Home

Zenith L20V54S User's Manual

1. fo VOLUME CONTROL TV ON OFF OPEN CHAN UP DATA IN Controlling the TV with Mechanical Switches COMMON AUDIO Our Pin 4 common is momentarily connected to pin 1 3 or CHAU DOWN 6 via push action switches to control On Off and Channel Up Down These pins are at 13 volts DC when measured from pin 4 with the switches open Current draw is 8 mA Purpose when a switch is closed This operation is identical to External TV On Off switch previous Zenith models using the 5 Wire Interface except Not used that only 7 volts DC was supplied and current draw was External Channel Up switch or Data in only 2 5 mA Common connection for control data and audio output Impedance to earth ground is a 10 meg resistor in parallel with a 1100 pf capacitor Isolated audio output Nominal 14 ohm source impedance with short circuit protection Intended for a pillow speaker with a low impedance pad type volume control External Channel Down switch PAGE 13 Power Cord Hookup Connect the AC power cord directly to the LCD TV Monitor AC Power Cord Hookup The LCD TV Monitor is designed to operate on 120V AC power Locate the AC Power Cord input socket on the back of the LCD TV Monitor Insert the AC power cord connector into the AC Socket on the TV as shown below VIDEO SPEAKER SWITCH HDMI lS RS 232C UPDATE RS 232C FUTURE PILLOW NORMAL IN SELECT USE
2. message displayed press 2 to go to the TEACH TO TV option press ON OFF POWER or ENTER Ferrite Core TDK ZCAT 2035 0930 QuickSet II Programmer LT2002 Clone Programmer CLONE SELECTION MENU 1 LEARN FROM TV Select the LT2002 memory that the new setup is in Press On Off to transfer the new setup and other information to the 2 TEACH TO TV 3 SET CLONE CLOCK FROM TV 4 SET TV CLOCK FROM CLONE 5 DISPLAY TV SETUP 6 DISPLAY CLONE SETUP TO CHANGE MENU ITEMS PRESS CHANNEL KEYS OR DIGITS TO EXECUTE ITEM PRESS ON OFF POWER OR ENTER This menu should appear after any key is pressed on the Installer remote r new L20V54S Teaching usually takes 2 3 minutes After the TEACHING COMPLETE message is displayed press any key to return to the Clone menu then press ON OFF POWER or ENTER If finished detach M P I cable from the target newly cloned L20V54S Disconnect L20V54S Power for 15 Seconds Unplug the AC power cord of the newly cloned L20V54S from the power outlet for about 15 seconds to activate the newly copied setup PAGE 44 TEACHING IN PROGRESS PLEASE WAIT Na This display will appear during Teaching function TEACHING COMPLETE This display will appear after Teaching is complete Installer Menu Use the Installer s Menu to set up or
3. IMPORTANT SAFETY INSTRUCTIONS Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong is provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus Only use attachments accessories specified by the manufacturer Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over ooN oNN KRWDY PB oO PORTABLE CART WARNING 13 Unplug this apparatus during lightning storms or when unused for long periods of time 14 Refer all servicing to qualified service personnel Servicing is requir
4. PAGE 47 Installer Menu Continued from previous page The value range is 0 to 63 with 63 as the default which gives the user the full range of volume control if item 008 MIN VOLUME is also set at 0 Change values with ADJ Left Right arrow keys It may be best to set the same value on every L20V54S Note The maximum volume level cannot have a value setting lower than the MIN VOLUME level described previously 010 MUTE DISABLE Enables or disables sound mute function If set to 1 sound cannot be muted mute is disabled If set to 0 sound can be muted 011 KEY DEFEAT Keyboard Defeat If set to 1 key defeat prevents the end user from accessing the on screen menus with the display front panel MENU SELECT and Left Right arrow keys and TV AV do not function If set to 0 those keys do function Note The menus can always be accessed by pressing MENU on the remote 012 IR BANKS EN IR Banks Enable For direct access to a particular Channel Bank When enabled installer can access a channel bank by inputting the IR code for the bank 013 SCAN MODE Allows variation in setting the On Off with Channel UP DOWN You may opt for TV channels only TV channels Off 0N TV channels FM radio TV channels FM radio Off On with these set tings for Scan Mode SCAN MODE Characteristics 0 Channel up down keys change channels only 1 Channel down below the lowest channel or channel up higher than the highe
5. Rear Aux Enable Set to 1 to enable display panel rear AUX Video 1 input Set to 0 to disable display panel rear AUX Video 1 input 046 STRT AUX SRCE Start Aux Source Sets the starting AUX source Start source if start channel 0 1 Video1 3 HDMI 1 255 Last Aux 047 AUX STATUS Set to 1 for M P I AUX source to be reported as a channel number instead of channel 0 Set to 0 to disable AUX identification change Controls M P I status channel response for AUX inputs 053 DIS CH TIME Disable Channel Time Set to 1 to disable the Channel Time display Channel Time display will not appear Set to 0 to enable the Channel Time display 069 EN CH T COL Enable Channel Time Custom Color Set to 1 to enable custom color for the Channel Time display Set to 0 to disable custom color for the Channel Time display 070 FOR CH TIME Channel Time Display Foreground Color Set according to Color Chart 0 Black 3 Yellow 1 Red 4 Blue 2 Green 5 Violet Note If foreground and background colors are the same menu background is transparent 6 Cyan 7 White 071 BCK CH TIME Channel Time Display Background Color Set according to Color Chart 0 Black 3 Yellow 1 Red 4 Blue 2 Green 5 Violet Note If foreground and background colors are the same menu background is transparent 6 Cyan 7 White 073 CH NOT AVBLE Channel Not Available If set to 1 and item 028 CHANNEL OVERRIDE is set
6. 7 Manual If the end user will have access to the Alarm it may be best to use the Manual Clock Set mode and set the clock to local time manually Mini glossary TIME A four digit figure broken down into hours and minutes used to enter the current time when setting the clock or wake up alarm HOURS First two digits that are entered when setting the clock or the wake up alarm MINUTES The last two digits that are entered when setting the clock or the wake up alarm PAGE 24 Clock Setup Continued Daylight Saving EL Installer can elect to use Daylight Savings to adjust the clock time ve This is operated from the Automatic Time Settings z p_ Menu Language S Menu Transparency Press the MENU button and then use the ADJ A V button to highlight the Setup men Press the OK Enter button to highlight Time Press the OK Enter button to highlight Clock Manual or Auto will appear on the menu next to clock Select Auto on the submenu with the Down arrow and press the OK Enter button Use the ADJ Up Down Left Right arrows to highlight and set the Daylight Savings options On Yes or Off No for your local area KY When finished press Menu repeatedly to remove the menus Time Zone Settings Installer can set the Time Zone Yr Vc Menu Transparency Transparent Press the MENU button and then use the ADJ A button ee to highlight the Setup menu Press the OK Enter button
7. Bed 2 switch on patient remote The position of the Bed 1 Bed 2 switch must correspond to the setting in the Installer s menu The switch above can be set by sliding it to the Bed 1 or Bed 2 position On the patient s remote the Bed 1 or Bed 2 position can be selected by using a paper clip or a ball point pen to slide the switch to the correct position Left position Bed 1 Right Position Bed 2 PAGE 19 Auto Program Channel Search Use Auto Program to automatically find and store all of the channels available in the selected Tuning Band Note Tuning Band must be set before doing the channel search See Installer menu item 003 Band AFC Default setting is 1 for CATV When Auto Program is run any assigned channel labels are automatically removed With the optional Installer remote control in hand press the POWER key to turn the TV on Press the MENU button and then use the ADJ A V button to select the Channel menu Press the OK Enter button With Auto Program highlighted press the OK Enter button Press the OK Enter button to start the channel search After finding all available channels a display appears briefly showing the number of analog and digital channels found Press the MENU button to remove the menus Auto Program finds channels being received by the TV s analog and digital tuners Cable will not work unless you subscribe to a cable service PAGE 20 Auto Program Channel Labe
8. Setup for Cloning Overview e Set up Installer s remote control see page 19 e Do a Channel Search see page 20 e Channel List e Channel Label e Video picture appearance options setup see Picture menu e Audio sound options setup see Sound menu e Set up all other features See page 5 Table of Contents for a list of features available on this LCD TV Monitor Clone Master TV s Setup See Clone Programmer section Installation Connections Overview To hook up source equipment see below and also refer to the Table of Contents on page 5 shows pages to go to for equipment hookup options SPEAKER SWITCH Used to select the speaker output Note If Pillow Speaker is selected no Sound on will be heard from TV speakers AUDIO VIDEO 1 3 IN Switch NORMAL SPEAKER or PILLOW SPEAKER Connect Audio Video equipment to these jacks RS 232C SELECT SWITCH M P I INTERFACE Use with clone programmer UPDATE SWITCH _ VIDEO 1 SPEAKER SWITCH ie I RS 232C UPDATE RS 232C FUTURE PILLOW W NORMAL 4 SELECT USE SPEAKER SPEAKER I I I a PILLOW JACK IN CONTROL NORMAL kdi DTV py I AUDIO IN_ VIDEO IN RS 232C PORT FUTURE USE ANTENNA CABLE Connect to an antenna or HDMI DVI IN cable system PILLOW JACK IN Used to connect to pillow speaker 12V DC 40mA Note RS 232C Update Switch and RS 232C Select Switch are reserved for qualified and authorized service and technic
9. V Chip Setup Checklist Caption Menu Installation Connections Overview Sound Menu VESA Standard TV Mounts Picture Menu Managing the Channel Banks TV and other Equipment Hookup Antenna Installer Overview Cable Service Commercial Mode Setup Antenna amp VCR Cloning Connections Learning Setup Cable Service with VCR Cloning Programmer Learning Setup Pillw Speaker Hook Up Cloning Connections Teaching Setup Power Cord Hookup Installer Menu Front Panel Controls Reference Menus and Displays Overview L20V54S Aux Input Configuration Troubleshooting On Screen Menus Overview Troubleshooting Other Menus and On Screen Displays Reference Cloning Procedure Troubleshooting User Remote Control Key Functions Troubleshooting Flow Chart Installer Remote Control Key Functions TV Operation Check Glossary of Terms Step 2 Channel Search and Reception Setup Installer Quick Setup Guide Auto Program Do a Channel Search Notes Warranty Channel Menu Channel List Channel Labels Setup Optional USER and Installer Remote Controls for Model No L20V54S Shown herein is an optional Installer remote control available for the L20V54S model only The Installer remote control is NOT included with the LCD TV Monitor However both the User and Installer remotes can be purchased separately see your Zenith dealer Purchase the Optional Installer s Remote and Clone Programmer To perform a normal installation set up you need an installer s remote and the LT2002 Quicks
10. button Use the ADJ Left Right arrows to choose the menu options and the Up Down arrows to set the options When finished setting the clock press Menu repeatedly to remove the menus On Off Timers Setup ck 7 SSS Set the On Off Timers using the procedures described above Auto ee Note If you intend to use the On Off Timers it is best to set the aaa P l Auto Of clock manually Clock Manual Manual Clock m ce Fine Zone Pn eld E Lael Co 0 oe Ea PAGE 23 Clock Setup Continued Automatic Time Settings If you select auto time setting time will be set from the digital broadcast information Press the MENU button and then use the ADJ A V button to highlight the Setup menu Press the OK Enter button to highlight Time Press the OK Enter button to highlight Clock Manual or Auto will appear on the menu next to clock Select Auto on the submenu with the Down arrow and press the OK Enter button Clock Use the ADJ Up Down Left Right arrows to set the DEAT Send Daylight Savings and Time Zone options for your local co Woe A area See the next page When finished setting the clock press MENU repeatedly to remove the menus Caution Some digital channels may change the time incorrectly using the Automatic Clock Set feature Clock In this event the Alarm may not function as intended and the A set TV may not turn on at the expected time
11. button Use the Up Down Left Right arrows buttons to choose and set up the menu options for MPAA Rating LD A Press the MENU button several times to remove the Menu Transparency merik Rely f Description of the MPAA and TV FCC Rating Codes The MPAA Rating System Movies ChanomngiFIN G General Audience No restrictions nae PG Children under 13 should be accompanied by an adult N Ivecibatng PG 13 Parental guidance suggested Children under 13 should be MPAA Hang accompanied by an adult R Restricted Viewers should be 17 or older NC 17 Not classified Viewers should be 17 or older X Adults only e MPAA ratings The selected rating will be locked In addition any ratings that are more restrictive will also be blocked On Off MPAA Rating Can English Rating Can French Rating 11 20 PM Sep 11 2006 PAGE 29 V Chip Continued Canadian English Ratings 1 2 3 4 5 Press the MENU button and then use the ADJ A V button to highlight the Setup menu Press the OK Enter button Use the Down ADJ arrow to highlight V Chip and press the OK Enter button Use the Up Down Left Right arrows buttons to choose and set up the menu options for Canadian English Rating Press the MENU button several times to remove the menus Canadian English Ratings E Expect No restriction C Children C8 Viewers should be 8 or older G General Audience PG Parental guid
