Zanussi ZDT41 User's Manual
Contents
1. User manual 2 S E R Dishwasher Uj MANUAL ZANUSSI ZDT41 Get Living Contents Safety information Control panel Washing programmes Use of the appliance Setting the water softener Use of dishwasher salt Use of rinse aid Loading cutlery and dishes Use of detergent OoOoNDON ON amp W PS A Safety information i For your safety and correct operation of the appli ance read this manual carefully before installation and use Always keep these instructions with the appli ance even if you move or sell it Users must fully know the operation and safety features of the appliance Correct use e The appliance is designed exclusively for domestic use Only use the appliance to clean household utensils that are applicable for dishwashers Do not put solvents in the appliance Risk of explosion Put the knives and all items with sharp points in the cutlery basket with their points down If not put in a horizontal position in the upper basket Use only branded products for dishwashers detergent salt rinse aid Ifyou open the door while the appliance is in operation hot steam can escape Risk of skin burns e Do not remove dishes from the dishwasher before the end of the washing programme e When the washing programme is completed discon nect the mains plug from the mains socket and close the water tap Only an authorised service engineer can repair this appliance Use only original spare parts2. A Warning Always close the door after you load or unload the appliance An open door can be dangerous Arrange service dishes and large lids around the edge of the lower basket i Use the cutlery grid If the dimensions of the cutlery prevent use of the cutlery grid remove it Arrange the items to let water touch all surfaces For longer items fold the cup racks up i Prevent to put plates in the first three sections in the front part of the upper basket Make sure the plates tilt forward Adjustment of the height of the upper basket If you put large plates in the lower basket first move the upper basket to a upper position Use of detergent i Only use detergents powder liquid or tablet that are applicable for dishwashers Follow the data on the packaging e Dosage recommended by the manufacturer e Storage recommendations ws Do not use more than the correct quantity of deter gent to save an environment A Warning Adjust the height before you load the upper basket Maximum height of the dishes in upper basket lower basket Upper position 20 cm 31 cm Lower position 24 cm 27 cm V 62221 HA Do these steps to move the upper basket to the upper or lower position 1 Move the front runner stops A out 2 Pull the basket out 3 Put the basket in the upper or lower position 4 Replace the fron
3. e Do not do repairs yourself to prevent injury and dam age to the appliance Always contact your local Service Force Centre General safety e Persons including children with reduced physical sensory mental capabilities or lack of experience and 2 Setting and starting a washing programme _ _ _ _ 10 Care and cleaning 11 What to do if 12 Technical data 13 Environment concerns 13 Installation 14 Water connection 14 Electrical connection 15 Subject to change without notice knowledge must not use the appliance They must have supervision or instruction for the operation of the ap pliance by a person responsible for their safety Obey the safety instructions from the manufacturer o the dishwasher detergent to prevent burns to eyes mouth and throat e Do not drink the water from the dishwasher Detergen residues can stay in your appliance e Always close the door when you do not use the appli ance to prevent injury and not to stumble over the open door e Do not sit or stand on the open door Child safety e Only adults can use this appliance Children must get supervision to make sure that they do not play with the appliance e Keep all the packaging away from children There is a risk of suffocation e Keep all detergents in a safe area Do not let children touch the detergents e Keep children away from the appliance when the door is open Installation e Make sure
4. at level 5 time to increase the water softener level by one step 1 Switch on the appliance 8 Press the on off button to save the operation 2 Make sure that the appliance is in setting mode Use of dishwasher salt Set switch to position 1 or 2 A Caution Only use dishwashers salt Types of salt that are not applicable for dishwashers cause damage to the water softener Fill the salt container with 1 litre of water only the first operation Use of rinse aid A Caution Only use branded rinse aid for dishwashers Do these steps to fill the rinse aid dispenser i It is normal that water overflows from the salt con tainer when you fill it with salt ij Make sure that there is no grain of salt outer of the salt compartment Salt which stays on the tank for a while drills the tank It is recommended to start a wash ing programme immediately after you fill the salt con tainer This prevents of corrosion because of spilled salt Important Fill the salt container from time to time The salt cap has a refill indicator window in the center A green float is easy to see when there is a salt inside the container It almost goes out of view when the salt is gone max Fill when the rinse aid in dicator B becomes clear Loading cutlery and dishes Helpful hints and tips
