Zanussi Cook Plate Instruction Booklet
Contents
1. ZANUSSI TABLE DE CUISSON KOOKPLATEN KOCHMULDEN H OBS INSTRUCTION BOOKLET NOTICE D UTILISATION GEBRUIKSAANWIJZING GEBRAUCHSANLEITUNG ENGLISH on 08705 727727 Installation This hob must be installed by qualified personnel according to the manufacturer s instructions and to the relevant British Standards Remove all packaging before using the hob Ensure that the electrical supply complies with the type stated on the rating plate located on the bottom of the hob Do not attempt to modify the hob in any way Child Safety This hob is designed to be operated by adults Do not allow children to play near or with the hob The hob gets hot when it is in use Children should be kept away until it has cooled Children can also injure themselves by pulling pans or pots off the hob During Use This hob is intended for domestic cooking onlly It is not designed for commercial or industrial purposes Do not use this hob if it is in contact with water Do not operate the hob with wet hands Ensure the control knobs are in the OFF position when not in use When using other electrical appliances ensure the cable does not come into contact with the hot surfaces of the hob Unstable or misshapen pans should not be used on the hob as unstable pans can cause an accident by tipping or spillage Never leave the hob unattended when cooking with oil and fats Never use plastic or aluminium foil dishes o2. INSTALLATION important Rectangular cut out size for hob This hob must be installed by qualified personnel to the relevant British Standards The manufacturer will not accept liability should the above instructions or any of the other safety instructions incorporated in this book be ignored Cut Out Size The dimensions of the cut out are given in the diagram BUILDING IN Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface It is also recommended to carry out the electrical connection to the hob as shown in diagrams 1 and 2 OUTLET FO 0764 10 Building over a kitchen unit with door Proper arrangements must be taken in designing the furniture unit in order to avoid any contact with the bottom of the hob which can be hot when in operation The recommended solution is shown in diagram 3 The panel fitted under the hob a should be easily removable to allow easy access if technical assistance is needed The space behind the kitchen unit b can be used for connections Dimensions are given in mm Fitting the hob to the worktop Before fitting the hob into the cut out an adhesive sealing gasket supplied with the hob must be fitted to the edge of the cut out It is essential that no gaps are left in this seal in order to prevent spillage near the h
3. gas and electricity supply stated on the rating plate The appliance has been used for normal domestic purpose only and in accordance with the manufacturer s instructions The appliance has not been serviced maintained repaired taken apart or tampered with by any person not authorised by us All service work under this guarantee must be undertaken by a Zanussi Service Centre Any appliance or defective part replaced shall become the Company s property This guarantee is in addition to your statutory and other legal rights Home visits are made between 8 30am and 5 30pm Monday to Friday Visits may be available outside these hours in which case a premium will be charged Exclusions This guarantee does not cover Damage or calls resulting from transportation improper use or neglect the replacement of any light bulbs or removable parts of glass or plastic Costs incurred for calls to put right an appliance which is improperly installed or calls to appliance outside the United Kingdom Appliances found to be in use within a commercial or similar environment plus those which are the subject to rental agreements Products of Zanussi manufacture which are not marketed by Zanussi European Guarantee If you should move to another country within Europe then your guarantee moves with you to your new home subject to the following qualifications The guarantee starts from the date you first purchased yo
4. the plate they may deteriora te during use and even disappear completely after a period of time This will not affect the performance of the hob It is important to note that the plate may smoke a little and produce a slightly unpleasant odour when used for the first time This is quite normal and will disappear after a few minutes Suggestions for the correct setting of the plates are given in the following table Very Gentle To keep food warm To melt butter and chocolate Gentle To prepare cream sauces stews and milk puddings or to fry eggs Boiled potatoes fresh vegetables pates soups broths pancakes or fish Slow Dried vegetables frozen food fruit boiling water or milk Larger stews meat roll fish High omelettes steaks Fast 6 Steaks escalopes and frying Hints and Tips Saucepans for use on solid plates should have several characteristics They should be fairly heavy duty e They should fit the heat area exactly or be slightly larger for efficient use NEVER smaller They should have a flat base to ensure good contact with the plate This is particularly important when using pans for high temperature frying or pressure cooking As soon as liquid starts boiling turn down the plate control knob so that it will barely keep the liquid simmering You can switch off the plate a short while before you finish cooking and the final stage will be completed on the accumulate
