Zanussi FBi 624 Instruction Manual
Contents
1. Remove the bottom drip tray unscrew the ring nuts securing the side grilles Fig 12 remove the grilles and then remove the side panels after sliding them out of their retaining pins Fig 13 Pull out the grill heater Fig 14 and the top panel Warning Before removing the back panel the oven must be disconnected and the safety plug put into the grill socket Fig 14 To remove the back panel use a screwdriver Fig 15 This is a good opportunity to clean the back of the rear panel When using an oven aerosol never spray in the direction of the fan or against the thermostat sensor 15 Replacing appliance components Prior to undertaking any maintenance work or replacing the oven lamp or grill heating element be sure to disconnect the appliance from the electric supply Replacing the oven light Unscrew the ring nuts securing the right side grille Fig 12 Remove the grille and then remove the right side panel after sliding it out of its retaining pins Prise the glass protection off as shown in Fig 16 Replace the bulb with a new one suitable for high temperature 300 C and having the following technical features 240V 50Hz 300 C E14 3 x 15W Important When re fitting the glass protection be sure the smooth surface is on the outside of the lampholder 16 Cleaning the oven door To ensure thorough cleaning of the oven door it is advisable to dismantle it as follows Open the door a2. ZANUSSI Instructions or the use and care of FBI 624 Cuisinair built in cooker Contents Fitting in Direction Connecting to electricity Use and care Using the oven Using the grill The electronic programmer Cleaning What happens if something goes wrong Page Page Page Page Page Page 9 Page 14 Page 18 Co OC Sd OO wo Important The installation of the oven and connecting it to electricity must always be done by competent installers and to standards and regulations currently in force To the installer The following instructions are to be followed by a competent installer to ensure that all the installation adjustments and maintenance operations are in accordance with existing rules and regulations These instructions only cover the electric oven Separate instructions for the gas hob are to be found in the relevant handbook Important Before servicing the appliance or undertaking any maintenance work be sure to disconnect the oven from the electric supply Should it be absolutely necessary to keep the appliance live take all possible precautions to prevent accidents Oven dimensions Fig 1 Fitting in directions The appliance consists of an electric oven with the controls for a gas hob To ensure satisfactory performance of the appliance the dimensions in millimetres of the housing should be adhered too see Fig 2 Attention should be made to the fact that the o
3. Removable grill element Removable oven liner panels Removable grease filter m Fan Removable shelf runners Dripping pan large Reversible grill pan insert Removable handles 2 off When the oven is first installed Once the oven is installed it is important to remove the protective materials which were put on in the factory Remove from these parts the plastic film then wipe with a cloth dipped in methylated spirit Then switch the oven control to MAX and leave it to run empty for 30 minutes to burn off any other protective materials This will also remove any unpleasant new smells The oven is evenly heated throughout A fan in the back wall distributes heated air round the food during cooking so that everything cooks in approximately the same time regardless of where it is placed in the oven or how much is being cooked Foods of different types provided they require the same cooking temperature can be cooked together and there is no possibility of any flavours or smells being transmitted from one food to another The oven has a removable grill Cooking by either oven or grill can be manual or automatic without or with the programmer This includes a digital clock a minute minder and controls by which the oven can be set to come on and go off unattended Indicator lights on the control panel show when the oven is switched on and the behaviour of the thermostat during cooking A light will come on inside th
4. list for your nearest network centre If the product is under first year guarantee then you will be required to produce proof of date of purchase to the engineer If it is under 5 year cover then you must show your cover card to the engineer Please ensure that the enclosed pre addressed card is stamped completed in full and forwarded to IAZ International UK Ltd to enable the guarantee to be recorded Also complete the space below as your own record of the guarantee GUARANTEE RECORD Appliance purchased from Guarantee card no Serial no Your name on Model no These details may be taken from your Guarantee Record Card Address C kfVCCoo Oe A aaa aaa aaa aaa aaaaasaauaaaasaeaaasasasasasasasasaaululuuslususunun 27296 9140 9101112 86
