Zanussi ZHC 590 Instruction Manual
Contents
1. l s For concrete ceilings use the appropriate plugs for the screw size not provided For Cavity ceiling with inner space with wall thi ckness of approx 20 mm Screws not provided For wooden beam ceilings use 4 wood screws not provided e For wooden shelf use 4 screws with washers and nuts not provided D Fixing the Frame Unfasten the two screws fastening the upper chimney stack 2 1 to the frame and remove the chimney from the upper stack If you wish to adjust the height of the frame proceed as follows e Unfasten the four safety screws located at the top in the frame separation area A Unfasten the eight metric screws joining the two columns located at the sides of the frame B e Adjust the frame to the height required then replace all the screws removed as above To guarantee greater stability in the frame replace the four safety screws in the last hole available A e Insert the upper chimney stack from above and leave Y it running free on the frame 14 INSTALLING THE COOKER HOOD e Lift the frame up making sure that the index over the frame plate is turned backwards Fit the frame slots onto the two screws inserted in the ceiling as above and turn until reaching the centre of the adjustment slot Tighten the two screws and fasten the other two screws provided before locking the screws comple tely i2. Ref Q ty Installation Components 12f 4 Screws M6 x 15 21 1 Drilling template Qty Documentation 1 Instruction Manual 12 INSTALLING THE COOKER HOOD Clearance Height The cooker hood is designed to be fitted over a cook ing appliance at the clearance heights stated providing the maximum output of the appliance beneath does not exceed the maximums quoted in the Technical Speci fications If the output of the appliance below the cooker hood exceeds the maximum outputs quoted please refer to the cooker manufacturer s installation instructions A Built in Electric Hob 650mm clearance B Built in Gas hob 700mm clearance A clearance height of 650mm 25 1 2 is required when C Slot in Electric Cooker 685mm clearance installed above a built in electric hob or 700mm 27 1 2 D Slot in Gas Cooker 787mm clearance when installed above a built in gas hob A clearance height of 685mm 27 is required when installed above a slot in electric cooker or 787mm 30 1 2 when installed above a slot in gas cooker When installed between adjoining wall cabinets the wall cabinets must not overhang the hob and the distance between the underside of the cabinet and the worktop must be 450mm If the height of the wall cabinet is less than 450mm a gap of 50mm must be maintained either side of the hob This cooker hood must not be installed above a cooking appliance with a high level grill The hood
3. 0 1 4090751 Email service eid electrolux ie Customer Care Department For general enquiries concerning your Zanussi appliance or for further information on Zanussi products please contact our Customer Care Department by letter or telephone at the address below or visit our website at www zanussi co uk Customer Services Department Major Appliances Zanussi Addington Way Luton Bedfordshire LU4 9QQ Tel 08705 727 727 calls to this number may be recorded for training purposes 18 CE Dir 89 336 CEE 73 23 CEE 93 68 CEE Electrolux ple 2002 436002645_04 060303
4. N Before carrying out any maintenance or clean ing isolate the cooker hood from the mains supply The cooker hood must be kept clean as a build up of grease or fat can be a fire hazard External Cleaning Wipe the cooker hood frequently with warm soapy water using a mild detergent Never use scouring pads or abrasive cleaners Never use excessive amounts of water when cleaning particularly around the control panel Metal Grease Filters The filters are washable and must be cleaned when the Led S1 lights up or at least every 2 months of opera tion or more frequently for particularly heavy usage IS Remove the metal grease filters one at a time by Open the lighting unit by pulling on the notch e Releasing the catches on the filters the filters can be removed The metal grease filters should be washed by hand in mild soapy water or in a dishwasher Allow to dry completely before replacing lt gt Alarm signal reset Switch off the lights and extractor motor Press Button T3 for at least 3 seconds until the leds start to flash MAINTENANCE AND CLEANING Before carrying out any maintenance or cleaning isolate the cooker hood from the mains supply Charcoal Filters In the recirculation mode the charcoal filters absorb smells and unwanted odours ES Enabling the alarm signal e In Recirculation version Hoods the Filter saturation alarm can be enabled on installation or at a later date e Turn the L