5. connectors and extension cables There is a risk of fire Do not replace the mains cable yourself Contact the Service Force Centre A Warning The appliance is supplied with a 13 amp plug attached Use a 13 amp ASTA approved BS 1362 fuse if it is necessary to change the fuse in the plug supplied 15 To buy accessories consumables and spare parts at our online shop please visit www zanussi co uk www zanussi com 156985570 00 042009 CE
6. furred with limescale Clean the water tap er tap is closed Open the water tap e The filter in the water inlet hose is blocked Clean the filter e The connection of the water inlet hose is not correct The hose can be kinked or squashed Make sure that the connection is correct e continuous flash of the light of the run ning programme intermittent audible signal e 2 flashes of the end indicator light The dishwasher will not drain The programme does not start e There is a blockage in the sink spigot Clean the sink spigot e The connection of the water drain hose is not correct The hose can be kinked or squashed Make sure that the connection is correct e The appliance door is not closed Close the door e Mains plug is not connected in Put in the mains e The fuse has blown out in the household fuse box Replace the fuse After the check switch on the appliance The programme continues from the point of interruption Ifthe malfunction shows again contact your Service Force Centre These data are necessary to help you quickly and cor rectly Model Mod e Product number PNC 12 e Serial number S N For these data refer to the rating plate Write the necessary data here Model description Product number Serial number The cleaning results are not satisfactory The dishes are not clean Soil e The selected washing programme is not a
7. A Caution Only use the appliance for household utensils that are applicable for dishwashers Do not use the appliance to clean objects that can absorb water sponges household cloths etc e Before you load cutlery and dishes do these steps Remove all food remainings and debris Make burnt remaining food in pans soft e While you load cutlery and dishes do these steps Load hollow items e g cups glasses and pans with the opening down Make sure that water does not collect in the con ainer or in a deep base Make sure that cutlery and dishes do not lie inside one another Makesure that cutlery and dishes do not cover other utlery and dishes Make sure that glasses do not touch other glasses Put small objects in the cutlery basket Plastic items and pans with non stick coatings can keep water droplets Plastic items do not dry as well as porcelain and steel items Q Caution Do not fill the rinse aid dispenser with other products e g dishwasher cleaning agent liquid detergent This can cause damage to the appli ance Adjusting the dosage of rinse aid The rinse aid dial is set at the factory at position 3 To increase or decrease the dosage refer to What to do if e Put light items in the upper basket Make sure that the items do not move A Caution Make sure that the spray arms can move freely before you start a washing programme
8. amme Open the door e The programme stops Close the door e The programme continues from the point of interrup tion End of the washing programme Switch off the appliance in these conditions e The appliance stops automatically Care and cleaning A Warning Switch the appliance off before you clean the filters Cleaning the filters Important Do not use the appliance without the filters Make sure that the installation of the filters is correct Incorrect installation will cause unsatisfactory washing results and damage to the appliance fa T O C B SF Fully clean the filters A B and C below running wa ter e The audible signals for the end of the programme op erate 1 Open the door The end indicator light comes on The programme indicator light stays on 2 Press the on off button 3 For better drying results keep the door ajar for some minutes before you remove the dishes Let the dishes cool down before you remove them from the appliance Hot dishes are easily damaged Removing the load e First remove items from the lower basket then from the upper basket e There can be water on the sides and door of the appli ance Stainless steel becomes cool more quickly than the dishes Remove the flat filter A from the bottom of the ap pliance To remove filters B and C turn the handle approxi mately 1 4 anti
