Zanussi ZC135R Instruction Booklet
Contents
1. with a high water content may start to freeze if it has been placed in the coldest places in the fridge The picture shows the coldest and warmest places inside the fridge warm cold Meat fish and milk should be put in the coldest part of the cabinet The temperature will be affecteed by e How often the door is opened e How much food is stored e Position of the appliance See chapter Installation Zanussi 818 14 54 01 1 Measuring the temperature If the temperature is measured using a standard single thermometer this should be put in a glass of water centrally placed inside the cabinet This will reflect the temperature inside the food products Do not place the thermometer hanging or lying directly on the shelf an e Distribute foodstuffs to allow cold air to circulate freely between the products e Do not place food products directly against the cooling plate on the rear wall since they may freeze in this case e Also never put warm products into the cabinet Wait until they have cooled down e Cover all foods properly to avoid odours and flavours from tainting other food Switching off Set the thermostat control to the 0 position Unplug the power supply plug from the wall socket or alternatively remove the fuse Cabinet interior The shelves and door compartments are removable and can easily be re arranged Certain shelves must be lifted up by the rear edge to enable them to b2. When the appliance is not inuse 9 Something Not Working semek O Service and Spare Parts sea 10 Customer Care Department 10 Guarantee Conditions re Standard Guarantee Conditions 10 Guide to use the instruction book European Guarantee une rn 11 Instructions for the installer Technical specification 11 Installation oo oo 11 Unpacking a er ren 11 Removing the transport supports 12 Installing the cabinet 223 03 00 44ce enc 202 12 Electrical connection o ocoo o 13 Door Reversal van re 14 The following Symbols will be found in the text to guide you through the instructions Safety instructions 123 Step by step instructions for an operation Hints and tips Zanussi 818 14 54 01 1 Mode ZC135R Wire shelf Bottle shelf Vegetable drawer Egg tray Dairy compartment butter box Ventilation grille Door shelf Ne EAN Control Panel O A B A Green indicator light B Thermostat control Lights when the fridge is operating Use to switch on and set the desired temperature in the fridge xx o 7 oe YE Operation This appliance is designed to operate in ambient This appliance is designed for do temperatures surronding air temperature between mestic use only specifically for the 10 C and 32 C storage of edible foodstuffs If these temperatures are exceeded i e col
3. 8 z 7 ar ye cl eg EEE eh ur Rt an A Ds ae A Fat Wa aTa 5 aio y 1 A inaina se PP EA Late AA A ve Aia el an fa a x E n ais rape PR PIP TON PION De i FERIO RO NALS N RE a ey Ya s EA Ta aas EA REFRIGERATOR ZC135R INSTRUCTION BOOKLET 8181454 01 1 These warnings are provi RR Sh ER BER ded in the interests of your safety Ensure that you understand them all x WE 4 Es Se before installing or using the appliance Your safety is of paramount importance If you are insure about any of the meanings or warnings contact the Customer Care Department Keep the instruction booklet It will come in handy if you later sell the cabinet or give it to somebody else Prior to Installation Check the appliance for transport damage Under no circumstances should a damaged appliance be installed In the event of damage please contact your retailer Installation This appliance is heavy Care should be taken when moving it It is dangerous to alter the specifications or attempt to modify this product in any way Ensure that the appliance does not stand on the electrical supply cable If the supply cable is damaged it must be replaced by a cable avaliable from your local Service Force Center Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person Parts which heat up should not be exposed Whenever possible th
4. ctrician or competent person This appliance must be earthed The manufacturer declines any liability should these safety measures not be observed Electrical Requirements Before switching on make sure the electricity supply voltage is the same as that indicated on the appliance rating plate The appliance is supplied with a 13amp plug fitted In the event of having to change the fuse in the plug supplied a 13amp ASTA approved BS1362 fuse GREEN amp YELLOW 13 AMP FUSE must be used Should the plug need to be replaced for any reason The wires in the mains lead are coloured in accoordance with the following code Green and yellow Earth Blue Neutral Brown Live CORD CLAMP The wire coloured green and yellow must be connected to the terminal marked with the letter E or by the earth symbol or coloured grecen and yellow The wire coloured blue must be connected to the terminal marked N or coloured black The wire coloured brown must be connected to the terminal marked L or coloured red Upon completion there must be no cut or stray strands of wire present and the cord clamp must be secure over the outer sheath 13 Zanussi 818 14 54 01 1 Door Reversal 1 Close the cabinet and pull out the plug from the electrical outlet 2 Remove the ventilation grille There is a part on the grille that can be removed Remove it and transfer to the opposite side 3 Support the cabinet on a wooden b