5. 45 mm 1040 W Rapid front right Hotplate 145 mm 1570 W Rapid front left Hotplate 180 mm 2090 W Total rating 6270 W INSTALLATION GUIDANCE INSTRUCTIONS CLEARANCES REQUIRED WHEN FITTING THE HOB WITHOUT A COOKER HOOD ABOVE FO 0812 Important safety requirements This hob must be installed in accordance with the IEE Wiring Regulations Current Edition Detailed recommendations are contained in the following British Standards Codes Of Practice B S 6172 B S 5440 Par 2 and B S 6891 Current Editions Location This hob has been registered as a Class X appliance according to Fire Risk Regulations Minimum distances detailed below must be observed The hob may be located in a kitchen a kitchen diner or bed sitting room but not in a bathroom or shower room Before making the cut out in the worktop ensure that there is a minimum distance of 55 mm between the rear edge of the hob and the wall A minimum distance of 100 mm must be left between the side edges of the hob and any adjacent cabinets or walls The minimum distance combustible material can be fitted above the hob in line with the edges of the hob is 400 mm If it is fitted below 400 mm a space of 50 mm must be allowed from the edges of the hob The minimum distance combustible material can be fitted directly above the hob is 700 mm INSTALLATION GUIDANCE INSTRUCTIONS CLEARANCES REQUIRED WHEN FITTING THE HOB WITH A COOKER HOOD ABOVE I 600 mm FO 0813
6. d heat Similarly stews etc cooked in well covered saucepans cook at lower temperature which is more economical Ensure pans are large enough to avoid l liquids being split onto the plates Never leave the plates on without a pan on them or with an empty pan on them Take care never to lean or reach over a hot electric plate Always point pan handles inward or over the work surface next to the hob to avoid accidentally knocking over a pan as you pass by Take care when frying food in hot oil or fat as the overheated splashes could easily ignite If the control knobs become difficult to turn please contact your local Zanussi Service Centre MAINTENANCE AND CLEANING Before any maintenance or cleaning can be The control knobs may be removed by carefully AN carried out you must DISCONNECT the pulling them upward for easier cleaning hob from the electricity supply The hob is best cleaned whilst it is still warm as spillage can be removed more easily than if it is left to The Hotplates cool Spills onto the actual plate should be removed using warm water and a soft brush nylon or plastic scourer To keep the plates looking as new hotplate The H T conditioner can be purchased from most hardware e Hob 9p stores e g 4 Hob by HomeCare Products follow Regularly wipe over the hob top using a soft cloth the manufacturer s instruction for use well wrung out in warm water to which a little washing up liquid has bee
7. ich is marked with the number 1 4 Connect the black neutral wire to the terminal which is marked with the number 4 5 After fitting a green or yellow green sleeve over the bare copper wire earth wire connect the exposed end to the terminal which is marked with the earth symbol or with the number 5 NOTE The earth wire should be about 2 cm longer than the live and neutral wires Secure the cable by means of the clamp screws and refit the terminal block cover 12 The hob should be conncted to a double pole switch with a minimum gap of 3 mm between the switch contacts and of a type suitable for the required load in compliance with the current electric regulations The switch should be sited within 2m of the hob and be easily accessible upon completion of the installation The switch must not break the yellow and green earth cable at any point Ensure that the hob supply cord does not come into contact with surfaces with temperatures higher than 50 deg C Supply Cable Specifications For Uk use only Connection Min size Cable flex via Cable flex type PVC PVC twin and earth e Cooker 6 mm Control Circuit For Europe use only Min size Cable flex Cable flex type Fuse FO 0488 WIRING DIAGRAM C 145 C 180 145 180 13
8. ives 73 23 EEC 90 683 EEC 93 68 EEC 89 336 EEC current edition DESCRIPTION OF THE HOB Hob Top Rapid Hotplate 2090 W 180 mm dia Normal Hotplate 1040 W 145 mm dia Rapid Hotplate 1570 W 145 mm dia Normal Hotplate 1570 W 180 mm dia Control knob for back left hotplate Control knob for back right hotplate Control knob for front right hotplate Control knob for front left hotplate Electric Hotplates Control Light OOMONDAORWD INSTALLATION WHEN THE HOB IS FIRST INSTALLED AN The hob must be installed according to the Once the hob has been installed it is instructions supplied important to remove any protective materials which were put on in the factory The hob must be installed by qualified personnel to the relevant British Standards Please ensure that once the hob is installed it is easily accessible for the engineer in the event of a breakdown OPERATION ELECTRIC HOTPLATES To switch on a hotplate turn the relevant control knob anticlockwise to the required heat setting The control knob is numbered 1 6 0 OFF 1 Minimum 6 Maximum The hob has two types of hotplates Normal Hotplates We recommend the plates are switched to maximum 6 for a short while to boost the plate and then adjusted to the required setting Rapid Hotplates The rapid hotplates are indicated by a red dot and will heat up more quickly than a normal plate As the red dots are painted on
9. n added Avoid the use of the Alternatively wipe the plates with a drop of olive oil following on a kitchen towel to avoid rust It is important to note that the plate will smoke a little and produce a slightly household detergent and bleaches unpleasant odour when next used 910012186 08060 Pade Unsuitable 10 On steKeaucepans Stainless steel parts the stainless steel spill rings steel wool pads may become straw coloured with use Use a proprietary stainless steel cleaner to remove this bath sink stain removers straw discolouration This also applies to the area Should the hob top become heavily soiled it is around the hotplates on stainless steel hobs recommended that a cleaning product such as Hob Brite or Bar Keepers Friend is used Failure to clean and condition hotplates may lead to rust and corrosion forming on the surface SOMETHING NOT WORKING I the hob is not working correctly please carry out the following checks before contacting your local Zanussi Service Force Centre SYMPTOM SOLUTION 8 The plate does not heat up Check that the unit is plugged in and the electrical supply is switched on Check that the RCCB has not tripped if fitted Check the mains fuse has not blown Check the correct control Knob has been turned 8 The plate is not giving satisfactory results Check the plate is clean and dry Check the cooking pan is the correct size for the plate Check the cooking pan has a flat bo
