Zanussi S1 User's Manual
Contents
1. 30 Washing and drying hints 14 Installation instruction 31 Before the first use 17 Environmental concerns 35 Operating Sequence 18 Safety information In the interest of your safety and to ensure the correct use before installing and first using the appliance read this user manual carefully including its hints and warnings To avoid unnecessary mistakes and accidents it is important to ensure that all people using the appliance are thoroughly familiar with its operation and safety features Save these instructions and make sure that they remain with the appliance if it is moved or sold so that everyone using it through its life will be properly informed on appliance use and safety General safety e It is dangerous to alter the specifications or attempt to modify this product in any way e During high temperature washing and drying programmes the door glass may get hot Do not touch it e Make sure that small pets do not climb into the drum To avoid this please check into the drum before using e Any objects such as coins safety pins nails screws stones or any other hard sharp material can cause extensive damage and must not be placed into the machine e Only use the advised quantities of fabric softener and detergent Damage to the fabric can ensue if2. A cut off plug inserted into a 13 amp socket is a serious safety shock hazard Ensure that the cut off plug is disposed of safely Should the appliance power supply cable need to be replaced this must be carried out by our Service Force Centre The power supply cable must be easily accessible after installing the appliance Permanent connection In the case of permanent connection it is necessary that you install a double pole switch between the appliance and the electricity supply mains with a minimum gap of 3mm between the switch contacts and of a type suitable for the required load in compliance with the current electrical regulations The switch must not break the yellow and green earth cable at any point Fitting under a counter WARNING Before any work to the appliance you must disconnect the plug from the power socket If the counter is too low and it becomes necessary to remove the top lid of the washer dryer a steel plate known as a height reduction kit must be used Important For safety reasons it is dangerous to fit the appliance under a counter without the steel plate which you can order in your nearest Service Force Centre The top must be fixed to the cabinet as follows Unscrew the screws from the back panel of the appliance Push the worktop to the back and raise it to remove see the picture above Environmental concerns Packaging materials The materials ma
3. Too much detergent or unsuitable detergent creates too much foam has been used e Reduce the detergent quantity or use another one Check whether there are any leaks from one of the inlet hose fittings It is not always easy to see this as the water runs down the hose check to see if it is damp e Check the water inlet hose connection The inlet hose is damaged e Replace it with a new one The emergency emptying cap has not been replaced on the filter after cleaning Refit the emergency emptying cap on the filter Too little detergent or unsuitable detergent has been used Increase the detergent quantity or use another one Stubborn stains have not been treated prior to washing e Use commercial products to treat the stubborn stains The correct temperature was not selected e Check if you have selected the correct temperature Excessive laundry load e Reduce the laundry load ZANUSSI The door will not open The machine vibrates or is noisy Spinning starts late or the machine does not spin The machine makes an unusual noise The programme is still running e Wait until the end of washing cycle The door lock has not been released e Wait a few minutes There is water in the drum Select drain or spin programme to empty out the water The transit bolts and packing have not been removed e Check the correct installation of the appliance The support feet have not been adjusted e Check
4. Any necessary adjustment can be made with a spanner Accurate levelling prevents vibration noise and displacement of the machine during operation Never place cardboard wood or similar materials under the machine to compensate for any unevenness in the floor 31 Special conditions If the floor is carpeted or covered with crumbly or soft material insert a rigid support base under the feet to prevent noise vibration or displacement The base should protrude a few centimetres beyond the edges of the machine WARNING The machine should NOT be placed on deep pile carpeting NOTE Please ensure that when the appliance is installed it is easily accessible for the engineer in the event of a breakdown Water inlet The inlet hose is already screwed on the back of the appliance 1 Set the hose correctly by loosening the ring nut After positioning the inlet hose be sure to tighten the ring nut again to prevent leaks A Attention Do not place the inlet hose downwards Angle the hose to the left or right depending on the position of your water tap 2 This appliance must be connected to a cold water supply Connect the hose to a tap with a 3 4 thread The inlet hose must not be lengthened If it is too short and you do not wish to move the tap you will have to purchase a new longer hose specially designed for this type of use 32 NOTE Installation should comply with local water
5. check that the drum is empty If you do not intend to carry out another wash close the water tap Leave the door open to prevent the formation of mildew and unpleasant smells Stand by once the programme has finished after a few minutes the energy saving system will be enabled The brightness of the display is reduced By pressing any button the appliance will come out of the energy saving status Operating sequence Drying only The recommended load to dry in your washer dryer is 3 kg for cotton and 2 kg for synthetics Note It is possible also to dry up to 4 kg of cot ton items see the drying times table The water tap must be open and the drain hose must be positioned in the sink or connect ed to the drain pipe 1 2 Load the laundry Turn the selector dial to Cottons or Synthetics programme in the Drying section Select the duration of the ie cycle by pressing repeatedly button until the time you want appears on the display see the drying programmes For Cottons you can select a drying time from 10 minutes to 250 minutes 4 72 For Synthetics you can select a drying time from 10 minutes to 130 minutes 2 10 Every time you press the button the time increases by 5 mins 20 Note The drying time will automatically increase by up to 2 minutes This is quite normal 4 Press the button BE to start the pro gramme After the programme has started the time remaining is upd