5. Replacement filters and halogen light can be obtained from your local Service Force Centre SOMETHING NOT WORKING If having followed these instructions carefully your cooker hood fails to work properly please carry out the following checks The cooker hood will not start The cooker hood is not working effectively The cooker hood has switched off during opera tion If after all these checks the fault persists contact your local Service Force Centre quoting the model and serial number Please note that it will be necessary to provide proof of purchase for any in guarantee service calls Check the hood is connected to the electricity supply Make sure the switch is in the ON position The fan speed is set high enough for the task The grease filter is clean The kitchen is adequately vented to allow the entry of fresh air If set up for recirculation check that the charcoal filter is still effective If set up for extraction check that the ducting and outlets are not blocked The safety cut out device has been tripped Tum off the hob and then wait for the device to reset In guarantee customers should ensure that the above checks have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown SERVICE AND SPARE PARTS If you require an engineer or spare parts contact your local Service Force Centre by telephoning 08705 929929 Your telephone call wi
6. to use the instruction book The following Symbols will be found in the text to guide you through the instruction book A Safety instructions IS Step by step instructions IMPORTANT SAFETY INFORMATION These warnings are provided in the interests of your safety Ensure that you understand them all before installing or using this appliance Your safety is of paramount importance If you are unsure about any of the meanings of these warnings contact the Customer Services Department E Installation Any installation work must be undertaken by a quali fied electrician or a competent person This hood must be installed in accordance with the installation instructions and all measurements must be adhered to e If the cooker hood is installed for use above a gas appliance then the provision for ventilation must be in accordance with the Gas Safety Codes of Practice BS 6172 BS 5440 and BS 6891 Natural Gas and BS 5482 LP Gas 1994 the Gas Safety Installation amp Use Regulations the Building Regulations issued by the Department of the Environment the Building standards Scotland Consolidated Regulations issued by the Scottish Development Department The fan motor of this cooker hood incorporates a cut out device which will operate if the cooker hood is installed below the minimum height recommended under section Clearance Height or if the motor be comes overheated If the cut out device is activated switch off
7. AAA ZANUSSI Thank you for buying a Zanussi product To enable you to use your appliance effectively and safely please read this instruction book carefully before using the appliance and retain for future reference If you require guidance in the use of the appliance or require further information on Zanussi Products please contact our Customer Services Department For general enquiries concer ning your Zanussi appliance or for further information visit our website at http www zanussi co uk Customer Services Department Major Appliances Zanussi Addington Way Luton Bedfordshire LU4 9QQ Calls to this number may be recorded for training purposes 08705 727 727 To register ownership please ensure you complete and return the guarantee card supplied with the appliance For the User Important Safety Information Your Appliance Operating Instructions Cooker Hood Controls To Operate Recirculation Extraction Maintenance and Cleaning External Cleaning Metal Grease Filters Charcoal Filters To Remove Replace Charcoal Filter Changing the Halogen Light Something Not Working Service and Spare Parts Guarantee Conditions For the Installer Technical Information Electrical Connections Electrical Requirements Electrical Connection Installing the Cooker Hood Installation Requirements Unpacking Fitting the Wall Brackets Fitting the Canopy Hood Venting Recirculation Fitting the Chimney Stack Guide
