Zanussi ZJD1219 Instruction Booklet
Contents
1. The hinges will be fixed to the door by means of screws for wood 2 Fig B supplied with the appliance c Mounting the door Fix the hinges 1 to the machine by means of the M5x8 screws 3 Fig B The hinges can be adjusted to compensate for possible uneven thickness of the door To align the door perfectly it is necessary to loosen the screw 3 Fig B adjust the door and tighten the screw again d Counter magnet 6 The appliance is pre arranged for a magnetic closure of the door To enable a correct operation of this device it is necessary to screw the counter magnet 6 steel disk rubber ring into the inner side of the door Its position must correspond to the magnet 4 on the appliance see picture D If the door has to be opened from left to right invert the position of the plates 7 the magnet 4 and the plate 5 Fig B and E Mount the countermagnet 6 and the hinges 1 as previously described Recommendations regarding the construction and fitting of a base when the installation requires an integrated appliance to be raised Where the appliance has been raised by mounting onto a wooden base provided by the installer The material used to construct the base should have a non slip surface be water repellent and if possible be one solid piece If it is not possible to use one solid piece due to the additional height required ensure that any additional strips of timber are glued an2. ZANUSSI WASHER DRYER ZJD 1219 INSTRUCTION BOOKLET A Important Safety Information It is most important that this instruction book should be retained with the appliance for future reference Should the appliance be sold or transferred to another owner or should you move house and leave the appliance always ensure that the book is supplied with the appliance in order that the new owner can get to know the functioning of the appliance and the relevant warnings These warnings have been provided in the interest of safety You MUST read them carefully before installing or using the appliance Installation This appliance is heavy Care should be taken when moving it It is dangerous to alter the specifications or attempt to modify this product in any way All packing and transit bolts must be removed before use Serious damage can occur to the product and to property if this is not adhered to See relevant section in instructions Any plumbing work required to install this appliance should be carried out by a qualified plumber or competent person Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person Care must be taken to ensure that the appliance does not stand on the electrical supply cable If the machine is situated on a carpeted floor please adjust the feet in order to allow air to circu
3. empty When replacing the filter ensure it is securely retightened so as to stop leaks and young children being able to remove it The water inlet filter If your water is very hard or contains traces of lime deposit the water inlet filter may become clogged It is therefore a good idea to clean it from time to time Turn off the water tap Unscrew the water inlet hose Clean the filter using a hard bristle brush Tighten up the inlet hose 21 The dangers of freezing If the machine is exposed to temperatures below 0 C certain precautions should be taken Turn off the water tap Unscrew the inlet hose Unhook the drain hose from the rear support and position the end of this hose and that of the inlet hose in a bowl Run the draining programme Disconnect the appliance Screw the inlet hose and reposition the drain hose When you intend to start the machine up again make sure that the room temperature is above 0 C Something Not Working Certain problems are due to lack of simple maintenance or oversights which can be solved easily without calling out an engineer Before contacting your local Service Force Centre please carry out the checks listed below IMPORTANT if you call out an engineer to a fault listed below or to repair a fault caused by incorrect use or installation a charge will be made even if the appliance is under guarantee During machine operation it is possible that the light of
4. upright standpipe should have a minimum length of 30cm 12 from the bottom of the elbow to the top of the pipe see diagram Make sure that it is designed in such a way that the end of the drain hose cannot be covered with water The drain hose may be extended to a maximum of 4 metres An additional drain hose and joining piece is available from your local Service Force Centre The joining piece must have an internal diameter of 18mm If you intend the drain hose to empty into a sink make sure that the sink is empty and the plug hole is not blocked Use the plastic U Piece supplied Important Before connecting up the machine to new pipework or to pipework that has not been used for some time run off a reasonable amount of water to flush out any debris that may have collected in the pipes Levelling Level the washer dryer by raising or lowering the feet The feet may be tight to adjust as they incorporate a self locking nut but the machine MUST be level and stable check diagonally Any necessary adjustment can be made with a spanner Accurate levelling prevents vibration noise and displacement of the machine during operation Some vibration is inevitable especially if mounted on a wooden floor Sprung wooden floors are particularly susceptible to vibration For advice consult a builder If possible always place the machine on a solid floor Special conditions If the floor is carpeted
5. PAUSE button the machine starts its hourly countdown To alter or cancel the preset delay press the START PAUSE button then press the DELAY START button until the required time is displayed or if you wish to cancel the delay until the symbol is displayed Then press the START PAUSE button again When the delay is cancelled the display shows the duration of the wash programme previously selected lI Display The display shows the following information Cancelling Duration of the programme Drying time Delayed start Incorrect option selection Alarm code End of programme Cancelling If a programme has been cancelled programme selector dial on position O three flashing dashes appear on the display Now you can select a new programme Duration of the selected programme After selecting a programme the duration is displayed in hours and minutes for example 2 5 The duration is calculated automatically on the basis of the maximum recommended load for each type of fabric After the programme has started the time remaining is updated every minute Drying time The selected drying time is displayed in minutes After starting the programme the remaining time is updated every minute Delayed start The selected delay 24 hours max set by means of the relevant button appears on the display for 3 seconds then the duration of the previously selected programme i
6. Programme progress display By selecting the wash programme the pilot lights corresponding to the various phases making up the programme come on After the machine has started only the running phase pilot light stays on When the programme has finished the END pilot light comes on O Door Q PREWASH Q wasH Q RINSES Q DRAIN O sPIN O pry O END The DOOR light indicates if the door can be opened Light on the machine is functioning but the door can be opened see page 10 Light off the door can be opened at the end of the cycle or cannot be opened because the machine is functioning Light blinking the machine is in PAUSE and the door cannot be opened 14 Programme selector dial The selector is divided into 5 sections Cotton Synthetics Delicates Wool 2 hand washing Special programmes Reset programme O The selector dial can be turned either clockwise or anticlockwise Position E corresponds to the ENERGY SAVING programme and position to cold wash Position Sy corresponds to the drying programme At the end of the programme the selector dial must be turned to position O reset Functions End of programme When the door locked light has gone out the door can be opened The END light on the programme progress display illuminates Turn the programme selector dial to O Switch the machine off and remove the laundry Altering a programme You can alter the p
