling the locking lever 2 Turn the handle until the locking lever clicks into place 3 When the handle is locked in its new position you can apply the throttle again 1 locking lever e You can swivel the handle even with the engine idling because the hedge trimmer is equipped with a blade brake that maintains the blades ata standstill GB 11 HT2310 CHT2310 8 Maintenance Every Every Every Before 25 Procedure fuel leaks fuel spillage fuel tank air filter fuel filter inspect clean idle adjusting screw see adjusting idling speed system components ep QD 32 O C 09 2 O C 09 Dy O C 09 ee Py fo fo replace if necessary ae replace carburetor if necessary spark plug clean and readjust V GAP 0 6 0 7 mm plug gap replace if necessary cylind
11. d medicine or at any other time when a pos sibility exists that your judgment might be impaired or that you might not be able to operate the product properly and in a safe manner When planning your work sched ule allow plenty of time to rest Limit the amount of time over which the product Is to be used continuously to somewhere around 30 40 minutes per ses sion and take 10 20 minutes of rest between work sessions Also try to keep the total amount of work performed in a single day under 2 hours or less A WARNING 1 If you don t observe the working time or working manner See USING THE PRODUCT Re petitive Stress Injury RSI could occur If you feel discomfort redness and swelling of your fingers or any other part of your body see a doc tor before getting worse To avoid noise complaints in gen eral operate product between 8 a m and 5 p m on weekdays and 9 a m to 5 p m on weekends A 5 For safe operation Check and follow the local regula tions as to sound level and hours of operations for the product BEFORE STARTING THE ENGINE 1 The area within a perimeter of 15 m of the person using the product should be considered a hazardous area into which no one should enter If necessary yellow warning rope warning signs should be placed around the pe rimeter of the area When work is to be performed simultaneously by two or more persons care should also be taken
12. el E FUEL A WARNING e Gasoline is very flammable Avoid smoking or bringing any flame or sparks near fuel Make sure to stop the engine and allow it cool before refuel ing the unit Select outdoor bare ground for fuel ing and move at least 3 m 10 ft away from the fueling point before starting the engine r The Zenoah engines are lubricated by oil specially formulated for air cooled 2 cycle gasoline engine use If Zenoah oil is not available use an anti oxidant added quality oil expressly labeled for air cooled 2 cycle engine use JASO FC GRADE OIL or ISO EGC GRADE Do not use BIA or TCW 2 stroke water cooling type mixed oil E RECOMMENDED MIXING RATIO GASOLINE 50 OIL 1 when using ZENOAH genuine oil e Exhaust emission are controlled by the funda mental engine parameters and components eq carburation ignition timing and port timing with out addition of any major hardware or the intro duction of an inert material during combustion e These engines are certified to operate on unleaded gasoline e Make sure to use gasoline with a minimum octane number of 89RON USA Canada 87AL e f you use a gasoline of a lower octane value than prescribed there is a danger that the engine tem perature may rise and an engine problem such as piston seizing may consequently occur Unleaded gasoline is recommended to reduce the contamination of the air for the sake of your health and the environment Poor qualit
13. er fins intake air cooling vent O ae muffler spark arrester cylinder exhaust port throttle lever ignition switch check operation cutting parts replace if something s wrong screws nuts bolts tighten replace debris guard make sure to attach Y SAFETY LOCK A WARNING e Make sure that the engine has stopped and is cool before performing any service to the machine Con tact with moving cutting head or hot muffler may result in a personal injury BLADE Check the blade and the fasteners for looseness cracking or bending Check the cutting edges and reform with a flat file Point 1 Keep the end corner sharp 2 Round the root of the edge 3 Do not use water when using a grinder GB 12 Stop operation when the safety lock is de fective Safety lock is the device not to accelerate the throttle lever without intention While pushing the safety lock you can accelerate the throttle lever 1 Safety lock Check if the throttle lever does not move when you do not push the safety lock Check if the throttle lever moves when you grasp or release it while pushing the safety lock Check if the safety lock returns to its original position when you release your hand from safety lock If you find any defects at the checks above contact your nearest servicing dealer for repair HT2310 CHT2310 8 Maintenance AIR FILTER SPARK PLUG e The air filter if clogged will