12. change operational settings See more detailed descriptions of the Installer menu items on the following pages Accessing the Installer s Menu Make sure TV is on Installer s menu items can be accessed by using an installer s remote control Just press MENU repeatedly at least 10 times until the TV seems to stop responding then press 9 8 7 6 then ENTER to access the Installer s menu To remove the Installer s menu press ENTER again Any changes you make will be stored in non volatile memory The menu also disappears automatically 000 INSTALLER SEQ The Installers menu opens with item 000 INSTALLER SEQ 000 Use the Up Down arrow keys to sequence through the available menu items Or access an item directly by keying in the line number then pressing MENU For example to access the Sleep Timer option UPN 000 000 000 000 FPGA 09F1 which is item 015 press 0 1 5 then MENU To change a setting use the Left Right TIG es Pee ieee arrow keys Or enter a value directly Typical Installer Menu Using the Installer s Menu Items 000 117 are immediately accessible only upon entering the Installer s Menu Their numbers descriptions ranges factory default settings and a place for listing any changes made on site are given below and on the following pages Installer Menu Items 000 through 117 Menu Item Function Value Range Default Value Brief Description of Function and Comments 000 INSTALLER SEQ 0 3 Leave defaul
13. directly accessing a channel not in the favorite channel list REVERT CH 0 oO If set to 1 and loss of M P I communication occurs TV tunes to Start Channel QUICK SHUTOFF oO Allows TV timed power off press and hold setup with pillow speaker channel button UPN MSB Iw uo oO User programmable number most significant byte UPN MSB 1 Iw uo oa User programmable number most significant byte 1 UPN MSB 2 Iw uo Oo User programmable number most significant byte 2 UPN LSB Iw uo oa User programmable number least significant byte CHKSM ERROR Enforces rigid M P I checksum HANDSHK TIME Relaxes M P I timing to be compatible with PC based Windows controlled systems PERMANENT BLK Removes block hours setting for Parental Control and makes block permanent EN NOISE MUTE KEY LOCK If set to 1 mutes audio if no signal is present If set to 1 keyboard is locked out IR is still functional SAP MENU EN Set to 0 to disable feature on Function menu Set to 1 to enable feature on Function menu DEF ASP RATIO Sets default aspect ratio at power up See detailed descriptions and item 106 ATSC BAND ATSC TUNE MODE Selects ATSC band Sets ATSC tuning mode Set to O for virtual channels set to 1 for physical channels START MINOR CH Selects Minor start channel Set 0 for NTSC Not 0 sets Minor channel number ASP
14. following describes the procedure for preparing a Master L20V54S for cloning and the procedure for adding Channel Icons and or Labels Note 1 Disconnect all Aux inputs Under certain conditions Auto Program Scan is disabled if there is an Aux input active 1 Enter the L20V54S installer menu a Reset the internal controller to factory default by accessing installer menu item 117 FACT DEFAULT set it to 1 and press ENTER The value will change back to 0 after the TV s internal controller has been restored to factory default condition b Within the Installer menu set the Installer menu items to the configuration required of your institution c It is important to set the tuning band at this time see Installer menu item 03 BAND AFC d Set Installer menu item 28 CH OVERIDE to 001 to allow access to the Auto Program and Channel List Channel Label features in the Channel Menu Exit the Installer menu Access the Master TV menus and set the clonable options on the menus to the desired configuration Refer to the Clonable Menu Features Chart on see page 52 Run Auto Program Enter the Channel List Channel Label menu and edit the channel line up to include the Free To Guest Channels only PAGE 52 adding channel icons or channel labels are not correctly added then the cloned L20V54Ss TVs will all have problems As the cloning procedure is being performed specific steps need to be done at the indicated times to achiev
15. menu THE CLONE HAS CONTROL OF THE TV menu is displayed on the TV screen the clone programmer LED is blinking the required heart beat pattern see above and next page Note Once the clone is connected do not touch the unit or otherwise disturb it or the MPI connections Any disturbance while the clone is operating may disrupt the master setup transfer or copying etc Before you begin cloning Setting the time and transferring it to the Clone or other e The Master L20V54S should be connected to a good stable device is a separate procedure signal from an over the air antenna or cable service Analog Follow the connection diagram above to connect the Clone to channel and connected to power See above a Master L20V54S TV display panel After learning is complete e Teaching and Learning is only possible between identical model to another identical L20V54S TV display panel to teach it the devices However the LT2002 Clone programmer can store up master setup to 3 different master setups After the L20V54Ss setup has been copied to another WARNING Copying a blank or incorrect memory into a TV STB or identical L20V54S that identical unit with the copied setup other device will cause the TV STB or other device to operate needs to be disconnected from power for about 15 seconds to erratically or become inoperable activate the newly copied setup Use an Installer s remote to operate Learning and Teaching See the Clone T
16. require the unit to be taken by the service to the repair facility and returned at no additional charge Call 1 888 865 3026 for further information Not Covered This warranty covers manufacturing defects and does not cover installation adjustment of customer controls installation or repair of antenna systems cable converters or cable company supplied equipment it also does not cover damage due to misuse abuse negligence acts of God or other causes beyond the control of LG Any alteration of the product after manufacture voids this warranty in its entirety THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTY EXPRESS OR IMPLIED INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AND NEITHER THE MANUFACTURER NOR ITS DISTRIBUTORS SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL INDIRECT OR INCIDENTAL DAMAGES OF ANY KIND INCLUDING LOST REVENUES OR PROFITS IN CONNECTION WITH THIS PRODUCT SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU OWNER S RESPONSIBILITY Effective Warranty Date Warranty begins on the date of installation of the Commercial Products LCD TV Monitor For your convenience keep the dealer s dated bill of sale or delivery ticket as evidence of the purchase date Operating Guide Read the Installation and Operating Guide carefully so that
17. that comes from an off air antenna or cable service provider The end looks like a hex shaped nut with a wire sticking through the middle It screws onto the Antenna Cable threaded jack on the back of the L20V54S 300 TO 75 OHM ADAPTER A small device that connects a two wire 300 ohm antenna to a 75 ohm RF jack They are usually about an inch long with two screws on one end and a round opening with a wire sticking out on the other end ANALOG TELEVISION Standard television broadcasting format in 4 3 picture aspect ratio A V CABLES Audio Video cables Three cables bunched together right audio red left audio white and video yellow A V cables are used for stereo playback of videocassettes and for higher quality picture and sound from other A V devices A V DEVICE Any device that produces video or sound VCR DVD cable box or television AMPLIFIER An electronic device that amplifies sound from a television CD player VCR DVD or other Audio Video device ANTENNA The physical receiver of television signals sent over the air A large metal piece of equipment does not always have to be visible to be using an antenna CABLE Cable service box Refers to the descrambler box cable subscribers use to receive cable programming signals CATV Programming provided by a cable service DIGITAL TELEVISION High resolution cinema quality television signals transmitted digitally DVI Digital Video Interface Accommoda
18. to 0 NOT AVAILABLE message is displayed when directly accessing a channel not in the channel scan list available in memory 075 REVERT CH Revert to Start Channel If set to 1 and loss of M P I communication occurs TV automatically tunes to the specified Start Channel 077 QUICK SHUTOFF Allows TV power off to be controlled by the pillow speaker channel selection button User would press and hold button down for time required to have TV turn off Value Range 0 17 each number represents 1 2 second For example if set to 4 TV would turn off if user held speaker channel button down for 2 seconds 078 UPN MSB UPN Most Significant Byte User programmable number most significant byte readable by M P I command Note Not linked to serial number 079 UPN MSB 1 UPN Most Significant Byte 1 User programmable number most significant byte 1 readable by M P I command Not linked to serial number 080 UPN MSB 2 UPN Most Significant Byte 2 User programmable number most significant byte 2 readable by M P I command Not linked to serial number 081 UPN LSB UPN Least Significant Byte User programmable number least significant byte readable by M P I command Not linked to serial number 082 CHKSM ERROR Checksum Error Enforces rigid M P I checksum validation Set to 1 for validation Set to 0 to disable does not check checksum on M P I async port SPI is always checked 083 HANDSHK TIME Handsh
19. user Sound Mode Setup Match the sound mode to the program s character Music Movie Sports or News Press the MENU button and then use the ADJ A button to highlight the Sound menu Mode Standard gt Balance Press the OK Enter button IN Auto Volume Mult Track__ Engis With Mode highlighted press the OK Enter button Use the A V lt 41 gt ADJ buttons to customize each option or choose a preset mode like Music Movie etc Sep 11 2006 When finished press the MENU button several times to remove the menus Sound Balance Setup Adjust the speaker balance for optimum sound quality Press the MENU button and then use the ADJ A V button to highlight the Sound menu Press the OK Enter button Use the Up Down arrow button to highlight Balance press the OK Enter button Use the lt gt ADJ buttons to move the sound more to the Left or Right Sep 11 2006 When finished press the MENU button several times to remove the menus Automatic Volume Control Settings Have the TV automatically maintain the sound level between different channels Press the MENU button and then use the ADJ A V button to highlight the Sound menu Modes Baines E Balance BEIB css the OK Enter button mrem ae intemal Speaker Use the Up Down arrow button to highlight Auto Volume z 5 press the OK Enter button Use the 1 gt ADJ buttons to choose On or Off Press the MENU b
20. you will understand the operation of the unit and how to adjust the controls Antenna Reception problems caused by inadequate antenna or faulty antenna connections are the owner s responsibility Warranty Service For warranty service information call 1 888 865 3026 Parts and service labor that are LG s responsibility see above will be provided without charge Other service is at the owner s expense If you have any problem in obtaining satisfactory warranty service call 1 888 865 3026 e You must provide the model number serial number and date of purchase or date of original installation e Before you ask for warranty service read Troubleshooting in this installation guide You might avoid a service call For Customer Support Service Please call 1 888 865 3026 www zenith com www lgcommercial com Marketed and Distributed in the United States by LG Electronics U S A Inc 2000 Millbrook Drive Lincolnshire IL 60069 P NO 3350GDKM0014A Copyright 2007 LG Electronics U S A Inc GPNO7MA003A
21. 28 Ch Overide back to 000 Note Default setting for Aux sources is to be active in the installer menu The Aux sources will appear between the highest Analog and lowest Digital channel number with Channel Up Down If the Aux sources will not be used it is advisable to set them to 000 Off before doing 2 5 5 Menu After doing 2 5 5 Menu the only way to turn the Aux source off so they will not appear in the channel scan is to go to the Channel Bank menus and turn each Aux source off by selecting Normal Delete Refer to installer items 35 39 Cloning Connections Learning Setup Connections for the LT2002 Clone Programmer to Learn the L20V54S Master TV Setup 2 ON Z Antenna or CATV Ferrite Core TDK ZCAT 2035 0930 THE CLONE HAS CONTROL OF THE TV THE CLONE IS VERSION THE TV IS VERSION THE SW IS REVISION QuickSet Il Programmer Warning Do not use LT2002 WeLecK HK LT2002 if a LodgeNet PPV card is PRESS ANY KEY TO CONTINUE installed in TV or clone DISCONNECT CLONE WHEN DONE programmer device will be damaged Clone Programmer Master L20V54S Note It is assumed that the L20V54S is connected to a signal source the source selected is Antenna RF In the signal is from an Analog channel not a digital channel all equipment is connected to power and turned on and the LT2002 Clone Programmer main