6. emptying out the water of the last rinse in programmes with the Rinse Hold option Turn first the programme selector dial to Off then select programme Drain and depress the button a Separate spin for hand washed garments and after programmes with Rinse Hold option Before selecting this programme the selector dial must be turned to Off You can choose the speed by means of the relevant button to adapt it to the fabrics to be spun To reset a programme and to switch off the machine turn the selector dial to Off A new programme can now be selected Washing and drying hints Sorting the laundry Follow the wash code symbols on each garment label and the manufacturer s washing instructions Sort the laundry as follows whites coloureds synthetics delicates woollens Temperatures for normally soiled white cottons and linen e g tea cloths towels tablecloths sheets 90 or 95 for normally soiled colour fast garments e g shirts night dresses pyjamas in linen cotton or synthetic fibres and for lightly soiled white cotton e g underwear 50 60 for delicate items e g net curtains mixed laundry including synthetic fibres and woollens bearing the label pure new wool machine washable non shrink 30 40 Cold Before loading the laundry Never wash whites and coloureds together Whites may lose their whiteness in the wash New coloured items may run in the first wash
7. hardness Information on hardness of the water in your area can be obtained from the relevant water supply company 16 Follow the product manufacturers instructions on quantities to use Degrees of water hardness Follow the product manufacturers instructions on quantities to use Use less detergent if e you are washing a small load e the laundry is lightly soiled e large amounts of foam form during washing Level Characteristic dH T H 1 soft 0 7 0 15 2 medium 8 14 16 25 3 hard 15 21 26 37 4 very hard gt 21 gt 37 Before the first use WARNING Ensure that the electrical and water connections comply with the installation instructions IMPORTANT Remove the polystyrene block and any material from the drum IMPORTANT Pour 2 litres of water into the main wash compartment UL of the detergent drawer in order to activate the ECO valve Then run a cotton cycle at 90 C or 95 C without any laundry in the machine to remove any manufacturing residue from the drum and tub Pour 1 2 a measure of detergent into the dispenser drawer and start the machine Child safety lock Fy This device permits you to leave the appliance unattended without having the worry that children might be injured by or cause damage to the appliance This function remains enabled also when the washer dryer is not working There are two different ways to set this option e before pressing the A it will be
8. impossible to start the machine e after pressing the button H it will be impossible to change any other programme or option To enable disable this option press simultaneously for about 6 seconds buttons and B until the icon amp appears disappears on from the display ZANUSSI Acoustic signals The machine is supplied with an acoustic device which sounds in the following cases e atthe end of the cycle e in the event of operating problems By pressing the buttons H and simultaneously for about 6 seconds the acoustic signal is deactivated except for the events of operating problems By pressing these 2 buttons again the acoustic signal is reactivated Operating sequence Washing only Washing 1 Load the laundry Open the door by carefully pulling the door handle outwards Place the laundry in the drum one item at a time shaking them out as much as possible Close the door Measure out the detergent and the fabric softener Pull out the dispenser drawer until it stops Measure out the amount of detergent required pour it into the main wash compartment LIL and if you wish to carry out the prewash phase pour it into the compartment marked LU If required pour fabric softener into the compartment marked 3 the amount used must not exceed the MAX mark in the drawer Close the drawer gently Select the required programme by turning the programme selector dial ij Turn the
9. is not properly inserted in the power socket Insert the plug into the power socket There is no power at the socket e Please check your domestic electrical installation The washer dryer does not start The main fuse or the fuse in the plug has blown e Replace the fuse The selector dial is not correctly positioned and the button Fal has not been pressed e Please turn the selector dial and press the button Fl again The Child Safety Lock option has been selected Disable the Child Safety Lock option The water tap is closed 72 Open the water tap The inlet hose is squashed or kinked E72 e Check the inlet hose connection The filter in the inlet hose is blocked 10 e Clean the water inlet hose filter The door is not properly closed E4 Close the door firmly The machine does not fill 25 The machine fills then empties immediately The machine does not empty and or does not spin There is water on the floor Unsatisfactory washing results 26 Possible Cause Solution The end of the drain hose is too low Refer to relevant paragraph in water drainage section The drain hose is squashed or kinked EZ e Check the drain hose connection The drain pump is clogged E27 e Clean the drain pump The Rinse Hild or No spin option has been selected Select the Drain or Spin programmes The laundry is not evenly distributed in the drum e Redistribute the laundry
10. programme selector dial to the required programme The green light of button B starts to flash On position Off the programme is reset and the machine is switched off 18 At the end of the programme the selector dial must be turned to position Off to switch the machine off IMPORTANT If you turn the programme selector dial to another programme when the machine is working the red light of button K will flash 3 times and the message Err is displayed to indicate a wrong selection The machine will not perform the new selected programme Select the spin speed or No Spin or Rinse Hold option by pressing button Bj When selecting a programme the light corresponding to the maximum speed allowed for that programme will illuminate refer to the section Programme table for the maximum allowed by each cycle spin speed The relevant light will light up Select the desired option by pressing the buttons J and EJ Depending on the programme different functions can be combined These must be selected after choosing the desired programme and before pressing the button K The relevant light will light up In any case if an option is chosen that is not allowed with the selected programme the message Err will be displayed on the display for a few seconds and the red light of the button K start flashing IMPORTANT For the compatibility of the options with the washing programmes please refer to the Programme t
