Home

Zanussi ZWT 10120 User's Manual

image

Contents

1. gt Warnings A These warnings are for the safety of you and others around you Please read these points carefully before installing and using your ap pliance Thank you for your atten tion Keep this user manual with your ap pliance If the appliance is sold or gi ven to another person please make sure this user manual is included This way the new user will have the relevant operating instructions and warnings General safety e Do not modify or attempt to modify this appliance This would put your self in danger e Ensure that all coins safety pins brooches screws etc have been removed before starting a washing programme If left in washing they can seriously damage the appliance e Use the amount of detergent recom mended in the paragraph Using the right amount of detergent e Put small items together socks belts etc in a small linen bag or pillow case e Unplug and close inlet hose tap after using appliance e Always disconnect the power supply from the appliance before cleaning or maintenance e Do not machine wash clothes with ribbing unfinished or torn material warnings 5 Installation e Unpack or ask for the appliance to be unpacked immediately upon arri val Check the outside of the appliance is not damaged in any way Put any complaints you may have in writing on your copy of the delivery receipt e The appliance must be untied before connecting to power supply or us
2. e the Drain programme or Night Silence Plus option have been selected e the height of the drainage U piece is unsuitable e too much detergent has caused foam to over flow e the detergent washing e the drainage U piece isn t attached correctly e the drainage filter hasn t been put back in place e the water inlet hose is leaking is unsuitable for machine 18 operating problems Problems Causes Wash is unsatisfactory e the detergent is unsuitable for machine washing e there is too much washing in the drum e the wash cycle is unsuitable e there isn t enough detergent the wash cycle is much too e the water inlet filters are dirty long e the power or water supply has been cut off e the motor overheating detector has been acti vated e the water inlet temperature is lower than usual e the foam detection security system has been activated too much detergent and the washing machine has begun draining the foam e the out of balance detector has been activated an extra phase has been added to distribute washing more evenly in the drum The lid doesn t open at the e the immediate opening light is not lit end of the cycle e the temperature inside the drum is too high e the lid unlocks 1 2 minutes after the end of the cycle The p Start Pause e the lid isn t closed properly pushbutton flashes red operating problems 19 Problems Causes Start
3. Pause the water inlet tap is closed ee flashes the water supply has been cut off eda Depending on model On some models the audible signals can sound After solving any problems press the Start Pause pushbutton to restart the interrupted programme 20 technical specifications installation Technical specifications DIMENSIONS Height Width Depth LINE VOLTAGE FREQUENCY POWER CONSUMPTION WATER PRESSURE Minimum Maximum Connection to water supply 850 mm 400 mm 600 mm 230V 50 HZ 2300 W 0 05 MPa 0 5 bar 0 8 MPa 8 bar Type 20x27 C This appliance conforms to the CEE 89 336 directive concerning the limi ting of radio electric interference and the CEE 73 23 directive concerning electrical safety Installation A Remove all protective packaging for transit before using for the first time Keep in case needed for future transit Transporting a non secured appliance may damage internal components and cause leakages and malfunctions The appliance can also be damaged through physical contact Unpackin technical specifications installation 21 To install your washing machine at the same level as Surrounding furniture pro ceed as follows Water supply Install the supplied water inlet hose at the rear of your washing machine by proceeding as follows Do not reuse an old hose Open the water inlet tap Check there are no leaks The w
4. again the lights go out If one of the op tions is not compatible with the selected programme the Start Pause pushbut ton flashes red Super Quick option The washing time will be reduced depending on the programme selected Eco option This option allows you to choose a lower temperature programme which is as ef fective as a higher temperature wash programme Prewash option The appliance runs a prewash at 30 C max The prewash finishes with a short spin cycle for cotton or synthetic 10 How to run a wash cycle programmes and with an empty cycle for delicates programmes Extra rinse option The washing machine will add one or more rinses during the cycle This option is recommended for people with sensitive skin and in soft water areas Temporary Press the Extra rinse pushbutton The option is only active for the selected pro gramme Permanent Hold down the Temp and Option pushbuttons for a few seconds The op tion is permanently activated even if the appliance is switched off To deactivate it repeat the process Delay start TN 3h 6h 9h pea o This option allows you to delay the start of a wash programme by 3 6 or 9 hours by pressing the Delay start pushbutton You can change or cancel the delayed start time at any time before you press the Start Pause pushbutton by pres sing the Delay start pushb