5. der or warmer the appliance will not operate correctly 4 Zanussi 818 14 54 01 1 Before use eRemove all securing tapes eWash the inside of the appliance with lukewarm water with a little bicarbonate of soda added Sml to 0 5 litre of water Do not use soap or detergent as the smell maylinger Dry the appliance thoroughly Do not use detergents abrasive powders highly perfumed cleaning products wax polishes or products containing alcohol eCheck that the drain hose at the rear of the cabinet discharges into the drip tray eBefore inserting the power plug into the outlet and switching on the cabinet for the first time leave it standing upright for about 30 minutes or for 4 hours if it was transported horizontally Otherwise the com pressor may sustain damage This time will allow the oil sufficient time to return to the compressor To start the fridge and thermostat control Turn the thermostat control to the desired position 1 The lowest position of the thermostat control results in the highest temperature inside the cabinet 6 The highest position of the thermostat control results in the lowest temperature inside the cabinet 0 Off Allow the cabinet to run for a period of 24 hours whenever the temperature setting is changed This will allow the temperature to stabilise inside the cabinet A suitable temperature inside the fridge is approx 5 C If the thermostat control is set too cold food
6. e back of the appliance should be close to a wall but leaving the required distance for ventilation as stated in the installation instructions The appliance should be left for 2 hours after installation before it is turned on in order to allow the refrigerant to settle Child Safety Do not allow children to tamper with the controls or play with the product There is a risk of suffocation Keep packaging material away from children During Use This appliance is designed for domestic use only specifically for the storage of edible foodstuffs only It is not intended for commercial or industrial use Containers with flammable gases or liquids can leak at low temperatures Do not store any containers with flammable materials such as spray cans fire extinguisher refill cartridges etc in the refrigerator Maintenance and Cleaning Before cleaning always switch off the apppliance and disconnect from the electrical supply When unplugging always pull the plug from the mains socket do not pull on the cable Servicing This product should be serviced by an authorised engineer and only genuine spare parts should be used Under no circumstances should you attempt to repair the appliance yourself Repairs carried out by inexperienced persons may cause injury or serious malfunctioning Contact your local Service Force Centre At the end of the Appliance Life When disposing of your appliance use an authorised disposa
7. e close fitting of the bulb against the rubber seal in the socket When moving the cabinet lift it by the front edge to avoid scratching the floor Cae ME D 7 LD All an AO i Zanussi 818 14 54 01 1 When the appliance is not in use Disconnect the appliance from electricity supply Empty all foods and clean the appliance leaving the doors ajar to prevent unpleasant smells Before contacting your local Service Force Centre check the following points Symptom Solution The temperature is too high inside the Set a lower temperature refrigerator Put food products in the right place inside the refrigerator See the chapter Temperature inside the refrigerator Distribute the food products to allow cold air to circulate around them Make sure that the door is completely closed and that the insulating strip is complete and clean It is too cold inside the refrigerator Set a higher temperature Vegetables and other products that are easily frozen have been placed on a too cold shelf See the chapter To start the fridge and thermostat control There is water on the cooling plate inside This is normal During automatic geirostng frost thaws on the the refrigerator cooling plate Water is running inside the refrigerator Clean the water drain and drain hole inside the refrigerator using e g cotton swabs or a bottle cleaner brush Food products could
8. e removed The lower door compartment and the glass shelf above the vegetable drawer must not be moved They are required for proper air circulation inside the cabinet Shelves with a raised edge should be placed with the raised edge facing the rear wall of the cabinet and thus prevent food products from touching the cooling plate Zanussi 818 14 54 01 1 A nn Normal Operating Sounds e You may hear faint gurgling or bubbling sounds when the refrigerant is pumped through the coils or tubing at the rear to the cooling plate evaporator e When the compressor is on the refrigerant is being pumped round and you will hear a whirring sound or pulsating noise from the compressor e A thermostat controls the compressor and you will hear a faint click when the termostat cuts in and out Food Storage e To obtain the best results from your appliance neither hot foods nor liquiuds which may evaporate should be placed in the larder compartment e Keep the time between buying chilled food and placing it in your fridge as short as possible e Do not push food together too much try to allow air to circulate around each item e Do not store food uncovered Remove suspect food from you refrigerator and clean refer to cleaning and maintenance al nn Energy Saving Advice Do not install the cabinet close to sources of heat such as a cooker dishwasher or radiator Locate the appliance in a cool wel
