Yamaha MOTIF XF 1.1 User's Manual
Contents
1. New Functions in MOTIF XF Version 1 10 Yamaha has upgraded the MOTIF XF firmware to Version 1 10 adding a number of new functions This supplement to the Owner s Manual describes these changes Editing and storing a Sample Voice as a Mixing Voice You can now convert a Sample Voice to a Mixing Voice in the Mixing Play display of the Song Pattern mode allowing you to then edit the sampled audio as a Voice 1 From the Mixing Play display select a Part to which a Sample Voice is assigned VceConv appears at the tab corresponding to F6 Initial ized Voir Part g9 40 11 1 13 14 15 16 Po Pn Pn Pn Pn Pn Pn Ph Pn Pn PH PN Pn Pn Fn Ph Pn Bank PRi PR PRi PRi PRI PRi PRI PRI PRI PR PRi PRi PRI PRI PRI Humber 001 O01 O07 O01 O01 O01 O01 O01 O01 ooi ooi ooi oof OOF om rev sed IPEMB e fie lil edie Cho Send 19 a 0 0 a 010 o1a 0 a 0 0 01010 Category ee eeielelauicllul sFR Sw 100 100 100 100 100 100 100 100 100 100 100 100 100 100 Effect Lee ton 2 Press F6 VceConv to convert a Sample Voice of the selected Part to a Mixing Voice Completion of conversion calls up the Mixing Voice Store window 3 Use the data dial or INC YES DEC NO to select a Store destination number in the Mixing Voice Store window NOTE Only the MIXV Mixing Voice Bank is available 4 Press ENTER to call up the Confirmation dialog To cancel the Store operation press DEC NO to return to the origi2. aveforms If you select None at FL1 and FL2 the Load operation will load the file but not the Waveforms to the Flash Memory Expansion Module 141 2HB 495 dH Device Dir usb 1 O Trashes O MOTIF sF Category Search for Arpeggio Types With this new version you can use the Category Search function to conveniently find desired Arpeggio Types 1 cal up the Category Search window for the Arpeggio Type Press CATEGORY SEARCH to call up the Category Search window for the Arpeggio Type from any of the following displays e F4 Arpeggio display of the Voice Play mode or Performance Play mode e F2 ARP Main or F3 ARP Other display of the Voice Common Edit Performance Part Edit or Mixing Part Edit mode 2 Find the desired Arpeggio Type on the Arpeggio Category Search window Select the Main Category at then select the Sub Category at to call up the listed Arpeggio types at Arpeggio List Move the cursor to the desired Arpeggio Type then press ENTER to finalize your selection Arpessio List Call 1i p E 4 5 5 q H E E Se Hain Sub List Favoriter Sett Clear Clear all Favorite window F1 Main Pressing this will move the cursor to Main column F2 Sub Pressing this will move the cursor to Sub column New Functions in MOTIF XF Version 1 10 3 F3 List Pressing this will move the cursor to Arpeggio List F4 Favorite Pressing this will ca
3. dit mode press CATEGORY SEARCH to call up the Category Search window for the Waveforms Find the desired Waveform on the Category Search window Select the Main Category at then select the Sub Category at to call up the listed Waveform types at Waveform List Move the cursor to your desired Waveform then press ENTER to finalize your selection 4 New Functions in MOTIF XF Version 1 10 Waveform List All i p E 4 5 E q H Favorite window F1 Main Pressing this will move the cursor to Main column F2 Sub Pressing this will move the cursor to Sub column F3 List Pressing this will move the cursor to Waveform List F4 Favorite Pressing this will call up the Favorite window F5 Set Clear Pressing this will register the current Waveform to the Favorite Category or remove the current Waveform from the Favorite Category With the checkboxes listed at left you can confirm whether or not each Waveform Is registered F6 All Clear By pressing this then INC YES you can remove all the registered Waveforms from the Favorite Category SF6 All Filtered Pressing this will toggle the indication between All and Filtered Pressing SF6 All will show all the Waveforms of the current Category on the Waveform List Pressing SF6 Filtered will show only representative Waveforms picked up from all Waveforms on the Waveform List Favorite window Indicates