5. e Screw the inlet hose back on and replace the drain hose This way the water remaining in the ho ses will be drained away avoiding any ice formation which would damage your appliance Before turning your appliance on again ensure that it is installed in an area whe re the temperature will not fall below freezing Use e Your appliance is intended for normal domestic use Do not use the appliance for commercial or industrial purposes or for any purpose other than the one it was designed for washing rinsing and spinning e Only wash items suitable for this treatment Refer to the instructions on the label of each item e Do not put items into the washing machine which have had stains removed with petrol alcohol trichlo rethylne etc If such stain removers have been used wait until the pro duct has evaporated before putting these items into the drum e Your appliance has been designed for use by adults Ensure children do not touch the appliance or use itas a toy Description of the appliance 7 Description of the appliance J 1 EE The control panel p FJ Lid handle EX Lever for moving the appliance ZJ Adjustable levelling feet Dispenser box LI Prewash II Wash amp Softener do not fill above the MAX symbol M The control panel EX Programme selector Spin speed selector Extra rinse pushbutton Lights of cycle progress Temperature pushbutton Start Pause push
6. gress Before making any changes to the cur rent programme you need to pause the washing machine by pressing the Start Pause pushbutton If the modification is not possible the Start Pause pus hbutton flashes red for a few seconds If you still decide to change the program me you must cancel the current pro gramme see below Cancelling the programme If you want to cancel the programme turn the programme selector to the Off position End of the programme The washing machine stops automatically the Start Pause pushbutton goes out and the light End comes on The lid can only be opened around 2 minutes after the washing machine has come to a stop Turn the programme selector to the Off position Remove washing Unplug and close water inlet tap A We recommend leaving the lid and drum open after use to ventilate the water tank How to run a wash cycle 11 Standby mode If the appliance is on but no commands are selected for 10 min before or after a cycle it goes into standby mode All the lights go out and Start Pause flashes slowly To exit standby mode simply press any pushbutton or turn the programme selector 12 washing guide Washing guide Sorting and preparing the washing Sort washing by type and care label refer to International symbols section below normal wash for tough fabrics which can withstand intense washing and spinning cycles de
7. 0 C 1 0 kg Mini programme For lightly soiled fabrics except for 2 5 kg Delay start wool Delicate Rinse Hand washed items can be rinsed in 2 5 kg this program Spin A spin cycle from 500 to 1000 900 800 rpm af 5 5 kg Delay start ter a Rinse hold or Night silence plus programmes table consumption 15 Programme Typeofwashing Type of washing Possible options Reference programme for test conforming to CEI 456 standard 60 Cottons programme with Eco option Cannot be used with programmes lower than 40 C Depending on model Consumption Programme Temperatu Average Washing type res consumption aC Litres kWh Cottons cold 90 2 20 140 150 Easy iron cold 60 125 135 Wool cold 40 55 65 Silk 25 35 Mini programme 252 Delicate Rinse 30 45 Spin Oils 10 20 Reference programme for test conforming to CEI 456 standard 60 Cottons programme with Eco option 49 L 1 04 kWh 140 min Average figures which can vary depending on conditions of use Consumptions shown refer to the maximum temperature for each programme 16 care and cleaning Care and cleaning Object trap Regularly clean out the object trap which is located at the bottom of the A drum Unplug the appliance before cleaning Descaling the appliance To descale the appliance use an appro priate non corrosive product designed for washing machines Read prod
8. ZANUSSI User manual A Electrolux Washing machine ZWT 8120 ZWT 9120 ZWT 10120 We were thinking of you when we made this product Welcome to the world of Electrolux Thank you for choosing a first class product from Electrolux which hopefully will provide you with lots of pleasure in the future The Electrolux ambition is to offer a wide variety of quality products that make your life more comfortable You find some examples on the cover in this manual Please take a few minutes to study this manual so that you can take advantage of the benefits of your new machine We promise that it will provide a superior User Experience delivering Ease of Mind Good luck 4 contents Contents VVOFNINOS 2 mme 5 Description of the appliance 7 How to run a wash cycle naese 8 Washing guide cccccceeseeseeeeeeee ees 12 Programmes table cccceeceeeeeee es 14 CONSUMPH ON scacasicdearnisindesnarraoiancina 15 Care and cleaning cccceeeeseeeeeeeee es 16 Operating problems ccceeeeeeee es 17 Technical Specifications ccceeeeees 20 Installation cascenaastatisertatinredstracsosiagaa 20 Environment ccecceeeeeeeeeeseeeeeeeeeees 23 The following symbols have been used in this user guide Important information about con cerning your safety and informa tion on how to avoid damaging the appliance General information Information concerning the envi ronment amp