7. Your telephone number 3 Clear and concise details of fault 4 The model and serial number of the appliance found on the rating plate see picture 5 The purchase date using very little water without affecting performance The drying time has not been selected The water tap is not turned on E10 The drain filter is clogged E20 The machine is overloaded The selected drying time or drying sector is not suitable for the laundry 23 Customer Care For general enquiries concerning your Zanussi appliance or for further information on Zanussi products please contact our Customer Care Department by letter or telephone at the address below or visit our website at WWNW Zanussi co uk Customer Care Department Zanussi 55 77 High Street Slough Berkshire SL1 1DZ Tel 08705 727727 calls to this number may be recorded for training purposes Guarantee Conditions Standard guarantee conditions We Zanussi undertake that if within 24 months of the date of the purchase this Zanussi appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials we will at our option repair or replace the same FREE OF ANY CHARGE for labour materials or carriage on condition that The appliance has been correctly installed and used only on the electricity supply stated on the rating plate The appliance has been used for normal domestic purposes only and in a
8. appliance should be carried out by a qualified Any plumbing work required to install this appliance should be carried out by a qualified Technical Specifications DIMENSIONS Height 82 cm 32 3 Width 60 cm 23 6 Depth 54 cm 21 2 POWER SUPPLY VOLTAGE 230 240 V 50 Hz TOTAL POWER ABSORBED 2050 W 10A WATER PRESSURE Minimum 50 kPa Maximum 800 kPa MAX LOAD CAPACITY Washing Cotton linen 4 5 kg 10 lbs Synthetics 2 kg 4 5 lbs Delicate fabrics 2 kg 4 5 lbs Wool 1 kg 2 2 lbs Drying Cotton linen 2 25 kg 5 lbs Synthetics 1 5 kg 3 3 lbs SPIN SPEED Maximum 1200 rpm CONSUMPTION DATA FOR WASHING Energy 0 90 kWh 4 5 KG NORMALLY SOILED COTTON Water 40 litres ITEMS AT 60 C WITH COLD Time 132 mins WATER FILLING C This appliance complies with the following E E C Directives 73 23 EEC of 19 2 73 Low Voltage Directive and subsequent modifications 89 336 EEC of 3 5 89 Electromagnetic Compatibility Directive and subsequent modifications 27 Unpacking A You are advised to keep all the packaging for re use in case the machine is to be transported again All transit bolts and packing must be removed before using the appliance Using a spanner unscrew and remove the rear right bolt Lay the machine gently on its back making sure that the hoses are not squashed Remove the polystyrene base and take off the bottom panel by unscrewing the central screw Carefully slide out
9. detergent consumption Even small loads are washed economically because the amount of water used is regulated automatically according to the load and type of fabric Automatic cooling of the wash water to 60 C before draining with the 95 C programme This reduces thermal shock to fabrics helping to prevent creasing The special wool programme with its new delicate wash system treats your woollens with extreme care The anti unbalance device ensures that the washing machine remains stable when spinning The two drying programmes will give your wash that soft relaxed feel whatever the weather Ecological hints To save water and energy and help protect the environment we recommend that you follow these hints Adjust the quantity of detergent according to the hardness of your water supply the amount of laundry and the degree of soiling Select an economy programme for lightly soiled laundry A programme without prewash is sufficient for normally soiled laundry The machine works more economically if it is fully loaded both for washing and drying cycles With adequate pre treatment stains and limited soiling can be removed the laundry can then be washed at a lower temperature Always load well spun laundry The higher the spin speed the lower the electricity consumption and the shorter the drying times important Your machine is fitted with a balance control device which ensures the machine is stable
10. s largest producer of powered appliances for kitchen cleaning and outdoor use More than 55 million Electrolux Group products such as refrigerators cookers washing machines vacuum cleaners chain saws and lawn mowers are sold each year to a value of approx USD 14 billion in more than 150 countries around the world Electrolux Household Appliances Limited 2001
11. the START PAUSE button flashes and an alarm code appears on the display E10 problem with the water supply E20 problem with water draining E40 door open Once the problem has been eliminated press the START PAUSE button to restart the programme If after all checks the problem persists contact your local Service Force Centre Symptom Possible causes The machine does not start The door has not been closed E40 The plug is not properly inserted in the power socket There is no current at the socket The main fuse or the fuse in the plug has blown The selector dial is not correctly positioned The START PAUSE button has not been depressed The DELAY START option has been selected The machine does not fill Ensure the water tap is open E10 The filter in the inlet hose is blocked E10 The inlet hose may be squashed or kinked E10 The door has not been closed EA0 The end of the drain hose is too low The end of the drain hose is submerged in water There is no vent in the end of the drain hose The drain hose may be squashed or kinked E20 The RINSE HOLD or NO SPIN option has been selected The drain filter may be blocked E20 The drain hose extension 1s not correct Follow the instructions for connecting to the waste The drainage system pipes are blocked E20 The wash load is unbalanced redistribute the clothes inside the drum to allow the machine to spin The machine fills then empti
12. 40 Cold X Wool coloureds Coloureds Economy Non fast coloureds Synthetics Delicates Programme description Wash at 95 C 3 rinses Normal spin Wash at 60 C 3 rinses Normal spin Wash at 60 C 3 rinses Normal spin Wash at 40 C 3 rinses Normal spin Wash at 30 40 3 rinses Normal spin Wash at 60 C 3 rinses Delicate spin Wash at 40 C 3 rinses Delicate spin Wash at 30 40 C 3 rinses Delicate spin Wash at 30 40 C 3 rinses Delicate spin Wash at 30 40 C or cold wash 3 rinses Delicate spin Additional functions SPIN SPEED RINSE HOLD PREWASH INTENSIVE QUICK EXTRA RINSE SPIN SPEED RINSE HOLD PREWASH EXTRA RINSE SPIN SPEED RINSE HOLD PREWASH INTENSIVE QUICK EXTRA RINSE SPIN SPEED RINSE HOLD PREWASH EXTRA RINSE SPIN SPEED RINSE HOLD PREWASH EXTRA RINSE INTENSIVE QUICK SPIN SPEED RINSE HOLD PREWASH EXTRA RINSE INTENSIVE QUICK SPIN SPEED PREWASH RINSE HOLD EXTRA RINSE SPIN SPEED RINSE HOLD PREWASH EXTRA RINSE INTENSIVE QUICK SPIN SPEED QUICK PREWASH RINSE HOLD EXTRA RINSE SPIN SPEED RINSE HOLD Energy kWh Consumption Water It 139 132 137 130 89 94 81 55 The coloured cotton programme at 60 C is the reference programme for the data entered in the energy label in compliance with EC 92 75 standards This data is given purely as an indication the consumption values may vary i
13. 5 40 The STORE DRY drying programme for cotton is the reference programme for the Energy Label data in compliance with EC directive 92 75 19 Maintenance and Cleaning and dryingBefore any maintenance or cleaning is carried out you must DISCONNECT the appliance from the electricity supply Descaling The water we use normally contains lime It is a good idea to periodically use a water softening powder in the machine Do this separately from any laundry washing and according to the softening powder manufacturer s instructions This will help to prevent the formation of lime deposits After each wash Leave the door open for a while This helps to prevent mould and stagnant smells forming inside the appliance Keeping the door open after a wash will also help to preserve the door seal Maintenance Wash With the use of low temperature washes it is possible to get a build up of residues inside the drum We recommend that a maintenance wash be performed on a regular basis To run a maintenance wash The drum should be empty of laundry Select the hottest cotton wash programme Use anormal measure of detergent must be a powder such as Ariel Futur External cleaning Clean the exterior cabinet of the appliance with soap and water only and then dry thoroughly Cleaning the dispenser drawer The washing powder and additive dispenser drawer should be cleaned regularly Remove the drawer by pressin