11. remove the mains plug from the socket Proceed as follows Unplug the appliance e if the appliance is operating wait if necessary until the water has cooled down open the pump door levering on the groove with a coin e place a bowl with a small edge close to the pump to collect any spillage Care and cleaning pull out the emergency emptying cap from the filter cover using a pliers e When no more water comes out unscrew the pump cover by turning it anti clockwise using pliers and remove the filter Always keep a rag nearby to dry up any water spillages when removing the cover Clean the filter under a tap to remove any traces of fluff e Remove foreign bodies and fluff from the pump seat and from the pump impeller e Check carefully whether the pump impeller rotates it rotates jerkily If it doesn t rotate please contact your Service Centre e Replace the filter into the pump by inserting it correctly into the special guides Screw the pump cover firmly by turning it clockwise ZANUSSI e Replace the emergency emptying cap into the filter cover and fix it firmly IMPORTANT When the appliance is in use and depending on the programme selected there can be hot water in the pump Never remove the pump cover during a wash cycle always wait until the appliance has finished the cycle and is empty When replacing the cover ensure it is securely retigh
12. they should therefore be washed separately the first time Make sure that no metal objects are left in the laundry e g hair clips safety pins pins Button up pillowcases close zip fasteners hooks and poppers Tie any belts or long tapes Remove persistent stains before washing Rub particularly soiled areas with a special detergent or detergent paste Treat curtains with special care Remove hooks or tie them up in a bag or net 14 Avoid drying dark clothes with light coloured fluffy items such as towels as these can attract the fluff Remove the laundry when the appliance has finished drying To avoid a static charge when drying is com pleted use either a fabric softener when you are washing the laundry or a fabric conditioner specifically for tumble dryers Particularly delicate items such as synthetic curtains woollen and silk garments with metal inserts nylon stockings bulky garments such as anoraks bedcovers quilts sleeping bags and duvets must not be machine dried Garments padded with foam rubber or materi als similar to foam rubber must not be machine dried they represent a fire hazard Also fabrics containing residues of setting lotions or hair sprays nail solvents or similar solutions must not be machine dried in order to avoid the formation of harmful vapours For drying follow the indications given on the manufacturer s labels g May be tumble dried Q Drying at high temperature Dryin
13. you over fill Refer to the manufacturer s recommendations of quantities e Wash small items such as socks laces washable belts etc in a washing bag or pillow case as it is possible for such items to slip down between the tub and the inner drum e Do not use your washer dryer to wash articles with whalebones material without hems or torn material ZANUSSI e Always unplug the appliance and turn off the water supply after use cleaning and maintenance e Under no circumstances should you attempt to repair the machine yourself Repairs carried out by inexperienced persons may cause injury or serious malfunctioning Contact your local Service Centre Always insist on genuine spare parts Installation e This appliance is heavy Care should be taken when moving it e When unpacking the appliance check that it is not damaged If in doubt do not use it and contact the Service Centre e All packing and transit bolts must be removed before use Serious damage can occur to the product and to property if this is not adhered to See relevant section in the user manual e After having installed the appliance check that it is not standing on the inlet and drain hose and the worktop is not pressing the electrical supply cable e lf the machine is situated on a carpeted floor please adjust the feet in order to allow air to circulate freely under the appliance e Always be sure that there is no water leakage from hoses and thei
14. 18mm If your drain hose looks like this see below you do not require the U piece Just push the hose firmly into the standpipe 2 Onto a sink outlet spigot If the outlet spigot has not been used before remove any blanking plug that may be in place Push the drain hose onto the spigot and secure with a clip ensure a loop is formed in the drain hose see diagram to prevent waste from the sink entering the washer dryer ZANUSSI Important Before connecting the machine to new pipework or to pipework that has not been used for some time run off a reasonable amount of water to flush out any debris that may have collected in the pipes In the interest of the environment Washer dryers should be connected to the FOUL drainage system the water will then be taken to a sewage works for treatment before being discharged safely into a river It is essential that these appliances are not connected to the surface water drainage system as this water is discharged directly into a river or stream and may cause pollution If you require any further advice please contact your local water authority S i i SHOWER SINK TOILET BIDET WASHING MACHINE DISHWASHER CET ee RAINWATER FOUL DRAIN i 2 SURFACE WATER DRAINS amp SEWERS SEWAGE TREATMENT DISCHARG WORKS Y TREATED DISC
15. HARGE RIVER FOUL SEWERS UNTREATED E RIVER 33 Electrical connection Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person WARNING This appliance must be earthed The manufacturer declines any liability should this safety measure not be observed Before switching on make sure the electricity supply voltage is the same as that indicated on the appliance s rating plate IMPORTANT Information on the electrical connection is given on the rating plate on the inner edge of the appliance door The appliance is supplied with a 13amp plug fitted In the event of having to change the fuse in the plug supplied a 13amp ASTA approved BS1363 A fuse must be used Should the plug need to be replaced for any reason proceed as described below The wires in the mains lead are coloured in accordance with the following code The wire coloured green and yellow must be connected to the terminal marked with the letter E or by the earth symbol or coloured green and yellow The wire coloured blue must be connected to the terminal marked N or coloured black The wire coloured brown must be connected to the terminal marked L or coloured red 34 Upon completion there must be no cut or stray strands of wire present and the cord clamp must be secure over the outer sheath 4 WARNING