9. ater and deter gent consumption You can therefore reduce the amounts recommended by detergent manufacturers Pour the amount of washing powder into the washing UU and prewash LU com partments if you have selected the orewash option Pour fabric softener into the compartment if necessary amp If you use another detergent type refer to the section detergents and additives in the washing guide Selection of desired programme You can find the right programme for different types of washing in the programme table see Programme table res O E D GY Cottons a Spin SSS A ue 2 A SNS es N Drain ky f 6 z A Easy iron Delicate ma Rinse gt s J Delicates Rinses z Le de O F F is See Wool hy L o B Mini 730 2 Handwash Programme E a Soak T OS silk Special Turn the programme selector to the required programme The Start Pause pushbutton flashes green A If you turn the programme selector to another programme while a cycle is in progress the appliance will ignore the new selected programme The Start Pause pushbutton flashes red for a few seconds Selecting the temperature gt 20 Press the Temp pushbut 60 ton repeatedly to increase 40 or decrease the temperatu 46 re if you want your washing e to be washed at a different temperature to the one se lected by the appliance The un gt symbol means a cold p
10. ater inlet hose can not be exten ded If it is too short please contact the after sales service 22 technical specifications installation Drainage The connector at the end of the flexi ble hose can be at tached to all common types of standpipe Attach the connec tor to the standpipe with the hose Clamp supplied with the Fit the U piece on the drainage hose Place everything in a drainage point or in a sink at a height of between 70 and 100 cm Ensure it is positioned secu rely Air must be able to enter the end of the hose to avoid any risk of siphoning A The drain hose must never be stretched If it is too short contact a tradesperson Electrical connection This washing machine must only be connected in single phased 230 V Check the fuse size 10 A for 230 V The appliance must not be connected with an extension lead or multi plug adaptor Ensure that the plug is earthed and that it is in accordance with current norms depending on model Positioning Position the appliance on a flat and hard surface in a ventilated location Ensure the appliance does not come into con tact with the wall or other furniture To move the appliance proceed as fol lows TO move your ap pliance place it on its rollers by pulling the lever located at the base of the ap pliance hard from right to left Once the appliance is in the desired position push the lever back to its original posi
11. button Option pushbutton Delay start pushbutton O Re Q Go 3h 6h 9h Spn ZX Synthetics 90 e e e Easy 60 J Drain by a iron 40 Prewash U i 30 Eco O Delicate pas a s Delicates J 500 Super Rinse oR 1000 J e J Quick J gt A Option fae Rinses z LF Wool gt J P B L 900 Mini 730 4y Handwash Programme J a s s Soak T IF silk ae us Special 5 5KglAA Made in France ZWT 19120 8 How to run a wash cycle How to run a wash cycle Using for the first time e Ensure the electrical and water con nections comply with the installation instructions e Remove the polystyrene insert and all other items inside the drum e Run an initial wash cycle at 90 C without any washing but with deter gent to clean the water tank Daily use Loading washing e Open the lid of the appliance e Open the drum by depressing the loc king button The two shutters unlock automatically e Load the washing close the drum and the lid of your washing machine CRE e n gt e pe mm u ss SSD Before closing the lid of your appliance ensure that the drum is properly closed e When the two shutters are closed e locking button A released Proportioning of detergents Your washing machine has been desi gned to reduce your w
12. half capacity for processed cot tons and synthetic fibres e to a third of its capacity for very fra gile items such as net curtains and woollens For mixed loads fill drum depending on most fragile materials Detergents and additives Only use detergents and additives desi gned for use in a washing machine Re fer to manufacturer s recommendations and also Dispenser box and Using the ri ght amount of detergent sections We do not recommend mixing different types of detergents This may spoil the washing The amount of detergent to be used de pends on the size of the load the hard ness of the water and how heavily soiled the washing is If the water is soft reduce the amount slightly If the water contains lime scale a descaler is recommended or if the washing is heavily soiled or stained in crease the amount slightly You can obtain information on the hard ness level of water in your area by con tacting your water company or other competent source There are no restrictions on the use of powder detergents Liquid detergents must not be used when a prewash has been selected For cycles without prewash they can be ad ded either via means of a dosing ball or in the detergent compartment In either International symbols NORMAL WASH Wash at 95 C at 95 C Wash at 60 Wash at 60 C washing guide 13 case the wash cycle must be started immediately Detergent tablets or doses must be pla ced