14. hould wear proper clothing and protective equipment 1 Helmet 2 Ear protectors 3 Protection goggles or face protector 4 Thick work gloves 5 Non slip sole work boots And you should carry with you 1 Attached tools 2 Properly reserved fuel 3 Spare blade 4 Things to notify your working area rope warning signs 5 Whistle for collaboration or emergency 6 Hatchet or saw for removal of obstacles Do not wear loose clothing jew elry short trousers sandals or go barefoot Do not wear anything which might be caught by a mov ing part of the unit Secure hair so it is above shoulder length WORKING CIRCUMSTANCE 1 Never start the engine inside a closed room or building Exhaust gases contain dangerous carbon monoxide 2 Never use the product a when the ground is slippery or when you can t maintain a steady posture b Atnight at times of heavy fog or at any other times when your field of vision might be limited and it would be diffi Cult to gain a clear view of the working area c During rain storms during lightning storms at times of strong or gale force winds or at any other times when weather conditions might make it unsafe to use the product WORKING PLAN 1 You should never use the prod uct when under the influence of alcohol when suffering from ex haustion or lack of sleep when suffering from drowsiness as a re sult of having taken col
15. on switch Throttle Cable Muffler Blade Front handle Rear handle Plate receive Oe oe oe ee IS HT2310 2 Specification O E EEEN ence OE EEEE E E lawns HT2310 CHT2310 MF vaste as nse cect alee sna dete nities ales Aca woe nisl E SE EET E teed A double action type PR23107 CHATZ 10 ea e e Single blade Double blade Blade length from the tip of Gear Case Pe WO Tr e E EEE EE EET 750 600 mm Engine MOOO acdc e e e E e A e Zenoah G23LH PED EMON ae E A E R 22 5 Cm ONO ep E A E E Mazensnaae Diaphragm type OMO SYSTE cincina ea eia C controlled flywheel magneto DAK 6 6 6 ene anne eee ee eee em Champion RCU6Y or NGK BPMR7A FY careers ta eeuetea ceisler A pee Mixuture Gasoline 50 Oil 1 E TETE EET EE E E AEE when using ZENOAH genuine oil FUGAR A e a e a E 0 6L RUINS a E E E E E E E E Recoil starter AU ea E E N Centrifugal type Reduction ratio P A ol 209 TO a E ot Senn ee reer eer 4 14 4 14 Dry weight Eer 6S coll 0220 a 0 e eee nee ete ome een ee eee eee eae 9 3 0 0 kg specifications are subject to change without notice GB 4 H12310 CHT2310 3 Warning labels on the machine If warning label peels off or becomes soiled and impossible to read you should contact the dealer from which you purchased the product to order new labels and affix them in the required location s Read owner s manual before operat ing this machine Wear head eye and ear protection Never modify your machine
16. pection standard Saitama Japan 1st March 2007 Masahiko GOUDA General Manager Quality Assurance Department A SAFETY FIRST Contents Instructions contained in warnings within this manual marked with a A symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury and for this reason you are requested to read all such instructions le Fare Oe QUOI e sass ez eee 4 carefully and follow them without fail ae Px SOSCINCALONS ssc cevisdctwenctierieneninasndiect aeien 4 3 Warning labels on the machine 0006 5 WARNINGS IN THE MANUAL 4 Symbols on the machine ncis 5 A WARNING Di For safe operation crcnicerpicctsoncenaveirecnsisgnnsyeecees 6 This mark indicates instructions which must be followed in or ore ic e 9 der to prevent accidents which could lead to serious bodily in 7 Operation 10 jury or death OO eer 8 MAINTENANCE xs icivcssacdicrbexddasasetieeseriawiidosctdeiod 12 IMPORTANT O StOPAGS cacaiecesecsadssosndscedecanaszaddhennansneored esivetens 14 This mark indicates instructions which must be followed or it 10 Disposal 44 leads to mechanical failure breakdown or damage tia As ae ees 11 Troubleshooting guide ccceecesseeeeseeees 15 EE NOTE This mark indicates hints or directions useful in the use of the product GB 3 H12310 CHT2310 1 Parts location Right handle Fuel tank Starter Left handle Throttle lever Igniti
17. reduce the engine perfor e Starting failure and misfiring are often caused by a mance Check and clean the filter element in warm fouled spark plug Clean the spark plug and check soapy water as required Dry completely before in that the plug gap is in the correct range For a re stalling If the element is broken or shrunk replace placement plug use the correct type specified by with a new one ZENOAH 0 6 0 7 mm e REPLACEMENT PLUG IS A CHAMPION RCJ6Y or NGK BPMR7A IMPORTANT e Note that using any spark plug other than those des ignated may result in the engine failing to operate prop FUEL FILTER erly or in the engine becoming overheated and dam e When the engine runs short of fuel supply check the aged o fuel cap and the fuel filter for blockage e To install the spark plug first turn the plug until it is finger tight then tighten it a quarter turn more with a socket wrench TIGHTENING TORQUE 14 7 21 5 Nem GEAR CASE Supply multi purpose grease at every 25 hours of use WAY OF THE COOLING AIR 1 Use a grease pump This engine is air cooled Dust clogging between the 72 Feed grease until it comes out of the base of inlet port of the cooling air and cylinder fins will cause blades a overheating of the engine Periodically check and clean the cylinder fins after removing the air cleaner and the cylinder cover GB 13 H12310 CHT2310 8 Maintenance PROCEDURES TO BE PERFORMED AF TER E
