Zanussi FM 16 Use & Care Manual
Contents
1. 10 Using the lower oven Preheat the oven arrange the food in the oven shut the door and turn the selector knob Fig 8 to symbol 8 turn then the temperature regulator knob Fig 9 to the required temperature By turning the selector knob to position the oven light will come on this operation will also maintain the general control light on until the knob is turned again to position 0 The cooking positions of the temperature regulator knob Fig 9 are the positions from 50 to MAX and give a full range of temperatures The oven temperature light will come on and will remain on until the oven has reached the correct temperature after that it will come off and on showing how the temperature is being maintained When the oven control reaches the bottom element comes on and a max temperature of 280 C can be obtained When the oven control reaches O the top element comes on and a max temperature of 260 C can be obtained These settings are particularly useful for finishing food either only on the top or the bottom During cooking the door should be opened as little as possible to avoid heat loss and so excessive electricity consumption Fig 10 Using the grill The grill is located in the lower oven As with the oven the grill control can be set to a number of different heats Fig 8 At MAX position the maximum temperature is obtained Foods to be grilled are placed on the wire gr2. and TV interference The upper oven has a heating element rated at 2500W The lower oven ratings are as follows Lower element 1000 W Upper element 1000 W Grill element 2000 W The oven has an easily accessible terminal block which is marked as follows Letter L Live terminal Letter N Neutral terminal Earth The cable used must be of the three core type with a min cross section of 2 5 mm In order to connect it to the oven it is necessary to remove the hatch at the back of the oven to reach the terminal block For direct connection to the mains supply a two pole switch with a minimum rating of 19 A and a minimum distance of 3 mm between its contacts must be fitted between the supply and the appliance This switch must not break the yellow green earth cable at any point The appliance must be earthed Important After installation and connecting the cable must be placed so that it cannot at any point reach a temperature more than 50 C above the ambient temperature ld the appliance is connected check that the main fuse and the domestic installation can support the load the power supply is properly earthed the double pole switch used to connect the appliance to the supply is easily accessible after installation Use and care When the appliance is first installed Once the appliance is installed the protective materials which were put on in the factory must be removed The plastic film covering some
3. external parts can be removed by wiping with a cloth dipped in methylated spirit Other protective materials will burn off if the controls of the ovens are turned to MAX and then let the ovens to run empty for 30 minutes This will also remove any unpleasant smells The FM 16 consists of two ovens The upper oven is evenly heated throughout A fan in the back wall distributes heated air round the food during cooking so that everything cooks in the same time regardless of where it is placed in the oven or how much is being cooked Foods of different types provided they require the same cooking temperature can be cooked together and there is no possibility of any flavours or smells being transmitted from one food to another This is the Zanussi cuisinair system Cooking can be manual or automatic with or without the programmer The programmer includes an analogue clock a minute minder and controls by which the upper oven can be set to come on and go off unattended The lower oven is a conventional one and contains a grill The grill is controlled by a thermostat adjusting the selected temperature By positioning the grill on MAX the max temperature is obtained The dials above each control knob show when the oven is switched on whilst the indicator lights show the behaviour of the thermostat during cooking A light comes on inside the oven when it is switched on and remains on until the oven goes off
4. liquid overflowings To make thorough cleaning of this panel easier you can extract it from the bottom by pulling it up If you use an oven spray cleaner be careful not to spray it on the oven fan and on the thermostat feeler Cleaning the lower oven The oven interior is made of a strong vitreous enamel and therefore can be cleaned with any normal caustic oven cleaner Remove by pulling out the infrared grill Fig 15 and put the safety plug into the grill socket Fig 15 Remove the side runners as described for the upper oven Important Please take care to follow the oven cleaner manufacturer s instructions precisely Care must be taken to ensure that the oven cleaner does not come into contact with the aluminium and painted surfaces of the appliance Replacing appliance components Prior to undertaking any maintenance work or replacing the oven lamp or grill heating element be sure to disconnect the appliance from the electric supply 1 Control Knobs These can be removed by pulling them out 2 Oven lamp replacement Unscrew glasscap Fig 16 and replace burnt out bulb with one that resists to high temperatures 300 C Electric bulb 15W 240V 50Hz 300 C E14 Removing the oven door To thoroughly clean the oven you should remove the door by proceeding as follows 1 With the aid of a coin turn the oven door stops catches 45 to the right 2 Raise the do