9. clockwise Put the flat filter A in the bottom of the appliance Install the flat filter cor rectly under the two guides D Put the filter system in po sition To lock the filter system turn the handle clockwise until it locks in position 11 Important Do not remove the spray arms If the holes in the spray arms become clogged remove remaining parts of soil with a cocktail stick External cleaning Clean the external surfaces of the appliance and control panel with a damp soft cloth Only use neutral detergents Do not use abrasive products scouring pads or solvents acetone trichloroethylene etc What to do if The appliance does not start or stops during operation Frost precautions A Caution Do not install the appliance where the temperature is below 0 C The manufacturer is not responsible for damage because of frost If not possible empty the appliance and close the door Disconnect the water inlet hose and remove water from the water inlet hose If there is a fault first try to find a solution to the problem yourself If you cannot find a solution to the problem yourself contact the Service Force Centre Fault code and malfunction Possible cause and solution e continuous flash of the light of the run ning programme e intermittent audible signal e 1 flash of the end indicator light The dishwasher does not fill with water e The wa e The water tap is blocked or
10. lection cancel but ton until programme indicator light A flashes and programme indicator light B comes on 4 Press the programme selection cancel button again Programme indicator light A comes on Programme indicator light B starts to flash 5 Wait until programme indicator light A goes off Programme indicator light B continues to flash The end indicator light comes on The audible signals are activated 6 Press the programme selection cancel button again The end indicator light goes off The audible signals are deactivated 7 Switch off the appliance to save the operation Do these steps to activate the audible signals 1 Do the above procedure until the end indicator light comes on Washing programmes Degree of soil Type of load Programme description Prewash Crockery cutlery DEE wash up lo 65 C GP Normal soil ae and ans 2 intermediate rinses p P Final rinse Drying Normal or light Crockery and cut Main wash up to 65 C N soil lery Final rinse Prewash Crockery and cut Main wash up to 50 C gfe 2 Normal soil ie 1 intermediate rinse y Final rinse Drying Degree of soil Type of load Programme description Partial load to be 1 cold rinse to avoid food scraps from stick iy Any completed later in the day This programme does not require the use of detergent 1 This is the perfect daily programme to clean a not fully load Ideal for a family of 4 pers
11. liary functions e Level of the water softener e Activation deactivation of the audible signals e Analarm if the appliance has a malfunction e To deactivate activate the audible signals Refer to the section Audible signals e To cancel a washing programme in progress Refer to the chapter Setting and starting a washing pro gramme Setting mode The appliance is in setting mode when all the programme indicator lights are off and the end indicator light flashes The appliance must be in setting mode for these opera tions To set a washing programme To set the water softener level To deactivate activate the audible signals If a programme indicator light is on cancel the pro gramme to go back to the setting mode Refer to the chapter Setting and starting a washing programme Programme indicator lights A and B Apart the selection of the corresponding washing pro gramme these lights have an auxiliary functions e The adjustment of the water softener level e Deactivation activation of the audible signals Audible signals You can hear an audible signal e At the end of the washing programme e When the appliance has a malfunction Washing programmes The activation of the audible signals is set at the factory Do these steps to deactivate the audible signals 1 Switch on the appliance 2 Make sure that the appliance is in setting mode 3 Press and hold the programme se
12. n the drying results are not satisfactory 1 Fill the rinse aid dispenser with rinse aid 2 Set the rinse aid dosage to position 2 Do these steps to use the detergent powder again 1 Fill the salt container and the rinse aid dispenser 2 Set the water softener to the highest level 3 Do a washing programme without dishes 4 Adjust the water softener Refer to the chapter Setting the water softener 5 Adjust the rinse aid dosage i Different brands of detergent dissolve in different times Some detergent tablets do not have the best cleaning results during short washing programmes Use long washing programmes when you use detergent tab lets to fully remove the detergent When the washing programme operates you cannot change the programme Cancel the washing pro gramme A Warning Only interrupt or cancel a washing programme if necessary A Caution Open the door carefully Hot steam can come free Cancelling a washing programme 1 Press and hold the programme selection cancel but ton for approximately 3 seconds The programme indicator light goes off The end indicator light starts to flash 2 Release the programme selection cancel button to cancel the washing programme At this time you can do these steps 1 Switch off the appliance 2 Set anew washing programme Fill the detergent dispenser with detergent before you set a new washing programme Interrupting a washing progr