14. Road likeston DE7 5EP M pD S LEICESTER Unit 7 Oaks Industrial Estate Coventry Road Narborough Leicestershire LE9 5GF LINCOLN Unit 8 Clifton Street Stone Field Park Lincoln LN5 8LQ NEWCASTLE UNDER LYME 18 21 Croft Road Brampton Ind Estate Newcastle under Lyme Staffordshire ST5 OTW REDDITCH 13 Thornhill Road North Moons Moat Redditch Worcestershire B98 9ND TAMWORTH Unit 3 Sterling Park Claymore Tamworth B77 5DQ WORCESTER Units 1 amp 2 Northbrooks Close Gregorys Mill Ind Estate Worcester WR3 8BP LONDON amp EAST ANGLIA BECKENHAM 11a Gardner Ind Estate Kent House Lane Beckenham Kent BR3 1QZ CHELMSFORD Hanbury Road Widford Ind Estate Chelmsford Essex CM12 3AE COLINDALE Unit 14 Capitol Park Capitol Way Colindale London NW9 0EQ ELTHAM 194 Court Road Mottingham Eltham London SE9 4EW ENFIELD 284 Alma Road Enfield London EN3 7BB GRAVESEND Unit B4 Imperial Business Estate West Mill Gravesend Kent DA11 ODL IPSWICH Unit 6C Elton Park Business Centre Hadleigh Road Ipswich IP2 ODD LETCHWORTH 16 17 Woodside Ind Park Works Road Letchworth Herts SG6 1LA LONDON 2 4 Royal Lane Yiewsley West Drayton Middlesex UB7 8DL MAIDENHEAD Reform Road Maidenhead Berkshire SL6 8BY MOLESEY 10 Island Farm Avenue West Molesey Surrey KT8 2UZ NEWBURY 9 Pipers Court Berkshire Drive Thatcha
15. To be selected for extremely delicate items 6 Rinse Hold button When RINSE HOLD option is selected the last rinse water is not emptied out to prevent the fabrics from creasing When the programme has finished the pilot light of the START PAUSE button flashes to indicate that the water must be emptied out To empty out water there are 3 possibilities Select programme by draining The water is emptied out without spinning Attention Before selecting programme by the selector dial has to be positioned on O cancelling Depress START PAUSE button after emptying the machine performs the spin cycle corresponding to the type of fabric previously selected Select the spin speed by means of the relevant button and then depress the START PAUSE button The machine empties itself after 18 hours if no action is taken The RINSE HOLD option CANNOT be selected for the automatic Washing amp Drying programme 7 Extra Rinse button Can be used with all programmes except the wool programme The machine performs 4 rinses instead of 3 This option is recommended for people who are allergic to detergents and in areas where the water is very soft 8 Soil level By depressing this button it is possible to select a programme more or less intensive according to the soil level of your laundry The corresponding pilot light comes on Intensive For heavy soiled laundry The washing phase will be prolonged by about 10 minutes I
16. all items such as socks laces washable belts etc in a washing bag or pillow case as it 1s possible for such items to slip down between the tub and the inner drum Only use the advised quantities of fabric softener Damage to the fabric can ensue if you over fill Refer to the manufacturer s recommendations of quantities As some duvets and eiderdowns should be washed in large commercial machines because of their bulk please check with the manufacturer of the item before washing in a domestic machine Never tumble dry items that have had contact with chemicals such as dry cleaning fluid These are of a volatile nature and could cause an explosion Only tumble dry items which have been washed in water or require airing Plastic detergent dispensers should not remain in the drum during the drying cycle as the plastic used is not designed to withstand the heat If you wish to wash through to dry you should use the conventional detergent dispenser drawer Leave the porthole door slightly ajar between washes to preserve the door seal Under no circumstances should you attempt to repair the machine yourself Repairs carried out by Inexperienced persons may cause injury or serious malfunctioning Contact your local Zanussi Service Force Centre Always insist on genuine Zanussi Spare parts Contents For the User Important Safety Information Your New Washer Dryer Description of the Appliance Detergent dispenser drawer The Co
17. and towel 100 150 g Towelling hand towel 150 250 g Towelling bath towel 700 1000 g Bath robe 1000 1500 g Man s shirt 200 300 g Apron 150 200 g Load the laundry loosely alternating large items with small ones Sort the laundry according to the type of fabric colour fastness and how dirty it is Avoid washing unhemmed or torn items as they may unravel m Before washing empty all pockets of small objects which may have been left inside coins keys screws etc as these could damage the drain pump m When washing curtains remove the hooks m Close poppers and zips and fasten loose buttons m It is essential to wash new coloured items separately when washing for the first time m When washing fabrics requiring different wash temperatures together always select the lowest temperature m White items should not be washed with coloured items m Very small items handkerchiefs ribbons socks etc should be washed in a washing bag or a pillow case W Use a good quality detergent suitable for automatic washing machines m Use the correct quantities of detergent m For wool use gentle detergent only in small quantities m Bleach is very corrosive it should be used with care and kept out of reach of children 14 Some stains such as fruit wine grass rust etc are difficult to remove and should be treated before washing with specific products which can be found in most household shops In some cases it may hel
18. be accessible Permanent connection In the case of permanent connection it is necessary that you install a double pole switch between the appliance and the electricity supply mains with a minimum gap of 3mm between the switch contacts and of a type suitable for the required load in compliance with the current electrical regulations The switch must not break the yellow and green earth cable at any point Building in This appliance has been designed to be built into the kitchen furniture The recess should have the dimensions shown in picture Preparation and assembly of the door The machine is originally pre arranged for the assembly of a door opening from right to left In this case it is sufficient to screw in the hinges 1 and the counter magnet 6 provided with the appliance at the right level Fig B a Door The dimensions of the door should be width 595 598 mm thickness 16 22 mm The height C Fig C depends on the height of the adjacent furniture s base 35 12 5 14 depth b Hinges To mount the hinges it is necessary to drill two holes dia 35 mm depth 12 5 14 mm depending on the depth of door furniture on the inner side of the door The distance between the holes hobs fixing centres must be 32 416 mm The distance B from upper edge of the door to the centre of the hole depends on the adjacent furniture s dimensions The required dimensions are given in the picture C
19. button Press this button to switch the machine on Press it again to switch the machine off Programme Option buttons Depending on the programme different functions can be combined These must be selected after choosing the desired programme and before depressing the START PAUSE button When these buttons are pressed the corresponding pilot lights come on When they are pressed again the pilot lights go out If an incorrect option is selected the corresponding pilot light flashes for about 2 seconds and the message Err is displayed 4 Prewash button The machine performs a prewash cycle at 30 C max The prewash cycle ends with a short spin at 650 rp m in programmes for Cotton and Synthetics and with emptying of the water for Delicates This option is not available with the wool programme For use when washing heavily soiled laundry 5 Spin Speed button Press this button to reduce the maximum speed of the final speed proposed by the machine for the selected programme or to select position NO SPIN The light corresponding to the selected option illuminates Spin speed The following speeds are available for the different fabrics Cotton linen 500 700 900 max 1200 r p m Synthetics wool 500 700 max 900 r p m Delicates 500 max 700 r p m No Spin By selecting this option the spinning phases are suppressed This function is not available for cotton and linen