16. ZANUSSI f 4 4 gt User manual Se J y S P d d N 4 4 Washer dryer x yp E lt P N A ZWD 12270 W1 ZWD 12270 S1 ZWD 12270 G1 ZWD 14270 W1 ZWD 16270 W1 Thank you for selecting our appliance We wish you lots of enjoyment with your new appliance and we hope that you will consider our brand again when purchasing household appliances Please read this user manual carefully and keep it throughout the product life cycle as a reference document The user manual should be passed on to any future owner of the appliance The following symbols are used in this manual Important information concerning your personal safety and information on how to avoid damaging the appliance i General information and tips wy Environmental information Content Safety information 3 Washing only 18 Description of the appliance 5 Drying only 20 Detergent dispenser drawer 5 NON STOP programme 21 Control panel and functions 6 Care and cleaning 22 Programme table 10 What to do if 25 Drying times 12 Technical data 29 Programme information 13 Consumption values
17. able Start the programme by pressing button KJ To start the selected programme press this button the corresponding green pilot light stops flashing The appliance starts operating and the door is locked To interrupt a programme which is running depress the button Bal the corresponding green pilot light starts to flash To restart the programme from the point at which it was interrupted press the same button again IMPORTANT If an incorrect option is selected the red pilot light of the button J flashes 3 times and the message Err is displayed for a few seconds Altering an option or a running programme It is possible to change some options before the programme carries it out Before you make any change you must pause the washer dryer by pressing the button B Changing a running programme is possible only by resetting it Turn the programme selector dial to Off and then to the new programme position Start the new programme by depressing the button K again The washing water in the tub will not be emptied out Interrupting a programme Press the button K to interrupt a programme which is running the corresponding light starts to flash Press the same button again to restart the programme Cancelling a programme Turn the selector dial to Off to cancel a programme which is running You can now select a new programme ZANUSSI Opening the door after the programme has started First set the mach
18. ance of nature The choice of detergent will depend on the type of fabric delicates woollens cottons etc the colour washing temperature and degree of soiling All commonly available washer dryer detergents may be used in this appliance e powder detergents for all types of fabric e powder detergents for delicate fabrics 60 C max and woollens e liquid detergents preferably for low temperature wash programmes 60 C max for all types of fabric or special for woollens only The detergent and any additives must be placed in the appropriate compartments of the dispenser drawer before starting the wash programme If using concentrated powder or liquid detergents a programme without prewash must be selected The washer dryer incorporates a recirculation system which allows an optimal use of the concentrated detergent Pour liquid detergent into the dispenser drawer compartment marked LIL just before starting the programme Any fabric softener or starching additives g be poured into the compartment marked before starting the wash programme Follow the product manufacturer s recommendations on quantities to use and do not exceed the MAX mark in the detergent dispenser drawer Quantity of detergent to be used The type and quantity of detergent will depend on the type of fabric load size degree of soiling and hardness of the water used Water hardness is classified in so called degrees of
19. ated every minute 5 At the end of the programme the buzzer sounds Three flashing zeros 2 02 will appear on the display At this point begins an anti crease phase which lasts about 10 minutes The door is locked and can be opened only at the end of this phase Note If you wish to open the door before the anti crease phase or to interrupt it press any key or turn the programme selector dial to any programme position except Off The door can be opened immedia tely or in a few minutes depending on the model Turn the selector dial to the Off position to switch the machine off Remove the laundry ZANUSSI NON STOP programme Washing and Timed Drying The recommended load to wash and dry in your washer dryer is 3 kg for cotton and 2 kg for synthetics Note It is possible also to wash and dry up to 4 kg of cotton items see the drying times table Do not use a dosing device ball when carrying out a washing amp drying programme 1 Load the laundry 2 Add detergent and fabric softener 3 Switch the machine on by turning the selector dial to the selected wash pro grammeffabric 4 Select the drying time by pressing button see the drying programmes 5 Select the required options by pressing the relevant buttons The display shows the entire duration of the washing and the selected drying cycle If possible do not select a spin speed lower than that proposed by the appliance t
20. authority and building regulations requirements A minimum water pressure of 0 05 MPa 0 5 bar is required for safe operation of the appliance lf you cannot make the cold water connection direct from the rising mains you may be able to operate the appliance from your cold water storage system There should be a minimum vertical distance of 5 02m 16 5 ft between the appliance s inlet and the bottom of the water storage tank Water drainage This appliance is designed to be permanently plumbed into your home s drainage system using one of the following methods 1 Into a drainage standpipe Firstly form a hook in the end of the drain hose using the U piece supplied supplied Place the drain hose into your standpipe which should have an internal diameter of approximately 38mm thus ensuring there is an air break between the drain hose and standpipe 38mm 1L5 fw standpipe 4 diameter l e 30 cm 12 When discharging into a standpipe ensure that the top of the standpipe is no more than 90 cm 35 4 and no less than 60 cm 23 6 above floor level 5 a w The drain hose may be extended to a maximum of 4 metres An additional drain hose and joining piece is available from your local Service Force Centre The joining piece must have an internal diameter of
21. detergent according to the water hardness the degree of soiling and the quantity of laundry being washed 35 ZANUSSI www electrolux com www zanussi electrolux co uk 132963663 00 122010 Subject to change without notice CE