13. nce is correct the door does not catch on the sides of the cabinet If the door does not close correctly loosen or tighten the adjustable feet until the appliance is level Caution Do not connect the appliance to new pipes or pipes that are not used for a long time Let the water run for some minutes then connect the inlet hose Drain hose 7 max 85 cm max s00 cm E a a 9 3 Connect the water drain hose to the sink spigot The internal diameter must not be smaller than the diam eter of the hose A If you connect the water drain hose to a trap spigot under a the sink remove the plastic membrane A If you do not J I remove the membrane remaining food can cause a block gt S we age in the drain hose spigot A Caution Make sure that the water couplings are ight to prevent water leakage Electrical connection A Warning The manufacturer is not responsible if Make sure that the mains plug is accessible after you do not follow these safety precautions installation Ground the appliance according to safety precautions Do not pull the mains cable to disconnect the appliance Make sure that the rated voltage and type of power on the Always pull the mains plug rating plate agree with the voltage and the power of the local power supply Always use a correctly installed shockproof socket Do not use multi way plugs
14. necessary contact your local water authority French degrees TH Water hardness Water hardness setting dH TH mmol l Clarke manually electronically 51 70 91 125 9 1 12 5 64 88 2 10 43 50 76 90 7 6 9 0 53 63 2 9 37 42 65 75 6 5 7 5 46 52 2 8 29 36 51 64 5 1 6 4 36 45 2 7 23 28 40 50 4 0 5 0 28 35 2 6 19 22 33 39 3 3 3 9 23 27 2 5 15 18 26 32 2 6 3 2 18 22 1 4 11 14 19 25 1 9 2 5 13 17 1 3 4 10 7 18 0 7 1 8 5 12 1 2 lt 4 lt i lt 0 7 lt 5 1 1 1 No use of salt required i You must set the water softener manually and elec 3 Press and hold the programme selection cancel but tronically ton 4 Release the programme selection cancel button Manual adjustment when programme indicator light A starts to flash and The appliance is set at the factory at position 2 programme indicator light B comes on 5 Wait until programme indicator light B goes off Programme indicator light A starts to flash The end indicator light starts to flash 6 Press the programme selection cancel button one time Programme indicator light A starts to flash The setting function of the water softener is acti vated The end indicator light flashes to show the level of the water softener Example 5 flashes pause 5 flashes pause etc canes level 5 Electronic adjustment i 7 Press the programme selection cancel button one The water softener is set at the factory
15. ons who only want to load breakfast and dinner crockery and cutlery 2 Test programme for test institutes Please refer to separate leaflet supplied for test data Consumption values in minutes in kWh in litres AEP 105 115 1 5 1 7 23 25 30 0 9 9 je 130 140 1 0 1 2 14 16 Ay 12 0 1 5 i The pressure and temperature of the water the var iations of power supply and the quantity of dishes can change these values Use of the appliance Refer to the following instructions for each step of pro 5 Set the correct washing programme for the type of cedure load and soil 1 Make a check if the water softener level is correct for 6 Fill the detergent dispenser with the correct quantity the water hardness in your area If necessary set the of detergent water softener 7 Start the washing programme 2 Fill the salt container with dishwasher salt i nin i If you use detergent tablets refer to the chapter Use 3 Fill the rinse aid dispenser with rinse aid of detergent 4 Load cutlery and dishes into the dishwasher Setting the water softener The water softener removes minerals and salts from the mmol l millimol per litre international unit for the water supply Minerals and salts can have bad effect on hardness of water the operation of the appliance e Clarke Water hardness is measured in equivalent scales Adjust the water softener to the water hardness in your e German degrees dH area If
16. orrectly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product For more detailed information about recycling of this product please contact your local council your household waste disposal service or the shop where you purchased the product The packaging materials are environmentally friendly and can be recycled The plastic components are identified by markings e g gt PE lt gt PS lt etc Discard the packaging materials in the applicable container at the community waste disposal facilities 13 AN Warning To discard the appliance follow the procedure e Pull the mains plug out of the socket e Cut off the mains cable and mains plug and discard them Installation Warning Make sure that mains plug is disconnected from the mains socket during installation Important Obey the instructions in the enclosed template to e Build in the appliance e Install the furniture panel e Connect to the water supply and drain Install the appliance under a counter kitchen worktop or sink If a repair is necessary the appliance must be easily ac cessible for the engineer Put the appliance adjacent to a water tap and a drain For the venting of the dishwasher only water fill water drain and power supply cable openings are necessary Water connection Water inlet hose Connected the appliance
