Zanussi ZDT 311 User's Manual
Contents
1. Open the lid Set the dosage level The Close the lid and press un dose is factory setin po til it locks sition 4 Loading cutlery and dishes Sponges household cloths and any objectthat When loading the dishes and cutlery please can absorb water may not be washed in the niote dishwasher Dishes and cutlery must not impede the rotation of the spray arms Load hollow items such as cups glasses pans etc with the opening downwards so Before loading the dishes you should Remove all left over food and debris Soften remnants of burnt food in pans 13 that water cannot collect in the container e Plastic items and pans with non stick coat or a deep base ings have a tendency to retain water drops Dishes and items of cutlery must not lie these items will not dry as well as porcelain inside one another or cover each other and steel items To avoid damage to glasses they must Light items plastic bowls etc must be loa not touch ded in the upper basket and arranged so Lay small objects in the cutlery basket they do not move For washing in the dishwasher the following cutlery and dishes are not suitable are of limited suitability e Cutlery with wooden horn china or mother of e Only wash stoneware in the dishwasher if it is pearls handles Specially marked as being dishwasher safe by the e Plastic items that are not heat resistant manufacturer Older cutlery with glued p2. be no smaller than the diameter of the hose provided Electrical connection Z CAUTION Safety standards require the appliance to be earthed Prior to using the appliance for the first time ensure that the rated voltage and type of supply on the rating plate match that of the supply where the appliance is to be installed The fuse rating is also to be found on the rating plate notkinked crushed oren drain hose to an under tangled sink trap spigot the entire plastic membrane A must be removed F ail ure to remove allthe mem brane will result in food particles building up over time eventually blocking the dishwasherdrain hose Spigot Always plug the mains plug into a correctly in Stalled shockproof socket Multi way plugs connectors and extension cables must not be used This could constitute a fire hazard through over heating If necessary have the domestic wiring system socket replaced In case that the electrical ca ble has to be replaced contact your local Serv ice Force centre The plug mustbe accessible after the appliance has been installed Never unplug the appliance by pulling on the cable Always pull the plug The manufacturer accepts no liability for failure to observe the above safety precautions 27 Fitting under a counter IMPORTANT Carefully follow the instructions on the enclosed template for building in the dishwasher and fit ting the furniture panel Z WARNING Th
3. is below 0 C If this is unavoidable empty the machine close the ap pliance door disconnect the water inlet pipe and empty it Moving the machine Ifyou have to move the machine moving house etc Environmental concerns Packaging material The packaging materials are environmentally friendly and can be recycled The plastic com ponents are identified by markings e g gt PE lt gt PS lt etc Please dispose of the packaging materials in the appropriate container at the community waste disposal facilities AN CAUTION When a unitis no longer being used Pull the plug out of the socket Cut off the cable and plug and dispose of them Dispose of the door catch This prevents children from trapping themselves inside and endangering their lives ZANUSSI 1 Unplug it 2 Turn the water tap off 3 Remove the water inlet and discharge ho ses 4 Pull the machine out together with the ho ses Avoid over tilting the machine during transpor tation The symbol X on the product or on its pack aging indicates that this product may not be treated as household waste Instead it should be taken to the appropriate collection point for the recycling of electrical and electronic equip ment By ensuring this product is disposed of correctly you will help prevent potential nega tive consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this pr
4. mode Simultaneously press and hold function buttons B and C until the lights of function buttons A B and C start flashing 3 Press function button C the lights of func tion buttons A and B turn off while the light of function button C goes on flashing At the same time the end of programme in dicator light illuminates indicating that the audible signals are active 4 To deactivate teh audible signals press 5 again function button C the end of pro gramme indicator light turns off indicating that the audible signals have been deacti vated To memorise the operation switch off the dishwasher by pressing the On Off button To activate again the audible signals simply follow the above operations until the end of programme indicator light illuminates Select and start a washing programme IMPORTANT Select the washing programme and delay start with the door slightly opened The start of the programme or the countdown of the delay start will occur only after the closure ofthe door Until then itis possible to modify the set made k 3 Check that the baskets have been loaded correctly and that the spray arms are free to rotate Check that the water tap is opened Press the On Off button The dishwasher must be in setting mode 4 Press the button corresponding to the re quired programme see Washing pro grammes chart When a programme has been selected the corresponding light will illuminate 5