22. e Wash light go off the End KJ pilot light illuminates the display shows three flashing zeros 2 22 and the door is blocked to indicate that the water must be emptied out To empty out the water see chapter At the end of the programme Prewash button EJ Select this option if you wish your laundry to be prewashed at 30 C before the main wash not available for all programmes The prewash ends with a short spin in programmes for cotton and synthetics whereas in the programmes for delicate fabrics the water is only drained Intensive button EJ This option can be selected for heavily soiled laundry the washing intensity will be increased and the washing time will be prolonged by a few minutes depending on the selected type of fabric Super Quick button EJ A very short cycle for slightly soiled items that have been used or worn for a short time The washing time will be reduced according to the type of fabric and the selected temperature We recommend that you reduce the load size ZANUSSI Extra Rinse option button 4 This option is recommended for people who are allergic to detergents and in areas where the water is very soft The machine performs some additional rinses For the options compatibility with each programme please refer to the Programme table Drying time button FA By pressing this button you can select a timed drying for cotton or synthetics The corresponding ligh
23. e a note of the model serial number and purchase date of your machine the Service Centre will require this information Prod No SOG NOM meee 28 ZANUSSI Technical data Dimensions Width 60 cm Height 85 cm Depth including the porthole 63 cm Electrical connection Voltage Information on the electrical connection is given on the rating Overall power Fuse plate on the inner edge of the appliance door Water supply pressure Minimum 0 05 MPa Maximum 0 8 MPa Maximum Load Cotton 6 kg Synthetics 3 kg Delicates 3 kg Woollens and handwash 2 kg Cotton 3 kg Meramurn Drying Lea Cotton Big Capacity 4 kg Synthetics 2 kg 1600 rpm ZWD 16270 W1 Spin Speed Maximum 1400 rpm ZWD 14270 W1 1200 rpm ZWD 12270 W1 1200 rpm ZWD 12270 S1 1200 rpm ZWD 12270 G1 29 Consumption values Programme Programme Energy Water duration consumption consumption in minutes in kWh in litres Cottons 90 C p 2 0 61 2 Cottons 60 Eco ES 1 02 54 55 Cottons 60 C 40 C a gt 13 58 S23 Cottons 40 Eco Leas 1 14 54 o a Synthetics 50 C 40 C Sfp 0 8 51 Bes Synthetics Easy Iron 40 C g 2 0 35 60 5 Delicates 40 C 30 C 2 0 55 60 se Wool 40 C Me 0 4 53 i Information The consumption data shown on this chart isto The Cottons 60 Eco is the reference be considered purely indicative as it may vary programme with a load of 6 kg for the data depending on the quantity and type of
24. e not left their gas lighters disposable or otherwise in their clothing Never dry items that have had contact with chemicals such as dry cleaning fluid These are of a volatile nature and could cause an explosion Only tumble dry items which have been washed in water or require airing Plastic detergent dispensers should not remain in the drum during the drying cycle as the plastic used is not designed to withstand the heat If you wish to wash through to dry you should use the conventional detergent dispenser drawer e Never pull the power supply cable to remove the plug from the socket always take hold of the plug itself e Never use the washer dryer if the power supply cable the control panel the working surface or the base are damaged so that the inside of the washer dryer is accessible Child safety e This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Young children should be supervised to ensure that they do not play with the appliance The packaging components e g plastic film polystyrene can be dangerous to children danger of suffocation Keep them out of children s reach Keep all detergents in a safe place out of children s reach Make sure that children or pe
25. ed Prewash Intensive Short spin at 900 rpm 50 40 fabrics Super Quick Max Load 3 Kg Sia ine Reduced Load 1 5 Kg Synthetic or mixed Main wash rinses Synthetics i TH O E eni Spin red amp J Short spin at 900 rpm Easy iron 40 washed and spun Prewash Extra rinse Max Load 1 5 Kg Main wash rinses Delicates Delicate fabrics for 9 u es Short spin at 700 rom 40 30 example curtains Prewash Super Quick Max Load 3 Kg Intensive Extra Rinse Reduced Load 1 5 Kg If you select the option Super Quick by pressing the button El we recommend that you reduce the load sizes as indicated in the table above Full loading is possible however with somewhat reduced cleaning results 10 Programme table ZANUSSI Wool 40 Handwash 30 Cold Mini 30 30 Silk 30 Rinse Drain Spin Programme for wool Pure new wool non shrink machine washable label Special programme for hand washing fabrics Short cycle for lightly soiled fabrics Silk items to be gently washed and spun Separate rinse cycle for hand washed cotton items For emptying out the last rinse water in programmes with the Rinse Hold option Separate spin for cottons Spin red oO Spin red B Oo 0 Spin red O Extra rinse Spin red Programme Description of Main wash rinses Short spin at 900 rom Max Load 2 Kg Main wash rinses Short spin at 900 rpm Ma
26. emaining is updated every minute After having pressed button the light m illuminates and stays on Selected drying time After selecting a drying programme the drying time is displayed in minutes or in hours and minutes max 250 mins 4 72 only for cot tons After the programme has started the time remaining is updated every minute lincorrect option selection The incorrect option selection is indicated by the message Err displayed for a few seconds and by flashing of the red light button g lAlarm codes In the event of operating problems some alarm codes can be displayed see paragraph What to do if End of programme The End of programme is indicated by three flashing zeros 2 80 The light XK illumina tes After a few minutes the door can be ope ned EA child safety lock This device permits you to leave the appliance unattended during it s functioning Heating phase During the washing cycle the display shows a temperature icon to indicate that the appliance has started the heating phase of the water in the tub Functions No spin button B By selecting this option all the spinning phases are suppressed to prevent the fabrics from creasing The final spin is replaced by a draining phase Rinse Hold button A By selecting this option the water of the last rinse is not emptied out to prevent the fabrics from creasing When the programme has finished the Start Pause and th
27. g at reduced temperature B Do not tumble dry IMPORTANT As a dryer the machine works on the condensation principle Therefore the water tap must be open and the drain hose must drain water into a sink or into the drain pipe even during the dry ing cycle Maximum loads Recommended loads are indicated in the programme charts General rules Cotton linen drum full but not too tightly packed Synthetics drum no more than half full Delicate fabrics and woollens drum no more than one third full Washing a maximum load makes the most efficient use of water and energy For heavily soiled laundry reduce the load size Laundry weights The following weights are indicative bathrobe 1200 g napkin 100 g quilt cover 700 g sheet 500 g pillow case 200 g tablecloth 250 g towelling towel 200 g tea cloth 100 g night dress 200 g ladies briefs 100 g man s work shirt 600 g man s shirt 200 g man s pyjamas 500 g blouse 100 g men s underpants 100 g Removing stains Stubborn stains may not be removed by just water and detergent It is therefore advisable to treat them prior to washing Blood treat fresh stains with cold water For dried stains soak overnight in water with a special detergent then rub in the soap and water ZANUSSI Oil based paint moisten with benzine stain remover lay the garment on a soft cloth and dab the stain treat several times Dried grease stains moisten with turpentine