5. for your local Zanussi network service centre listed in the telephone directory It helps to jot down the name and address and telephone number in the space below 18 ZANUSSI GUARANTEE CONDITIONS This guarantee is in addition to your statutory and other legal rights which will not be excluded or in any way diminished by the return of the enclosed card We IAZ International UK Ltd guarantee that if within twelve months of the date of the purchase this ZANUSSI appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials we will at our option repair or replace the same FREE OF ANY CHARGE for labour materials or carriage on condition that e The appliance has been correctly installed and used only on the electricity supply stated on rating plate e The appliance has been used for normal domestic purposes and in accordance with the manufacturer s operating and maintenance instructions e The appliance has not been serviced maintained repaired taken apart or tampered with by any person not authorised by us e The appliance is still in the possession of the original purchaser e Any appliance or defective part replaced shall become our property This guarantee does not cover any damage caused during transportation or the replacement of any light bulbs or removable parts of glass or plastic Should you require service on your Zanussi appliance consult the enclosed
6. e oven when it is switched on and remain on until the oven goes off The grill cannot be used at the same time as the oven The internal dimensions of the oven are height 3820 mm width 420 mm depth 390 mm volume 53 0 lt Assembly of front parts To assemble the front parts which come in different colour versions follow instructions provided in the kit Using the oven As soon as the oven is switched on the fan starts and runs until the oven control is switched off again Fig 7 The food can be put into the oven before switching on even when cooking manually the speed of heating up is so fast that there is no need to preheat The oven shelves can be fully filled Most normal types and materials of cooking utensils can be used During cooking the door should be opened as little as possible to avoid heat loss and so excessive electricity consumption Gas hob control knobs The front panel also includes the control knobs for operation amp adjustment of the hob s four gas burners Fig 8 To automatically light the hob burners after turning the relevant control knob to max simply depress the special lighting button marked by a small spark symbol Cooking manually When cooking manually ensure that the programmer is not in operation accidentally Check that the pilot light 3 Fig 9 is off If not so and you do not want to use the automatic programmer depress the button C Fig 9 Arrange the f
7. hes too high a level Once the temperature has returned to a safe level the main oven thermostat will function In cases where there is a permanent failure it is necessary to contact the Zanussi Network Service Engineer Electronic programmer The programmer performs the following functions presetting of cooking time when using the oven it shows the correct time of the day it shows the temperature measured by the food probe when auto cooking Fig 9 shows the programmer controls Controls Pushbuttons To enter and display the p O A cooking duration To enter and display the end of O B cooking time C Manual non automatic operation D To enter the temperature for cooking with the food probe Knob To enter the various cooking O E times amp temperatures turn either clockwise or counterclockwise Pilot lights The triangular pilot lights located above the control pushbuttons amp knob light up to indicate that the selected function is being performed Operating the electronic programmer This is a 24 hour clock showing the hours from 1 through 24 and the minutes from 0 through 60 When the appliance is connected to the electric supply for the first time or after a power failure the digits and pilot lights triangles 1 amp 2 of the display will blink to indicate that the clock needs to be set Proceed as follows to enter the correct time of the day depress simultaneous
8. ifficult to register a correct finish temperature 5 Select the cooking temperature by means of the control knob The oven comes on 6 The probe temperature registered before the commencement of cooking will be 30 C The probe will register the internal meat temperature throughout the cooking period and convey the information to the programmer This will give a visual read out as cooking continues and switch off the supply when the selected temperature has been reached The digits in the display start blinking and the buzzer sounds for about two minutes Turn the oven control knob Fig 7 to 0 Open the oven door remove the probe from the meat extract the probe pin from the socket and replace with the plug Use a kitchen glove to prevent skin burns When the temperature probe is disconnected the display digits and pilot light 4 go out At no time it is necessary to weigh the meat the sensor determines the cooking time However the cooking time is obviously influenced by the cooking temperature Power cuts In case of a power cut lasting more than 1 6 seconds all data stored in the programmer are cancelled When the power returns the digits in the display start blinking to remind you that it needs to be set 13 Cleaning After every meat roasting clean the oven panels as soon as they have cooled so that any fat splashes are removed After use wipe over the rest of the oven with a cloth wrung out in liq