8. ailed information about recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product ELECTRICAL CONNECTIONS A THIS APPLIANCE MUST BE EARTHED Electrical Requirements Any permanent electrical installation must comply with the latest I E E Regulations and local Electricity Board regulations For your own safety this should be under taken by a qualified electrician e g your local Electricity Board or a contractor who is on the roll of the National Inspection Council for Electrical Installation Contracting NICEIC Electrical Connection Before connecting to the mains supply ensure that the mains voltage corresponds to the voltage on the rating plate inside the cooker hood This appliance is fitted with a 3 core mains cable and must be permanently connected to the electricity supply via a double pole switch having 3mm minimum contact gap on each pole A Switched Fuse Connection Unit to BS1363 Part 4 fitted with a 3 Amp fuse is a recom mended mains supply connection accessory to ensure compliance with the Safety Requirements applicable to fixed wiring instructions This appliance conforms to BS 800 1988 and EEC Directive No 78 308 regarding suppression of radio and television interference INSTALLING THE COOKER HOOD Please ensure that when the appliance is installed it is easily accessible to an engineer in the event of a breakdown A A
9. can be installed above these heights but for optimum performance it should be installed at the distances quoted for the appropriate heat source This appliance can be used in either extraction mode ducting or recycling mode filtering The hood is supplied suitable for recirculation with the charcoal filters fitted When used in the extraction mode ducting the char coal filters are not required and must be removed and destroyed 13 INSTALLING THE COOKER HOOD IS Drilling the Ceiling Support Shelf e Use a plumb line to mark the centre of the hob on the ceiling support shelf Place the drilling template 21 provided on the ceiling support shelf making sure that the template is in the correct position by lining up the axes of the template with those of the hob e Mark the centres of the holes in the template e Drill the holes at the points marked e For concrete ceilings drill for plugs appropriate to the screw size e For hollow brick ceilings with wall thickness of 20 mm drill 4 10 mm immediately insert the Dowels not provided For wooden beam ceilings drill according to the wood screws used For wooden shelf drill 7 mm For the power supply cable feed drill 10 mm e For the air outlet Ducted Version drill according to the diameter of the external air exhaust duct connection Insert two screws of the following type crossing them 440 6 D and leaving 4 5 mm from the ceiling i AN
10. e Centre listed below to give them details of your new home They will then ensure that the local Service Organisation is aware of your move and able to look after you and your appliances France Senlis 33 0 3 44 62 22 22 Germany Nurnberg 49 0 911 323 2600 Italy Pordenone 39 0 1678 47053 Sweden Stockholm 46 0 20 78 77 50 UK Luton 44 0 8705 727 727 10 INSTALLATION INSTRUCTIONS A It is dangerous to alter the specifications or attempt to modify this product in any way Technical Information DIMENSIONS HEIGHT OF CANOPY 935 mm HEIGHT OF CHIMNEY UPPER SECTION 290 mm LOWER SECTION 935 mm WIDTH OF CANOPY 370 mm DEPTH OF CANOPY 370 mm ELECTRICAL SUPPLY VOLTAGE 220 240 V 50Hz POWER CONSUMPTION 410 W FAN MOTOR 330 W LAMPS 4x20 W 80 W CE Note CE Marking certifies that this appliance complies with the requirements laid down in EEC directive 89 336 Electromagnetic compatibility and subsequent modifications and Low Voltage directive 72 23 E The symbol X on the product or on its packaging indicates that this product may not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product For more det
11. e cooker hood is ducted to the outside the charcoal filter must be removed 15 INSTALLING THE COOKER HOOD IS Ducting Connection Connect the ducting chosen to the 150mm ducting spigot on top of the motor housing or the 150 120mm ducting spigot item 9 and secure using the jubilee clips item 25 e A 120 125mm collar item 9a is provided to fit over the 120mm ducting spigot when 125mm ducting is fitted A If the room where the cooker hood is to be used contains a fuel burning appliance such as a central heating boiler then its flue must be of the room sealed or balanced flue type If other types of flue or appliances are fitted sure that there is an adequate supply of air to the room The cooker ducting extraction mode must never be connected to central heating flues radiators or water heaters etc Recirculation The cooker hood is supplied specified for use in the recirculation mode with the charcoal filter fitted In the recirculation mode contaminated air is passed through the charcoal filter to be purified and recirculated into the kitchen through the grille outlets on either side of the chimney IS Recirculation Connection e Insert reducer flange 9 on the extractor outlet e Push fit connector 15 onto the reducer flange e Insert extension piece 14 2 sideways into connector 15 making sure that the outlet corresponds with the mouth of the chimney 16 INSTALLING THE COOKER HOOD Chimney Stac