28. ine to pause by pressing the button K The door can be opened immediately or after a few minutes depending on the model In any case do not try to open the door if it is locked If the door remains locked this means that the machine is already heating or that the water level is to high If you cannot open the door but you need to open it you have to switch the machine off by turning the selector dial to Off After a few minutes the door can be opened pay attention to the water level and temperature After this procedure it will be necessary to set the programme and the options again and then to press button KJ At the end of the programme The machine stops automatically Some acoustic signals sound The light of button KJ and the light EM go off the light illuminates and on the display will appear a flashing 8 42 The door can be opened If at the end of a programme there is water in the tub the light illuminates but the door remains locked to indicate that the water must be emptied out before opening the door To empty out the water proceed as follows 1 turn the programme selector dial to Off 2 select the Drain or Spin programme 3 reduce the spin speed if needed by pressing the relevant button 4 press the button Tl 5 at the end of programme only the pilot light illuminates Turn the programme selector dial to Off to switch the machine off Remove the laundry from the drum and carefully
29. laundry entered in the energy label in compliance on the inlet water temperature and on the with EEC 92 75 standards ambient temperature It refers to the highest temperature for each wash programme BQ Installation instruction Unpacking All transit bolts and packing must be removed before using the appliance You are advised to keep all transit devices so that they can be refitted if the machine ever has to be transported again 1 After removing all the packaging carefully lay machine on it s back to remove the polystyrene base from the bottom 2 Remove the power supply cable and the inlet and draining hose from the hose holders on the rear of the appliance 4 Slide out the relevant plastic spacers ZANUSSI 5 Open the porthole and remove the polystyrene block fitted on the door seal 6 Fill the smaller upper hole and the two large ones with the corresponding plastic plug caps supplied in the bag containing the instruction booklet Positioning Install the machine on a flat hard floor Make sure that air circulation around the machine is not impeded by carpets rugs etc Check that the machine does not touch the wall or other kitchen units Level the washer dryer by raising or lowering the feet The feet may be tight to adjust as they incorporate a self locking nut but the machine MUST be level and stable If necessary check the setting with a spirit level
30. lay the garment on a soft surface and dab the stain with the fingertips and a cotton cloth Rust oxalic acid dissolved in hot water or a rust removing product used cold Be careful with rust stains which are not recent since the cellulose structure will have already been damaged and the fabric tends to hole Mould stains treat with bleach rinse well whites and fast coloureds only Grass soap lightly and treat with bleach whites and fast coloureds only Ball point pen and glue moisten with acetone lay the garment on a soft cloth and dab the stain Lipstick moisten with acetone as above then treat stains with methylated spirits Remove any residual marks from white fabrics with bleach Red wine soak in water and detergent rinse and treat with acetic or citric acid then rinse Treat any residual marks with bleach Ink depending on the type of ink moisten the fabric first with acetone then with acetic acid treat any residual marks on white fabrics with bleach and then rinse thoroughly Tar stains first treat with stain remover methylated spirits or benzine then rub with detergent paste do not use acetone on artificial silk Detergents and additives Good washing results also depend on the choice of detergent and use of the correct quantities to avoid waste and protect the environment Although biodegradable detergents contain substances which in large quantities can upset the delicate bal
31. o avoid a too long drying time so saving energy In any case the reduction of the spin speed is only possible after selecting drying The lowest values you can select are the follow ing 900 r p m for cottons 700 r p m for synthetics 6 Start the programme by pressing the button After the programme has started the time remaining on the display is updated every minute 7 At the end of the programme the buzzer sounds Three flashing zeros 2 20 appear on the display At this point of the programme starts an anti crease phase which lasts about 10 minutes During this time the door is locked and the display keeps showing the flashing zeros 0 00 If you wish to open the door before or dur ing the anti crease phase please follow the instructions given in the previous chapter 7 Turn the selector dial to the Off position to switch the machine off 8 Remove the laundry 21 Care and cleaning IMPORTANT You must DISCONNECT the appliance from the electricity supply before you can carry out any cleaning or maintenance work Descaling The water we use normally contains lime It is a good idea to periodically use a water softening powder in the machine Do this separately from any laundry washing and according to the softening powder manufacturer s instructions This will help to prevent the formation of lime deposits Maintenance Wash With the use of low temperature washes it is po
32. posed by the washer dryer or to select the No spin or the Rinse Hold option The relevant light will light up e By pressing this button you can select only one of the following options Prewash Intensive Super Quick see the relevant chapter Functions e The relevant light will light up g Extra Rinse button HH Display GJ Start Pause button Drying Time button E Programme progress display ZANUSSI e By pressing this button the machine performs some additional rinses e The display shows the following information duration of the selected programme selected drying time incorrect option selection alarm codes heating phase child safety lock and end of programme e This button allows you to start the selected programme the corresponding green pilot light stops flashing e This button also interrupts a programme which is running the corresponding green pilot light starts to flash e By pressing this button you can select a timed programme for cotton or synthetics the relevant phase light illuminates e The different pilot lights illuminate during the different phases washing Wash E drying Dry H and at the end of the cycle End ER Display The display A shows the following information Duration of the selected programme After selecting a programme the duration of the selected programme appears on the dis play e g 2 25 During the programme the time r