22. ID display With the Up or Down arrow select the desired ICON you want to appear to identify the channel If you know the ICON number enter the number followed by Enter Select Note If no Icon is available leave at or select the default blank icon display 4 Proceed with Changing Adding Labels or go to the next channel desired character channel Changing Adding Channel Labels on Editing and adding the labels can only be done if there are channels entered into the L20V54S s channel map either by using the method described in item 6 page 51 by cloning or by the use of the master remote control from the PPV provider To Do Channel Editing Labeling proceed as follows 1 Enter L20V54S Installer menu 2 After the installer menu appears press 2 5 4 MENU This enters the channel label edit mode Add your channel icons and channel labels in this menu see below You can do this more than once 3 To exit the menu when done press MENU Changing Source Labels on Master TV 1 Press TV AV to select the desired Aux input source Video 1 HDMI 2 Press the Right or Left arrow repeatedly until the numbers 0 to 9 show up The number shows the position of the character that can be changed Use the Up or Down arrows to select the desired character Press TV AV for the next Aux source or proceed with Changing Icon or Changing Adding Labels Proceed to the next numb
23. Installation and Operating Guide Warranty Model Number L20V54S LCD TV Monitor VY table of contents ee GD VY installer quick setup guide Snead tne TD zenith Zoe Zenith and the lightning Z logo are registered Copyright 2007 LG Electronics U S A Inc trademarks of Zenith Electronics Corporation RECORD THE MODEL NUMBER For Customer Support Service please call The model and serial number of this LCD TV Monitor are 1 888 865 3026 located on the back of the cabinet For future reference we suggest that you record the serial number here www zenith com MODEL NO L20V54S www lgcommercial com SERIAL NO CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER TO QUALIFIED SERVICE PERSONNEL presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude h The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance WARNING TO PREVENT FIRE OR SHOCK HAZARDS DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE THIS PRODUCT MUST BE
24. ON LOCK Set to 1 to restore previous caption On Off state after turn Off If set to 0 captions are always Off at turn On 025 FUNCTION PRE Function Preview Set to 0 to suppress CHANNEL PREVIEW from the FUNCTION menu with some Pay Per View systems 027 HOSPITAL MODE The default is 2 which favors most hospitals With this setting two things are affected Channel Banks 1 2 and 3 are accessible while Bank 4 is inactive 028 CH OVERIDE Channel Override If set to 1 the user can select channels with either Channel up down or by direct keypad entry If set to 0 only those channels that are entered for scanning can be selected 029 OLD OCV On Command Video Set to 1 for operation with systems from On Command Corporation 030 ACK MASK M P I Communication Parameter Leave at default setting unless changed by Pay Per View provider When set to 1 changes M P I for some OCV boxes 031 POLL RATE M P I Communication Parameter Selects Poll Rate for M P I Leave at default setting unless changed by Pay Per View provider Step size of 16 ms 032 TIMING PULSE M P I Communication Parameter Leave at default setting unless changed by Pay Per View provider Sets baud rate Step size of 4 3 uS 035 COMPPORT EN Computer Port Enable Enable disables display panel HDMI input jack Set to 0 to disable set to 1 to enable Installer Menu Detailed Descriptions of Installer Menu Items 039 REAR AUX EN
25. ONNECT CLONE WHEN DONE This menu should appear by itself after the LT2002 is connected to the L20V54S MPI port CLONE SELECTION MENU LEARN FROM TV TEACH TO TV SET CLONE CLOCK FROM TV SET TV CLOCK FROM CLONE DISPLAY TV SETUP DISPLAY CLONE SETUP TO CHANGE MENU ITEMS PRESS CHANNEL KEYS OR DIGITS TO EXECUTE ITEM PRESS ON OFF POWER OR ENTER LT2002 Clone Programmer Communication Problems e A slow flashing green light indicates there are communication problems between the L20V54S and the LT2002 clone programmer If this is the case check for a damaged cable poor contacts or other connection troubles e If the status indicator is red the programmer batteries are low and should be replaced Install 4 high quality alkaline AA batteries PAGE 43 Cloning Connections Teaching Setup Teaching the Master Setup to Another L20V54S Connections for the LT2002 to Teach another L20V54S the Master Setup Antenna or CATV THE CLONE HAS CONTROL OF THE TV THE CLONE IS VERSION THE TV IS VERSION THE SW IS REVISION CLONE CLOCK XX XX TV CLOCK XXX PRESS ANY KEY TO CONTINUE DISCONNECT CLONE WHEN DONE Master L20V54S Teach Master L20V54S s Setup to the target L20V54S After learning is complete remove the M P I cable from the master L20V54S and connect it to the target L20V54S that you want to copy the master L20V54S s setup into With THE CLONE HAS CONTROL OF TV
26. OW NORMAL SELECT use senen C speaken After all connections are complete F wx plug in the TV The LCD TV Monitor is ETE designed to operate on AC power Connections Panel RF Coaxial o o i Wire 75 ohm For cable box operation leave the television tuned to channel three or four and use the cable box to change channels Cable TV Wall Jack Ne SPEAKER SWITCH PLLOW C NORMAL SPEAKER SPEAKER RS 232C FUTURE SELECT USE AP ocen OO CAN D soma CONTROL NORMAL ory Connections Panel n Cable Box A output out switch OCT Coaxial Wire RF 75 ohm Mini glossary 75 OHM RF CABLE The wire that comes from an off air antenna or cable service provider Each end looks like a hex shaped nut with a wire sticking through the middle and it screws onto the threaded jack on the back of the TV 300 TO 75 OHM A small device that connects a two wire 300 ohm antenna to a 75 ohm RF jack They are usually about an inch long with two screws ADAPTER on one end and a round opening with a wire sticking out on the other end PAGE 10 Antenna amp VCR Hookup Connect antenna and a VCR to the LCD TV Monitor Locate the Antenna Cable jack on the back of the VCR Connect the antenna wire that runs from the wall jack to the VCR Connect other wires according to the diagram to the right After all connections are complete plug in the TV The LCD TV Monitor is designed to operate on AC po
27. RATIO LOCK ojoje RI MIP OTPRP oOo mo To retain set aspect ratio on power cycle set to 1 Set to 0 for default ratio on power cycle BANNER SELECT Not applicable VIDEO MUTE EN Set to 0 for normal set to 1 for Blank FACT DEFAULT 0 Normal 1 Loads factory default presets of all above settings PAGE 46 Installer Menu Detailed Descriptions of Installer Menu Items 000 INSTALLER SEQUENCE Specifies entry sequence to the Installer Menu 0 9876 1 4321 2 1478 3 3698 001 POWER MANAGE Power Management Determines hours of no activity before automatic shutoff The POWER MANAGE function is for saving energy If set to 0 Power Manage is Off Settings range from 0 7 with 1 7 representing the hours that the TV will remain On unless there has been activity from either the control panel or remote control 002 AC ON AC Power Switchable If set to 1 allows the L20V54S to turn On just by applying AC power Pressing the On button is not necessary This is desirable if the L20V54S is plugged into a cable box or a power outlet controlled by a wall switch Use ADJ Left Right arrow to choose 0 or 1 where 0 is the default is Off and 1 is On Note If set to 1 On the L20V54S does not respond to On Off commands from either the remote or the display control panel and the SLEEP TIMER is also nonfunctional 003 BAND AFC Band Automat
28. Speaker output jack on the back of the LCD TV Monitor Connect an accessory pillow speaker or wired remote control unit to this 6 pin jack Select PILLOW SPEAKER on the rear panel of the suo Cy nora LCD TV Monitor PILLOW JACK IN J 12V DC 40mA Notes If the pillow Speaker switch is set to Pillow Speaker no sound will be heard from the TV speakers If pillow speaker switch is set to the Pillow Speaker position Auto Volume will be grayed out and not accessible on the Sound menu Use a pillow speaker by Curbell Model A 16455 02 or other UL recognized pendant control bearing the warning Risk of fire if used in oxygen enriched atmosphere Keep pendant control away from oxygen equipment Pillow speaker not included with LCD TV Monitor Controlling the TV with Serial Data The TV is capable of being controlled by a single wire serial data signal This is a Zenith patented technology and is being implemented by certain brands of smart pillow speakers such as Curbell s GEN II models Pillow Speaker Interface This connector furnishes three control lines and an audio output A patient pendant remote control or entertainment audio and nurse call system may be connected here All lines are isolated from the AC power line and earth ground Opto isolators isolate the control lines and a transformer isolates the audio There are no relays or inductive components in the control lines v 4 ON OFF
29. TV s Clock If the time has already been copied from a TV into the Clone programmer you can set a master TV s clock by copying the time from the Clone programmer The Clone Programmer can copy the current time to both a master TV and to the Clone s internal clock accurate to within one minute Another reason that the Clone programmer should be equipped with fresh high quality alkaline batteries is for it to keep the time as accurately as possible Since the Clone Programmer s time cannot be set directly the current time needs to be copied from a Zenith LG TV equipped with M P I input capability After the time is copied to the Clone programmer the current time can then be transferred to another TV This can be a master TV or another TV which has already had the features set up Note When using the clone programmer for teaching or learning be sure that the heartbeat pattern is shown on the LEDs Both learning and teaching should take about 45 or more seconds depending on the complexity of the master setup While the clone is functioning do not move it or otherwise disturb the clone or wiring connections If the clone finishes the function in less than 45 seconds redo the function again Press the reset button if the clone does not act normally THE CLONE HAS CONTROL OF THE TV THE CLONE IS VERSION THE TV IS VERSION THE SW IS REVISION CLONE CLOCK XX XX TV CLOCK XX XX PRESS ANY KEY TO CONTINUE DISC
30. USED WITH UL LISTED MOUNTING BRACKET X IT IS FORBIDDEN TO CONNECT THIS TV TO ANY TELECOMMUNICATION NETWORK TELEPHONE NOTE TO CABLE TV INSTALLER This reminder is provided to call the CATV system installers attention to Article 820 40 of the National Electric Code U S A The code provides guidelines for proper grounding and in particular specifies that the cable ground shall be connected to the grounding system of the building as close to the point of the cable entry as practical REGULATORY INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures eReorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipmen
31. able to touch this product 3 This product should only be mounted on a wall CLEANING AND DISINFECTION Clean the exterior of this television by removing dust with a lint free cloth CAUTION To avoid damage to the surface of the television do not use abrasive or chemical cleaning agents DISCONNECTING DEVICE FROM MAINS Main plug is the disconnecting device The plug must remain readily operable IMPORTANT SAFEGUARDS FOR YOU AND YOUR NEW PRODUCT YOUR PRODUCT HAS BEEN MANUFACTURED AND TESTED WITH YOUR SAFETY IN MIND HOWEVER IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS TO AVOID DEFEATING THE SAFEGUARDS THAT HAVE BEEN BUILT INTO YOUR NEW PRODUCT PLEASE READ AND OBSERVE THE FOLLOWING SAFETY POINTS WHEN INSTALLING AND USING YOUR NEW PRODUCT AND SAVE THEM FOR FUTURE REFERENCE OBSERVING THE SIMPLE PRECAUTIONS DISCUSSED IN THIS MANUAL CAN HELP YOU GET MANY YEARS OF ENJOYMENT AND SAFE OPERATION THAT ARE BUILT INTO YOUR NEW PRODUCT Notes If the TV feels cold to the touch there may be a small flicker when it is turned on This is normal there is nothing wrong with the TV Some minute dot defects may be visible on the screen appearing as tiny red green or blue spots However they have no adverse effect on the TVs performance Avoid touching the LCD screen or holding your finger s against it for long periods of time Doing so may produce some temporary distortion effects on the screen PAGE 3
32. ake Time Adds an additional delay to the handshake time which is 64 msec thus relaxing M P I timing requirements to be compatible with PC based Windows controlled systems range is 0 5 Timeout 25 5MS 25 5 MS Handshake time 084 PERMANENT BLK Permanent Block Allows Lock Parental Control blocking schemes to be permanent by disabling the blocking hours function Set to 1 to install Parental Control restrictions permanently Set to 0 for user specified hours control of blocking schemes 088 EN NOISE MUTE Enable Noise Mute If set to 1 audio mutes if no signal is present 090 KEY LOCK If set to 1 display panel keyboard is locked out not available to end user IR receiver remains functional 094 SAP MENU EN 2nd Audio Program Set to 1 to enable SAP feature if available Set to 0 to disable SAP feature 096 DEF ASP RATIO Default Aspect Ratio Selects default aspect ratio at power up see settings below Set to 0 for set by program Set to 1 for 4 3 Set to 2 for 16 9 Factory Default Set to 4 for Zoom 1 Set to 5 for Zoom 2 102 ATSC BAND Sets up TV to receive different types of incoming signals 0 Broadcast 1 CATV 2 HRC 3 IRC 4 Same as NTSC Continued on next page PAGE 49 Installer Menu Continued from previous page 103 ATSC TUNE MODE Selects ATSC tuning mode 0 Virtual 1 Physical Note The setting above is ignored if Installer i