9. edge of the glass shelf and pull the shelf and transport support forward until the shelf tilts and the transport support can be removed Some models are fitted with a silencing pad under the cabinet Do not remove this pad Installing the cabinet To otain the best performance from the cabinet ensure e the cabinet is placed in a dry cool place and is not exposed to direct sunlight e the cabinet is not placed close to a source of heat e g a cooker or dishwasher e the room in which the cabinet is placed has a temperature of 10 C to 32 C e the cabinet is level The cabinet should not lean against any wall If necessary adjust the feet using the supplied adjustment spanner e there is good air circulation around the cabinet and that the air channels below and behind the cabinet are not blocked The ventilation space above the cabinet and any grocery top cabinet must be at least 200 cm2 The ventilation space can either be a directly above the cabinet or b behind and above the top cabinet In this case the space behind the cabinet must be at least 50 mm deep If the cabinet is placed in a corner and the side with the hinges faces the wall the distance between the wall and the cabinet must be at least 10 mm to allow the door to open enough so that the shelves can be removed 12 Zanussi 818 14 54 01 1 Electrical connection A Any electrical work required to install this appliance should be carried out by a qualified ele
10. have been placed stopping the water from running into the drain Water comes out on the floor Place the drain hose at the back of the cabinet above the drain bowl See the chapter Before use The compressor operates continuously Set a higher temperature Make sure that the door is completely closed and that the insulating strip is complete and clean The cabinet does not operate at all Cooling or interior light does not operate No indicator lamps light The power plug is not properly connected The fuse has blown The cabinet is not switched on Power does not reach the cabinet Try connecting another electrical device to the power outlet See Normal operating Sounds page 7 If after above checks there is still a fault call your local Service Force Center In guarantee customers should ensure that the above checks have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown Please note that proof of purchase is required for in guarantee service calls 9 Zanussi 818 14 54 01 1 In the event of your appliance requiring service or if you wish to purchase spare parts please contact your local Zanussi Service Force Centre by telephoning 08705 929929 Your call be routed the Service Force Centre covering your post code area The address of your local Service Force Centre is detailed in the accompanying Customer Care Book Before calling ou
11. he drip channel inside the fridge at regular intervals and ensure that the drip channel is clear at all times If blocked carefully clear using a piece of flexible curtain wire inserted into the drain outlet to remove the blockage External Cleaning Wash the outer cabinet with warm soapy water Remove the ventilation grille see the section Removing the ventilation grille and vacuum clean under the cabinet Once or twice a year dust the condenser black grille and the compressor at the back of the appliance with a brush or vacuum cleaner as an accumulation of dust will affect the performance of the appliance and cause excessive electricity consumption Defrosting the fridge The fridge is defrosted automatically every time the compressor stops Frost formation can be prevented by e not putting warm foodstuff inside the cabinet e avoiding frequently opening the door or keeping it open too long e not placing foodstuffs directly against the cold cooling plate To Change the Light Bulb The light is switched on automatically when the door is opened Before replacing the light bulb disconnect the power plug from the outlet Press the spring together and push the grille downward at the same time Use a bulb of the same type E14 socket maximum rating of 25 W When replacing the light bulb use a bulb of the same type as the original one The glass must measure at least 18 mm in diameter at the socket This will ensur
12. l site Remove the plug and ensure that any locks or catches are removed to prevent young children being trapped inside Do not let sharp objects come into contact with the refrigerating system on the back of and inside the cabinet If the refrigerating system is punctured the cabinet will be damaged and foodstuff inside may spoil If the refrigurant circuit should become damaged avoid open flames and sources of ignition thoroughly ventillate the room in which the appliance is situated Do not place carbonated or fizzy drinks in the freezer compartment Bottles and cans must not be placed in the freezer compartment they can burst when the contents freeze Zanussi 818 14 54 01 1 Instructions for the user Important Safety Instructions 2 Description of the Apliance 4 Control Panel toy vortex vee ra 4 Usa ut a aida o A Ane ere e A a yh eee tes 4 Before USE nern 5 To start the fridge and thermostat control 5 Measuring the temperature 6 Switching off AAA 6 Cabinet inferior arca 6 Hints and Tips oooooooo 7 Normal Operating Sounds o oo ooooo om 7 Food Storage cece ensure 7 Energy Saving Advice 0 0 cee ee eee 7 Maintenance and Cleaning 7 Removing the ventilation grille 7 Internal Cleaning icon ewes eee 8 External Cleaning Sense 8 Defrosting the fridge u an 8 To Change the Light Bulb 8