9. inal Letter N Neutral terminal Earth The cable used must have a cross section of at least 2 5 mm For direct connection to the mains supply a double pole switch with a minimum rating of 11 A must be fitted between the supply and the appliance This switch must not break the yellow green earth cable at any point For plug and socket connection the plug must have a minimum rating of 11 A The appliance must be earthed Important after installation and connecting the cable must be placed so that it cannot at any point reach a temperature more than 50 C above the ambient temperature Before the appliance is connected check that the main fuse and the domestic installation can support the load the power supply is properly earthed the double pole switch used to connect the appliance to the supply is easily accessible after installation The manufacturer disclaims any responsibility should these safety instructions not be carried out This appliance meets the requirements laid down in EEC Directive No 82 499 dated 7 6 82 relating to the suppression of radio and TV interference Use and care n O p q Electronic programmer Oven temperature light Oven general control light Rear left cooking plate control knob Front left cooking plate control knob Gas burners electronic lighting button Front right cooking plate control knob Rear right cooking plate control knob Oven and grill control knob
10. ly pushbuttons A amp Q B and turn knob E as required until the correct hour amp minutes are entered The electronic clock starts running when you release pushbuttons A amp A B pilot lights 1 amp 2 go out and pilot light 3 will start blinking To put the pilot light 3 out depress pushbutton C Setting the minute minder with sound signal buzzer The minute minder can be used only with the programmer set on manual operation pushbutton C depressed The maximum programmable time for the buzzer to sound is 28 hours and 59 minutes Proceed as follows to set the minute minder depress pushbutton C pilot light 3 goes out depress pushbutton A and at the same time turn knob E to enter the required time pilot lights 1 and 3 turn on Release pushbutton A When the programmed time is up the buzzer will sound for 2 minutes unless it Pete de by depressing pushbutton Q A pilot light 1 goes out and pilot PA 3 will start blinking To put the pilot light 3 out depress pushbutton C Semi automatic operation of the oven It is possible to start cooking immediately and to program the duration of the cooking process The maximum programmable cooking duration is 23 hours and 59 minutes Place the food to be cooked into the oven then turn the relevant knob Fig 7 to the desired setting Now proceed as follows depress pushbutton A and keeping it dep
11. ood in the oven shut the door and turn the oven control to the required temperature setting When the control reaches lt the oven temperature light will come on also an internal oven light This setting is NOT a cooking position but is intended for rapid thawing of frozen food Positions from 50 C to MAX are cooking positions and give a full range of temperatures The oven temperature light will come on and will remain on until the oven has reached the correct temperature after that it will switch on and off showing how the temperature is being maintained Cooking automatically The oven or grill can cook automatically when the programmer is set to switch it on and off Most foods cook well automatically but preference should be given to those which will not be affected by the waiting period before the oven comes on Using the grill At the thermostat controlling the heat does not operate and the element stays on continuously to give the highest heat possible The grill can be operated by the electronic programmer Foods to be grilled are placed on the wire grid in the grill pan which can be curved either upwards or downwards to give the required distance from the element Important To spare energy the oven door must be closed during grilling Safety thermostat Should the main oven thermostat fail the oven is protected by a safety thermostat which will operate if the temperature within the oven reac
12. ressed enter the required cooking duration with knob E when you release pushbutton A pilot lights 1 amp 8 will remain alight to show that the cooking programme is being carried out At the end of the cooking process the buzzer will sound At the same time pilot light 1 goes out and pilot light 3 will start blinking to put it out depress pushbutton C 11 Automatic operation of the oven Cooking can be started and finished automatically The maximum programmable cooking duration is 23 hours and 59 minutes After preparing the food turn the oven control knob Fig 7 to the required setting and then proceed as follows depress pushbutton 2 A and keeping it depressed enter the required cooking duration with knob E when you release pushbutton 2 A pilot lights 1 amp 3 will remain alight to show that the cooking programme has been accepted depress pushbutton B and keeping it depressed enter the required end of cooking time with knob E when you release pushbutton 1 B pilot lights 1 2 amp 3 will remain alight to show that the cooking programme is being carried out When cooking starts pilot light 2 goes out and at the end of the cooking programme the buzzer will sound When the buzzer stops pilot light 1 goes out at the same time pilot light 3 will start blinking to turn it off depress pushbutton C Manual non automatic operation of the oven To opera