5. Close the dishwasher door the pro gramme starts automatically Setting and starting the programme with delay start 1 After having selected the washing pro gramme press the delay start button until the light corresponding to the chosen hours flashes 3h 6h 9h 2 Close the dishwasher door the countdown starts automatically 3 The countdown will decrease with steps of 3 hours 4 The opening of the door will interrupt the countdown Close the door the countdown will continue from the point at which it was interrupted 5 Once the delay start has elapsed the pro gramme will start automatically Cancelling the delay start To cancel a delay startin progress you have to reset the dishwasher Press simultaneously and keep pressed func tion buttonsB and C until all programme button light are illuminated Cancelling a delay start involves also the can celling of the washing programme set In this case you have to set the washing programme again N CAUTION Interrupt or cancel a washing programme in progress ONLY if it s absolutely necessary ZANUSSI Attention Hot steam may escape when the door is opened Open the door carefully Interrupt a washing programme in pro gress Open the dishwasher door the programme will stop Close the door the programme will Start from the point at which it was interrup ted Cancel a washing programme in progress Open the dishwasher door press simultaneously a
6. ZANUSSI a J a N User manual NG 4 Dishwasher x Ne L 4 ZDT 311 Thank you for selecting our appliance We wish you lots of enjoyment with your new appliance and we hope that you will consider our brand again when purchasing household appliances Please read this user manual carefully and Keep it throughout the product life cycle as a reference document The user manual should be passed on to any future owner of the appliance Contents Safety information 3 Useofdetergent st 16 Control panel ee 4 Mult Tab function __________ 17 Audible signals e 5 Unloading the dishwasher ________ 19 Select and start a washing Care and cleaning ______2_2_2____ 19 progamme o ceai nanan 6 Environmental conces _________ 21 Washing programmes 8 Something not working _________ 21 eee ee 3 Consumption values 23 Setthewatersoftener 9 Technical data 24 Filling with dishwasher salt 11 Hints for test institutes 24 Filling with rinse aid 12 Installation 25 Adjusting the dosage of rinse aid 13 Loading cutlery and dishes 13 Safety information In the interest of your safety and to ensure the correct use before installing and first using the appliance read this user manual carefully in cluding its hints and warnings To avoid unnecessary mistakes and accidents it is im portant to ensure that all people using the applia
7. all power Fuse Information on the electrical connection is given on the rating plate on the inner edge of the dishwasher s door Water supply pressure Minimum Maximum MPa Capacity place settings Max weight kg Noise level dB A Hints for test institutes 0 05 0 8 12 37 47 Testing in accordance with EN 60704 mustbe carried out with appliance fully loaded and us ing the test programme see Consumption values 24 Test in accordance with EN 50242 must be carried out when the salt container and rinse aid dispenser have been filled with salt and E ZANUSSI rinse aid respectively and using the test pro gramme see Consumption values Full load 12 standard place settings Amount of detergent required 5g 25 g Type B Rinse aid setting position 4 Type Ill Lower basket cup racks position A Installation ZAN WARNING Water connection Any electrical and or plumbing work required to install this appliance should be carried out by a A WARNING qualified electrician and or plumber or compe The dishwasher mustnotbe connected to open tent person water appliances or instantaneous water heat ers This dishwasher may be fed with either hot max 60 or cold water Nevertheless we ad vise you a cold water supply 25 ZAN WARNING Only use for connection to the water mains new hose set old hos
8. an filters A B and C Turn the handle about 1 4 Remove filter A from the thoroughly under running turn anticlockwise and re base of the washing com water move filters B and C Put the flat filter A back in Replace the filters and the base of the washing lock by turning the handle compartment and ensure clockwise to the stop that it fits perfectly under the two guidesD Cleaning the spray arms NEVER try to remove the spray arms If residues of soil have clogged the holes in the Spray arms remove them with a cocktail stick External cleaning Clean the external surfaces of the machine and control panel with a damp soft cloth If necessary use only neutral detergents Never use abrasive products scouring pads or sol vent acetone trichloroethylene etc 20 partment Internal cleaning Ensure that the seals around the door the de tergent and rinse aid dispensers are cleaned regularly with a damp cloth We recommend every 3 months to run the wash programme for heavy soiled dishes using de tergent but without dishes Prolonged periods of non Operation If you are not using the machine for any pro longed period of time you are advised to 1 Unplug the appliance and then turn off the water 2 Leave the door ajar to prevent the forma tion of any unpleasant smells 3 Leave the inside of the machine clean Frost precautions Avoid placing the machine in a location where the temperature