33. al Font Options if any default setting is left unchanged prior to cloning then all the digital font options wil be set to default settings If you want custom digital font options to be clonable set all digital font options to settings other than Default PAGE 50 Reference Procedures for adding Channel Label Icons Custom Channel Labels 2 5 4 MENU Mode Adding Channel Icons and Labels in the 2 5 4 Menu Mode Editing Adding Channel ICONs and or Labels If there is no pre assigned ICON you can make a channel label of up to 7 characters to help in identifying the channel or network At your option channel labels can also be added in addition to a pre assigned ICON You may also add labels for the Aux input sources to clearly identify the devices that are connected to the Aux inputs Icon XYZ CO gt NETWORK Label 1234567 Changing a Channel s ICON on Master TV Master TV With Channel Up Down select the channel 1 Channel Up Down to select the desired you want to change the Icon for channel With the Right or Left ADJ arrow select 2 Press the Right or Left ADJ arrow repeatedly until the numbers 1 to 7 show up The number shows the position of the character that can be changed Number 1 is the first character number 2 the second character and so on With the Up or Down arrow select the the letter I on the channel
34. al support personal only VESA Standard TV Mounts VESA Standard 100mm TV Mounts and Stands Following are shown some examples of VESA standard 100 mm mounts Since there are numerous types of stands and mounts available only a few are shown here Refer to the instructions provided with the TV stand that will be used to mount the TV Typical Wall Stud Type Mount with Swivel Bracket 100mm v General Guidelines Choosing a location for installing a VESA Standard Mount Typical Pedestal Type Mount with Swivel Bracket Be sure the style of stand selected is capable of supporting the weight of the TV If the mount will be on a wall a typical wooden stud behind the wall board would be the preferred choice for a location to attach the wall mount The wall mount location chosen should be appro priate for drilling holes and have available the required power source as well as antenna cable and other equipment leads For pedestal type mounts a sturdy surface on a desk or other similar flat table like surface would be the appropriate location for mounting a pedestal style TV stand Some stands are portable and can be moved from one location to another Be sure all safety considerations are followed Most stands are designed so that the wiring would be threaded through the stand itself or a loop through style clamp so that the wiring is neatly bunched and not strung in such a way as to create a po
35. aller s remote control available to use to set up the TV This is a must for TV setup Yes No___ Master TV Setup Will the Master TV s features setup be cloned and be copied to other identical LCD TV Monitors Yes No LT2002 Quickset II Clone Programmer To copy the TV s setup the installer will need a clone programmer Is there a Zenith LT2002 Clone Programmer available Yes No___ End User Remote Control Will a remote control be provided to the end user to operate the TV No remote is included with the TV Yes No___ End User Menu Access Will the end user have access to all the menus on the TVs from the front panel Yes No LCD TV Monitor Setup Checklist 1 Install the LCD TV Monitor where it will be used Prior to Operation The LCD TV Monitor must be connected to all external antenna cable video and audio source equipment and AC power source See page 5 Table of Contents 2 Make all external source equipment connections See pages 10 14 3 Connect the LCD TV Monitor to a standard 120V 60 Hertz AC power source See page 14 4 Turn on the TV and all source equipment Review TV Setup Options in the Installer s Menu Section The Installer s menu includes a number of options for the master TV s setup that enable the installer or system administrator to devise a unique system using the many different options and variables available See Installer s menus section Master TV Features
36. amic or Mild etc Press the MENU button and then use the ADJ A V button to highlight the Picture menu a moes O Color Temperature Screen Format Noise Reduction Press the OK Enter button Use the Up Down arrow button to highlight Mode press the OK Enter button 11 20 PM Sep 11 2006 Use the lt P ADJ buttons to choose a preset picture setup When finished press the OK Enter button Press the MENU button several times to remove the menus Custom Color Setup Use the Manual settings for the best presentation of movies The patient will then be able to view movies with more realism To make custom picture settings set the Mode to Manual on the menu Mode Contrast 1100 3 S Format iNES mm Press the MENU button and then use the ADJ A Y button os pee as 7 to highlight the Picture menu Color 70 Tint jms Press the OK Enter button Sep 11 2006 Use the Up Down arrow button to highlight Mode press the OK Enter button Use the lt P ADJ buttons to choose Manual and use Up Down Left Right arrow buttons to set your own set tings for the options When finished press the OK Enter button Press the MENU button several times to remove the menus PAGE 35 Picture Menu Continued Color Temperature Settings Press the MENU button and then use the ADJ A V button to highlight the Picture menu Press the OK Enter button Use the Up Down arrow button to choose Colo
37. ance suggested Children under 14 should be accompanied by an adult 14 Restricted Viewers should be 14 or older 18 Restricted Viewers should be 18 or older Canadian French Ratings Press the MENU button and then use the ADJ A V button to highlight the Setup menu Press the OK Enter button Use the Down ADJ arrow to highlight V Chip and press the OK Enter button Use the Up Down Left Right arrows buttons to choose and set up the menu options for Canadian French Rating Press the MENU button several times to remove the menus Canadian French Ratings E Expect No restriction G For all 8 Restricted Viewers should be 8 or older 13 Restricted Viewers should be 13 or older 16 Restricted Viewers should be 16 or older 18 Restricted Viewers should be 18 or older PAGE 30 11 20 PM Sep 11 2006 11 20 PM Sep 11 2006 11 20 PM Sep 11 2006 11 20 PM Sep 11 2006 11 20 PM Sep 11 2006 V Chip Changing PIN TVPG Rating MPAA Rating Can English Rating Can French Rating Can French Rating Caption Menu Turn Captions On Off Note Pressing CC on the remote to select a captions option will also turn closed captions on Press the MENU button and then use the ADJ A V button to highlight the Caption menu Press the OK Enter button Use the Down ADJ arrow to highlight On or Off and press the OK Enter button Press the MENU button severa
38. ated does not appear there is a problem with that step and cloning may not be successful Cloning is __ only possible when the signal source is an QuickSet Il Programmer Analog channel not a digital channel LT2002 ZENITH ELECTRONICS CORPORATION LINCOLNSHIRE ILLINOIS USA PAGE 40 L20V54S PTC INSTALLER MENU INSTALLER SEQ UPN 000 000 000 000 FPGA 09F1 PTC V1 00 000 CPU V1 01 00 Typical Installer Menu CH BANK PREVIEW GUIDE SAP INFO cc 0 O 0O O O O FLASHBK 0 TIMER MENU ALARM ADJA ADJ lt ADJY ADJP BED1 Gam BED2 Commercial Mode Setup This page provides an overview of the TV configuration See the pages listed below for more specific detailed instructions at each step how to access and use the Installer menu etc Note 1 Disconnect all Aux inputs Under certain conditions Auto Program Channel search is disabled if there is an Aux input active Overview Commercial Mode Setup Procedure 1 Set Installer Menu Items Enter Installer Menu see page 43 for detailed instructions a Set Installer menu item 117 FACT DEFAULT to 001 and press ENTER This clears all installer menu items custom settings channel labels icons and reloads the factory default settings b Set Item 003 BAND AFC Broadcast set to 000 HRC set to 002 CATV set to 001 IRC set to 003 Set item 028 CH OVERIDE to 001 This allows acce
39. creen display or menu BED 1 BED 2 See Note Below Determines the code set transmitted Bed 1 or Bed 2 Switch setting must correspond to item 27 HOSPITAL MODE setting in the TV s Installer Menu CHANNEL PREVIEW Displays available TV channels and if active the Guest Parental Control menu set V Chip blocks to restrict both analog and digital programming e Aux Channel allows the guest to select the Audio Video inputs Use the A V jacks on the back of the TV as a source Optional Patient Remote Control Part Number Note Bed 1 Bed 2 switch on patient remote The position of the Bed 1 Bed 2 switch must correspond to the setting in the Installer s menu The switch above can be set by sliding it to the Bed 1 or Bed 2 position On the patient s remote the Bed 1 or Bed 2 position can be selected by using a paper clip or a ball point pen to slide the switch to the correct position Left position Bed 1 Right Position Bed 2 PAGE 18 Installer Remote Control Key Functions A brief list of the keys on the optional installer s remote and what they do MUTE Turns sound Off and On while the picture remains BANK Press and repeat to select a Channel Memory Bank 1 2 3 or 4 Standby SAP Selects MTS sound Mono Stereo and SAP in analog mode Change the audio language in DTV mode CHANNEL PREVIEW Displays available TV channels and if active the Guest Parental Control menu set V Chip block
40. d key it in using the num ber keypad If no password has been set enter a 4 digit password 0 9 using the remote control This is the PIN Each time the menu is entered the password will be required until the block time expires The TV is set up with the default password 0 0 0 0 Press the MENU button several times to remove the menus If you ever forget your password key in 7 7 7 7 on the remote control Mime a yono Menu Language Language 11 20 PM Sep 11 2006 Menu Transparency Transparency V Chip Menu Language Tansparency et ID Changing PIN TVPG Rating MPAA Rating an English Rating an French Rating Changing PIN TVPG Rating a MPAA Rating Confirm PIN oobi Ea Can French Rating Changing PIN TVPG Rating an English Rating Can French Rating PAGE 27 V Chip Continued TVPG Ratings You can block programs based on the TV program rating Time gt Press the MENU button and then use the ADJ A V button me to highlight the Setup menu Menu Transparency Press the OK Enter button 11 20 PM Use the Down ADJ arrow to highlight V Chip and press the Sep 11 2006 OK Enter button Use the Up Down Left Right arrows buttons to choose and set up the menu options for TVPG Rating Press the MENU button several times to remove the menus Description of the TV FCC Rating Codes TV FCC Age Catego
41. dd Aux Source Labels e Did you adjust all TV menu options as required The TV master setup is now ready to be cloned Go to the master TV cloning section or continue on to page 53 Reference Software Version Check Procedure to Check Software Version The software version of the L20V54S may be checked by accessing the INSTALLER MENU To do this press the MENU button at least 10 times until the menu display ceases to respond to MENU key presses Then press 9 8 7 6 OK Enter Select L20V54S PTC INSTALLER MENU 000 INSTALLER SEQ UPN 000 000 000 000 FPGA 09F1 PTC V1 00 000 CPU V1 01 00 Typical Installer Menu PAGE 53 L20V54S Aux Input Configuration Troubleshooting L20V54S Aux Input Configuration ENABLE MPI DATA DIRECT ACCESS MPI DATA DATA STATUS DATA patie i L20V54S STATUS TYPE TYPE 0xD2 STATUS AUX Tunin 9 Installer Menu 0x41 A CURRENT T TYPE0X0D SOURCE ENABLED R W SOURCE R AUX ASSIGNMENT LD OCV D V SOURCE Rear Video Rear Video Video1 Rear CV ONLY REAR_AUX_EN Aux Aux Front Front DVI HDMI1 DTV PC Auto COMPPORT EN Computer Computer Troubleshooting Some quick and easy tips to resolving problems Symptoms Possible Cause s Possible Solution s See Page s Software Problems TV not functioning Software lockup Remove power cord for 5 minutes properly Software Corrupted 2 5 5 MENU performed Start all over with item 117 set to 001 press Enter then red
42. e the desired result Be sure to do each task as indicated If a procedure or step is left out or not performed completely cloning may not work At each step pay attention to assure the TV screen shows the proper message when cloning If the message indicated does not appear there is a problem with that step and cloning may not be successful Cloning is only possible when the signal source is an Analog channel not a digital channel Assign ICONs to the channels using the Channel Label Menu Note You can add Channel ICONS typically network logos like ABC NBC PBS etc in this step Or in Step 7 add Channel ICONS or labels for channels without Icons Transfer the TV setup Enter the L20V54S installer menu Press 2 5 5 MENU to start the transfer of the TV s setup to the L20V54S Once the transfer is complete the system will exit the Installer menu Note Only do 2 5 5 MENU once The TV setup may be corrupted if 255 Menu is done more than one time Edit Add Channel ICONs and Channel Labels as needed Enter Installer menu With menu displayed press 2 5 4 MENU See page 50 for detailed instructions Editing Adding Channel ICON and Labels on Master TV Changing a Channel s ICON on Master TV Changing Adding Channel Labels on Master TV Changing Source Labels on Master TV Verify Master TV setup and feature configuration e Did you add Channel ICONS e Did you add Channel Labels e Did you a