5. setting When the control reaches X amp Y the oven temperature light will come on also an internal oven light This setting is NOT a cooking position but is intended for rapid thawing of frozen food Positions from 50 C to MAX are cooking positions and give a full range of temperatures The oven temperature light will come on until the oven has reached the correct temperature after that it will come on and off showing how the temperature is being maintained Fig 6 N NS TS INK N XN gt 5 Cooking automatically The upper oven cooks automatically when the programmer is set to switch it on and off at the times given without the need for anyone to be in attendance Most foods cook well automatically but preference should be given to those which will not be affected by the waiting period before the oven comes on Electric programmer The function of the programmer is to turn on and off automatically the upper oven s heating element and thus to change the preset cooking time as one pleases The programmer features an electric clock indicating the hour and the day and a minute minder with a sound signaling device Operation of the programmer The figure 7 shows the controls of the electric programmer Knob A START By depressing and turning this knob the C hand is set on the cooking start time Knob B U By turning this knob anticlockwise or clockwise it prearranges cooking duratio
6. the surround or cabinet into which the oven will be built are correct and that proper arrangements are made for a continuous supply of air to the oven so it does not overheat Fig 1 Dimensions of the recess for building into a kitchen unit mm 560min Fig 2 Important To ensure an efficient ventilation it is necessary to leave the vents provided at the bottom of the oven clear Securing the oven to the cabinet Fit the appliance into the cabinet recess Open the oven door and secure the oven to the kitchen cabinet with six wood screws which fit exactly the holes provided in the oven frame Fig 3 Cooling fan The cooling fan is designed to cool the oven housing and the components of the oven itself The fan switches on automatically when either of the oven control knobs are turned on Cool air is drawn in through the vents at the bottom of the oven to cool the oven and housing by absorbing the residual heat This warm air is then blown out through the venting grille incorporated in the upper oven door handle mechanism Fig 3 The manufacturer disclaims any Connecting to responsibility should these safety electricity instructions not be carried out This appliance meets the requirements laid down in EEC Directive No 82 499 The oven is designed to be connected to dated 7 6 82 relating to the suppression of 240V 50 Hz electricity supply radio
7. Fr ZANUSSI Instructions for the use and care of FM 16 built in double oven It is most important that this instruction book should be retained with the appliance for future reference Should the appliance be sold or transferred to another owner or should you move house and leave the appliance always ensure that the book is supplied with the appliance in order that the new owner can be acquainted with the functioning of the appliance and the relevant warnings Warnings Built in ovens THESE WARNINGS ARE PROVIDED IN THE INTEREST OF SAFETY YOU MUST READ THEM CAREFULLY BEFORE INSTALLING OR USING THE APPLIANCE This appliance is designed to be operated by adults Children should not be allowed to tamper with the controls or play with the product Any installation work must be undertaken by a qualified electrician or competent person It is dangerous to alter the specifications or modify the product in any way This appliance should be serviced by an authorised Zanussi Network Service Centre and only genuine Zanussi spare parts should be used e Cookers can become very hot with use and retain their heat for a long period of time after use Children should be supervised at all times and should not be allowed to touch the hot surfaces or be in the vicinity when in use or until the appliance has cooled after use e Always ensure that the control knobs are in the off position when not
8. If the sound signal is not interrupted it will do so automatically after approximately 10 minutes Example of programmer setting for automatic operation of the oven Cooking start time 17 00 hours Cooking duration 90 minutes max 180 minutes Pressin and turn knob A setting the C hand on 5 corresponding to 17 00 hours Turn knob B setting dial D to 90 Turn the oven control knob Fig 5 to the desired temperature level After carrying out the above settings the oven will operate automatically from 17 00 hours to 18 30 hours i e for 1 hour and 30 minutes Minute minder The programmer will act as a minute minder only if no automatic cooking is programmed and the oven is not turned on To operate the minute minder turn knob B clockwise and set on dial D the required cooking time The maximum allowed cooking duration is 180 minutes To stop the sound signal turn knob B until the 0 symbol coincides with the index of dial D Programmed cooking Programmed cooking is no different to normal cooking The programmer controls the selected cooking time while one may be busy doing other things therefore when cooking is carried out automatically it s preferable to cook food which does not require particular attention Attention If at the end of the programmed cooking time the oven remains still in operation it will be necessary to re program it again or carry out cooking by setting up the minute minder