12. hould you attempt to repair the appliance yourself Repairs carried out by inexperienced persons may cause injury or more serious malfunction Refer to your local Zanussi Ser vice Force Centre Always insist on genuine spare parts YOUR APPLIANCE 144 En 935 935 545 4 5 370 OPERATING INSTRUCTIONS The cooker hood is designed to extract unpleasant odours from the kitchen it will not extract steam The appliance can be installed to recirculate or extract contaminated air Control Panel The hood can be switched on pushing directly onto the requested speed without firstly having to select 0 1 but ton KEY LED FUNCTIONS L 0 1 Light Turns lighting on and off T1 0 1 Motor on First speed When pressed for about 1 seconds the motor 4 switched off E ae T2 Speed on Second speed T3 Speed on Third speed O T4 Speed Fixed Max speed Flashing Intensive speed ET a Suitable for the strongest cooking vapours and odours The function becomes active when the button is pushed for about 2 T an seconds After 10 minutes of functioning it turns off automatically This function can ar be interrupted by means of pressing any 1 of the buttons Ba S1 Led Fixed Indicates that the Metal grease filters saturation alarm has been triggered and mo F the filters need to be washed The alarm is triggered after 100 working hours Reset check the Maintenance parag
13. ights and the suction Motor off Disconnect the Hood using the Main switch or the double pole switch on the mains power supply e Restore the connection by pressing and holding T1 e Release the button All five LEDs are turned on e Within 3 seconds press T1 until LEDs T1 and T4 flash in confirmation LED flashes twice Activated charcoal filter saturation alarm ENABLED LED flashes once Activated charcoal filter saturation alarm DISABLED The filter is not washable and cannot be regenerated It must be replaced when led S1 flashes or at least every 4 months The alarm signal will only light up when the extractor motor is switched on gt To Remove Replace the Charcoal Filters Open the lighting unit by pulling on the notch Remove the metal grease filters Remove the saturated activated carbon filter by releasing the fixing hooks e Fit the new filter by hooking it into its seating e Replace the metal grease filters This appliance can be a possible fire hazard if the grease and charcoal filters are not cleaned and replaced as recommended ES Alarm signal reset e Switch off the lights and extractor motor e Press button T3 for at least 3 seconds until the leds start to flash ES Changing the halogen light e Remove the halogen lamp from the lamp holder by pulling gently e Replace the lamp with a new one of the same type making sure that you insert the two pins properly into the housings on the lamp holder
14. k The chimney consists of two sections The lower chimney measures with the Hood body and recirculation grilles 935 mm and the upper chimney measures 290 mm The overall installed measurement is min 935 max 1215 mm EF Fitting the Upper Chimney and the Hood Body e Position the upper chimney stack and fix the top of it to the frame using 2 of the screws removed as above Open the lighting unit by pulling on the notch discon nect it from the hood canopy by sliding out the fixing pin e Remove the activated charcoal filters if fitted In order to fix the hood body to the frame insert the 4 screws 12f in their seats It is necessary to leave at least 4 5 mm gap between the screw heads and the frame plate Hook the hood canopy to the frame and turn it to the left until it reaches the stop then lock the screws immediately to prevent the hood canopy from falling out accidentally e Make sure that the outlet of the extension piece 14 1 is horizontally and vertically aligned with the chimney outlet If this is not the case remove the lower Chimney Stack and adjust the position of connector 15 replace the elements as described above Insert Connector Extension 14 1 sideways into Ex tension 14 2 e Fit the directional grill 8 into the housing provided Also make sure that it is properly fitted into connector 14 1 DS Electrical Connection e Ensure that the supply cable connec