20. ccordance with the manufacturer s instructions The appliance has not been serviced maintained repaired taken apart or tampered with by any person not authorised by us All service work under this guarantee must be undertaken by an Zanussi Service Force Centre Any appliance or defective part replaced shall become the Company s property This guarantee is in addition to your statutory and other legal rights Home visits are made between 8 30am and 5 30pm Monday to Friday Visits may be available outside these hours in which case a premium will be charged 24 Exclusions This guarantee does not cover e Damage or calls resulting from transportation improper use or neglect the replacement of any light bulbs or removable parts of glass or plastic Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside the United Kingdom Appliances found to be in use within a commercial environment plus those which are subject to rental agreements Products of Zanussi manufacture which are NOT marketed by Zanussi European guarantee If you should move to another country within Europe then your guarantee moves with you to your new home subject to the following qualifications The guarantee starts from the date you first purchased your product e The guarantee is for the same period and to the same extent for labour and parts as exists in the new
21. country of use for this brand or range of products The guarantee relates to you and cannot be transferred to another user Your new home is within the European Community EC or European Free Trade Area The product is installed and used in accordance with our instructions and is only used domestically i e a normal household The product is installed taking into account regulations in your new country Before you move please contact your nearest Customer Care Centre listed below to give them details of your new home They will then ensure that the local Service Organisation is aware of your move and able to look after you and your appliances France Senlis 33 0 344 62 22 22 Germany Nurnberg 49 0 911 323 2600 Italy Pordenone 39 0 1678 47053 Sweden Stockholm 46 0 20 78 77 50 UK Slough 44 0 1753 219897 SERVICESFORCE To contact your local Service Force Centre telephone 08705 929 929 CHANNEL ISLANDS GUERNSEY JERSEY Guernsey Electricity PO Box 4 Vale Guernsey Channel Islands GY1 3AD Jersey Electricity Company Haut De L orme Rue De Haut De L orme Trinity Jersey Channel Islands JE3 5FG SCOTLAND ABERDEEN AUCHTERMUCHTY BLANTYRE 54 Claremont Street Aberdeen AB106RA 33a Burnside Auchtermuchty Fife KY14 7AJ Unit 5 Block 2 Auchenraith Ind Estate Rosendale Way Blantyre G72 0NJ ISLE OF LEWIS ORKNEY PERTH OWN SALES ND Macleod 16 James St
22. ct recommandations as to the amount of detergent that should be used for any one wash Therefore we recommend that you use approximately 1 3 less than the detergent manufacturer recommends on the packet or bottle making the appropriate allowances for soft or hard water and light or heavy soilage of clothes If you have judged the amount correctly you should expect to see a soft sudsy liquid during the wash It is not necessary to have a head of lather on the water 11 3 Measure out the fabric softener If required pour fabric softener into the compartment marked amp the amount used must not exceed the MAX mark in the drawer Close the drawer gently 4 Switch the machine on To switch the machine on press the ON OFF button the mains on light comes on ON OFF If the programme selector dial is on the Reset O position three flashing dashes will be displayed If the programme selector dial is positioned on a wash programme a flashing zero appears on the display 5 Select the required programme Turn the programme selector dial to the desired position the lights corresponding to the different phases making up the selected programme light on O poor O PREWASH O wasH Q RINSES O DRAIN O sPIN O pry Q EnD The display shows the duration of the programme 6 Select the SPIN SPEED or NO SPIN option Depress the SPIN SPEED button to choose the required speed or NO SPIN option the correspond
23. d Cardiff CF2 2QS Unit 6 7 Coed Parc Abergele Road Rhuddlan Clwyd LL18 5UG Unit 9 St Clears Business Park Tenby Road St Clears Carmarthen SA33 4JW Plas Ffynnon Warehouse Middleton Road Oswestry SY11 2PP LEEDS NEWTON AYCLIFFE SHEFFIELD 64 66 Cross Gates Road Cross Gates Leeds LS157YS Unit 23 Northfield Way Aycliffe Industrial Park Newton Aycliffe DL5 6EJ Pennine House Roman Ridge Road Sheffield S9 1GB NORTH WEST BIRKENHEAD CARLISLE ISLE OF MAN BOLTON PRESTON STOCKPORT 1 Kelvin Park Dock Road Birkenhead CH41 1LT Unit 7 James Street Workshops James Street Carlisle Cumbria CA2 5AH South Quay Ind Estate Douglas Isle of Man IM1 5AT Unit B Central Industrial Estate St Marks Street Bolton BL3 6NR Unit 250 Dawson Place Bamber Bridge Preston Lancashire PR5 8AL Unit 20 Haigh Park Haigh Avenue Stockport SK4 1QR 25 SERVICESFORCE To contact your local Service Force Centre telephone 08705 929 929 MIDLANDS 66 Birch Road East Wyrley Trading Estate Witton Birmingham B6 7DB BIRMINGHAM BOURNE Pinfold Road Bourne PE10 9HT BRIDGNORTH 68 St Mary s Street Bridgnorth Shropshire WV16 4DR GLOUCESTER 101 Rycroft Street Gloucester GL1 4NB HEREFORD Units 3 amp 4 Bank Buildings Cattle market Hareford HE4 9HX HIGHAM FERRERS 30 High Street Higham Ferrers Northants NN10 8PL ILKESTON Unit 2 Furnace
24. d screwed to the underside of the base see Fig F 5 mm Hardwood strip w Additional pieces of timber should run d from front to back mm k 00 mm lt 600 605mm Front view Drill four fixing holes see Fig G T 600 605 mm x 5 o Front edge Top view Position the base into the recess with its front edge as far forward as the adjoining plinth line will allow The reason for placing the base in this position is to allow a small strip of beading to be fitted in front of the appliance feet 33 Fix the base firmly to the floor using four appropriate countersunk screws see Fig H Hardwood strip 5mmx25mm With the appliance installed adjust all four feet ensuring the machine is stable and a clearance of approximately 5 mm is left between the top of the machine and the underside of the worktop A final check for stability should be carried out with the machine on spin with a load this will identify the need for any further fine adjustment to the feet A strip of beading approximately 605 mm W x 5 mm H x 25 mm D must be screwed down into the base directly in front of the machine s feet this will provide additional security If required an additional door magnet part number 1242394 00 3 and disc part number 1242393 00 5 are available from spare parts 2 From the Electrolux Group The world s No 1 choice The Electrolux Group is the world
25. during the spin If the wash load appears not to have been spun sufficiently at the end of the wash cycle because it is not evenly distributed in the drum the balance control device may have operated It will therefore be necessary to redistribute the wash load manually and select a spin programme For more detailed information see the section headed Something Not Working In the interest of the environment Materials marked with the symbol 5 are recyclable Check with your local Council or Environmental Health Office to see if there are facilities in your area for re cycling this appliance When the appliance is to be scrapped cut off the power supply cable and make the door lock device unusable to prevent young children from being trapped inside e Help to keep your country tidy use authorised disposal sites for your old appliance How do we help to protect the environment We use recycled paper Description of the 1 Detergent dispenser drawer 2 Programme guide 3 Control panel 4 Door opening handle 5 Filter 6 Adjustable feet Detergent dispenser drawer LI Prewash UIL Main wash e Fabric softener The Control Panel JETSYSTEM 1 2 3 Detergent dispenser drawer 2 Mains on light This light comes on when the ON OFF button is pressed and goes out when it is pressed again 3 ONJOFF