13. in the detergent compartment of your appliance s dispenser box For stain removal before a wash cycle please refer to manufacturer s recom mended amounts and instructions If you use a detergent to remove stains the wash cycle must be started imme diately Tey Ve a ey y Wash at 40 Wash at 40 C Wash at 30 Wash at 30 C DELICATE Hand wash Do not wash WASH ted solution BLEACHING Whitewashing _A allowed cold only and in dilu No whitewashing bleach High temperature Mid temperature Low temperature Do not iron max 200 C max 150 C max 100 C O B Dry cleaning all common solvents except trichlorethylene Dry cleaning only oil based solvents and R113 DRY Dry cleaning Do not dry clean CLEANING all common solvents High GERS LE O LE DRYING Dry flat Hang dry Dry on clothes Tumble drying Do not tumble dry hanger permitted 14 programmes table consumption Programmes table Programme Type of washing Possible options Cottons White or colour e g normally soiled work 5 5 kg clothes bed linen table linen body linen towels Easy iron Reduces creasing and makes ironing easier 1 0 kg Prewash Extra rinse Rinse hold Delay start Wool Machine washable wool carrying the labels pure 1 0 kg new wool machine washable does not shrink Rinse hold Night silence plus Delay start Silk Fabric machine washable at 3
14. ing If all transit packaging is not comple tely removed the appliance or sur rounding furniture could be damaged e Connection to the water supply must be carried out by a qualified plumber e f your domestic electrical circuit needs adapting to allow the appliance to be plugged in use a qualified electrician e Ensure that after installation the power cable is not trapped under the appliance e If the appliance is installed on carpe ted floor ensure that the carpet does not obstruct any ventilation ducts located at the base of the appliance e The appliance must be equipped with an earthed power plug which conforms to regulations e Before connecting your appliance to the power supply carefully read the instructions in the chapter entitled Electrical connection e Replacing the power cable should only be carried out by the After Sales Service e The manufacturer cannot be held responsible for any damage resulting from incorrect installation 6 warnings Precautions to be taken against frost If your appliance is exposed to tempera tures below O C the following precau tions must be taken e Close the tao and disconnect the inlet hose e Place the end of this hose and the drain hose in a basin on the floor e Select the Drain programme let it run until the end of the cycle e Disconnect the appliance from the power supply by turning the program selector to Stop e Unplug the appliance
15. li cate wash for delicate fabrics which need to be treated with care For mixed loads loads with items of dif ferent types of material choose a programme and a temperature suita ble for the most fragile material Wash whites and colours separately Otherwise whites will be coloured or will turn grey New coloured clothes often contain excess dye It is recommended to wash such items separately the first time Follow care instructions wash separately and wash separately several times Empty pockets and unfold items Remove loose buttons pins and fas teners Close zip fasteners tie ups laces and straps Turn multilayered fabrics sleeping bags anoraks etc coloured head wear wool and material with printed designs inside out Wash small fragile items tights bras etc in a net bag Take special care with curtains Remove hooks and place net cur tains in a net or bag socks Wash loads depending on type of materials The amount of washing placed in the drum must not exceed the maximum capacity of the washing machine This Capacity can vary depending on the type of materials Reduce the quantity if washing is heavily soiled or made of ab sorbant material Not all textiles have the same volume in the drum or the same water absorption levels In general the drum must there fore be filled e to full capacity but avoiding exces sive pressure on cotton linen and cotton linen mixtures e to
16. priate amount of deter gent for the hardness of the water cf section Using the right amount of detergent the size of the load and how soiled the washing is www electrolux com 108 3015 01 09 07