10. n the hob AN IMPORTANT SAFETY INFORMATION You MUST read these warnings carefully before installing or using the hob II you need assistance contact our Customer Care Department Perishable food plastic items and areosols may be affected by heat and should not be stored above or below the hob unit Service This hob should only be repaired or serviced by an authorised Service Engineer and only genuine approved spare parts should be used Environmental Information After installation please dispose of the packaging with due regard to safety and the environment When disposing of an old appliance make it unusable by cutting off the cable Keep this instruction book for future reference and ensure it is passed on to any new owner CONTENTS For the User Description of the Hob Operation Maintenance and Cleaning Something Not Working Service and Spare Parts Guarantee Conditions Guide to Use the instructions The following symbols will be found in the text to guide you throughout the Instructions AN Safety Instructions Page Page Page Page Page Page 1E Step by step instructions for an operation Hints and Tips For the Installer Technical Data Important Safety Requirements Installation Building In Electrical Connection Wiring Diagram Page Page Page Page Page Page 10 10 12 13 This appliance is manufactured according C to the following EEC direct
11. ob seeping into the cabinet below IEY 1 Place the sealing gasket all around the edge of the cut out 2 Place the hob into the cut out and secure it by means of the relevant fixing clamps and screws as shown in the diagram 3 When the screws have been tightened the excess seal can be removed The edge of the hob forms a double seal which 06100 prevents the ingress of liquids 11 ELECTRICAL CONNECTIONS Any electrical work required to install this hob should be carried out by a qualified electrician or competent person in accordance with the current regulations A THIS HOB MUST BE EARTHED The manufacturer declines any liability should these safety measures not be observed This hob is designed to be connected to a 230 240V 50Hz AC electrical supply Before switching on make sure the electricity supply voltage is the same as that indicated on the hob rating plate The rating plate is located on the bottom of the hob A copy is attached on the back cover of this book The hob is supplied without supply cord A 3 core flexible supply cord must be fitted in accordance with the specification given in the relevant tables iS 1 Remove the mains terminal cover plate from the underside of the hob to expose the mains terminal block 2 Loosen the two cable clamp screws and lift the top section of the clamp enough to allow the cable to be passed through 3 Connect the red live wire to the terminal wh
12. ttom Check the setting is correct for the type of cooking II after all these checks your hob still does not In guarantee customers should ensure that the operate correctly contact your local Zanussi Service above checks have been made as the engineer Force Centre will make a charge if the fault is not a mechanical or electrical breakdown Please note that it will be necessary to provide proof of purchase for any in guarantee service calls SERVICE AND SPARE PARTS SSERVICE FORCE gt II you require spare parts or an engineer contact your local Service Force Centre by telephoning 0870 5 929929 Your call will be routed to your local Service Force Centre For further details please see the accompanying Customer Care Booklet CUSTOMER CARE For general enquiries concerning your Zanussi appliance contact our Customer Care Department by letter or telephone as follows Customer Care Department ZANUSSI 55 77 High Street Slough Berkshire SL1 1DZ Tel 08705 727727 PEACE OF MIND FOR 24 MONTHS Zanussi guarantee conditions We Zanussi undertake that if within 24 months of the date of the purchase this Zanussi appliance or any part thereof is proved to be defective by any reason only of faulty workmanship or materials we will at our option repair or replace the same FREE OF ANY CHARGE for labour materials or carriage on condition that The appliance has been correctly installed and used only on the
13. ur product The guarantee is for the same period and to the same extent for labour and parts as exist in the new country of use for this brand or range of products This guarantee relates to you and cannot be transferred to another user Your new home is within the European Community EC or European Free Trade Area The product is installed and used in accordance with our instructions and is only used domestically i e a normal household The product is installed taking into account regulations in your new country Before you move please contact your nearest Customer Care centre listed below to give them details of your new home They will then ensure that the local Service Organisation is aware of your move and able to look after you and your appliances France Senlis 33 0 3 44 62 29 99 Germany Nurnberg 49 0 911 323 2600 Italy Pordenone 39 0 1678 47053 Sweden Stockholm 46 0 8 738 79 50 UK Slough 44 0 1753 219897 INSTRUCTIONS FOR THE INSTALLER Engineer technical data OVERAII dimensions Width 580 mm Depth 500 mm Height 88 mm Weight 11 Kg cut out dimensions Width 550 mm Depth 470 mm Thickness 30mm SUPPLY CONNECTIONS Electric 230 240V 50Hz AC electric supply This appliance complies with the EEC Directive No 89 336 concerning suppression of radio electrical interference Heating elements Ratings Normal back right Hotplate 180 mm 1570 W Normal back left Hotplate 1
Download Pdf Manuals
Related Search