26. e the electricity supply voltage is the same as that indicated on the appliance s rating plate The rating plate is located at the top of the rim of the open door Ser No The appliance is supplied with a 13amp plug fitted In the event of having to change the fuse in the plug supplied a 13amp ASTA approved BS1363 A fuse must be used Should the plug need to be replaced for any reason proceed as described below The wires in the mains lead are coloured in accordance with the following code Green and Yellow Earth Blue Neutral Brown Live GREEN amp YELLOW BROWN CORD CLAMP The wire coloured green and yellow must be connected to the terminal marked with the letter E or by the earth symbol or coloured green and yellow The wire coloured blue must be connected to the terminal N or coloured black 31 The wire coloured brown must be connected to the terminal marked L or coloured red Upon completion there must be no cut or stray strands of wire present and the cord clamp must be secure over the outer sheath WARNING A cut off plug inserted into a 13 amp socket is a serious safety shock hazard Ensure that the cut off plug is disposed of safely Should the appliance power supply cable neeed to be replaced this should be carried out by our Service Force Centre Note When the appliance is installed the power supply cable must
27. es immediately The machine does not empty and or does not spin There is water on the floor Too much detergent or unsuitable detergent has been used creates too much foam Check whether there are any leaks from one of the inlet hose fittings It is not always easy to see this as the water runs down the hose check to see if it is damp The drain hose may be damaged or not securely positioned The detergent dispenser drawer or recess is clogged The drainage system pipes are blocked Unsatisfactory washing results Too little detergent or unsuitable detergent has been used An insufficient amount of detergent leaves the laundry looking grey and causes lime scale to form Stubborn stains have not been treated prior to washing The correct wash programme has not been selected Too much laundry has been placed in the drum 22 Symptom Possible causes The machine vibrates when spinning The internal packing has not been removed The machine is in contact with the wall or furniture The machine is not level The washing load is badly distributed in the drum Maybe there is very little laundry in the drum The door will not open The water level is above the bottom edge of the door The machine is heating the water or drying the clothes The drum is turning Spinning starts late or the machine does not spin The electronic unbalance detection device has cut in becau
28. g the catch downwards and by pulling it out Flush it out under a tap to remove any traces of accumulated powder 20 To aid cleaning the top part of the additive compartment should be removed Cleaning the drawer recess Having removed the drawer use a small brush to clean the recess ensuring that all washing powder residue is removed from the upper and lower part of the recess Replace the drawer and run the rinse programme without any clothes in the drum Cleaning the filter The water drain filter A clean filter is important for the correct functioning of the machine and should therefore be cleaned after every washing and drying programme Place a container under the filter to catch any spillage If the filter is blocked and the machine is unable to drain you will need to drain the water manually from the machine at this stage To do this unhook the drain hose from the standpipe or sink and hold the end of the hose over a bowl on the floor The water should drain by gravity into the bowl When the bowl is full hook the hose back up and empty the bowl Repeat the procedure until water stops flowing out Unscrew and remove the filter Clean carefully under a fast running tap A Warning When the appliance is in use and depending on the programme selected there can be hot water in the filter Never remove the filter during a wash cycle always wait until the appliance has finished the cycle and is
29. hose to a tap with a 3 4 thread Installation should comply with local water authority and building regulations requirements The appliance must be connected to a cold water supply A minimum water pressure of 50kPa 0 5 bar is required for safe operation of the appliance If you cannot make the cold water connection direct from the rising mains you may be able to operate the appliance from your cold water storage system There should be a minimum distance of 5 02m 16 5 ft between the appliance s inlet and the bottom of the water storage tank Set the hoses correctly by loosening the ring nuts After positioning the inlet hoses be sure to tighten the ring nuts again to prevent leaks Water drainage This appliance is designed to be permanently plumbed into your home s water supply and drainage system Max 90 cm 35 4 23 6 Min 60 cmt The appliance drain hose should hook into a standpipe the hook in the drain hose is formed using the plastic U Piece supplied 29 The standpipe should have an internal diameter of approximately 38mm see diagram thus ensuring there is an air break between the drain hose and standpipe 38 mm 1 2 diameter standpipe a E o 9 e When discharging into a standpipe ensure that the top of the curve in the hose end is no more than 90cm 35 4 and no less than 60cm 23 6 above floor level The
30. ing light comes on 1200 O 900 O 700 O 500 O NO SPIN Oo SPIN SPEED O 7 Select the required options The light corresponding to the depressed button illuminates INTENSIVE CE NORMAL I l l l quick O l l l RINSE EXTRA SOIL HOLD RINSE LEVEL OOOO PREWASH 8 Select the Delay Start option To delay starting of a programme press the DELAY START button The corresponding light illuminates The figures corresponding to the selected delay will be displayed for about 3 seconds after which the duration of the selected programme will appear on the display When the START PAUSE button is pressed the selected delay will again appear on the display and the machine starts its countdown During this period it is possible to load other laundry press the START PAUSE button Open the door Load the laundry Close the door and press the START PAUSE button again 9 Start the programme To start the selected programme press the START PAUSE button the corresponding light stops flashing The pilot light corresponding to the wash phase which is running is on The machine starts operating O START PAUSE Q If the Delay Start option has been selected the programme will start at the end of the countdown 10 At the end of the programme The machine stops automatically If the RINSE HOLD option has been selected the light of the START PAUSE button flashes to indicate that the water mu
31. late freely Child Safety This appliance is designed to be operated by adults Children should not be allowed to tamper with the controls or play with the product Pets and children have been known to climb into washing machines Please check your drum before use The glass door becomes very hot during the washing and drying cycle Keep children away from the vicinity of the appliance whilst it is in operation e Keep all packaging well away from children e Keep all detergents in a safe place out of children s reach Use Always unplug the appliance and turn off the water supply after use Do not overload the appliance See relevant section in the instruction book Only wash fabrics which are designed to be machine washed If in doubt consult the care label on the clothes Before washing ensure that all pockets are empty and buttons and zips are fastened Avoid washing frayed or torn articles and treat stains such as paint Ink rust and grass before washing Underwired bras must NOT be machine washed Any objects such as coins safety pins nails screws stones or any other hard sharp material can cause extensive damage and must not be placed into the machine Garments which have been in contact with volatile petroleum products should not be machine washed If volatile cleaning fluids are used care should be taken to ensure that the fluid is removed from the garment before placing in the machine Wash sm
32. m Berkshire RG19 4ER NORWICH 2b Trafalgar Street Norwich NR1 3HN SUNBURY Unit 1a The Summit Hanworth Road Sunbury on Thames TW16 5DB 26 SOUTH EAST ASHFORD FLEET Unit 2 Bridge Road Business Centr Bridge Road Ashford Kent TN23 1BB Unit 1 Redfields Ind Estate Church Crookham Fleet Hampshire GU13 ORD HAYWARDS HEATH TONBRIDGE 21 25 Bridge Road Haywards Heath Sussex RH16 1UA Unit 30 Deacon Trading Estate Morley Road Tonbridge TN9 1RA SOUTH WEST BARNSTAPLE Main Road Fremington Barnstaple North Devon EX31 2NT BOURNEMOUTH BRIDGEWATER BRISTOL EMSWORTH 63 65 Curzon Road Bournemouth Dorset BH14PW 6 Herswell Business Park Salmon Parade Bridgwater Somerset TA6 5PY 11 Eldon Way Eldonwall Trading Estate Bristol BS4 3QQ 266 Main Road Southbourne Emsworth PO10 8JL ISLE OF WIGHT NEWTON ABBOT REDRUTH Unit 8 Enterprise Court Ryde Business Park Ryde Isle of Wight PO33 1DB Unit 2 Zealley Ind Estate Kingsteignton Newton Abbot TQ123TD Unit 7D Pool Ind Estate Druids Road Redruth Cornwall TR15 3RH Installation Instructions electrician or competent person gt BRE plumber or competent person It is dangerous to alter the specifications or attempt to modify this product in any way Care must be taken to ensure that the appliance does not stand on the electrical supply cable Any electrical work required to install this