43. ed when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or object have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped Outdoor Antenna Grounding If an outside antenna or cable system is connected to the product be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built up static charges Article 810 of the National Electrical Code U S A ANSI NFPA 70 provides information with regard to proper grounding of the mast and supporting structure grounding of the lead in wire to an antenna discharge unit size of grounding conductors location of antenna discharge unit connection to grounding electrodes and requirements for the grounding electrode Example of Grounding According to National Electrical Code Instructions Antenna Discharge Unit NEC Section 810 20 Grounding Conductor NEC Section 810 21 Electric Service Equipment Ground Clamps Power Service Grounding Electrode System NEC Art 250 Part H NEC National Electrical Code Table of Contents The table of contents lists the pages to go to for setting up the features for the end user Safety Warnings Step 3 Customize the TV s Features Important Safety Instructions Setup Menu Table of Contents Clock Setup Menu Language Step 1 LCD TV Monitor Installation and Connections
44. en Menus Overview Descriptions of the menus and on screen displays Menu Name CHANNEL MENU Auto Program Channel List Channel Label Fine Tune Signal Strength SETUP MENU Time V Chip Menu Language Menu Transparency Set ID CAPTION MENU SOUND MENU PICTURE MENU Channel Bank Volume Sleep Timer SAP Captions Alarm Guide Channel Preview gt V Chip Info Installer Menus PAGE 16 Page Description ON SCREEN MENUS Adjusts the basic operational features of the TV 21 Automatically finds and stores active channels to scroll through using Channel Up Down 22 Manually picks and chooses which active channels will appear when using Channel Up Down 23 Labels the channels with their network names ABC CBS HBO etc Automatically adjusts the picture for optimum appearance Reveals the strength of the incoming digital signal Sets the time Sets up restrictions or changes the password for Parental Control Picks the language the on screen menus will appear in Selects the degree of menu opacity Specifies the TVs identity 32 Chooses analog and digital captioning options 34 Sets up the sound Options are Mode Balance Auto Volume Multi Track Internal Speaker 36 Sets up the picture appearance f Options are Mode Color Temperature Screen Format Noise Reduction Film Mode 38 Show currently selected channel bank 18 OTHER MENUS AND ON SCREEN DISPLAYS Shows current sound level Se
45. enu to exit Enter the Installer menu Set item 028 Ch Overide to 000 and exit menu 028 CH OVERIDE 000 DIGITAL 19 3 ANALOG 2 WXYZ MONO Antenna Auto Program Seas Channel Label s7 Channel List Signal Strength Strength ANALOG34 0 Antenna Auto Program gt Channel Label Label Signal Strength Strength eal Notes PAGE 61 Notes PAGE 62 Notes PAGE 63 Your Zenith LCD TV Monitor Warranty zenith LCD TV Monitor Welcome to the LG family We believe that you will be pleased with your LCD TV Monitor Please read this warranty carefully it is a LIMITED WARRANTY as defined under Federal Law This warranty gives you specific legal rights and you may also have other rights that vary from state to state within the U S A LG S RESPONSIBILITY Service Labor During a period of one year from effective warranty date LG will provide service labor by a LG authorized service center when needed as determined by the LG service center as a result of manufacturing defects New or remanufactured replacements for factory defective parts will be supplied by an LG authorized service center for one year from effective warranty date color picture tube two years Such replacement parts are warranted for the remaining portion of the original warranty period Warranty Service Warranty service is provided Some repairs may
46. er items as required of your system Exit Installer menu Access the Master TV menus and set the clonable options on the menus to the desired configurations Refer to the Clonable Menu Features Chart for the TV Picture Sound Time etc Mode Standard gt Balance Auto Volume Volume Intemal Speaker 11 20 PM Sep 11 2006 ooo standara gt Color Temperature KO a 1 100 Brightness im 79 Noise Reduction GEESE U IGES ame 65 Film Mode Color ale Tint es 11 20 PM Sep 11 2006 PAGE 60 Do a Channel Search run Auto Program aka EZ Scan Enter the Channel Edit menu and delete channels per your requirements Enter the Channel Label menu and assign ICONs to the channels Note You can add Channel ICONStypically network logos like ABC NBC PBS etc in this step Or in Step 8 add Channel ICONSor custom text labels for channels which no Icons are available for Transfer the TV setup After all menu options and features are set to your requirements enter the installer menu Press 2 5 5 MENU to start the transfer of the TV s setup to the PTC After the transfer is complete the system will exit the Installer menu Set any Channel Labels as needed a Enter Installer menu b Press 2 5 4 MENU to enter the menu In this menu edit the assigned channel Icons assign custom text labels for channels and assign labels for active Aux sources Press M
47. er position or use Channel Up Down to go to the next Installer Remote Control Key Functions for Master TV Channel Editing Labeling Menu e CHANNEL Up Down Tunes in the next channel in scan e Left Right Arrows Select the item to change If I is shown the ICON can be changed If a number is shown it indicates the position of the character that can be changed e Up Down Arrows Select the ICON or the character to be displayed e 0 9 Use to enter the index number of the ICON if known OK Enter Select Changes the ICON after the number has been entered TV AV Changes the Aux input label This key is located on side of set and on Installer remote control MENU Exits the labeling editing menu PAGE 51 Reference Detailed Information For Making A Master TV IMPORTANT INSTALLER SETUP INFORMATION PLEASE READ THE FOLLOWING To set up a master TV you will need to know how to enter the L20V54S Installer menu and make changes to the default values as required If necessary familiarize yourself with the L20V54S Installer menu and how to make and save changes in the menu before attempting to clone the L20V54S Master TV setup You will also need an Installer remote control similar to the one shown in the front of this manual Finally the TV s clonable features need to be set up This is a critical step If the Master TV display panel s clonable features like Making a Master TV Detailed Instructions The
48. et II Clone Programmer both are shown and described in later sections See your Zenith LG dealer if you wish to purchase the Installer remote and LT2002 The installer remote allows access to the Installer menus User menus and Channel Banks in the Manual Channel Set options on the Setup menu The installer remote has Menu Select and Adjust Keys The LT2002 Quickset II Clone Programmer is used to duplicate a TV s setup and install it on another identical TV Note Design and specifications are subject to change without prior notice Setup Checklist Installation Overview e Unpack the LCD TV Monitor and all accessories Determine installation location for the LCD TV Monitor TV stand or mount Determine mounting and installation requirements If used AC Power source outlet Antenna Cable service connectors any external equipment required for system or TV operation all necessary cables wires connectors and any other additional required hardware etc Installation Overview amp System Setup Questions to Consider Before Installation VESA Bracket Does the VESA Bracket have to be mounted to the TV Y Install VESA Bracket on TV following the instructions supplied with the bracket Yes No___ TV Stand Does the TV have to be mounted on the stand Y Mount the TV on the stand following the instructions provided with the TV stand Yes No___ Installer s Remote Control Does the Installer have an the optional Inst
49. et TV for about 15 seconds Problem Possible Cause s Possible Solution s Remote does not e Wrong Installer remote Only use an appropriate Installer remote to operate clone programmer operate clone with L20V54S LED does not blink e M P I cord not connected Connect M P I cord e L20V54S not turned on L20V54S must be powered On for clone to work e Weak batteries Install 4 fresh AA high quality alkaline batteries Clone menu hard to e Weak signal Connect L20V54S to a reliable Analog channel signal source read No time set Time not available Set time on a TV copy time to Clone Programmer Clone not working Clone programmer problem Try a different LT2002 Clone programmer Reset Clone Programmer Clone Scans Channels e Clone should only scan Retry cloning again more than once channels once Master and Other L20V54S Cloning did not work e Procedure interrupted Wait until procedure complete message is displayed e Different TV models Cloning is only possible with identical model TVs Step s omitted or not performed Reread 43 44 45 pages to be sure all tasks were performed e Insufficient cloning time Redo cloning and be sure learning teaching time is about 1 min and 5 to15 seconds 75 seconds e Cloning erratic Reset Clone Programmer Clone time disappeared Batteries were removed Batteries must remain installed to retain time settings New Setup not presen
50. g AUTO PROGRAM Figure 2 Typical channel banks after running Auto Program and customizing with Add Del Blnk B Channel Number A PEP E PPP Basic BC Extend BC AJA BCCAMCI CS HEMA apa TOTAAL x OLA TR eea EEE E e e eE A Active Channel was found during AUTO PROGRAM D Delete Channel was deleted using Add Del option BC Blanked Channel Channel was blanked using BLANK channel option ADD DEL BLNK ADDING DELETING CHANNELS ADD and DEL not BLNK can be used independently for channel banks 1 2 3 and 4 It is best to do ADD DEL customizing before doing BLNK A channel blanked is blanked in all channel banks AUTO PROGRAM enters the same channels in banks 1 2 3 and 4 Channel allocations in tuning bands AUTO PROGRAM removes any channels previously customized BROADCAST 2 69 with ADD DEL BLNK The channels available on your CABLE CATV HRC or ICC 1 125 antenna cable will be entered and any channels previously entered but not currently available will be deleted PAGE 38 Managing the Channel Banks PLAN YOUR CHANNEL BANKS BY FILLING IN THESE CHARTS or use photocopies Channel Number PAGE 39 Installer Overview Following is the Commercial Mode Operation Setup Operating Installer Menu To set up the controls for the TV you will need to know how to enter the L20V54S Installer menu and make changes to the default values as required If
51. gears CL Sees dp a D PILLOW JACK IN O ve N 12V DC 40mA CONTROL NORMAL he A D oa AUDIOIN VIDEO IN TV PAGE 14 Front Panel Controls Using the front control panel to operate the LCD TV Monitor Power Standby Indicator Glows red in Standby mode Glows green when the TV is turned on Glows orange in Sleep Timer Remote Control Sensor and or Alarm mode TV Operation Press the POWER button to turn the LCD TV Monitor on from standby mode lt 5 Press MENU repeatedly to scroll through menus Note With Installer menu item 11 Key Defeat set to 000 the default setting Menu and TV AV keys are disabled v lt 2 J z 5O c G m gt j o Displays the current channel bank Press again to change banks m a w gt gt Use the CH Channel Up Down button to cycle through the available channels Use the VOL Volume Up Down button to adjust the sound level to your preference On Screen Displays See descriptions on page 18 On screen displays will appear when the feature is active or the function is being used LED Color Action Status RED Power is Off Standby GREEN is flashing Power On sequence is processing GREEN Power is On ORANGE If Power is Off On Timer is set or Alarm is set If Power is On Off Timer is set or Sleep Timer is set PAGE 15 On Scre
52. ic Frequency Control Selects the tuning band There are 4 possible settings for this option 1 CATV 3 IRC 0 Broadcast 2 HRC If some channels were not found by Auto Program select the appropriate Band setting here and add the channels using the Channel List option in the Channel Menu 004 STRT CHANNEL Start Channel If active this function allows you to determine the initial channel number when the L20V54S is turned On This feature is useful for an in house information channel since the L20V54S would always select that channel when it is turned On Setting this to 255 causes the last channel viewed when the L20V54S was turned Off to be the tuned to channel when the L20V54S is turned On again 1 125 ChX 0 Aux 127 Map to Channel 4 255 Last channel 126 Map to Channel 3 005 CHAN LOCK Channel Lock CHAN LOCK is ideal if the system must always be on the same channel Changing channels with Channel Up Down or keypad numbers is impossible Channel Lock is inactive if set to 0 default Generally this feature is used in connection with START CHANNEL Installer item 004 where the start channel may for example be set to 3 or 4 If the start channel is 3 then the L20V54S will remain locked on Channel 3 Note For Items 007 008 and 009 For legacy reasons the scale used is 0 63 The PTC software will translate this to the 0 100 scale used by the TV To translate a TV volume level to the installer me