15. ll be routed to your local Service Force Centre For the address of your local Service For ce Centre and further information about Service Force please visit the website at www serviceforce co uk For general assistance with your appliance or for further information on Zanussi products please contact our Customer Services Department Customer Services Department Major Appliances Zanussi Addington Way Luton Bedfordshire LU4 900 Tel 08705 727 727 calls to this number may be recorded for training purposes GUARANTEE CONDITIONS We Zanussi undertake that if within twenty four months of the date of the purchase this Zanussi built in appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials the company will at our option repair or replace the same FREE OF ANY CHARGE for labour materials or carriage on condition that e The appliance has been correctly installed and used only on the electrical supply stated on the rating plate e The appliance has been used for normal domestic purposes only and in accordance with the manufacturer s operating and maintenance instructions e The appliance has not been serviced maintained repaired taken apart or tampered with by any person not authorised by us All service work under this guarantee must be undertaken by Zanussi Service Force Centre e Any appliance or defective part replaced shall become the property of this company Ho
16. ll installations must comply with the local authorities requirements for the discharge of exhaust air Incorrect installation may affect the safety of this cooker hood Installation Requirements Before installation check the wall to which the cooker hood is to be fitted for electric cables water pipes or gas This cooker hood is designed to be fixed to any orizontal surface over a cooking area and can be used in the extraction ducted to the outside or recirculation mode The installation work must be undertaken by a qualified and competent person The manufacturer disclaims any responsibility for damage due to incorrect installation of the cooker hood or if the hood is not installed in compliance with relevant regulations controlling this type of installation Unpacking L img Before unpacking the cooker hood position the carton i 14 2 d with the arrows pointing upwards as illustrated on the 21 a carton o gt The cooker hood is made up of the following com A ponents 15 Ref Q ty Product Components 1 1 Hood Body complete with Controls Light Blower Filters 2 1 Upper Chimney LA Telescopic frame complete with extractor consisting of 71a 1 Upper frame 74b 1 Lower frame 8 1 Air Outlet Grill 9 1 Reducer Flange 150 120 mm Ja 1 120 125mm collar 141 1 Air Outlet Connection Extension 142 1 Air Outlet Extension 15 1 Air Outlet Connection 25 2 Pipe clamps
17. me visits are made between 8 30am and 5 30pm Monday to Friday Visits may be available outside these hours in which case a premium will be charged EXCLUSIONS This Guarantee does not cover Damage or calls resulting from transportation improper use or neglect the replacement of any lilght bulbs or removable parts of glass or plastic e Costs incurred for calls to put right appliances improperly installed or calls to appliances outside the United Kingdom Appliances found to be in use within a commercial environment plus those which are the subject of rental agree ments e Products of Zanussi manufacture which are not marked by Zanussi This guarantee is in addition to your statutory and legal rights ZANUSSI EUROPEAN GUARANTEE If you should move to another country within Europe then your guarantee moves with you to your new home subject to the following qualifications e The guarantee starts from the date you first purchased your product e The guarantee is for the same period and to the same extent for labour and parts as exists in the new country of use for this brand or range of products e This guarantee relates to you and cannot be transferred to another user e Your new home is within the European Community EC or European Free Trade Area e The product is installed and used in accordance with our instructions and is only used domestically i e a normal household Before you move please contact your nearest Customer Car
18. raph Flashing indicates that the activated charcoal odour filter saturation alarm has been triggered and the filter has to be replaced the metal grease filters must also be washed The activated charcoal odour filter is triggered after 200 working hours Activation and Reset check the Maintenance paragraph OPERATING INSTRUCTIONS To Operate Select the required fan speed and light if required Recirculation In the recirculation mode the contaminated air enters the cooker hood through the grease filters The air is cleaned by passing through the charcoal filters before being passed back into the kitchen through the grilles in either side of the chimney stack Extraction In the extraction mode the contaminated air enters the cooker hood passing through the grease filters and is passed out through the ducting into the atmosphere To obtain the best performance when cooking it is advi sable to switch the cooker hood on for a few minutes before you start cooking and leave it running for about 15 minutes after finishing When used in the ducting mode the charcoal filters are not required Never do flamb cooking under this cooker hood Never leave frying pans unattended during use as over heated fats and oils can catch fire Do not leave naked flames under the cooker hood Ensure heating areas on your hob are covered with pots and pans when using the hob and cooker hood simultaneously MAINTENANCE AND CLEANING