9. are 1 intermediate rinse Final rinse Dry Auto washing programme During the Auto washing programme the amount of soil on the dishes is determined by how cloudy the water is If the appliance is partially loaded and the dishes lightly soiled the prewash main wash and rinse phases of the programme are shorter and the water consumption level is lower If the appliance is fully loaded and the dishes heavily soiled the prewash main wash and rinse phases of the programme are longer and the water consumption level is higher For this reason the programme duration water and energy consumption levels can vary within the stated range for Auto programme see Washing programmes chart During the Auto programme the temperature of the main wash water is also automatically ZANUSSI adjusted between 45 C and 70 C depending on the amount of soil on the dishes Firstuse Pour 1 litre of water inside the salt container and then fill with dishwasher salt Fill the rinse aid dispenser Before using your dishwasher for the first time e Ensure that the electrical and water connec tions comply with the installation instructions e Remove all packaging from inside the appli If you want to use combi detergent tablets such ance as 3 in 1 4 in 1 5 in 1 etc set the Multi Set the water softener Tab function see Multi Tab function Set the water softener The dishwasher is equippe
10. arts thatare nottempera Glazed patterns may fade if machine washed ture resistant frequently Silver and aluminium parts have a tendency to dis colour during washing Residues e g egg white e egg yolk and mustard often cause discolouring and i F staining on silver Therefore always clean left overs Steel items prone to rusting from silver immediately if itis not to be washed Wooden platters straight after use Items made from synthetics fibres Bonded cutlery items or dishes Long blades knives stored in an upright position are a potential hazard Long and or sharp items of cutlery such as carving knives must be placed horizontally in the removable knife basket which is positioned at the rear of the upper basket 14 ZANUSSI Load cutlery For best re sults we recommend you to use the cutlery grid pro vided if the size and di mensions of the cutlery allow it The two rows of prongs on the lower basket can be easily lowered to allow you to load pots pans and bowls Place knives and other items of cutlery with sharp points or edges with their handles facing upwards Risk of injury Load the lower basket Ar range serving dishes and large lids around the edge of the basket S PHPU I J UTIR IN Bil Load upper basket Light items plas
11. asher by pressing the On Off button 6 To deactivate the rinse aid dispenser again follow the above instructions until the end of programme indicator light turns off IMPORTANT If you decide to turn back to the use of standard detergent system we advise that you L 2 3 Deactivate the Multi Tab function Fill up the salt container and the rinse aid dispenser again Adjust the water hardness setting to the highestsetting and perform 1 normal wash ing programme without loading any dishes Unloading the dishwasher Hot dishes are sensitive to knocks The dishes should therefore be allowed to cool down before removing from the appli ance Empty the lower basket first and then the upper one this will avoid water dripping from the upper basket onto the dishes in the lower one Care and cleaning Cleaning the filters IMPORTANT NEVER use the dishwasher without filters In correct repositioning and fitting of the filters will produce poor washing results ZANUSSI 4 Adjust the water hardness setting accord ing to the hardness of the water in your area 5 Adjust the rinse aid dosage e Water may appear on the sides and the door of the dishwasher as the stainless steel will eventually become cooler than the dishes Z N CAUTION When the washing programme has finished it is recommended that the dishwasher is un plugged and the water tap turned off 19 Cle
12. cal and water connection carefully follow the instructions given in specific para product in any way graphs e Never use the dishwasher if the electrical supply cable and water hoses are damaged Control panel 2 lee gm cute wsiheetur vow Oth Leu a Z A Ao 3h es e 70 45 70 65 A30 e 050 e45 e e 6h Q Multi tab B e 9h gt L Cance L Multi tab On Off button Programme selection buttons Delay start button Indicator lights Function buttons Functions buttons In addition to the dishwashing programme se lection the following functions can also be set with the help of these buttons the setting of the water softener deactivation activation of the audible sig nals cancela washing programme ora delay start in progress activation deactivation of the rinse aid dispenser when the Multi tab function is ac tive IMPORTANT Setting mode Always remember that when ZANUSSI activating deactivating the rinse aid dispenser the appliance MUST be in setting mode Press On Off button All programme lightare illuminated the appliance is in setting mode Press On Off button ONLY a programme button is illuminated last performed or se lected programme still set In this case to return to setting mode the programme has to be cancelled To cancel a set programme