18. to constantly look around or otherwise check for the presence and locations of other people working so as to maintain a distance between each person sufficient to ensure Safety 2 Check the condition of working area to avoid any accident by hit ting hidden obstacles such as stumps stones cans or broken glass IMPORTANT Remove any obstacle before begin ning work 3 Inspect the entire unit for loose fasteners and fuel leakage Make sure that the cutting attachment is properly installed and securely fastened STARTING THE ENGINE 1 Keep bystanders especially chil dren and animals at least 15 m away from the operating point If you are approached immediately stop the engine 2 The product is equipped with a centrifugal clutch mechanism so the cutting attachment begins to move as soon as the engine is started by putting the throttle into the start position When starting the engine place the product onto the ground in a flat clear area and hold it firmly in place so as to ensure that neither the cutting part nor the throttle come into contact with any obstacle when the engine starts HT2310 CHT2310 A WARNING Never place the throttle into the high speed position when starting the engine 3 After starting the engine check to make sure that the cutting at tachment stops moving when the throttle is moved fully back to Its original position If it continues to move even after the throttle
19. ush the primer pump several times until overflown fuel flows out in the clear tube 1 Primer pump 4 Move the choke lever to the closed position IS c t b a Choke lever b Open c Close GB 10 5 Place the unit on a flat firm place Keep the cutting head clear of everything around it 6 While holding the unit firmly pull out the starter rope quickly until engine fires HT2310 CHT2310 7 After the engine has started allow the engine to warm up Pull the throttle lever STOPPING ENGINE 1 Release the throttle lever and run the engine for half a minute 2 Shift the ignition switch to the STOP position HT2310 CHT2310 If the engine doesn t stop after stopping the switch close the choke so that engine will stop after a little HT2310 CHT2310 7 Operation CUTTING WORK Use only as much throttle as is needed to do the job Excessive engine speed is unnecessary A WARNING E Avoid cutting thick branches for which will damage e Weather conditions and altitude may effect the blades and shorten the life of drive systems carburation Tilting the trimmer 5 to 10 to the cutting object will e Do not allow anyone to stay close to the hedge make the job easy and bring a good result trimmer while working or while adjusting the car buretor Always keep your body to the carburetor side of your trimmer never on the muffler side HOW TO USE HANDLE CHT2310
20. y gasolines or oils may damage sealing rings fuel lines or fuel tank of the engine E HOW TO MIX FUEL A WARNING e Pay attention to agitation 1 Measure out the quantities of gasoline and oil to be mixed Put some of the gasoline into a clean approved fuel container Pour in all of the oil and agitate well Pour in the rest of gasoline and agitate again for at least one minute As some oils may be difficult to BO J9 HT2310 CHT2310 agitate depending on oil ingredients sufficient agi tation is necessary for the engine to last long Be careful that if the agitation is insufficient there is an increased danger of early piston seizing due to ab normally lean mixture 5 Puta clear indication on the outside of the container to avoid mixing up with gasoline or other contain ers 6 Indicate the contents on outside of container for easy identification E FUELING THE UNIT 1 Untwist and remove the fuel cap Rest the cap ona dusitless place 2 Put fuel into the fuel tank to 80 of the full capacity 3 Fasten the fuel cap securely and wipe up any fuel spillage around the unit A WARNING 1 Select bare ground for fueling 2 Move at least 10 feet 3 meters away from the fuel ing point before starting the engine 3 Stop the engine before refueling the unit At that time be sure to sufficiently agitate the mixed gasoline in the container E FOR YOUR ENGINE LIFE AVOID 1 FUEL WITH NO OIL RAW GASOLINE
21. y way Doing so might result in the product be coming damaged during opera tion or the product becoming un able to operate properly HANDLING FUEL 1 The engine of the ZENOAH proa uct is designed to run on a mixed fuel which contains highly flam mable gasoline Never store cans of fuel or refill the tank of the unit in any place where there is a boiler stove wood fire electrical sparks welding sparks or any other source of heat or fire which might ignite the fuel Never smoke while operating the unit or refilling its fuel tank When refilling the tank always turn off the engine and allow it to cool down Take a careful look around to make sure that there are no sparks or open flames any where nearby before refueling Wipe spilled fuel completely us ing a dry rag if any fuel spillage occurs during refueling After refueling screw the fuel cap back tightly onto the fuel tank and then carry the unit to a spot 3 m or more away from where it was refueled before turning on the engine Do not inhale fuel fumes as they are toxic TRANSPORTATION 1 When hand carrying the product cover over the cutting part If nec essary lift uo the product and carry it paying attention to the blade Never transport the product over rough roads over long distances by vehicle without removing all fuel from the fuel tank If doing so fuel might leak from the tank dur ing transport 6 Fu
Download Pdf Manuals
Related Search