33. power socket close the water tap if necessary wait until the water has cooled down open the pump door using a suitable tool place a bowl with a small edge close to the pump to collect any spillage Remove the emergency emptying cap from the filter cover The water should drain by gravity into the bowl When the bow is full put the cap back on filter cover Empty the bowl Repeat the procedure until water stops flowing out clean the pump if necessary as previously described replace the filter into the pump and screw it firmly as previously described replace the emergency emptying cap into the filter cover and close the pump door a ZANUSSI What to do if IMPORTANT Certain problems are due to lack of simple maintenance or oversights which can be solved easily without calling out an engineer Before contacting your local Service Centre please carry out the checks listed below During machine operation it is possible that the red pilot light of the button K flashes the buzzer sounds and one of the following alarm codes appears on the display to indicate that the machine is not working e 72 problem with the water supply e 28 problem with water draining e 4 door open Once the problem has been eliminated press the button E to restart the programme If after all checks the problem persists contact your local Service Centre The door has not been closed E40 Close the door firmly The plug
34. r connections after the installation e lf the appliance is installed in a location subject to frost please read the dangers of freezing chapter e Any plumbing work required to install this appliance should be carried out by a qualified plumber or competent person e Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person Use e This appliance is designed for domestic use It must not be used for purposes other than those for which it was designed e Only wash and dry fabrics which are designed to be machine washed and dried Follow the instructions on each garment label e Do not overload the appliance See the relevant section in the user manual e Before washing ensure that all pockets are empty and buttons and zips are fastened Avoid washing frayed or torn articles and treat stains such as paint ink rust and grass before washing Underwired bras must NOT be machine washed Garments which have been in contact with volatile petroleum products should not be machine washed If volatile cleaning fluids are used care should be taken to ensure that the fluid is removed from the garment before placing in the machine As some duvets and eiderdowns should be washed dried in large commercial machines because of their bulk please check with the manufacturer of the item before washing in a domestic machine The users should always check that they hav
35. rked with the symbol amp are recyclable gt PE lt polyethylene gt PS lt polystyrene gt PP lt polypropylene This means that they can be recycled by disposing of them properly in appropriate collection containers Old machine Use authorised disposal sites for your old appliance Help to keep your country tidy The symbol K on the product or on its packaging indicates that this product may not be treated as household waste Instead it should be taken over to the appropriate collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product For more detailed information about recycling of this product please contact your local council your household waste disposal service or the shop where you purchased the product ZANUSSI Ecological hints To save water energy and to help protect the environment we recommend that you follow these tips e Normally soiled laundry may be washed without prewashing in order to save detergent water and time the environment is protected too e The machine works more economically if it is fully loaded e With adequate pre treatment stains and limited soiling can be removed the laundry can then be washed at a lower temperature e Measure out
36. ssible to get a build up of residues inside the drum We recommend that a maintenance wash be performed on a regular basis To run a maintenance wash e The drum should be empty of laundry e Select the hottest cotton wash programme e Use a normal measure of detergent must be a powder with biological properties External cleaning Clean the exterior cabinet of the appliance with soap and water only and then dry thoroughly Cleaning the dispenser drawer The washing powder and additive dispenser drawer should be cleaned regularly 22 To aid cleaning the top part of the additive compartment should be removed Remove the drawer by pressing the catch downwards and by pulling it out Flush it out under a tap to remove any traces of accumulated powder Cleaning the drawer recess Having removed the drawer use a small brush to clean the recess ensuring that all washing powder residue is removed from the upper and lower part of the recess Replace the drawer and run the rinse programme without any clothes in the drum Cleaning the pump The pump should be inspected if e the machine does not empty and or spin e the machine makes an unusual noise during draining due to objects such as safety pins coins etc blocking the pump e a problem with water draining is detected see chapter What to do if for more details IMPORTANT Before opening the pump door switch the appliance off and
37. t illuminates The selected drying time appears on the display For Cottons you can select a drying time from 10 minutes to 250 minutes 4 72 For Synthetics it is possible to select a drying time from 10 minutes to 130 minutes 2 72 Every time you press the button the time increases by 5 mins Pilot Light s EJ When selecting the programmes depending on the programme selected the Wash ERI or the Dry m pilot light illuminates and stays on while the machine is working In any case both lights indicate that the appliance starts operating and the door is locked When the programme has finished the End ER pilot light illuminates and the other lights go off Programme table Programme Description of Spin red OW Main wash rinses White cotton L in at d Coron normally soiled cotton Prewash Intensive 019 SPin at max spee 90 items Super Quick Max Load 6 Kg ASE Reduced Load 3 Kg White and fast j Cottons coloured cotton Spin red i ee d 60 Eco normally soiled cotton Prewash Extra rinse Max Load 6 Kg items Spin red W Man wash rinses Cottons Coloured cotton Prewash Intensive Long spin at max speed 60 40 normally soiled Super Quick Max Load 6 Kg Bia iee Reduced Load 3 Kg 5 Main wash rinses Cottons Coloured cotton lightly Spin red 9 Long spin at max speed 40 Eco soiled Prewash Extra rinse Max Load 6 Kg Spin red W Man wash rinses Synthetics Synthetic or mix