17. pplicable for the type of load and e The baskets are loaded incorrectly so that water cannot reach all surfaces e Spray arms do not turn freely because of incorrect arrangement of the load e The filters are dirty or not correctly installed e The quantity of detergent is too little or missing Limescales particles on the dishes e The salt container is empty e The water softener is adjusted on a wrong level e The salt container cap is not closed correctly The dishes are wet and dull e No rinse aid has been used e The rinse aid dispenser is empty There are streaks milky spots or Decrease the rinse aid dosage a bluish coating on glasses and dishes Dry water drop signs on glasses Increase rinse aid dosage and dishes Technical data Width cm Height cm Dimensions Depth cm Electrical connection Voltage Overall power Fuse Water supply pressure Minimum Maximum Capacity Place settings Environment concerns e The detergent can be the cause 59 6 81 8 87 8 55 9 Information on the electrical connection is given on the rating plate on the inner edge of the dishwasher door 0 5 bar 0 05 MPa 8 bar 0 8 MPa 12 The symbol R onthe product or on its packaging indicates that this product may not be treated as household waste Instead it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of c
18. t runner stops A in their initial po sition A Caution If the basket is in the upper position do not put cups on the cup racks f at Q Fill the detergent dispens lf you use a washing pro er A with detergent gramme with prewash phase put more detergent in the prewash detergent compartment B Use of detergent tablets Put the detergent tablet in the detergent dispenser A Detergent tablets contain e detergent e rinse aid Setting and starting a washing programme i Set the washing programme with the door ajar The washing programme only starts after you close the door Until then it is possible to modify the settings Do these steps to set and start a washing programme 1 Switch on the appliance 2 Make sure that the appliance is in setting mode 3 Press the programme selection cancel button again and again to set the washing programme Refer to the chapter Washing programmes The programme indicator light comes on 4 Close the door The washing programme starts automatically e other cleaning agents Do these steps to use detergent tablets 1 Make sure that the detergent tablets are applicable for your water hardness Refer to the instructions from the manufacturer 2 Set the lowest levels of water hardness and rinse aid dosage i It is not necessary to fill the salt container and the rinse aid dispenser Do these steps whe
19. that the appliance is not damaged because of transport Do not connect a damaged appliance If necessary contact the supplier e Remove all packaging before first use e A qualified and competent person must do the electri cal installation e A qualified and competent person must do the plumb ing installation Do not change the specifications or modify this prod uct Risk of injury and damage to the appliance Do not use the appliance ifthe mains cable or water hoses are damaged ifthe control panel worktop or plinth area are dam aged that you can get access to the inner side of the appliance Control panel Contact your local Service Force Centre e Do not drill into the sides of the appliance to prevent damage to hydraulic and electrical components Warning Carefully obey the instructions for electrical and water connections I A B la ere ie50 0y Cancel On off button Programme selection cancel button Indicator light Programme indicator lights e fan a Indicator light Programme selection cancel button Use the programme selection cancel button for these op erations e To set the washing programme Refer to the chapter Setting and starting a washing programme e To set the water softener Refer to the chapter Setting the water softener The indicator light comes on when the washing pro gramme is completed Auxi
20. to a hot max 60 or cold water supply If the hot water comes from alternative sources of energy that are more environmentally friendly e g solar or pho tovoltaic panels and aeolian use a hot water supply to decrease energy consumption Connect the inlet hose to a water tap with an external thread of 3 4 Caution Do not use connection hoses from an old appliance f The water pressure must be in the limits refer to the chapter Technical data Make sure that the local water authority gives you the average mains pressure in your area Make sure that there are no kinks in the water inlet hose and that the water inlet hose is not squashed or entangled Turn the inlet hose to the left or the right to suit the in stallation Fit the locknut correctly to prevent water leaks 14 e Discard the door catch This prevents the children to close themselves inside the appliance and endanger their lives The dishwasher has adjustable feet to allow the adjust ment of the height Make sure that the water inlet hose the drain hose and the supply cable are not kinked or squashed when you nsert the machine Attaching the appliance to the adjacent units Make sure that the counter below which you attach the appliance is a safe structure adjacent kitchen units cab inets wall Adjusting the level of the appliance Make sure that the appliance is level to close and seal the door correctly If the level of the applia
Download Pdf Manuals
Related Search