53. ks The TV has four channel banks where the administrator or installer can store groups of TV channels PLANNING THE CHANNEL BANKS Generally TV channels are grouped into program packages with terms that are proposed to the end user The user then chooses a package Below is an example of how TV channels may be grouped You may plan your packages by using a chart like the one after the following page Remember you can blank a channel for accommodating audio only such as an FM radio station or in house communication Sometimes only one or two channel banks may be needed You may leave any unused bank with the channels entered during Auto Program or you may delete the channels However you may want to leave at least one channel in any unused bank Then if someone selects an unused bank that channel will assure them that the TV is functional Note Some channels from factory testing may be in the channel banks if you have not yet run Auto Program Channel Bank Program package Basic cable channels Extended cable channels Extended with premium channels 4 Other cable service options Grouping is provided as an example only The BLNK blank channel function is global the same channel number is blanked in all channel banks 1 2 3 and 4 oo YW ADDING DELETING CHANNELS A previously prepared programming chart is helpful 1 Run Auto Program in the Setup menu All channels found on yo
54. l Signal Strength Auto Program Searching Channel Label i Channel List A gt Signal Strengt ANALOG34 added gt iia Channel List After the channel search remove unwanted channels Removing unwanted channels Review the channels found you may remove unwanted channels Antenna Press the MENU button Then use the ADJ A button to Q channel Label select the Channel menu then press the OK Enter oe d button Use the ADJ A V button to highlight Channel List then press the OK Enter button Use the ADJ A button to highlight the channel you wish to delete then press the ADJ Right arrow button The right arrow toggles the check mark on and off If the check mark appears next to the channel number the Antenna E channel appears in the channel scan f maoa y ANUE SE ANALOG 16 Press the MENU button repeatedly to remove the menus M ihre DIGITAL 7 1 DIGITAL 11 1 Signal Strength 1e DIGITAL 88 1 66688 If you delete a found channel it isn t gone forever Simply re enter the Channel List menu and re add the OK D channel to show the check mark PAGE 21 Channel Labels Setup Note If you add channel labels to existing channels then re run Auto Program the labels will all be deleted Channel Labels Setup Channel Labels help the user identify the channel or network being viewed In the Setup menu with the Channel Labels
55. l times to remove the menus Analog Mode Analog Captions will display on the screen whether the signal is from an RF channel or external equipment input Note Pressing CC on the remote selects a captions option Press the MENU button and then use the ADJ A V button to highlight the Caption menu Press the OK Enter button Use the Down ADJ arrow to highlight Analog Mode and press the OK Enter button Use the A V lt ADJ buttons to choose CC1 TEXT4 Press the OK Enter button Press the MENU button several times to remove the menus Mini glossary 11 20 PM Sep 11 2006 11 20 PM Sep 11 2006 11 20 PM Sep 11 2006 On Off Analog Mode Digital Mode Digital Font Optio On Off Analog Mode Me On Off Analog Mode Digital Mode Digital Font Optio ono Analog Mode oer Digital Mode CC3 Digital Font Optio cc4 TEXT1 TEXT2 TEXT3 TEXT4 CAPTIONS The term for the words that scroll across the bottom of the TV screen usually the audio portion of the program provided for the hearing impaired The term for the words that appear in a large black frame and almost cover the entire screen usually messages provided by the broadcaster PAGE 31 Caption Menu Continued Digital Captions Mode On Off On gt Digital Font Option Digital Captions only appear on digital channels tune in a digital channel that is actually broadcasting digital captions Note P
56. ller menu settings e Software problem Adjust Installer menu settings as required Remove TV power cord for 15 seconds Remote Control e Remote not in TV mode e Not aimed at IR remote sensor e Remote too far from IR sensor Remote doesn t work e IR path to TV s receiver obstructed e Weak batteries e Wrong battery polarity e Too much light in room e Wrong Installer remote control e Incorrect Bed 1 2 setting Use Mode key to select TV puts remote into L20V54S mode Point remote at TV s IR receiver on TV Move remote closer to TV s IR receiver or darken room Remove obstructions Replace batteries Check that and match in battery compartment Dim room light Requires compatible Installer remote contact your LG dealer Set correct Bed 1 2 setting Picture Reception e Audio muted e Broadcast problem Normal picture poor or no sound Press MUTE or use Volume Up key to increase sound level Try a different channel Broadcast Tuning Mode Digital Channel OSD e Item 103 set to 1 physical channels tuning No Information available display Set Item 103 to 0 for information to be added to virtual channel tuning digital OSD Note For other problems not caused by the L20V54S refer to other devices operating guide PAGE 55 Reference Cloning Procedure Troubleshooting Warning Do not use LT2002 while a LodgeNet PPV card is in
57. necessary familiarize yourself with the L20V54S Installer menu and how to make and save changes in the menu Optional Installer Remote You will need an Installer remote control similar to the one shown to the right The TV s clonable features need to be set up before 2 5 5 Menu is done This is a critical step If the Master TV display panel s clonable features like Clock Set adding channel icons and channel labels etc are not done properly then the cloned L20V54S TVs will all have problems For example do not do 2 5 5 Menu more than once or the TV setup will become corrupted If you need to start the procedure over then begin by setting installer item 117 to 001 and pressing Enter to reset the TV to default values in the installer menu You can do 2 5 4 Menu mode more than once but this mode is limited to only editing channel icons and channel labels Refer to the appropriate section in the Manual for other TV features Picture Sound etc LT2002 Clone Programmer As the cloning procedure is being performed specific steps need to be done at the indicated times to achieve the desired O result Be sure to do each cloning task as indicated Z If a procedure or step is left out or not MPI performed correctly then the TV a rae setup will be wrong and cloning may not battery low E ete work At each step pay attention to assure ame ll the TV screen shows the proper message s E when cloning If the message indic
58. nnel label icons added enter the Installer menu Once in the Installer menu press 2 5 5 and MENU on the remote This transfers the TV setup to the internal controller box Note Only do 2 5 5 MENU once or TV setup may be corrupted TV scans available channels and exits menu when transfer to controller is complete 5 Perform Adding Custom Channel Labels 2 5 4 Menu Mode Enter Installer menu press 2 5 4 and Menu Add your own custom labels to the channel on screen displays See page 53 To remove menu press MENU Note 2 5 4 MENU can be performed more than once Verify TV Setup At this point verify that the channel lineup channel icons and custom labels are correct Make sure the TV features are set per your requirements Set item 028 CH OVERIDE to 000 to lock the channel scan After the preceding has been completed the Master TV setup is ready to be copied to the LT2002 Clone Programmer see next page L20V54S PTC INSTALLER MENU 000 INSTALLER SEQ UPN 000 000 000 000 FPGA 09F1 PTC V1 00 000 CPU V1 01 00 L20V54S Installer Menu 117 FACT DEFAULT 00X 003 BAND AFC 00X 0172 CH OVERIDE 001 073 CH NOT AVBLE 001 L20V54S Installer Menu Items DIGITAL 19 3 ANALOG 2 MONO STEREO SAP WXYZ MONO WXYZ Custom Channel Label WXYZ created in 2 5 4 Menu Add Channel Label Mode 028 CH OVERIDE 000 After TV setup has been verified set item 0
59. nu value use the following formula Installer Value TV Value x 63 100 Enter only the whole number disregard fractions 007 STRT VOLUME Start Volume This function allows the Installer to determine the initial volume level setting when the L20V54S is turned On This feature is useful for an in house information channel since the L20V54S would always select that volume level when it is turned On The range of values are 0 63 255 If 255 is selected the current volume level will be retained in memory when the L20V54S is turned Off at turn On the volume level will be automatically set at the previous or last level 008 MIN VOLUME Minimum Volume This function determines the minimum volume level allowable with the VOLUME VOL Up Down control In this way for example someone cannot set the volume too low to hear The value range is from 0 to 63 change values with ADJ Left Right arrow The factory default is 0 which provides the full range of volume control if item 009 MAX VOLUME is also set to 63 It may be best to set the same value on every L20V54S Note The minimum volume level cannot have a value setting higher than the MAX VOLUME level described below 009 MAX VOLUME Maximum Volume This function determines the maximum volume level allowable with the VOLUME VOL Up Down controls In this way for example someone can not set the volume level high enough to disturb others Continued on next page
60. o Auto Program more than once Channel List Clock etc Note 2 5 4 MENU can be done more than once Virtual and Physical 2 5 5 MENU not performed After Auto Program and Channel List etc press 2 5 5 MENU to transfer channels appear in channels and TV setup to internal TV controller Afterward only Physical or channel scan w Channel only Virtual channels will appear in digital channel scan analog channel Up Down scan will be normal Note Be sure to set item 028 Ch Overide to 000 Can not direct enter Channel not included in After 2 5 5 MENU only channels included in TV controller will appear channel number channel scan in TV controller If channel is available redo channel scan If it is not available it will not appear on the TV screen PAGE 54 Troubleshooting Some quick and easy tips to resolving problems Symptoms Possible Cause s Possible Solution s See Page s Power No Power See troubleshooting flow chart Display Panel Picture No Picture e Display panel is turned off e Antenna Cable not connected e Connections incorrect e M P I not connected e Encrypted program e Wrong tuning band Turn TV on Power failure Connect Antenna Cable signal source to L20V54S Check connections on L20V54S If applicable connect M P I cable to M P I device Try another channel Adjust Installer menu settings Erratic Operation Installer menu setup e Wrong Insta
61. option highlighted use the ADJ Left Right arrow to scroll through the available channel labels such as A amp E AMC ESPN HBO etc These are a series of preset labels from which you can choose the more common networks Use any of these to label the channels in the TV s memory Operating the Channel Label Menu Press the MENU button and then use the ADJ amp button to select the Channel menu Press the OK Enter button Use the ADJ A button to highlight Channel Labels then press the OK Enter button This action displays the Channel Labels menu Use Channel Up Down to select channels and the Up Down Left Right ADJ arrow buttons to navigate the labels menu When the label is highlighted you want for the channel shown in the screen press OK Enter to add the label to the channel Select the next channel to label with Channel Up Down or if finished channel labeling press Menu repeatedly to remove menus PAGE 22 Clock Setup Manual Time Settings ime Use the A V lt P ADJ buttons to set the year month day oa hours and minutes if I Menu Transparency Press the MENU button and then use the ADJ A button to highlight the Setup menu Press the OK Enter button to highlight Time Press the OK Enter button to highlight Clock Manual or Auto will appear on the menu next to clock If manual is selected on the menu use the Down arrow to highlight Manual and press the OK Enter
62. play Press the ALARM Set a time for the TV to turn itself on V Chip Press the CC Move to the V Chip menu oe SAP Display Selects MTS sound Mono Stereo and SAP in analog mode Change the audio language in DTV mode Guide Display Press the GUIDE to view DTV program information Kil DIGITAL 84 1 No Time Information Au No Title NA Dolby Digital E 1920 1080 60Hz Korean g NA INFO Press the INFO Check the current program information PAGE 17 User Remote Control Key Functions A brief list of the keys on the optional patient remote control and what they do CC Closed Captioning Press to access closed captions POWER Turns TV On or Off TV FM Down arrow for navigating menus VOLUME Decreases increases sound level NUMBER KEYPAD Selects channels directly and enters numerical values for some options BUTTON When selecting a digital broadcast channel key in the Main channel number followed by the gt gt then the sub channel number Analog channels do not contain a sub channel number TIMER Press repeatedly to select a preset time to automatically shut the TV off MENU Press to display the main on screen menu FLASHBK Flashback Returns to the previous channel viewed MUTE Turns sound Off and On while the picture remains CHANNEL Tunes to next available channel ENTER Press to view the Channel Time display or to remove any on s
63. r Temperature press the OK Enter button Use the lt ADJ buttons to choose Warm Cool or Normal When finished press the OK Enter button Press the MENU button several times to remove the menus Screen Format Adjustments The user can choose preset formats for the picture Press the MENU button and then use the ADJ A YW button to highlight the Picture menu Press the OK Enter button Use the Up Down arrow button to choose Screen Format press the OK Enter button Use the lt ADJ buttons to choose a preset screen format Set By Program 16 9 or 4 3 When finished press the OK Enter button Press the MENU button several times to remove the menus Sep 11 2006 Mode Color Temperature Screen Format 4 3 Noise Reduction Film Mode Options Turn Film Mode On to view movies with optimum preset picture settings The user can watch movies with a more realistic picture on analog channels Press the MENU button and then use the ADJ A V button to highlight the Picture menu Mode gt Color Temperature Screen Format Noise Reduction Film Mode Press the OK Enter button Use the Up Down arrow button to choose Film Mode press the OK Enter button 11 20 PM Sep 11 2006 4 Use the Left Right ADJ buttons to choose on or off When finished press the OK Enter button 5 Press the MENU button several times to remove the menus PAGE 36 Managing the Channel Ban