17. tion Accurate levelling avoids vibrations noi se and prevents the appliance from mo ving when running Environment Disposing of the appliance CG All materials carrying the symbol are recyclable Dispose of them at a waste collection site enquire at your local council for collection and recycling When disposing of your appliance re move all parts which could be dange rous to others cut off the power supply cable at the base of the appliance The symbol on the product or on its packaging indicates that this product may not be treated as household waste Instead it shall be handed over to the ap plicable collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environ ment and human health which could otherwise be caused by inappropriate waste handling of this product For more detailed information about recycling of this product please contact your local city office your household waste dispo sal service or the shop where you pur chased the product environment 23 Protecting the environment To save water and energy and therefore helo protect the environment we re commend the following e Whenever possible use the appliance at full capacity and avoid partial loads e Only use the prewash and soak pro grammes for heavily soiled items e Use an appro
18. uct la bel for recommended amounts and how often descaling should be carried out The exterior Use warm soapy water to clean the ex terior of the appliance Never use alco hol solvents or similar products Dispenser box To clean proceed as follows Water inlet filters To clean proceed as follows operating problems 17 Operating problems Numerous checks were carried out on your appliance before it left the factory However should you notice a malfunction please refer to the sections below before contacting the after sales service Problems Causes The washing machine doesn t start or doesn t fill e the appliance isn t plugged in correctly the electrical installation isn t working e the lid of your appliance and the drum shutters aren t closed firmly e the programme start command hasn t been properly selected e there is a power failure e the water supply has been cut off e the water inlet tap is closed e the water inlet filters are dirty e ared tab appears on the water inlet hose The appliance fills but the drainage U piece is fixed too low see instal empties straight away The washing machine doesn t rinse or doesn t empty You have found water around the washing machine lation section e the drain hose is blocked or bent e the drainage filter is obstructed e the out of balance detector has been activated washing is unevenly distributed in the drum
19. utton again when all indicators are off the wash programme will start immediately If you have already pressed the Start Pause pushbutton and you want to change or cancel the delayed start pro ceed as follows e To cancel the delayed start and start the cycle immediately press Start Pau se and then Delay start Press Start Pause to start the cycle e To change the timer delay period you must go through the Off position and reprogram your cycle A The lid will be locked during the delayed start time If you need to open it you must first pause the appliance by pres sing the Start Pause pushbutton After closing the lid again press the Start Pause pushbutton Start of the programme _ Press the Start Pause gt pushbutton to start the cycle the corresponding J light will come on green It is normal for the programme selector to remain stationary during the cycle J The light corresponding as to the current cycle is il Er luminated gt Interrupting a programme Adding washing during the first 10 minutes Press the Start Pause pushbutton the corresponding light will flash green while the appliance is paused The lid can only be opened around 2 minutes after the washing machine has come to a stop Press the Start Pause pus hbutton again to continue the program me Modifying the programme in pro
20. wash Selecting the spin speed Turn the spin speed selector on the desired speed You can also select No Spin Rinse hold or Night silence plus The maximum speeds are for Cottons Wool and Handwash 1000 rom ZWT10120 900 rom ZWT9120 800 rom ZWT8120 for Synthetics and Easy iron 900 rom ZWT10120 ZWT9120 800 rom ZWT8120 for Delicates Silk and Mini programme 700 rpm At the end ofthe programme if you have selected Rinse hold GJ or Night silence plus you then need to select a spin Delicate Spin or Drain programme to finish the cycle Night silence plus The washing machine does not empty the water after the final rinse which pre depending on model How to run a wash cycle 9 vents the washing from creasing Be cause there are no spin cycles the washing programme is very quiet and can be selected at night In Cotton and synthetics programmes the rinsing cy cle uses more water Rinse hold UJ The washing machine will not drain the water from the last rinse so will not crease the laundry Selecting options Ye Prewash You must select the m o different options af super ter selecting the ne programme and Option amp before pressing the it Start Pause pus CED J hbutton see Pro gramme table Press the desired button s the corres ponding lights come on If pressed

Download Pdf Manuals

image

Related Search

Related Contents

029-5306-02 convNT ITE gd_eng  CNED, Inscription, mode d`emploi 2013-2014    ANNEXE 1 avis autorité environnementale  this document is for review pu full use d nt is for review purposes  

Copyright © All rights reserved.
Failed to retrieve file