13. connection The dishwasher will not drain 3 intermittent audible signals Close the water tap and contact your local Service continuous flashing of the light of the running Force Centre programme 3 flashes of the end of programme indicator light Anti flood device is activated The programme does not start The dishwasher door has not been properly closed Close the door e The main plug is not plugged in Insert the mains plug e The fuse has blown in the household fuse box Replace the fuse Once these checks have been carried out continue from the point at which it was inter Switch on the dishwasher The programme will rupted 22 If the malfunction or fault code reappears con tact the Service Force Centre ZANUSSI For other fault codes notdescribed in the above chart please contact your Service Force Cen tre The wash results are not satisfactory The dishes are not clean The dishes are wet and dull There are streaks milky spots or a bluish coating on glasses and dishes Water drops have dries onto glasses and dishes If after all these checks the problem persists contact your local Service Force Centre Contact your local Service Force Centre quot ing the model Mod product number PNC and serial number S N This information can The wrong washing programme has been selected The dishes are arranged in such a way as to stop water reaching all parts of the surface The baskets must not be
14. d If the current level is 10 by pressing button A once level 1 is selected 5 To memorise the operation switch off the dishwasher by pressing the On Off button Unscrew the cap Only before filling with Using t e funnel provided salt for the first time fill pour in the salt until the the saltcontainer with wa container is filled with salt ter 11 IMPORTANT Immediately start a complete programme IMPORTANT Water will overflow from the containeras saltis added Sy di Remove any trace of salt Replace the cap tightly turning it clockwise until it stops with a click IMPORTANT Top up the special salt when the light on the control panel illuminates Filling with rinse aid i Open the lid Fill up with rinse aid The Clean up any rinse aid maximum level forfilling is which overflows Close indicated by max the lid and press until it locks SS 12 E ZANUSSI CAUTION Never fill the rinse aid dispenser with any other substances e g dishwasher cleaning agent liquid detergent This would damage the appliance Top up the rinse aid indica tor B becomes clear Adjusting the dosage of rinse aid Increase the dose if there are drops of water or Reduce the dose if there are whitish streaks on lime spots on the dishes after washing the dishes ora bluish film on glassware or knife blades
15. d with a water grees dH French degrees TH and mmol softener designed to remove minerals and salts millimol per litre international unit for the from the water supply which would have a det hardness of water rimental or adverse effect on the operation of The softener should be adjusted according to the appliance the hardness of the water in your area Y our The higher the content of these minerals and local Water Authority can advise you on the Salts the harder your water is Water hardness hardness of the water in your area is measured in equivalent scales German de Water hardness Adjusting the water hardness Use of salt setting TH mmol l ELTELNI electronically 51 70 91 125 9 1 12 5 2 level 10 yes 43 50 76 90 7 6 8 9 2 level 9 yes 37 42 65 75 6 5 7 5 2 level 8 yes 29 36 51 64 5 1 6 4 2 level 7 yes 23 28 40 50 4 0 5 0 2 level 6 yes 19 22 33 39 3 3 3 9 2 level 5 yes 15 18 26 32 2 6 3 2 1 level 4 yes 11 14 19 25 1 9 2 5 1 level 3 yes Water hardness Adjusting the water hardness Use of salt setting mmol l manually electronically 4 10 7 18 0 7 1 8 1 level 2 yes lt 4 lt 7 lt 0 7 1 level 1 no The water softener must be set in both ways manually using the water hardness dial and electronically Setting the water softener manually see table The water softener is factory set at position 2 Set switch to position 1 or 2 Setting the water softener electronical