13. s far as it will go turn the key that secures it through a 45 turn Fig 17 using a screwdriver or a coin Slide off the door Fig 17 and lay it down on a flat horizontal surface press thoroughly down the appropriate spring loaded catches A Fig 18 lift slightly up the glass B Fig 18 and remove it by pulling it forwards After having cleaned the door reassemble the glass C Fig 18 lift up hooks provided under the hinges and fit them in the oven bottom slots Reassemble the door carrying out above operations in the reverse order 17 What happens if something goes wrong Power cuts Should the electricity supply fail for any reason remember to reset the electronic clock to the right time when the power is resumed If the cooker does not come on when cooking manually first check that the programmer is set for manual push button C depressed If this is as it should be and the oven still does not come on check that it is plugged in properly check that the socket switch and or the switch from the supply to the oven are ON replace the fuse in the plug with another of the appropriate rating and check that this plug has been wired up properly check that the socket when present is supplying power do this by plugging in another appliance that is known to be working properly check that the fuse in the fuse box is intact If after all these checks the oven still does not work send
14. te manually the oven depress pushbutton C pilot light 3 goes out 12 Automatic cooking in the oven with temperature probe Follow the chart below for best roasting results The probe consists of a skewer like sensor probe at one end of a heat resistant cable and a plug at the other This device should not be submerged in water just wiped clean with a damp cloth Its method of operation is as follows 1 Remove the existing plug A Fig 10 from the probe socket which is located in the top of the left hand side of the oven 2 Insert the probe sensor probe into the centre of the joint taking care to avoid touching bone as this will give a false temperature reading 3 Place the joint in a suitable tin into the oven cavity and locate the probe connecting pin B Fig 10 into its socket C Fig 10 4 Select the finished internal meat temperature by means of the electronic programmer To do this depress pushbutton 2 D Fig 10 and keeping it depressed select the cooking temperature corresponding to the required degree of doneness see roasting chart by means of knob E when you release pushbutton pilot light 4 comes on to indicate that the programme has been accepted Roasting Chart Internal Temperatures Pork Si Well Done 85 C Beef Cn Rare 60 C Medium 70 C Well Done 80 C Chicken R Well Done 82 C as poultry is a difficult shape with a great deal of bone it is d
15. uid detergent Do not use abrasive scourers or steel wool Always wait until the oven is cool before cleaning this is particularly important where the glass oven door is concerned From time to time it will be necessary to do a more thorough cleaning When the operations described below are carried out the oven should first be unplugged or switched off from the electricity supply Important In order to keep the shining and luxurious appearance on the control panel of your appliance we recommend that it is cleaned with a soft cloth soaked in warm soapy water Should you accidentally spray an oven cleaner on the control panel this should be wiped away using a soft cloth soaked in warm water It is also important that a soft cloth only is used for cleaning Grease filter When roasting meat be sure to install the special grease filter Fig 11 to protect the fan in the rear wall of the oven from fat splashes After roasting is completed remove the grease filter and clean it thoroughly As it is stainless steel you can safely wash it in a dishwasher 14 Fig 15 Removing the grease filter Fig 11 To remove the filter proceed as follows pull up the protruding tongue and then pull the filter outwards removing it from the rear panel To remove and clean the oven panels If any build up of deposit appears on the oven lining panels they should be removed for a more thorough cleaning To do this
16. ven housing must be glued with heat resisting glue 120 C Plastics and glues not heat resisting can result in deformations and unglueing Fitting under the work top Assembly of the cooker To fit under a work top it is essential Fit the appliance into the recess that the recess dimensions indicated in Open the oven door and secure the Fig 2 are followed Figs 3 and 4 show cooker to the kitchen cabinet by four two suggested methods for fitting under wood screws through the perimeter In Fig 3 the oven is suspended on two frame holes as shown in Fig 5 and 6 crosspieces fixed to the sides of the adjoining furniture In Fig 4 the oven is floor mounted with two metal channels or angle irons supported on suitable feet Cooling fan The cooling fan is designed to cool the walls and the components of the oven itself The fan switches on automatically when the oven control knob is turned on Warm air is blown out through the aperture above the oven door handle When the oven is switched off the fan may remain on for several more minutes in order to cool the oven and kitchen cabinets properly after which it switches off automatically Connecting to electricity The oven is designed to be connected to 240V 50Hz electricity supply Maximum power rating 2600 W Oven element rating 2500 W Grill element rating 2000 W The oven has an easily accessible terminal block which is marked as follows Letter L Live term
Download Pdf Manuals
Related Search