33. n relation to the quantity and type of laundry the temperature of the water supply and the ambient temperature The data refers to the highest temperature for each programme 17 Special Programmes Selector d Consumption dial Programme description Additional ors 3 position functions load Energy Water Time kWh It min Soak at 30 C 19 20 stop with water in tub To drain depress START PAUSE button The machine automatically empties itself after 18 hours 3 rinses with liquid additive SPIN SPED 58 i RINSE HOLD aN EXTRA RINSE Spin 1 rinse with softener SPIN SPEED 25 Spin RINSE HOLD ha 3 spin SPIN SPEED 10 j Mini Wash at 30 C SPIN SPEED l 30 programme 2 rinses RINSE HOLD Spin at 700 r p m O For cancelling the wash programme which is running This data is given purely as an indication the consumption values may vary in relation to the quantity and type of laundry the temperature of the water supply and the ambient temperature 18 Drying Programmes Degree of drying Type of fabric Spin speed iod I 1200 95 105 Mare bathrobes bath NICHE towels etc materials APT 1 kg 1200 55 65 1200 85 95 towels T shirts Sic pees 1 kg 1200 45 55 Suitable for items to put away without ironing Synthetics and mixed 90 100 fabrics jumpers blouses underwear household linen 55 65 Tron dry Cotton and linen ad Suitable for sheets tablecloths ironi hirts etc ironing shirts etc 3
34. ntrol Panel Operating sequence Washing only Load the laundry Measure out the detergent Jetsystem wash Measure out the fabric softener Switch the machine on Select the required programme Select the SPIN SPEED or NO SPIN option Select the required options Select the delay start Start the programme At the end of the programme Drying only Automatic washing and drying Washing and Drying Hints Which detergent And in which form Wash Care Symbols Washing and Special Programmes Drying Programmes Maintenance and Cleaning Descaling After each wash Maintenance wash External cleaning Cleaning the dispenser drawer Cleaning the drawer recess Cleaning the filter The dangers of freezing Something Not Working Service and Spare Parts Guarantee conditions Service Force Centres 24 25 26 For the Installer Installation Instructions 27 Technical Specifications 27 Unpacking 28 Positioning 28 Water inlet 29 Water drainage 29 Levelling 30 Special conditions 30 In the interest of the environment 30 Electrical connection 31 Building in 32 33 Guide to use the Instruction Book The following symbols will be found in the text to guide you throughout the instructions A Safety instructions G Hints and tips W Environmental information i Your New Washer Dryer Your new washer dryer fitted with the Zanussi JET SYSTEM meets all modern requirements for effective treatment of laundry with low water energy and
35. nts You can reduce the speed by means of SPIN SPEED button to adapt it to the fabrics to be spun i Miniprogramme This is a complete programme that can be combined with the following options SPIN SPEED NO SPIN RINSE HOLD and DELAY START To be used for laundry which is lightly soiled or which needs freshening up Max load 2 kg Washing temperature 30 C Programme duration 30 minutes Final spin speed 700 r p m O Cancelling To reset a programme turn the selector dial to O Now can a new programme be selected Operating Sequence Washing only Before the first wash we recommend that you run a cotton cycle at 60 C without any laundry in the machine to remove any manufacturing residue from the drum and tub Pour 1 2 a measure of detergent into the dispenser drawer and start the machine Load the laundry Open the door by pulling the door handle outwards Place the laundry in the drum one item at a time shaking them out as much as possible Close the door 2 Measure out the detergent Pull out the dispenser drawer until it stops Measure out the amount of detergent required and pour it into the main wash compartment LII If you have selected the PREWASH option or the SOAK programme pour detergent into the compartment marked LU JETSYSTEM wash As the Jetsystem is flexible and adjusts water intake according to wash load size it 1s not possible to give you exa
36. oollens and delicate fabrics with the hand washing care symbol Soak Select this programme for heavily soiled laundry Pour the detergent into the compartment LU This programme is not suitable for wool The machine performs a soak at 30 C and stops with the water in the drum The water can be emptied out by depressing the START PAUSE button Important If the water is not emptied out within 18 hours the machine empties automatically At the end of the soak after having emptied out the water you can select the washing programme Turn first the programme selector dial to O then select the programme and depress the START PAUSE button 10 Rinses With this programme it is possible to rinse and spin garments which have been washed by hand The machine performs 3 rinses followed by a final spin at 1200 r p m The spin speed can be reduced by depressing SPIN SPEED button Softeners Hand washed garments can be softened with this programme The machine performs 1 rinse followed by a final spin at the max speed which can be reduced by depressing SPIN SPEED button tJ Drain For emptying out the water of the last rinse in programmes with the RINSE HOLD option Turn first the programme selector dial to O then select programme J and depress the START PAUSE button Spin Separate spin at the maximum speed for hand washed garme
37. or covered with crumbly or soft material insert a rigid support base under the feet to prevent noise vibration or displacement The base should protrude a few centimetres beyond the edges of the machine A Warning The machine should NOT be placed on deep pile carpeting Note Please ensure that when the appliance is installed it is easily accessible for the engineer in the event of a breakdown In the interest of the environment Washer dryers and dishwashers should be connected to the FOUL drainage system the water will then be taken to a sewage works for treatment before being discharged safely into a river It is essential that these appliances are not connected to the surface water drainage system as this water is discharged directly into a river or stream and may cause pollution If you require any further advice please contact your local water authority SHOWER SINK TOILET WASHING MACHINE DISHWASHER lee SURFACE WATER DRAINS amp SEWERS FOUL SEWERS SEWAGE UNTREATED TREATMENT DISCHARGE WORKS y TREATED DISCHARGE RIVER Electrical connection Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person WARNING THIS APPLIANCE MUST BE EARTHED The manufacturer declines any liability should this safety measure not be observed Before switching on make sur
38. p to soak the stain before washing with a special pre soak product or biological detergent If you have used the machine to wash rinse or spin only non colour fast garments there may be dye left in the sump To ensure any subsequent wash is not contaminated with the dye select and carry out a rinse and spin programme without any garments to ensure that any dye is removed from the sump Do not leave the damp laundry load in a heap too long before drying Avoid drying dark clothes with light coloured fluffy items such as towels as these can attract the fluff If you overdry the laundry besides wasting energy any subsequent ironing may become more difficult because the fabric could be heavily crumpled Remove the laundry when the appliance has finished drying To avoid a static charge when drying is completed use either a fabric softener when you are washing the laundry or a fabric conditioner specifically for tumble dryers Particularly delicate items such as synthetic curtains woollen and silk garments with metal inserts nylon stockings bulky garments such as anoraks bedcovers quilts sleeping bags and duvets must not be machine dried Garments padded with foam rubber or materials similar to foam rubber must not be machine dried they represent a fire hazard Also fabrics containing residues of setting lotions or hair sprays nail solvents or similar solutions must not be machine dried in order to avoid the forma