16. e please use long washing Detergent tablets from different manufacturers programmes when using detergent tablets to dissolve at different rates For this reason ensure the complete removal of detergent some detergent tablets do not attain their full residuals Multi Tab function A HO 3h es eG70 45 70 65 A30 e 950 e45 ee e h Muti tab A B C 9h e gt L Cancel L Multi tab 17 This appliance is equipped with the Multi Tab function that allows the use of the Multi Tab combi detergent tablets These products are detergents with a combined cleaning rinsing and salt functions They can also contain other different agents depending on which kind of tablets you choose 3 in 1 4 in 1 5 in 1 etc Check whether these detergents are suitable for your water hardness See the manufactur ers instructions Once this function is selected it will remain ac tive also forthe following washing programmes With the selection of this function the inflow of rinse aid and salt from each respective supply container is automatically deactivated and also the indicator lights for salt and rinse aid are de activated Select the Multi Tab function before the start of a washing programme With the use of the Multi Tab function the cy cle durations may change Once the programme is running the Multi Tab function can NO longer be changed If you want to exclude the Multi Tab function y
17. e dishwasher mustbe secured againsttilting Therefore make sure that the counter it is fixed under is suitably secured to a fixed structure adjacent kitchen units cabinets wall This dishwasher is designed to be fitted under a kitchen counter or work surface No further openings for the venting of the dishwasher are required but only to let the wa ter fill and drain hose and power supply cable pass through 28 The dishwasher incorporates adjustable feet to allow the adjustment of the height During all operations that involve accessibility to internal components the dishwasher has to be unplugged Be sure that once the appliance has been in Stalled itis easily accessible for the service engineer in the event that a repair is required Levelling Good levelling is essential for correct closure and sealing of the door When the appliance is correctly levelled the door will not catch on either side of the cabinet If the door does not close correctly loosen or tighten the adjustable feet until the machine is perfectly level See enclosed template ZANUSSI 30 ZANUSSI LU eee ZANUSSI www electrolux com 156992690 00 05102007 Subject to change without notice CE
18. e setmustnotbe reused Z N CAUTION If the machine is connected to new pipes or pipes which have notbeen used fora long time you should run the water for a few minutes be fore connecting the inlet hose Water inlet hose with safety valve Connect the inlet hose to a water tap with an external thread of 3 4 After connecting the double walled water inlet hose the safety valve is next to the tap If the water inlet hose leaks the safety valve cuts off the water supply 26 Z N WARNING The electrical cable for the safety valve is in the double walled water inlet hose and is live Therefore do not immerse the water inlet hose or the safety valve in water Take care when installing the water inlet hose Place the water inlet hose in such a way that itis always lower than the bottom edge of the Safety valve If the water inlet hose or the safety valve is damaged remove the mains plug immediately Z N CAUTION A water inlet hose with safety valve MUST only be replaced by your local Service Force Centre Drain hose ZANUSSI T S Connect drain hose to the Required height 30 t0100 Ensure gt hoses are When connecting the sink cm above bottom of the dishwasher If you use a drain hose extension the total length should not be longer than 4 metres Likewise the internal diameter of the couplings used for connections to the waste outlet must
19. ly see table The dishwasher is factory set at level 5 A gO 3h es e 70 45 70 65 A30 50 e U45 ef e h Muti tab A B C 9h e gt L Cancel L Multi tab 1 Press the On Off button The dishwasher 2 Simultaneously press and hold function must be in setting mode buttons B and C until the lights of the func tion buttons A B and C start flashing 10 3 Press function button A the lights function buttons B and C turn off while the light of function button A goes flashing at the same time the end of programme indica tor light starts to flash along with a se quence of intermittent audible signals The current level is indicated by the number of flashes of the end of programme indicator light with a sequence ofintermittentaudible signals and a pause of a few seconds Examples 5 flashes 5 intermittent audible signals pause 5 flashes 5 intermittent audible signals pause etc level 5 6 flashes 6 intermittent audible signals pause Filling with dishwasher salt Z N CAUTION Use only special salt suitable for dishwashers ZANUSSI 6 flashes 6 intermittent audible signals pause etc level 6 4 To change the level press the function but ton A Each time button is pressed the level changes For the selection of a new level see the chart Examples If the currentlevelis 5 by pressing function button A once level 6 is selecte