38. t you to stretch the items rolled up out to redistribute evenly the laundry in the drum and to select an additional drying cycle of 20 30 minutes 12 ZANUSSI Programme information Eco programmes Wool and Handwash Silk Easy Iron Mini 30 Rinses Drain Spin Off Cancelling Switching off of the appliance This programme can be selected for slightly or normally soiled cotton items The temperature will decrease and the washing time will be extended This allows you to obtain a good washing efficiency whilst saving energy Washing programme for machine washable wool as well as for hand washable woollens and delicate fabrics with the hand washing care symbol v Delicate washing programme suitable for silk and mixed synthetics items Washing temperature is 30 C The maximum spin speed is automatically reduced to 700 rpm Selecting this programme the laundry is gently washed and spun to avoid any creasing In this way ironing is easier Furthermore the machine will perform additional rinses Special program at 30 C the duration is approx 30 minutes suitable for laundry to be freshened up e g a sport jacket worn only once or slightly soiled or new garments With this programme it is possible to rinse and spin cotton garments which have been washed by hand The machine performs 3 rinses followed by a final spin at maximum speed The spin speed can be reduced by depressing the button H For
39. tened so as to stop leaks and young children being able to remove it Cleaning the water inlet filter If your water is very hard or contains traces of lime deposit the water inlet filter may become clogged It is therefore a good idea to clean it from time to time 23 Care and cleaning Turn off the water tap Unscrew the water inlet hose Clean the filter using a hard bristle brush Tighten up the inlet hose The dangers of freezing If the machine is exposed to temperatures below 0 C certain precautions should be taken pull out the plug from the power socket turn off the water tap unscrew the inlet hose place a bowl with a small edge close to the pump to collect any spillage from the emergency emptying hose Place the end of the inlet hose in a bowl placed on the floor and let water drain out screw the water inlet hose back on and reposition the emergency emptying cap on again into the filter cover when you intend to start the machine up again make sure that the room temperature is above 0 C IMPORTANT Every time you drain the water you must pour 2 litres of water into the main wash compartment of the detergent drawer and then run the drain programme This will activate the ECO VALVE device avoiding that part of the detergent remains unused at next washing Emergency emptying out If the water is not discharged proceed as follows to empty out the machine pull out the plug from the
40. the correct levelling of the appliance The laundry is not evenly distributed in the drum e Redistribute the laundry Maybe there is too little laundry in the drum e Load more laundry The electronic unbalance detection device has cut in because the laundry is not evenly distributed in the drum The laundry is redistributed by reverse rotation of the drum This may happen several times before the unbalance disappears and normal spinning can resume If after 10 minutes the laundry is still not evenly distributed in the drum the machine will not spin In this case redistribute the load manually and select the spin programme e Redistribute the laundry The machine is fitted with a type of motor which makes a different noise compared with other traditional motors This new motor ensures a softer start and more even distribution of the laundry in the drum when spinning as well as increased stability of the machine 27 The machine does not dry or does not The drying time has not been selected dry properly Select the drying time The water tap is not turned on E1 Open the water tap The drain filter is clogged E20 Clean the drain filter The machine is overloaded e Reduce the laundry load The selected drying time was not suitable for the laundry e Select the suitable drying time for the laundry If you are unable to identify or solve the problem contact our service centre Before telephoning mak
41. ts do not climb into the drum To avoid that they remain Closed inside the drum the machine incorporates special feature To activate this device To disable this device rotate the button and restore the without pressing it possibility of closing the inside the door door rotate the button clockwise until the anti clockwise until the groove is horizontal If groove is vertical necessary use a coin ZANUSSI Description of the appliance 1 Detergent dispenser drawer H Control panel Door opening handle 4 Drain pump H Adjustable feet Detergent dispenser drawer Control panel and functions G O O CoC jC OO0000 Control Panel key symbols rrr E No spin option Rinse Hold option Child safety lock i Information The control panel is illustrated above It shows the programme selector dial as well as the different buttons the pilot lights and the display These are represented by relevant numbers which are explained in the table below Programme selector dial and On Off switch H Spin reduction button Options button e The programme selector dial allows you to select a programme and or to switch the machine on off It can be turned either clockwise or anticlockwise The light of button starts to flash e Press the Spin button repeatedly to change the spin speed if you want your laundry to be spun at a speed different from the one pro
42. x Load 2 Kg Main Wash rinses Short spin at 700 rom Max Load 2 5 Kg Main wash rinses Short spin at 700 rom Max Load 1 Kg 3 rinses Long spin at max speed Max Load 6 Kg Draining of water Drain and long spin 11 Drying Times Suggested Degree of drying Type of fabric Load Spin speed drying time mins 1600 rpm 130 150 4 kg 1400 rpm 140 160 1200 rpm 150 170 ee Dae 1600 rpm 75 85 otton and linen bathrobes bath towels a ene Boos Suitable for Be 1200 rpm 85 95 items to put away without 1600 rpm 35 45 ironing 1 5 kg 1400 rpm 40 50 1200 rpm 45 55 Synthetics and mixed fab 2 kg 900 rpm 70 80 rics jumpers blouses underwear household linen 1kg 900 rpm 35 45 1600 rpm 100 120 4kg 1400 rpm 110 130 1200 rpm 120 140 1600 rpm 60 70 Suitable Cotton and linen sheets 3k 1400 ia 65 75 for ironing tablecloths shirts etc g P 1200 rpm 70 80 1600 rpm 30 40 1 5 kg 1400 rpm 35 45 1200 rpm 40 50 In compliance with EC directive EN 50229 the cotton reference programme for the data entered in the Energy Label must be tested dividing the maximum washing load by two equal parts and drying with TIMED DRYING each of them NOTE The different type of cottons towelling sheets shirts and so on or eventual laundry rolling up during spinning phase may cause a not uniform dryness So in the exceptional case that at the end of the cycle the laundry remains slightly wet we sugges
Download Pdf Manuals
Related Search