64. ressing CC on the remote selects a captions option Press the MENU button and then use the ADJ A V button to highlight the Caption menu Press the OK Enter button Use the Down ADJ arrow to highlight Digital Mode and press the OK Enter button Sane Digital Mode Service2 SII Digital Font Opti SEIREESE Use the A lt gt ADJ buttons to choose Service 1 5 Serviced Service 6 Service5 Service6 Press the OK Enter button Press the MENU button several times to remove the menus Digital Font Options On Off On gt Analog Mode Mode Digital Font Option Press the MENU button and then use the ADJ A YW button to highlight the Caption menu Press the OK Enter button Use the Down ADJ arrow to highlight Digital Font Options and press the OK Enter button Use the A V lt gt ADJ buttons to customize each option Font Size Font Style Foreground Color etc a Fort Size Default Foreground Color When finished press the MENU button several times to remove the menus Note If the digital options custom settings are to be cloned all menu options should be set to any option other than Default If Default is left set for any one option then all the options will be reset to default after cloning PAGE 32 11 20 PM Sep 11 2006 Background Color Edge Color Foreground Opacity Background Opacity Edge Style NY Sound Menu Set up the audio options for the end
65. ries TV MA Mature audiences only This program may contain mature themes profane language graphic violence and explicit sexual content TV 14 Parents strongly cautioned This program may contain sophisticated themes sexual content strong language and more intense violence 11 20 PM TV PG Sep 11 2006 Parental guidance suggested The program may contain infrequent coarse language limited violence some suggestive sexual dialog and situations TV G General audience This contains little or no violence no strong language Allow All Block All and little or no sexual dialog or situations Pec TV Y7 Setu TVPG Raning ooooo Directed for older children Themes and elements in this program may include mild physical or comedic violence or may frighten children under the age of seven All children The themes and elements in this program are specifically Sep 11 2006 designed for a very young audience including children from ages two six TV FCC Content Sub Categories V Violence S Sexual content L Offensive language D Dialog sexual innuendo FV Fantasy or cartoon violence PAGE 28 V Chip Continued MPAA Ratings Restricting movies by their rating ime a onio Press the MENU button and then use the ADJ A button y to highlight the Setup menu X Menu Transparency SetiD 96 Press the OK Enter button Use the Down ADJ arrow to highlight V Chip and press the OK Enter
66. roubleshooting section to resolve problems menus e Make sure that the batteries in the Clone programmer are fresh Turn to the next page to continue Cloning Setup e If batteries are removed the Clone Clock time will be lost Decide if you want to set the time from the Clone programmer or copy the time to the Clone programmer from a compatible TV which has the clock set to the current time PAGE 42 Clone Programmer Learning Setup Learning the Master TV Setup Instructions for the Clone Programmer to Learn the Master L20V54S Setup Use MPI Cable to Connect LT2002 Clone Programmer to Master L20V54S MPI Port If there is a good connection THE CLONE HAS CONTROL OF TV message will appear Press any key on the Installer remote Learn Setup from Master L20V54S Press 1 to select the LEARN FROM TV option then press ON OFF POWER or ENTER to go to the Memory Bank Selection Menu Pick the Memory Bank you want to store the master L20V54S s setup in by pressing either Channel key repeatedly to choose Memory 1 2 or 3 If you choose a Memory Bank that has a master device s setup programmed into it that setup will be overwritten by the new master L20V54S s setup Once the Clone memory bank is selected press ON OFF POWER or ENTER The Clone memory bank you have selected will be shown Press ON OFF or POWER to begin copying the master L20V54S s setup Set the Clock Optional Set the time on a Master
67. s to restrict both analog and digital programming e Aux Channel allows the guest to select the Audio Video inputs Use the A V jacks on the back of the TV as a source BUTTON When selecting a digital broadcast channel key in the Main channel number followed by the gt gt then the sub channel number Analog channels do not contain a sub channel number TIMER Press repeatedly to select a preset time to automatically shut the TV off MENU Press to display the main on screen menu BANK PREVIEW GUIDE TIMER MENU ALARM ADJ lt ADJV ADJP BED1 Gam BED2 Optional Installer Remote Control Part Number 31400SKZ003AR6 POWER Turns TV On or Off GUIDE Use to view DTV program information cc Press to activate English subtitles INFO Press to display current program information VOLUME CHANNEL OK Enter Increase or decrease the volume Change channels Select on screen menu items and change menu values NUMBER BUTTONS Use for direct channel entry FLASHBK FLASHBACK Use to return to the last channel viewed ALARM Use to go to the Alarm menu Set a time for the TV to turn itself on ADJ A V lt gt User ADJ adjust Up Down menu arrows Left Right to change the selected option BED 1 BED 2 See Note Below Determines the code set transmitted Bed 1 or Bed 2 Switch setting must correspond to item 27 HOSPITAL MODE setting in the TV s Installer Menu Note Bed 1
68. ss to Auto Program Channel Labels and Channel List options in the Channel Menu Set other particular installer items that affect your TV programming network See pages 46 51 After all required installer menu item settings have been adjusted press ENTER on the remote to remove Installer Menu 2 Set Up TV Features See Picture Sound Setup menus etc See TV Clonable options list on page 52 Installer Note Some TV features will have to be set up after running Auto Program An example is Digital Font options This feature is not available until digital channels are found in the channel scan Set up Digital Font options after Auto Program finds a digital channel with digital captions Do this before running 2 5 5 Menu 3 Run Auto Program Search for all available channels Go to the Channel menu and access the Auto Program option follow on screen instructions a Edit Channel Scan In the Channel Menu access the Channel List menu e Delete channels per your system requirements do you want to delete any free channels so the guest cannot access them e Add familiar Channel Icons like ABC CBS NBC etc to the channel on screen display Add identifiable labels for the end user to readily know what common networks are available In the Channel menu select the Channel Label option follow instructions on the bottom of the screen 4 Transfer TV Setup to Controller Box 2 5 5 Menu After the TV channel scan has been edited and cha
69. st and TV turns off 014 STRT CH IN SM Start Channel in Scan Mode When set to 1 installs TV On Off event below the start channelat TV turn on 015 SLEEP TIMER If set to 1 the SLEEP TIMER feature may be used If set to 0 the Sleep Timer is not available 016 EN TIMER Enable On Off Timers If set to 1 Timer function is available to user Set to 0 to disable On Off Timer functions Clock must be set in order to use Timers 017 ALARM Gives the installer the option of making the Alarm function available to the end user If set to 1 Alarm function is available to end user Set to 0 to disable the Alarm function Note Clock must be set before the Alarm function will work Installer should leave item 20 FEATURE LEVEL set to 1 default PAGE 48 020 FEATURE LEVEL Default set to ZEN 1 for Zenith IR remote control opera tion Set 0 P LBL for Zenith Private Label IR remote con trol operation Warning Do not set to 0 or remote will not control TV 021 V CHIP Parental Control Set to 1 to activate V Chip Parental Control have it available to end user to filter and control or otherwise restrict programming content that can appear Set to 0 to turn V Chip feature Off not available to user no programming restrictions can be set 022 MAX BLK HRS Maximum Block Hours Sets hours from 0 to 99 for the maximum V Chip Parental Control block hours Default setting is for 12 blocking hours 023 CAPTI
70. stalled in TV or clone programmer will be damaged Note The LT2002 programmer is designed to be used with TVs Reset Clone After Static Shock con taining the 221 01006 and later processors Use with earlier After replacing exhausted batteries or if the programmer behaves TV sets may give unpredictable results Processors used before the strangely after a static shock activate the internal reset switch and 221 01006 04 have a limited screen display capability They restore normal operation cannot display entire screens as shown in the quick setup After a reset check the real time clock setting It may be necessary to instructions accompanying the LT2002 clone programmer Use the reset the Clone Programmer clock from a TV containing the correct printed menu illustrations on the quick setup sheet supplied with time the Clone as an aid to making your programming choices Although the menus are not all displayed the clone functions all operate normally Clone Programmer Troubleshooting Clone Programmer Cloning Notes While clone is copying or transferring a master setup do not touch or otherwise disturb clone or connections between clone and TV Cloning a master TV setup should take at least 45 seconds Transferring the master TV setup to the target TV should take at least 45 seconds Monitor LED on clone to assure that the blinking heartbeat pattern is present throughout clone operations After cloning be sure to disconnect power from the targ
71. t L20V54S not reset Disconnect newly cloned unit from power for 5 seconds e After cloning operations are complete just unplug the LT2002 from the L20V54S e If the L20V54S does not display a picture on the TV blank screen after a few seconds just change channels PAGE 56 Clone Troubleshooting Flow Chart Controller Quick Plu eee Connected to into AS Press POWER or ON OFF DTV Board AC Power Blinking 2 2 Power Outlet key on TV 1 Bad TV Press POWER or ON OFF or VOLUME UP DOWN or MUTE key on Remote 1 Bad PPV Board 2 Bad DTV Board Respond 1 Bad TV Cycle the power by removing 9 and re connecting the AC i power cord Observe the POWER LED and TV screen as soon as AC power is re applied LED Turn On Momentarily Did TV Turn On Check to see if TV Momentarily is in Commercial Mode See Commercial Mode Check chart PAGE 57 TV Operation Check Press the On Off key on the front panel The On Off key is always operational Did you get a response 2 Go to Installer menu by pressing MENU until the TV stops responding Did TV stop responding or continue TV is in Commercial responding Mode to respond Continued to respond TV is not in Commercial Mode Call Technical Support for Assistance PAGE 58 Glossary of Terms A list of definitions for some of the words found in this guide 75 OHM RF CABLE The wire
72. t into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Marketed and Distributed in the United States by LG Electronics U S A Inc 2000 Millbrook Drive Lincolnshire IL 60069 CAUTION Do not attempt to modify this product in any way without written authorization from Zenith Electronics Corporation Unauthorized modification could void the user s authority to operate this product COMPLIANCE The responsible party for this product s compliance is LG Electronics U S A Inc 2000 Millbrook Drive Lincolnshire IL 60069 USA Phone 1 847 941 8000 WARNING Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids such as vases shall not be placed on the apparatus CAUTION THESE SERVICING INSTRUCTIONS ARE FOR USE BY QUALIFIED SERVICE PERSONNEL ONLY TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE OPERATING INSTRUCTIONS UNLESS YOU ARE QUALIFIED TO DO SO CAUTION When used outside of the U S it may be used HAR cord with fitting of an approved agency is employed When used outside of U S other power supply cords may be used if the cord is approved by the local regulating agency CAUTION 1 Do not put this product next to the patient s bed where it can be reached by the patient 2 Install product in such a way that patients will not be
73. t set to 0 001 POWER MANAGE 0 7 Sets number of hours of no activity before auto shut Off 002 AC ON 0 1 Set to 1 to enable auto turn On at power up 003 BAND AFC 0 3 Selects Tuning Band 0 Broadcast 1 CATV 2 HRC 3 IRC 004 STRT CHANNEL 0 127 255 Channel at turn on Set 255 to return to last channel before power Off 005 CHAN LOCK 0 1 If set to 1 cannot tune from current channel 007 STRT VOLUME 0 63 255 Sets Volume level at TV turn on Set 255 to retain last volume level MIN VOLUME 0 63 Sets minimum allowable volume setting MAX VOLUME 0 63 MUTE DISABLE 0 1 KEY DEFEAT 0 1 IR BANKS EN 0 1 SCAN MODE 0 1 STRT CH IN SM 0 1 SLEEP TIMER 0 1 EN TIMER 0 1 ALARM 0 1 FEATURE LEVEL 0 1 Zen 1 Leave default set 1 1 Zen 1 V CHIP 0 1 Set to 1 to enable V Chip functions MAX BLK HRS 0 99 Sets number of V Chip Parental Control blocking hours CAPTION LOCK 0 1 Set to 1 to retain caption setting at power Off FUNCTION PRE 0 3 Controls channel preview in Pay Per View function HOSPITAL MODE 0 2 Leave default set to 2 CH OVERIDE 0 1 If set to 0 limits direct access to favorite channels OLD OCV 0 1 Set to 1 to change M P I operation to OCV ACK MASK 0 1 If set to 1 changes M P I for some OCV boxes POLL RATE 20 169 Selects poll rate for M P I TIMING PULSE 186 227 Sets baud rate for M P I a w Sets maximum allowable volume setting Set to 1 to disable mute function Set to 1 to disable menu na