20. nce are thoroughly familiar with its opera tion and safety features Save these instruc tions and make sure that they remain with the appliance if itis moved orsold so thateveryone using itthrough its life will be properly informed on appliance use and safety Correct use This dishwasheris only intended for washing household utensils suitable for machine washing Do not put any solvents in the dishwasher This could cause an explosion Knives and other items with sharp points must be loaded in the cutlery basket with their points down or placed in a horizontal position in the upper basket Only use products detergent salt and rinse aid suitable for dishwashers Avoid opening the door whilst the appliance is in operation hot steam may escape Do not take any dishes outof the dishwasher before the end of the dishwashing cycle After use isolate the appliance from the power supply and turn off the water supply This product should be serviced only by an authorised service engineer and only genu ine Spare parts should be used Under no circumstances should you attempt to repair the machine yourself Repairs car ZANUSSI ried outby inexperienced persons will cause injury or serious malfunctioning Contact your local Service Force Centre Always in sist on genuine spare parts General safety Dishwasher detergents can cause chemical burns to eyes mouth and throat Could en danger life Comply with the safety inst
21. nd keep pressed function buttonsB and C until all programme button is illuminated The washing programme has been cancelled Ifa new washing programme is to be selec ted check that there is detergent in the detergent dispenser Cancelling the delay start To cancel a delay startin progress open the door and press the delay start button the corresponding light turns off close the door the set washing programme will start automatically End of the washing programme The dishwasher will automatically stop and an audible signal informs you of the end of the washing programme Open the dishwasher door The end of programme indicator light is il luminated The indicator light of the programme just ended will remain on Switch off the dishwasher by pressing the On Off button IMPORTANT When the washing programme has finished it is recommended that the dishwasher is un Washing programmes plugged and the water tap turned off Intensive 70 Heavy soil Prewash CS Crockery cutlery pots and pans Main wash 2 intermediate rinses Final rinse Dry AUTO A 45 70 Normal Light soil Prewash Crockery and cutlery Main wash 1 or 2 intermediate rinses Final rinse Dry 65 A30 Light soil Main wash Crockery and cutlery Final rinse Bio 50 Normal soil Prewash ojo Crockery cutlery Main wash 1 intermediate rinse Final rinse Dry Glass 45 Normal soil Main wash Delicate crockery and glassw
22. oduct For more detailed information about recycling of this product please contact your local council your household waste disposal service or the shop where you purchased the product 21 Something not working The dishwasher will not start or stops during solved with the help of the indications described operation in the chart without calling out an engineer Certain problems are due to the lack of simple Switch off the dishwasher and carry out the fol maintenance or oversights which can be lowing suggested corrective actions Fault code and malfunction Possible cause and solution 1 intermittent audible signal e The water tap is blocked or furred with limescale continuous flashing of the light of the running Clean the water tap programme The water tap is tumed off Lflashofthe end ofprogramme indicatorlight Tum the water tap on The dishwasher does not fill with water The filter where present in the threaded hose fitting at the water inlet valve is blocked Clean the filter in the threaded hose fitting The water inlet hose has not been correctly laid or itis bent or squashed Check the water inlet hose connection 2 intermittent audible signals The sink spigotis blocked continuous flashing of the light of the running Clean out the sink spigot programme e The water drain hose has not been correctly laid or 2 flashes of the end of programme indicator itis bent or squashed light Check the water drain hose
23. or a programme in progress simultaneously press function but tonsB and C until ALL programme button lights are illuminated The programme has been can celled and the machine is now in setting mode setting the water softener deactivation activation of the audible sig nals Indicator lights Salt Illuminates when the special salt has run out 5 Is never illuminated while a washing programme is running Indicates the activation deactivation of the M ulti tab function see Multi tab function Multi tab function End of programme Illuminates when the washing programme has ended gt Italso has added functions of visual signalling as the setting of the water softener activation deactivation of the rinse aid dispenser deactivation activation of the audible signals intervention of an alarm due to the malfunction of the machine Audible signals A O e 70 45 70 65 A30 50 e45 ee 6h A B C 3h es amp Multi tab 9h e L Cancel L Multi tab Audible signals have been introduced to help indicate which operations the dishwasher is performing setting the water softener end of the programme e intervention of an alarm due to malfunction IMPORTANT Factory setting audible signals activated Deactivation activation of the audible sig nals 1 2 Press On Off button The dishwasher must be in setting