39. ramme Warning For NON STOP programmes it is also essential not to exceed the maximum load sizes of 2 25 kg for cotton and 1 5 kg for synthetics 1 Load the laundry 2 Add detergent and fabric softener Do not use dosing device ball when carrying out the NON STOP programme because the plastic material is not designed to withstand the high drying temperature 3 Switch the machine on by depressing the ON OFF button 4 Select the wash programme 5 Select eventually the required options by means of the relevant buttons If possible do not select a spin speed lower than that proposed by the appliance to avoid a too long drying time so saving energy In any case the reduction of the spin speed is only possible after selecting drying The lowest values you can select are the following 900 r p m for cottons and 700 r p m for synthetics 6 Select the drying time 7 Start the programme by depressing the START PAUSE button 8 At the end of the programme turn the selector dial to Reset O and press the ON OFF button again to switch the machine off 9 Remove the laundry i Washing and Drying Hints Do NOT overload the machine Weigh the laundry the first few times you use the appliance The average weights of the most common items are listed below as a guide 1000g 1 kg Sheet 700 1000 g Pillow case 100 200 g Tablecloth 400 500 g Serviette 50 100 g Tea towel 70 120 g Linen h
40. reet Stornoway Isle of Lewis PA87 2QW 2 6 amp 8 Woodmarket Kelso Borders TD5 7AX 7 King Street Kirkwall Orkney KW15 1JF Scottish Hydro Electric Central Warehouse Inveralmond Perth PH13AF NORTH EAST GATESHEAD GRIMSBY HULL Unit 356a Dukesway Court Dukesway Gateshead NE11 0BH 15 Hainton Avenue Grimsby N E Lincs DN32 9AS Unit 1 Boulevard Industrial Estate Hull HU3 4AY DUMFRIES DUNOON EDINBURGH GLASGOW 93 Irish Street Dumfries DG12PQ 7 Hill Street Dunoon Argyll PA23 7AL Unit 12 Dumbryden Ind Estate 2 Dumbryden Road Edinburgh EH14 2AB Unit 4 Wellington Road Bishopriggs Glasgow G64 2SA SHETLAND OWN SALES SHETLAND OWN SALES WHALSAY OWN SALES 3 4 Carlton Place Lerwick Shetland ZE1 OPW Bolts Shetland 26 North Road Lerwick Shetland ZE1 OPE Leask Electrical Harisdale Symbister Whalsay Shetland ZE2 9AA NORTHERN IRELAND BELFAST Owenmore House Kilwee Business Park Dunmurry Belfast BT17 0HD NVERNESS SLE OF ARRAN SLE OF BARRA SLES OF BUTE Unit 3BI Smithton Ind Estate Smithton Inverness IV2 7WL R Haggerty Bruach Blackwaterfoot Isle of Arran J Zerfah 244 Bruernish Isle of Barra Western Islands HS9 5QY Walker Engineering Glenmhor Upper Serpentine Road Rothesay Isle of Bute PA20 9EH CARDIFF OSWESTRY WALES Unit 4 Guardian Industrial Estate Clydesmuir Roa
41. rogramme before it starts When the programme has started you can only reset it by turning the programme selector dial to O and then you can select the new programme Start it by depressing the START PAUSE button Interrupting a programme Depress the START PAUSE button to interrupt a programme which is running the corresponding light starts to flash Depress the same button to restart the programme Cancelling a programme Turn the selector dial to O to cancel a programme which is running Now you can select a new programme Opening the door after the programme has started You can open the door after having set the washer dryer to PAUSE provided the following conditions exist the drum temperature is over 40 C the level of the water is not high the drum is not turning If these requirements are met when you pause the machine the DOOR light goes out and the door can be opened Should it not be possible to open the door and should it be absolutely necessary to do so switch the machine off by pressing the ON OFF button After approximately 3 minutes you can open the door Pay attention to the level and temperature of the water in the machine When you close the door and press the ON OFF button again the machine will resume the programme from the point where it had been interrupted Programme information Wool Washing programme for machine washable wool as well as for hand washable w
42. s displayed The countdown is updated every hour Incorrect option selection If an option which is not compatible with the set wash programme is selected the message Err is displayed for 2 seconds Alarm codes In the event of operating problems some alarm codes can be displayed for example 20 see paragraph Something not working End of programme When the programme has finished a flashing zero is displayed The door can be opened en KI If you have selected the Rinse Hold option the zero will not flash 12 START PAUSE button This button has three functions Start Pause Draining of water Spin Start After having selected the required programme press this button to start the machine the corresponding pilot light stops flashing If you have selected the delayed start the machine begins its countdown The duration of the programme or the delay appears on the display Pause To interrupt a programme which is running depress the Start Pause button the corresponding pilot light starts to flash To restart the programme from the point at which it was interrupted press the START PAUSE button again Draining of water spin By depressing the Start Pause button The water of programme FJ Soak is emptied out The water of the last rinse on programmes with RINSE HOLD option is emptied out and the laundry is spun 13
43. se the laundry is not evenly distributed in the drum The laundry is redistributed by reverse rotation of the drum This may happen several times before the unbalance disappears and normal spinning can resume If after 10 minutes the laundry is still not evenly distributed in the drum the machine will not spin In this case redistribute the load manually and select the spin programme The machine makes an unusual The machine is fitted with a type of motor which makes an unusual noise noise compared with other traditional motors This new motor ensures a softer start and more even distribution of the laundry in the drum when spinning as well as increased stability of the machine No water is visible in the drum Machines based on modem technology operate very economically The machine does not dry or does not dry properly Service amp Spare Parts In the event of your appliance requiring service or if you wish to purchase spare parts please contact your local Zanussi Service Force Centre by telephoning 0870 5 929929 Your telephone call will be automatically routed to the Service Force Centre covering your post code area The addresses are listed on the following pages Before calling out an engineer please ensure you have read the details under the heading Something Not Working When you contact the Service Force Centre you will need to give the following details 1 Your name address and post code 2
44. shes Cotton Acrylic Mix Normal Maximum Cotton Linen or Viscose Colourfast at 40 C but not 60 C Acrylics Acetate Triacetate Wool ee gg a Restos Men mixes Polyester wool blends Much Reduced Minimum Wool wool mixtures Silks Hand wash only Do not machine wash BLEACHING A Chlorine bleach may be used IRONING c Hot iron Cotten Linen Viscose c Warm iron Polyester mixtures Wool cl Cool iron Acrylic Nylon Polyester DRY CLEANING B May be dry cleaned Other letters and or a bar beneath the circle will indicate the required process to the dry cleaner TUMBLE DRYING with high heat setting C with low heat setting e May be tumble dried X A cross through any symbol means DO NOT Important Notes For best results always use the dispenser drawer for dispensing detergents and liquid additives Once the dispenser has been filled close it by pushing it in gently This is particularly important if you are using fabric conditioner to avoid the conditioner entering the 16 machine prematurely When using liquid detergent and a prewash programme place the detergent into the correct compartment in the dispenser drawer after the prewash has finished Washing Programmes Section Cotton Cotton Cotton Cotton Cotton 30 40 Synthetics Synthetics Synthetics 30 40 Delicates 30 40 30