19. t is possible to adjust the frame by turning it making sure that the screws do not come out of their housing in the adjustment slot The Frame must be securely fastened so as to support both the weight of the Hood and the stress caused by occasional axial pressure against the fitted Appliance After fixing make sure that the base is stable even when the Frame is subjected to lateral stress e If the Ceiling is not strong enough in the area where the hood is to be fixed the Installer must strengthen the area using suitable plates and counterplates anchored to resistant structures Extraction The cooker hood is more effective when used in the extraction mode ducted to the outside Venting kits may be purchased through your retailer or DIY store and must be ducted to an outside vent of 8125mm 5 or 8150mm 6 For the best performance use the shortest possible duct run and the minimum number of bends Where flexible ducting is fitted it should not be turned through very tight bends as this may impair the perform ance of the hood It is recommended a maximum length of 3 metres with one bend to be installed to be reduced metre for each 900 bend If a distance is greater than 3 metres the efficiency of the hood could be impaired The ducting used must be manufactured from fire retardent material conforming to the relevant British Standard or DIN 4102 B1 When th
20. the fan motor and allow the cooker hood to cool The cut out device will reset itself when the fan motor has cooled significantly e Itis dangerous to alter the specifications or modify this product in any way When installed between adjoining wall cabinets the wall cabinets must not overhang the hob e If the room where the hood is to be used contains a fuel burning appliance such as a central heating boiler then its flue must be of the room sealed or balanced flue type lf other types of flue or appliances are fitted ensure that there is an adequate supply of air to the room The ducting system for this appliance must not be connected to any existing ventilation system which is being used for any other purpose Do not install above a cooker with a high level grill m Child Safety This appliance is designed to be operated by adults Children should not be allowed to tamper with the controls or play with the appliance During Use This product is for domestic use only Never leave frying pans unattended during use as over heated fats and oils might catch fire Never do flamb cooking under this cooker hood Do not leave naked flames under the hood This cooker hood is designed to extract unpleasant odours from the kitchen it will not extract steam Maintenance and Service This appliance can be a hazard if the synthetic paper and charcoal filters are not replaced as recommen ded Under no circumstances s
21. tor is properly inserted into the Suction device socket e Hook up the Commands connector Cmd e Hook up the Spotlights connector Lux to the socket provided behind the lighting unit cover e For the recirculation version fit the activated carbon odour filter e Replace the grease filters e Replace the lighting unit 17 Service and Spare Parts In the event of your appliance requiring service or if you wish to purchase spare parts please contact your local Service Force Centre by telephoning 08705 929929 Your telephone call will be automatically routed to the Service Force centre covering your post code area For the address of your local Service Force Centre and further information about Service Force please visit the website at www serviceforce co uk Before calling out an engineer please ensure you read the details under the heading Something not working When you contact the Service Force Centre you will need to give the following details 1 Your name address and post code 2 Your telephone number 3 Clear and concise details of the fault 4 The model and serial number found on the rating plate 5 The purchase date Please note that a valid purchase receipt or guarantee documentation is required for in guarantee service calls For Customer Service in Ireland please contact us at the address below Zanussi Electrolux Group Irl Ltd Long Mile Road Dublin 12 Republic of Ireland Tel 353
Download Pdf Manuals
Related Search