4. e Sram Hormalize ice Increasing the available memory of the Flash Memory Expansion Module A new Sampling Job now lets you increase the available memory of the Flash Memory Expansion Module 1 From the F3 Other display of the Sampling Job select 05 Delete Same Name Waveforms then press ENTER 2 New Functions in MOTIF XF Version 1 10 Sample Job Select fam am kI E hi Rao i Copy to Flash Wemory Copy from Flash hemor Delete Same Hame Waveforms 1 it i Gl un 2 Select the target memory USR FL1 or FL2 at then select the Waveform number at All the Waveforms having the same name are listed on the Same Name Waveforms section of the display ti a ee ee Recordable Time Dhesbenk Wavetorm Other NOTICE This Job will delete all Waveforms with the same name except for the selected Waveform even if they contain different data 3 Press ENTER to execute the Job This operation will delete all the Waveforms with the same name except for the selected Waveform NOTE This operation will cancel the link status between the Voices and deleted Waveforms then make a new link between the same Voices and the undeleted Waveforms respectively Revision of Key Bank number assignment after Sampling The method of the Key Bank number assignment has been changed from the previous version In the previous version 1 was assigned to
5. ll up the Favorite window F5 Set Clear Pressing this will register the current Aroeggio Type to the Favorite Category or remove the current Arpeggio Type from the Favorite Category With the checkboxes listed at left you can confirm whether or not each Arpeggio Type Is registered F6 All Clear By pressing this then INC YES you can remove all the registered Arpeggio Types from the Favorite Category SF1 ARP1 SF5 ARP5 Pressing each of these will change the Arpeggio Type from the current one SF6 All Filtered Pressing this will toggle the indication between All and Filtered Pressing SF6 All will show all the Arpeggio types of the current Category on the Arpeggio List Pressing SF6 Filtered will show only representative Types picked up from all Types on the Arpeggio List Favorite window Indicates the Aroeggio Types registered to the Favorite Category Pressing F4 Category will return to the Aroeggio Category Search display Main Sub Favorite List Oraan lt Porkk gt GtFI j GtHG Bass Bali Stra naa mw fw Category Set Clear Clear All Category Search for the Waveforms With this new version you can use the Category Search to find desired Waveforms in the Normal Voice Element Edit mode and Drum Key Edit mode 1 Call up the Category Search window for the Waveforms From the F1 Oscillator display of the Normal Voice Element Edit mode or Drum Voice Key E
6. nal display 5 Press INC YES to execute the Store operation After the Store has been completed a Completed message appears and operation returns to the Mixing Voice Play display You can confirm that the stored Mixing Voice is assigned to the Part selected in step 1 NOTICE After the above operations make sure to execute the Song Pattern Store Otherwise the Mixing Voice assignment will be lost when turning the power off or selecting the different Song Pattern Editing a Waveform on the optional Flash Memory Expansion Module You can edit a Waveform on the optional Flash Memory Expansion Module by using the newly added Sampling Job 1 From the F3 Other display of the Sampling Job select 04 Copy from Flash Memory then press ENTER 2 Copy a Waveform from the Module to the Sampling memory At select the source memory FL1 or FL2 At select a Waveform At select whether or not the original wave is to be deleted After these operations press ENTER Waveform Hew Waveform 1 3 Delete original Sample Memory Recordable Time IHFO Eesbank Waveform Other NOTE This operation will cancel the link between all the Voices and the original Waveform then make a new link between the same Voices and the Waveform copied to the Sampling memory 3 Edit the Waveform in the sampling memory by using the Sampling Edit and Sampling Job operations 4 From the F3 Othe