24. ou have to cancel the programme setting and then deactivate the Multi Tab function In this case you have to seta washing programme and desired options again Activation deactivation of the Multi Tab function Press simultaneously the two buttons posi tioned over the Multi Tab symbol until the Multi Tab function indicator light illuminates This means that the function is active To deactivate the function press the same but tons again until the indicator light correspond ing to the Multi Tab function symbol turns off 18 IMPORTANT If the drying results are notsatisfactory we sug gest that you 1 Fillup the rinse aid dispenser with rinse aid 2 Activate the rinse aid dispenser 3 Setthe rinse aid dosage to position 2 e The activation deactivation of the rinse aid dispenser can only be possible with the Multi Tab function active Activation deactivation of the rinse aid dispenser 1 Press the On Off button The dishwasher must be in setting mode 2 Press simultaneously buttons B and C un til the indicator lights of buttons A B and C start flashing 3 Press button B the indicator lights of but tons A and C turn off while the indicator light of button B goes on flashing 4 To activate the rinse aid dispenser press button B again the end of programme in dicator light illuminates indicating that the rinse aid dispenser has been activated 5 To memorise the operation switch off the dishw
25. overloaded The spray arms do notrotate freely due to incorrect arrangement of the load The filters in the base of the washing compartment are dirty or incorrectly positioned Too little or no detergent has been used Where there are limescales deposits on the dishes the salt container is empty or the incorrect level of the water softener has been set The drain hose connection is not correct The salt container cap is not properly closed Rinse aid was not used The rinse aid dispenser is empty Decrease rinse aid dosing Increase rinse aid dosing The detergent may be the cause Contact the de tergent manufacturer s consumer care line be found on the rating plate located on the side of the dishwasher door So that you always have these numbers at hand we recommend you to make a note of them here 23 Consumption values The consumption values are intended as a guide and depends on the pressure and the temperature of the water and also by the var iations of the power supply and the amount of dishes Consumption values Programme Programme duration in Energy consumption in Water litres minutes Intensive 70 80 90 1 6 1 8 22 24 AUTO 45 70 90 125 1 1 1 6 12 23 65 A30 30 0 9 9 BIO 50 Test pro 160 1 05 14 gramme for Test Insti tutes Glass 45 60 70 0 8 0 9 14 15 Technical data Dimensions Width x Height x Depth cm 59 6 x 81 8 87 8 x 55 5 Electrical connection Voltage Over
26. ruc tions of the dishwasher detergent manufacturer The water in your dishwasher is notfor drink ing Detergent residues may still be present in your machine Ensure that the door of the dishwasher is always closed when itis not being loaded or unloaded In this way you will avoid anybody tripping over the open door and hurting themselves Do not sit or stand on the open door Child safety This appliance is designed to be operated by adults Don t allow children to use the dishwasher unsupervised Keep all packaging well away from children There is risk of suffocation Keep all detergents in a safe place out of children s reach Keep children well away from the dishwasher when the door is open Installation Check your dishwasher for any transport damage Never connecta damaged ma chine If your dishwasher is damaged con tact your supplier All packaging must be removed before use Any electrical and plumbing work required to install this appliance must be carried out by a qualified and competent person For safety reasons it is dangerous to alter the specifications or attempt to modify this or if the control panel work top or plinth area are damaged such that the inside of the ap pliance is freely accessible Contact your local Service Force centre in order to avoid hazard All sides of the dishwasher must never be drilled to prevent damage to hydraulic and electric components Z N WARNING For electri
27. tic bowls etc must be loaded in the up per basket and arranged so they do not move For taller items the cup racks can be folded up wards If plates are to be loaded in the upper basket load them starting from the rear positions tilting them Slightly forwards and avoiding the front positions near the door 15 Adjusting the height of the upper basket If washing very large plates you can load them in the lower basket after moving the upper bas ket to the higher position Maximum height of the dishes in upper basket lower basket With upper basket raised 20 cm 31 cm With upper basket lowered 24 cm 27 cm IMPORTANT When the basket is in the higher position you will not be able to use the cup racks Move the front runner Refit the basket in the stops A ofthe upper bas higher position and re ket outwards and slide the place the stops A in their basket out original position Use of detergent IMPORTANT Observe the manufacturer s dosing and stor Only use detergents suitable for dishwashers age recommendations 16 E ZANUSSI Fill in the detergent in compartment A For programmes with pre When using detergent Close the lid wash add an additional tablets place detergent detergent dose in com tablets in compartment A partmentB Detergent tablets cleaning power during short washing pro grammes Therefor
Download Pdf Manuals
Related Search