45. st be emptied out before opening the door A steadily lit zero appears on the display Release of the lock is indicated by the coming on of the END light and by the going out of the DOOR light A flashing zero appears on the display Turn the programme selector dial to Reset O Switch the machine off by pressing the ON OFF button Remove the laundry from the drum and carefully check that the drum is empty so as to avoid any forgotten items being damaged in a subsequent wash e g shrinking or their colour running into a load of whites If you do not intend to carry out another wash close the water tap Leave the door open to prevent the formation of mildew and unpleasant smells Drying only Warning Do not exceed the maximum laundry loads 2 25 kg for linen and cottons 1 5 kg for synthetics The water tap must be open and the drain hose must be positioned in the sink or connected to the drain pipe 1 Load the laundry 2 Depress the ON OFF button to switch the machine on 3 Select the drying programme lf for cotton or synthetics 4 Depress the Drying Time button until the time you want appears in the display The corresponding light comes on 5 Press the START PAUSE button to start the programme 6 At the end of the cycle turn the programme selector dial to Reset O and press the ON OFF button again to switch the appliance off 7 Remove the laundry 13 Automatic washing and drying NON STOP prog
46. t can be selected for cotton and synthetic items This option cannot be selected with the Economy programmes Normal For normally soiled laundry The machine is pre set for this function Quick For lightly soiled laundry By selecting this option the washing time is reduced by the following number of minutes 53 minutes for cotton at 95 C 63 minutes for cotton at 60 C 24 minutes for synthetics 8 minutes for delicates This option can be selected for cotton synthetic and delicates but not together with the Economy programmes 9 Drying Time button By depressing this button you can select the desired drying time according to the fabrics cotton or synthetics you have to dry To select the drying time you have to push the button until the drying time you want appears in the display For COTTON you can select a drying time from 10 to 130 minutes For SYNTHETICS you can select a time from 10 to 100 minutes For automatic Washing amp Drying programmes the drying time is displayed for 2 seconds then the duration of the programme will appear 10 Delay Start button The wash programme can be delayed from hour up to a maximum of 24 hours The button must be pressed after selecting the programme and before pressing the START PAUSE button The figures indicating the delay appear for about 3 seconds in the display The duration of the selected wash programme is then displayed One minute after depressing the START
47. the right polythene bag Repeat the operation for the left and central polythene bags Re fit the bottom panel using the 4 screws supplied with the door hinges in the plastic bag and the previously removed screw 28 Set the machine upright and remove the two remaining bolts from the back Pull out the three plastic spacers from the holes into which the bolts were fitted Plug the open holes with the plugs supplied with the instruction booklet Positioning Install the machine on a flat hard floor Make sure that air circulation around the machine is not impeded by carpets rugs etc Check that the machine does not touch the wall or other kitchen units Never place cardboard wood or similar materials under the machine to compensate for any unevenness in the floor Your new washer dryer has been designed to be permanently plumbed in to your home s water supply and drainage system However if this is not possible it may be connected to a suitable existing tap with the drain hose discharging into a sink The appliance has an inlet hose with female 3 4 BSP thread connector If this connection is not compatible with the plumbing of the existing installation a variety of connectors are available from good hardware stores and plumbers merchants to suit most domestic plumbing Any alteration to your existing plumbing must be carried out by a competent person or qualified plumber Water inlet Connect the
48. the specially designed dosing device which should be placed on top of the laundry and at the back of the machine drum Tf you use a dosing device in a washer dryer please ensure the dosing device ball is removed before carrying out a drying programme FABRIC CONDITIONERS These are ideal for improving softness and also reduce static cling on synthetics and make ironing easier They are available in two types For example Lenor liquid fabric softener for use in the washing machine washer dryer The liquid fabric softener should be poured into the compartment marked with the symbol amp Follow the manufacturer s dosage instructions and never exceed the MAX level Bounce conditioning sheets for use in a tumble dryer We recommend the conditioning sheets are pinned using a safety pin to an article of laundry and placed in the tumble dryer Wash Care Symbols Wash care labels inside garments recommend how to launder your clothes with the best results The care labelling code is in line with care labelling used in the rest of Europe The symbols used make it easy to select the correct programme on your washing machine WASHING SYMBOL WASH ACTION FABRIC Normal Maximum White Cotton or Linen without Special Finishes E g Normal Maximum Cotton Linen or Viscose without Special Finishes Colourfast at 60 C Reduced Medium Nylon Polyester Cotton Viscose with Special Fini
49. tion of harmful vapours For drying follow the indications given on the manufacturer s labels May be tumble dried Drying at high temperature O Drying at reduced temperature E Do not tumble dry Important As a dryer the machine works on the condensation principle Therefore the water taps must be open and the drain hose must drain water into a sink or into the drain pipe even during the drying cycle Which detergent To ensure you obtain the best wash results from your appliance it is important to use the right detergent in your everyday wash and only detergents recommended for use in automatic machines To maintain the appearance of your clothes and household textiles and to make them last longer you should use different types of detergent for different washes whether for whites colours or delicates WHITES We recommend the Ariel product range which is biological and designed to provide excellent cleaning and stain removal even at low temperatures NON BIOLOGICAL If you prefer to use a non biological detergent which does not contain enzymes we recommend Fairy Fairy provides good cleaning and stain removal COLOUREDS For coloured items you should use a detergent which is designed to clean while maintaining the original colour Ariel Color does not contain bleach and therefore helps to preserve colours DELICATE ITEMS When washing delicates such as woollens you should use a product
50. which is specially designed to care for fine fabrics Dreft Automatic is suitable for woollens and other delicates AUTOMATIC LAUNDRY BLEACH For additional stain removal you may wish to use a product such as Ace Gentle Bleach which is used in addition to your chosen detergent Ace is suitable for all washable fabrics including silks woollens and coloureds 15 And in which form Not only are there different types of detergent but they are also available in different forms Whether you chose a powder or liquid in traditional or compact form is your own personal choice TRADITIONAL POWDERS Pour the powder directly into the dispenser drawer Do not sprinkle powder onto clothes in the machine drum TRADITIONAL LIQUIDS Liquid can be placed in the main wash compartment of the detergent drawer marked with the symbol LIU start the machine immediately upon placing the detergent in the dispenser drawer Alternatively the detergent is measured into the specially designed dosing device which should be placed on top of the laundry and at the back of the machine drum COMPACT POWDERS AND LIQUIDS Compact detergents or concentrates as they are also known are available in liquid or powder form and generally require a smaller dosage Follow the manufacturer s instructions to ensure the most economical usage Pour the detergent directly into the dispenser drawer or alternatively measure the detergent into
Download Pdf Manuals
Related Search