7. r display of the Sampling Job select 03 Copy to Flash Memory then press ENTER 5 Copy the edited Waveform from the sampling memory to the Flash Memory Expansion Module At confirm that the edited Waveform number is shown At select whether or not the original wave on the Sampling Memory is to be deleted At select the destination memory FL1 or FL2 After these operations press ENTER EN New Functions in MOTIF XF Version 1 10 1 Sample Jobj 63 Corpy to Flash Memory Waveform Hew Waveform 1 Delete original Flash Wemory FL1 Recordable Time IMFO Eesbank Wavetorm Other NOTE This operation will cancel the link between all the Voices and the edited Waveform on the Sampling Memory then make a new link between the same Voices and the Waveform copied to the Flash Memory Expansion Module Additional menus in Sampling Edit Sampling Main display With this new version F3 Normalize F4 Slice and F5 Remix have been added to the Sampling Edit display and Sampling Main display respectively allowing you to more easily call up these displays Sorrge Wayetorm Hew Waveform 1 Track El Key Eo Velocity i Bee Measure Bk Keybank Select Ho Sample Property Sample Size ddi SKB Frequency dd ikH Recordable Time Hono Steren steren Rect Sorrge Waveform Bail Hew Waveform 1 Track A E AE Eo Velocity 1 eee Heasure BE 1 1 Settina Ratio Recordable Tim
8. the Key Bank of the latest Sampling and the rest of the Key Bank numbers were increased by 1 In this new version the next number is assigned to the Key Bank of the latest Sampling Select Waveform Bhg Hew Waveform 1 Track DH 3 Velocity D RER Weasure Velocity Hel 127 Si Sy eee 127 Sample Property Sample Size 2 dhe Frequency dd 1FHz Recordable Time Mono Stereo steren Hormalize Slice Remix Pec Loading WAV AIFF files and assigning each of them to the keys With this new version you can load WAV or AIFF files in a single folder at the same time The loaded files will be assigned to the keys in alohabetical order from the specified key This allows you to easily create your own custom Waveforms 1 Connect the USB storage device containing the desired WAV AIFF files in a single folder to the USB TO DEVICE terminal 2 Enter the mode according to the destination to which the Waveform is to be assigned When you want to assign the files to a User Voice Enter the Voice mode then select a Drum or Normal Voice Or alternately enter the Performance mode then select the Performance having an empty User Voice When you want to assign the files to a Sample Voice Enter the Song mode or Pattern mode 3 Press FILE then F1 File 4 Make the settings for the Load operation At select WAV or AIFF At select the desired folder directory then any of the files At select the head Key
9. the Waveforms registered to the Favorite Category Pressing F4 Category will return to the Waveform Search display Favorite List i p E 4 5 E q E Category Set Clear Clear All U R G Digital Musical Instruments Division 2010 Yamaha Corporation WW47430 Cerne
10. to which the first WAV AIFF file is assigned At select the destination memory of the Load operation When entering the Voice mode in step 2 select an Element to which the Waveform is to be assigned When entering other modes in step 2 select a Part to which the empty User Voice is assigned 161 2HB 495 4B 1 Type Bank FRE 1 el Element Ze 3 Full Concert Grand Load 4 Lave Load Rename Delete _ L_New bir _ File Mount Forma 5 Press F6 Load multi to execute the Load operation 6 Confirm the result of the Load operation When entering the Voice mode or Performance mode in step 2 Exit from the File mode then play the corresponding Voice or Performance to check the sound NOTICE After the above operations make sure to execute the Voice Store operation Otherwise the Voice will be lost when turning the power off or selecting a different Voice When entering the Song mode or Pattern mode in step 2 Exit from the File mode select the corresponding Part of the song or Pattern then play the keyboard to check the sound NOTICE After the above operations make sure to execute the Song Pattern Store operation Otherwise the Sampling Voice assignment will be lost when turning the power off or selecting a different Song Pattern Additional option in file loading operation With this new version you can load the file without the Waveforms even if the corresponding file contains W
Download Pdf Manuals
Related Search