13. l ventilated room and make sure that the air openings of the cabinet are not obstructed Always leave warm food to cool down to room temperature before placing in the fridge Try to avoid keeping the door open for long periods or opening the door too frquently as warm air will enter the cabinet and cause the compressor to switch on unnecessarily often Ensure there are no obstructions preventing the door from cloosing properly It is advisable to periodically clean the refrigeration system at the back of the appliance with a duster or vacuum cleaner Le A Before any maintenance or cleaning work 1s carried out DISCONNECT the appliance from the ELECTRICITY supply Removing the ventilation grille The ventilation grille can be removed e g to wash the grille Make sure the door is open when removing the ventilation grille Unsnap the upper edge of the grille by pulling outward downward Then pull the grille straight out to completely remove it Zanussi 818 14 54 01 1 Internal Cleaning Clean the inside and the accessories with warm water and bicarbonate of soda 5 ml to 0 5 litre of water Rinse and dry thoroughly Do not use detergents abrasive powders high perfumed cleaning products wax polishes or cleaning products containing bleach or alcohol Regulary check the door seals and wipe clean to ensure they are clean and free from debris Discconnect the appliance from electricity supply Clean out t
14. lock when it is laid down It will be easier to grip under the cabinet when returning to an upright positon 4 On the upper part of the cabinet Put the hinge pin on the other side 5 On the lower part of the cabinet Unscrew the hinge Move the hinge pin and plastic cover Secure the hinge on the other side Raise the cabinet and replace the ventilation grille 6 Unscrew the handle Carefully press in the plastic plugs on the opposite side using a punch Secure the handle in the plug holes Then press the supplied plastic plugs into the holes to which the handle was previously fitted 7 Put the cabinet in position Check that it stands straight See the section Positioning the cabinet 14 Zanussi 818 14 54 01 1 MARIESTAD DD EH
15. rea e The product is installled and used in accordance with our instructions and is only used domestically i e a normal household e The product is installed and taking into account regulations in your new country Before you move please contact your nearest Customer Care Centre listed below to give them details of your new home They will then ensure that the local Service Organisation is aware of your move and able to look after you and your appliances France Senlis 33 0 3 44 62 22 22 Germany N rnberg 49 0 911 323 26 00 Italy Prodenone 39 0 1678 47053 Sweden Stockholm 46 0 20 78 77 55 UK Slough 44 0 1753 21 98 97 This figure is based on standard test resultd to the European Standard EN153 Actual consumption will depend on how the appliance is used and where it is located Unpacking Unpack the cabinet and check that it is in good condition and free of any transport damage Notify the dealer immediately of any damage Hand the packaging over for recycling A Do not allow children to play with the packaging The plastic film can cause suffocation 1 Zanussi 818 14 54 01 1 Removing the transport supports Remove the tape and the transport supports from e the door sides e inside the door hinges e the shelves Remove the transport support on the glass shelf by pushing the support forward along the edge of the shelf until it stops at the protuberance of the shelf Take hold of the rear
16. rvice work under this guarantee must be undertaken by a ZANUSSI SERVICE CENTRE e Any appliance or defective part replaced shall become the company s property e This guarantee is in addition to your statuory and other legal rights Home visits are made between 8 30am and 5 30pm Monday to Friday Visits may be available outside these hours in which case a premium will be charged Exclusions This guarantee does not cover e Damage or calls resulting from transportation improper use or neglect the replacement of any light bulbs or removable parts of glass or plastic e Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside the United Kingdom eAppliances found to be in use within a commercial enviroment plus those those which are subject to rental agreements e Products of Zanussi manufacture which are not marked by Zanussi 10 Zanussi 818 14 54 01 1 European Guarantee If you should move to another country within Europe then your guarantee moves with you to your new home subject to the following qualifications e The guarantee starts from the date you first purchased your product eThe guarantee is for the same period and the same extent for labour and parts as exists in the new country of use for this brand or range of products eThis guarantee relates to you and cannot be transferred to another user eYour new home is within the European Community EC or European Free Trade A
17. t an engineer please ensure you have read the details under the heading Something Not Working and have the model number and purchase date to hand Please note that it will be necessary to provide proof of purchase for any in guarantee service calls In guarantee customer should ensure that the checks under the headning Something Not Working have been made as the engineer will make a change if the fault is not a mechanical or electrical breakdown For general enquiries concerning your Zanussi appliance or futher information on Zanussi products you are invited to contact our Customer Care Department by letter or phone as follows Customer Care Department Zanussi 55 77 High Street Slough Berkshire SL1 1DZ Phone 08705 727 727 HOES Standard Guarantee Conditions We undertake that if within 12 months of the date of the purchase this appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials we will at our option repair or replace the same FREE OF CHARGE for labour materials or carriage on condition that e The appliance has been correctly installed and used only on the electrical supply stated on the rating plate e The appliance has been used for normal domestic purposes only and in accordance with the manufacturer s instructions e The appliance has not been serviced maintained repaired taken apart or tampered with by any person not authorised by us e All se
Download Pdf Manuals
Related Search