9. The internal dimensions are Top oven Bottom oven Height 320 mm 185 mm Width 420 mm 420 mm Depth 390 mm 400 mm Capacity 53 0 litres 31 litres Electric programmer Oven general control light Lower oven selector knob Lower oven temperature regulator knob Lower oven temperature light Upper oven temperature light Upper oven control knob Fan Removable shelf runners Removable grease filter Upper oven Lower oven m Dripping pan large n Reversible grill pan insert o Removable handles 2 Off Fig 4 7 Using the upper oven As soon as the oven is switched on the fan starts and runs until the oven control is switched off again Fig 5 The food should be put into the oven before switching on even when cooking manually the speed of heating up is so fast that there is no need to preheat The oven shelves can be fully filled Most normal types and materials of cooking utensils can be used During cooking the door should be opened as little as possible to avoid heat loss and so excessive electricity consumption Important The anti tip oven grid must be positioned as shown in figure 6 Cooking manually When cooking manually ensure that the programmer is not in operation accidentally If this is not the case and you do not want to use the automatic programmer return the control to the manual position Arrange the food in the oven shut the door and turn the oven control Fig 5 to the required temperature
10. ay damage them The parts in stainless steel after their cleaning are to be dried with chamois leather Never use abrasive scourers or steel wool muriatic acid or other abrasive cleaners which may scratch the finish The enamelled and glass parts should not be cleaned while they are still warm Grease filter upper oven This filter protects the fan from fat splashes it should always be cleaned after roasting has taken place As it is stainless steel you can safely wash it in a dishwasher Install the grease filter only when roasting fat meats Removing the grease filter Fig 11 To remove the filter proceed as follows pull up the protruding tongue and then pull the filter outwards removing it from the rear panel 12 Removing and cleaning the oven panels Supplied on request If you wish to remove lateral and upper panels proceed as follows Remove the upper panel unscrew the fixing ring nuts of the side runners Fig 12 Remove the runners and the panels Fig 13 If necessary you can also remove the back panel but in this case you have also to disconnect the electricity supply Unscrew the panel fixing screws by means of a screwdriver Fig 14 In order to protect the upper oven the appliance features an enamelled panel suitably shaped to contain possible
11. from a source outside of the receiver ZANUSSI 5 YEAR COVER CONDITIONS For a once only payment you can extend your Standard Guarantee to 5 years All the conditions and exclusions of the Standard Guarantee apply Notes 1 Products supplied as seconds refurbished damaged or shop soiled are not eligible for Zanussi 5 year cover 2 The issue of a cover does NOT by virtue of our having done so nullify the exclusions 3 The Engineer will need to check the details of your Cover card and may make a charge for his services if it is not presented to him at the time of his call 4 The date of purchase or the date of initial payment deposit of the appliance will be deemed the date of commencement of cover 5 Covers issued are not refundable or transferable ZANUSSI The appliance of science R1280
12. id in the grill pan which can be adjusted on the side grids either upwards or downwards to give the required distance from the element For foods which require a longer grilling the grill pan has to be set on the lower positions Important Because the grill element is in the top of the lower oven the door must be opened when grilling This means that the escaping heat from the grill could overheat the upper oven door and the control panel so to prevent this happening it is essential that the heat deflector provided to protect the rest of the appliance is in place before the grill is switched on The deflector is put in place as shown in Fig 10 To use the grill Open the door and put the heat deflector in position Turn the oven selector knob Fig 8 to E an then set the grill regulator knob Fig 9 to the heat setting required A little use and practice will soon show which heat setting is the best for the individual user When grilling is over remove the heat deflector and shut the door 11 Maintenance and cleaning Important The electricity supply must be switched off before undertaking any maintenance operation The oven will have a longer life if it is frequently cleaned thoroughly paying special attention to the following The cleaning should not be carried out when the oven is still warm The enamelled parts should be cleaned with lukewarm water and soap without using abrasive scourers which m
13. in use For hygiene and safety reasons this appliance should be kept clean at all times A build up of fats or foodstuffs could result in a fire This appliance has been designed for cooking edible foodstuffs only and must not be used for any other purposes Never line any part of the oven with aluminium foil Easy clean liners should never be cleaned with any other than soapy water see cleaning instructions Before any maintenance or cleaning work is carried out on the appliance always turn off the isolator switch at the cooker point and allow to cool e Ensure that the anti tip oven shelves are put in place in the correct way see instructions e Under no circumstances should you attempt to repair the appliance yourself Repairs carried out by inexperienced persons may cause injury or more serious malfunctioning Refer to your local Zanussi Service Centre Always insist on genuine Zanussi spare parts Contents Building in Connecting to electricity Use and Care Using the upper oven Using the lower oven Using the grill Maintenance and cleaning What happens if something goes wrong page page page page page page page page Important the installation of the oven and connecting it to electricity must always be done by competent installers and to standards and regulations currently in force 2 Building in It is important that the dimensions and materials of
14. n on dial D up to 3 hours When pulled outwards and turned clockwise or anticlockwise it enables you to adjust the clock time when installed following a power failure or due to gains or losses of clock time Upper oven manual operation The oven may be used in a normal manner that is to say without programming it In such cases the programmer s knob B must be turned clockwise until symbol N coincides with indication of dial D Furthermore the C hand must be covered by the hour hand Upper oven semi automatic operation Manual cooking start programmed i e automatic cooking stop Place the food to be cooked into the oven Turn knob B clockwise and set on dial D the number of minutes corresponding to the required cooking end Turn the oven knob Fig 5 to the required temperature setting Upper oven totally automatic cooking Place the food to be cooked in the oven Press in and turn knob A so as to set the C hand to the required cooking start time the C hand is integral with the hour hand when the oven is not in the automatic mode Turn knob B setting on dial D the required cooking duration Turn the oven control knob Fig 5 to the required temperature setting When the cooking time is up a sound signal will indicate that cooking is over To stop the sound signal turn knob B clockwise until the 0 symbol appears on dial D In this position the oven is disconnected from the electric supply
15. or to the limit stop and pull it out in a forward direction Fig 17 Grasp the door on the two sides don t pull it by the handle To re install the door 1 Insert the door into the oven with its two brackets 2 Open the oven door and return the door stops catches to their original position 14 What happens if something goes wrong Important If the ovens do not come on when cooking manually first check that the fault is with both ovens it may be that if it is the upper one only that is affected there is probably a simple answer the programmer is set to automatic to set it to manual turn the control knob to the required position If this is not the answer then check that the appliance is connected correctly check that the switch from the supply to the appliance is ON replace the fuse in the socket where present with another of the appropriate rating check that the fuse in the fuse box is intact If after all these checks the appliance still does not work call your local Zanussi Network service centre listed in the telephone directory It helps to jot down the address and telephone number in the space below ZANUSSI STANDARD GUARANTEE CONDITIONS This guarantee is in addition to your statutory and other legal rights which will not be excluded or in any way diminished by the return of the guarantee card We Zanussi Limited undertake that if within twelve months 24 months for TV set
16. s of the date of the purchase this ZANUSSI appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials we will at our option repair replace the same FREE OF ANY CHARGE for labour materials or carriage on condition that The appliance has been correctly installed and used only on the electricity supply stated on the rating plate The appliance has been used for normal domestic purposes only and in accordance with the manufacturer s operating and maintenance instructions The appliance has not been serviced maintained repaired taken apart or tampered with by any person not authorised by us The appliance is still in the possession of the original purchaser All service work under this guarantee must be undertaken by a Zanussi Network Service Centre or the Zanussi Authorised TV Service Dealer Any appliance or defective part replaced shall become our property Exclusions This guarantee does not cover Damage or calls resulting from transportation improper use or neglect the replacement of any light bulbs or removable parts of glass or plastic Costs incurred for calls to put right machines improperly installed or calls to machines outside the UK and the Republic of Ireland Appliances found to be in use within a commercial environment plus those which are the subject or rental agreements Television receivers routine adjustment or poor reception resulting
Download Pdf Manuals
Related Search