74. tem 102 ATSC BAND is set to 1 CATV 2 HRC or 3 IRC Then 103 ATSC TUNE MODE above always resets itself to Physical 1 regardless of what value appears for item 103 on the Installer menu 104 START MINOR CHANNEL Sets XX XX minor starting channel at power up O NTSC If not 0 number selected is the Minor start channel number 106 ASP RATIO LOCK Aspect Ratio Lock Set to 1 to retain previous aspect ratio with power Off Set to 0 to retain default aspect ratio with power Off See item 96 Default Aspect Ratio above Reference TV Features Menus that can be Cloned 107 BANNER SELECT Not applicable 116 VIDEO MUTE EN Video Mute Enable Set to 0 for normal Set to 1 for blank 117 FACT DEFAULT Factory Default Set to 0 for normal Set to 1 to load default settings for all installer menu items WARNING Setting this to 1 will reload the factory defaults and clear the channel list including erasing any assigned Channel Icons and Labels Clonable Menu Features Sound Mode Mode Contrast Treble Brightness Bass Channel Picture Auto Program Active channels found with the channel search Channel Labels Color Channel List Sharpness Fine Tune Tint Color Temperature Screen Format Film Mode Balance Auto Volume Multi Track Internal Speaker Setup Caption Time On Off Clock Analog Mode Auto Off Digital Mode V Chip Digital Font Option TVPG Rating MPAA Rating Menu Language SET ID Note For Digit
75. tential hazard to the user Antenna Hookup Connect an off air antenna to the LCD TV Monitor Locate the Antenna Cable jack on the back of the LCD TV Monitor Connect the antenna wire Flat or Round a ee that runs from the wall to this jack aD 0 is according to one of the diagrams shown to the right Connections Panel After all connections are complete plug in Flat Wire the TV The LCD TV Monitor is designed to ent aim operate on AC power 300 75 ohm Adapter SPEAKER SWITCH If the antenna is a 75 ohm RF cable then no adapters are required er ie see CO ea eB O A 300 to 75 ohm adapter is not included with _ the Zenith LCD TV Monitor Connections Panel i RF Coaxial Wire _ cS 75 ohm Mini glossary 75 OHM RF CABLE The wire that comes from an off air antenna or cable service provider Each end looks like a hex shaped nut with a wire sticking through the middle and it screws onto the threaded jack on the back of the TV 300 TO 75 OHM A small device that connects a two wire 300 ohm antenna to a 75 ohm RF jack They are usually about an inch long with two screws ADAPTER on one end and a round opening with a wire sticking out on the other end Cable Service Hookup Connect cable service to the LCD TV Monitor Locate the Antenna Cable jack on the back of the TV Connect the cable wire to the Antenna Cable jack according to one ene of the diagrams to the right Wall Jack RS 232C FUTURE PILL
76. tes analog and digital interfaces with a single connector COMPOSITE VIDEO Typical video jack uses one wire for transporting three color video signals DELETED Lets you remove channels from the list that the end user can scroll through using CH Channel Up Down HDMI High definition multimedia interface HDTV High definition television Refers to television signals that have higher resolution than ordinary analog TV signals HDSTB High definition set top box Refers to a tuner device that receives high definition television signals which have higher resolution than ordinary analog TV signals INPUT Refers to the input jack that receives a signal from a TV VCR DVD Player or other Audio Video device JACK An input or output connector on the back of a TV VCR DVD Player or other Audio Video device MONO SOUND Mono monaural sound is one channel of sound On more than one speaker all the speakers play the same audio OUTPUT Refers to the output jack that sends a signal out of a VCR DVD or other A V device PHYSICAL CHANNEL NUMBER Actual digital major dashed minor channel number that a station is broadcasting on RGB Red Green Blue Connection input or output port available for producing a video image using three separate colors Red Green and Blue 2ND AUDIO PROGRAMMING SAP Second Audio Programming SAP is another separate audio channel available with some programming Choosing SAP often refers
77. to listening to audio in another language such as Spanish or French SIGNAL Picture and sound traveling through a cable or over the air to the TV STEREO SOUND Stereo Stereophonic sound refers to audio that s divided into right and left sides TUNER Device that picks up the broadcast signal and turns it into picture and sound VIRTUAL CHANNEL NUMBER The arbitrarily assigned digital dashed minor channel number that a station is broadcasting on PAGE 59 Installer Quick Setup Guide Quick Setup Guide for Integrated Master TVs See table of contents for more information L20V54S PTC INSTALLER MENU 000 INSTALLER SEQ 000 FPGA 09F1 CPU V1 01 00 UPN 000 000 000 000 PTC V1 00 000 FACT DEFAULT 117 00X 003 BAND AFC 00X 28 001 0 CH OVERIDE VIDEO SPEAKER SWITCH om RS 232C UPDATE RS 232C FUTURE paon a lies SELECT USE SPEAKER SPEAKER P o oa 0 TEER ale ain AUDIOIN VIDEO IN DTV Antenna AC Power Wall Jack RF Coaxial Wire 750hm Setup Instructions for Making a Master TV 1 Connect TV to signal source connect power cord and turn TV power on 2 Enter the TV installer menu Note If this is not a new setup set Installer item 117 to 001 and press Enter to reset TV to default condition e Set Tuning Band Set Installer menu item 003 BAND AFC to CATV 001 Broadcast 000 etc e If necessary set Installer menu item 028 CH OVERIDE to 001 In addition set any other install
78. to highlight Time Press the OK Enter button to highlight Clock Manual or Auto will appear on the menu next to clock Select Auto on the submenu with the Down arrow and press the OK Enter button cere Use the ADJ Up Down Left Right arrows to highlight and S TimeZone set the Time Zone for your local area lt i Use the ADJ lt gt button to select the time zone then Sep 11 2006 press the ENTER button ais When finished press Menu repeatedly to remove the menus PAGE 25 Menu Language Choose a language for the on screen menus Press the MENU button and then use the ADJ A V button to highlight the Setup menu Press the OK Enter button Use the Down ADJ arrow to highlight Menu Language and press the OK Enter button Use the ADJ Up Down Left Right arrows to highlight and set the Menu Language English Spanish or French Press the MENU repeatedly to remove the menus PAGE 26 11 20 PM Sep 11 2006 Time gt Menu Language Language Menu Transparency Transparency Menu Language J English Menu Transparency Espa ol EEWO Entering a PIN Password This option sets up or changes the password for blocking program ratings o o oN Press the MENU button and then use the ADJ A V button to highlight the Setup menu Press the OK Enter button Use the Down ADJ arrow to highlight V Chip and press the OK Enter button If a password has been entere
79. ts a time the TV will turn off Selects MTS sound Mono Stereo and SAP in analog mode Change the audio language in DTV mode Selects Caption Text options Set a time for the TV to turn itself on View DTV program information Displays the available TV channels and guest s Parental Control menu Shows program details Title Broadcast Time ionat Format Signal Strength CC V Chip Language Sound Format Time Date Channel Icon Channel Label INSTALLER MENUS 41 Makes adjustments to the TV s operational features Other Menus amp On Screen Displays Use the remote keys indicated below to access these menus and displays In this manual the OSD On Screen Displays shown may be different The following are just generic examples to familiarize you with the TVs options eo Volume Display Press VOLUME Shows currently selected sound setting CAPTION Caption Display Press the CC Turns selected option on or off See Closed Captions page to select options Antenna eee Add Program hannel Label MUU ANALOG 16 Channel List DIGITALA eT DIGITAL 11 1 Signal Strength WR c a DIGITAL 88 1 v AV Move D COCE Ee Channel Preview Press the CH PREVIEW Displays available TV channels Sleep Timer Menu Press TIMER Sets a time to automatically turn the TV off and shows remaining time before TV shutoff Current Time 11 17 AM 2 M n Lor lt gt Move a v Adjust OK Bit Alarm Dis
80. ur cable antenna will be entered in Channel Banks 1 2 3 and 4 Note Be advised that running Auto Program overwrites any custom channel setups removes Blanked Deleted Select a channel bank with an installer remote press SOURCE BANK and repeat CHANNEL BANK and BANK number will be displayed CHANNEL BANK BANK 1 Channel Bank Number Display Use the ADD DEL BLNK option also in the Setup menu to customize your program package You may delete channels or add some that have not been entered You can also Blank a channel for accommodating an audio only program source or in house communication The ADD DEL BLNK option on page 15 has more details Note The Blank Channel feature is global A channel will be blanked in all channel banks 4 Repeat steps 2 and 3 to program another channel bank Inactive TV Display Channel Bank 4 The TV can be set up to be inactive which would require an attendant using an installer remote to change to a billable active channel bank selection Bank 1 2 or 3 Note For institution control of patient accessible programming channels in Bank 4 need to be removed INACTIVE TV PLEASE CALL ATTENDANT PAGE 37 Managing the Channel Banks Examples of typical channel banks chars filled in Figure 1 Typical channel banks after running Auto Program A E rr rrre 1 Rime ee SARE st A AE EEE AE A A AJAJAJA ARE te A Active Channel was found durin
81. utton several times to remove the menus lt Dolby Digital gt OODOLEY This product is under license of Dolby Laboratories DIGITA L The Dolby or D symbol is a trademark of Dolby Laboratories PAGE 33 Sound Menu Continued Digital Audio Language Settings You can set digital audio language Press the MENU button and then use the ADJ A V button to highlight the Sound menu Press the OK Enter button Use the Up Down arrow button to highlight Multi Track press the OK Enter button Use the 4 gt ADJ buttons to choose English Spanish or French press the OK Enter button Press the MENU button several times to remove the menus Using External Speakers Set the internal speaker to Off to listen to the TV through an external audio system the TV sound will not be heard Press the MENU button and then use the ADJ A V button to highlight the Sound menu Press the OK Enter button Use the Up Down arrow button to highlight Internal Speaker press the OK Enter button Use the 4 gt ADJ buttons to choose English On or Off press the OK Enter button Press the MENU button several times to remove the menus PAGE 34 Sep 11 2006 11 20 PM Sep 11 2006 Balance Auto Volume Multi Track English Internal Speaker Mode Balance Auto Volume Internal Speaker On Picture Menu Picture Mode Setup Set the picture mode to the program content e g Dyn
82. vigation keys on display panel Set to 1 enables TV to respond to IR code Typically used for Hospitals puts On Off and FM in Ch Up Down sequence Set to 1 to put TV on off below start channel number Set to 1 to enable Sleep Timer Set to 1 to enable On Off Timers Set to 1 to enable Alarm ojojojojojojojo sijoja AJ wl njej o ej ej ejejej ojejlo e o PAGE 45 Installer Menu Installer Menu Items 035 through 117 Menu Item Function Value Range Default Value Brief Description of Function and Comments 035 COMPPORT EN 0 1 Set to 1 to enable HDMI Set to 0 to disable 039 REAR AUX EN 0 1 Set to 1 to enable display panel Video 1 input jack STRT AUX SRCE 1 7 255 255 Sets the starting AUX source AUX STATUS 0 Set to 1 for M P I AUX source to be reported as a channel number instead of Channel 0 DIS CH TIME 0 Set to 1 to disable Channel Time display EN CH T COL 0 Set to 1 to enable custom color for the Channel Time display FOR CH TIME 0 7 Chooses custom foreground color for the Channel Time display BCK CH TIME CH NOT AVBLE 0 7 0 Chooses custom background color for the Channel Time display If set to 1 and channel override is 0 NOT AVAILABLE message is displayed when
83. wer ee Round or Flat wire 300 ohm VCR Back Panel 000 VCR Back 300 750hm Adapter 1 D mo wien OC Video L Audio R H Connections Panel SPEAKER SWITCH TVED RS 2320 UPDATE RS 232C FUTURE PILLOW CE NORMAL ose SELECT USE SPEAKER SPEAKER PILLOW JACK IN p q mall q 12V DC 40mA s CONTROL NORMAL kene AUDIO IN 5 VIDEO IN Tv PAGE 11 Cable Service with VCR Hookup Connect cable service and a VCR to the LCD TV Monitor Locate the Antenna Cable jack on the back of the VCR Connect the cable service wire to the VCR Connect other wires according to the diagram to the right After all connections are complete plug in the TV The LCD TV Monitor is designed to operate on AC power For cable box operation leave the VCR and the television tuned to channel three or four and use the cable box to change channels lj Cable TV Cable TV Wall Jack Wall Jack VCR Back Out output switch OO uae er y VCR AV Panel output D mo switch 2 Video L Audio R Cable Box Connections Panel SPEAKER SWITCH eg BES RS 232C UPDATE RS 232C FUTURE PILLOW CE NORMAL SELECT USE SPEAKER SPEAKER PILLOW JACK IN GP o 92 9 QD ein CONTROL NORMAL AUDJO IN VIDEO IN DTV a ANTENNA CABLE PAGE 12 Pillow Speaker Hook Up Connect a pillow speaker to the LCD TV Monitor Locate the Pillow

Zenith L20V54S User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents