Home

Yamaha DVD-S2500 Owner's Manual

1. Other components as they may cause damage and or discoloration on the surface of this unit Burning objects 1 e candles as they may cause fire damage to this unit and or personal injury Containers with liquid in them as they may fall spilling the liquid and causing an electrical shock to the user and or damage to this unit Do not cover this unit with a newspaper tablecloth curtain etc in order not to obstruct heat radiation If the temperature inside this unit rises it may cause fire damage to this unit and or personal injury Do not plug in this unit to a wall outlet until all connections are complete Do not operate this unit upside down It may overheat possibly causing damage Do not use excessive force on switches knobs and or cords When disconnecting the power cord from the wall outlet grasp the plug do not pull the cord Do not clean this unit with chemical solvents this might damage the finish Use a clean dry cloth Use only the voltage specified on this unit Using this unit with a higher voltage than specified is dangerous and may cause fire damage to this unit and or personal injury YAMAHA will not be held responsible for any damage resulting from use of this unit with a voltage other than as specified To prevent damage by lightning disconnect the power cord from the wall outlet during an electrical storm Do not attempt to modify or fix this unit Contact qualified
2. VARO AVATTAESSA OLET ALTTIINA NAKYVALLE JA NAKYMATT OMALLE LASER SATEILYLLE ALA KATSO SATEESEEN VORSICHT SICHTBARE UND UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GE FFNET NICHT DEM STRAHL AUSSETSEN DANGER VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AVOID DIRECT EXPOSURE TO BEAM ATTENTION RAYONNEMENT LASER VISIBLE ET INVISIBLE EN CAS D OUVERTURE EXPOSITION DANGEREUSE AU FAISCEAU m 11 12 13 14 15 16 CAUTION READ THIS BEFORE OPERATING YOUR UNIT To assure the finest performance please read this manual carefully Keep it in a safe place for future reference Install this sound system in a well ventilated cool dry clean place away from direct sunlight heat sources vibration dust moisture or cold In a cabinet allow about 2 5cm 1 inch of free space all around this unit for adequate ventilation Locate this unit away from other electrical appliances motors or transformers to avoid humming sounds Do not expose this unit to sudden temperature changes from cold to hot nor locate this unit in an environment with high humidity Oe a room with a humidifier to prevent condensation inside this unit which may cause an electrical shock fire damage to this unit and or personal injury Avoid installing this unit in a location where foreign objects may fall onto this unit or where this unit may be exposed to liquid dripping or splashing On the top of this unit do not place
3. Default Audio see page 17 Youcan select the audio language spoken in video discs Available choices are determined by the disc Go to Default Audio Setup gt Language gt Default Audio by using A V lt ID gt buttons on the remote control then press gt Choices are displayed on the right column Select a language by using A V buttons Press lt J to return to the previous menu 3 Default Subtitle see page 17 You can select the subtitle language set as default Available choices are determined by the disc Go to Default subtitle Setup gt Language gt Default subtitle by using A V lt ID gt buttons on the remote control then press gt Choices are displayed on the right column Select a default subtitle language by using A V buttons Press lt J to return to the previous menu TV shape see page 15 2 3 You can select the aspect ratio of the video displayed on the TV monitor Select Widescreen if you connect to a wide screen monitor If you connect to a conventional monitor select 4 3 panscan the left and right sides are trimmed when you play 16 9 video or 4 3 letterbox black areas appear at the top and bottom when you play 16 9 video Go to TV shape Setup gt TV gt TV shape by using A V lt D buttons on the remote control then press gt gt Choices are displayed on the right column Make a choice by using A V buttons Press lt J to return to the previous men
4. Picture Mode Adjusts the color tone to suit your preference and the Widescreen Through 4 3 PillaBox 3 Squeeze Initial setting Natural 10801 Dot by Dot The resolution i ically selected h th eee e resolution is automatically selected to match the i Auto monitor you are using Set TV shape 4 3 Aspect Adjusts the overall brightness of the picture This and your monitor setting to match the selected function is not available for signals output from resolution COMPONENT video jacks and HDMI video signals Choices 7 to 7 Depending on the monitor you are using the monitor Initial setting 0 setting names may differ from those shown above Sharpness 1 If the monitor you are using has an aspect ratio of 4 3 and is only capable of either 480p or 576p resolution select 4 3 panscan or 4 3 letterbox 2 Depending on the monitor you are using this setting may appear as Squeeze or Full 3 If the aspect ratio you desire is not available select Sound the most suitable setting from Auto 4 3 PillarBox and NL_ Stretch Adjusts the sharpness of the video Choices 0 to 7 Initial setting 0 Karaoke vocal Enables you to play multi channel karaoke DVDs The Notes karaoke channels on the disc will be mixed into normal While HDMI video signals are being output stereo when you choose On component video is muted Choices On Off For settings other than Auto HDMI v
5. Ee 24 WPS deI ME 24 PIayinp a E 24 Choosing an Album Track to playback 24 IPSE EE 24 TEE E 23 JPEG dise TOBl CS oe ooo tiet i boc ep DX SEE Der de toques 25 Payne EE 25 SHAS SNOW setne ooh bete Erde edite laane teva as 25 KOLAS the e 25 General e a castis iro Pra tie lil jaki id mtted 26 Moving to another segment neneeeeeesesessesssssssssssesese 26 DAL EE 26 DIOWTHOLGODS S ouod ege 26 Still picture and frame by frame playback 26 EE le 26 IRGC Ges PEUT 27 IRGC Ab EE 21 E ates sau tes esha ana E 21 e ei malai naa aasal haa tada 27 LOOV GA rea mes 21 FTS video audio program 28 Activating deactivating the FTS program 28 Erasing a track chapter index from the FTS bet 28 Erasing all tracks chapters indexes from the FTS list 28 DISCJOCK aa tid bocca I eet DE 28 Activating deactivating Disc Tock eeeeseesseessesssesesssess 28 AURON ia C565 eege 28 RE a E 29 Parental CODEOL eeneg 29 Activating deactivating Parental Control 29 COWIE AA Eeer 29 Changing the four digit DIN 29 If you forget your four digit code 29 Troubleshooting 30 Specifications 31 Introduction Thank you for purchasing the YAMAHA DVD AUDIO VIDEO SA CD player This Owner s Manual explains its basic operations Patent information DO Manufactured under license from DIGITAL Dolby Laboratories Do
6. A B repeats a specific segment SHUFFLE plays tracks chapter in random order SCAN plays the first 10 seconds of each track chapter within a disc Press and hold button for about two seconds Preparation There are various ways to connect the player depending on the equipment you wish to use The following drawings illustrate some possible configurations Please refer to manuals for other equipment as necessary to ensure that you make the correct connections Do not connect the player via your VCR The video quality could be distorted by the copy protection system Do not connect the player s audio output jack to the phono input jack on your audio system Audio connection Digital audio connections This unit features COAXIAL and OPTICAL digital output jacks Connect one or both of them to digital input jacks of an AV receiver You can also enjoy high quality stereo sound at sampling frequencies of 88 2 and 96 kHz assuming the material is not copy protected and the equipment you connect is compatible with these signals AV Insert fully with this side AV receiver facing up Notes If the audio format of the digital output does not match the capabilities of your receiver the receiver will produce a strong distorted sound or no sound at all Make sure to select the appropriate audio format on the disc menu screen Pressing AUDIO once or more ma
7. YAMAHA DVD AUDIO VIDEO SA CD PLAYER LECTEUR DE DVD AUDIO VIDEO SA CD DVD S2500 OWNER S MANUAL MODE D EMPLOI BEDIENUNGSANLEITUNG BRUKSANVISNING MANUALE DI ISTRUZIONI MANUAL DE INSTRUCCIONES GEBRUIKSAANWIJZING A GB YAMAHA NATURAL SOUND DVD AUDIO VIDEO SA CD PLAYER DVD S2500 COMPACT DVD SE AUDIO VIDEO SUPERAUDIOCD DIGITAL VIDEO Important Note DK Advarsel Laserrudstraling ved abning nar sikkerhesafbrydere er ude af funktion Undg u tsettelse for str ling Bem rk Netafbryderen STANDBY ON er sekund rt indkoblet og afbryder ikke str mmen fra nette Den indbyggede netdel er derfor tilsluttet til lysnettet sa l nge netstikket sidder i stikkontakten N Observer Nettbryteren STANDBY ON er sekundert innkoplet Den innebygdenetdelen er derfor ikke frakoplet nettet sa lenge apparatet er tilsluttet nettkontakten S Klass 1 laserapparat Varning Om apparaten anv nds pa annat s tt n i denna bruksanvisning specificerats kann anv ndaren uts ttas f r laserstralning som versjruder gr nsen f r l serklass 1 Observera Str mbrytaren STANDBY ON r sekund rt kopplad och inte bryter str mmen fr an n tet Den inbyggda n tdelen r d rf r ansluten till eln tet sa lange stickproppen sitter i v gguttaget SF Luokan 1 laserlaite Klass 1 laserapparat Varoitus Laitteen k ytt minen muulla kuin t ss k ytt ohjeessa mainitulla tavalla saattaa altistaa
8. You can specify a country code in the On screen menu Setup gt Language gt Country See Country on page 29 Choices 0 to 8 Initial setting 0 Country Selects a country to apply its rating system to Parental Level control Features PBC A VCD menu screen is displayed when this setting is on Choices On Off Initial setting On Sleeptimer Places this unit in standby mode when playback is stopped and this unit is not operate for 20 minutes Choices On Off Initial setting Off On screen menu TV TV shape If you connect to a conventional 4 3 aspect TV select 4 3 panscan the left and right sides are trimmed when you play 16 9 video or 4 3 letterbox black areas appear at the top and bottom when you play 16 9 video Select Widescreen if you connect to a Wide Screen TV Choices 4 3 panscan 4 3 letterbox Widescreen Initial setting 4 3 panscan 4 3 panscan 4 3 letterbox Widescreen us TV System NTSC PAL conversion Allows you to select PAL NTSC or Auto mode to match your TV system You can play PAL discs on NTSC monitor and NTSC discs on PAL monitor The initial setting is NTSC U S A model PAL U K Europe and Australia models Choices PAL NTSC Auto The following conversions are supported Output format Disc Selected mode Format A NTSC PAL AUTO NTSC NTSC PAL NTSC PAL NTSC PAL PAL Notes In
9. by using the A V lt 1 buttons then press the D gt button Press the A V to select On or Off Press the 1 button then press ON SCREEN to exit from the On screen menu Erasing a track chapter index from the FTS list You can erase the items that you programmed in the FTS list Press ON SCREEN on the remote control The On screen menu appears Go to Playlist Toolbar 3 Program gt Playlist by using the A V lt 1 gt buttons then press the D gt button Press the A V button to select the item you want to erase then press ENTER OK gt The selected item disappears from the list Press the I button then press ON SCREEN to exit from the On screen menu 28 N 0 01 RO Erasingall tracks chapters indexes from the FTS list You can erase everything at once in the FTS list Press ON SCREEN on the remote control The On screen menu appears Go to Clear all Toolbar 3 Program gt Clear all by using the AV lt ID gt buttons then press the D gt button gt Cleared appears momentarily then all items in the list are erased Press the lt J button then press ON SCREEN to exit from the On screen menu Disc lock 2 a vo Activating deactivating Disc lock Using this function you can prohibit the access of others to certain discs Press ON SCREEN on the remote control The On screen menu appears Go to Enter PIN Setup gt Access gt Enter PIN using the A V lt ID gt b
10. 0 Front L Vol Choices 6 to 6 Initial setting 0 Centre Vol Choices 6 to 6 Initial setting O Surround R Vol Choices 6 to 6 Initial setting 0 Surround L Vol Choices 6 to 6 Initial setting 0 Subwoofer Vol Choices 6 to 6 Initial setting 0 SA CD Mode You can adjust the volume level output from each channel for SA CD playback You must choose Multi channel for Analog output to make this function available See Analog output on page 16 If you adjust the volume level for any speaker the volume level for the other speakers is adjusted accordingly Cut off frequency Cut off frequency adjustment for a subwoofer Choices 60 80 100 120 Hz Initial setting 120 Hz 18 Slope Filter slope adjustment for a subwoofer Choices 12 18 24 dB oct Initial setting 12 dB oct Front R Vol Choices 6 to 6 Initial setting 0 Front L Vol Choices 6 to 6 Initial setting 0 Centre Vol Choices 6 to 6 Initial setting 0 Surround R Vol Choices 6 to 6 Initial setting 0 Surround L Vol Choices 6 to 6 Initial setting 0 Subwoofer Vol Choices 6 to 6 Initial setting 0 LLINK You only need to make this setting if you connected this player to an 1 LINK compatible component Connected components must be DTCP Digital Transmission Content Protection compliant in order to play DVD audio and Super Audio CD signals receiv
11. and playback Smart Resume starts This unit memorizes the last five discs and their next starting points where they are stopped at the last time operation Using this function you can quickly return to the scene you were watching last time gt If you press PLAY when the tray is open this unit closes the tray and starts playback To interrupt playback Press STOP to interrupt playback Resuming playback of the disc that has not been ejected from this unit e Press PLAY gt Playback resumes automatically from the point where the playback was interrupted e Press STOP again then press RETURN RESUME on Aus the remote control gt Playback resumes from the point where the playback was interrupted e Press STOP again then press PLAY gt Playback starts from the beginning of the disc e Press PLAY when the resume icon is on screen gt Playback resumes from the point where the playback DVD Video and DVD Audio was interrupted e DVD Video discs may contain one or more titles and Resuming playback of the disc that has been ejected each TITLE may contain one or more chapters fronihis mit DVD Audio discs may contain one or more groups and e pelab de each group may contain one or more tracks If Disc Lock is set to On and the disc inserted is not authorized you must enter a four digit code see Access on page 15 Playback starts from the beginning of the disc Disc Structure e Press PLAY when the r
12. in the On screen menu Toolbar gt Search gt Time gt Playback pauses gt The elapsed playing time is displayed in a time edit window 2 Enter hours minutes and seconds from left to right in the time edit window using the remote control numerical buttons Each time an item is entered the next item is highlighted 3 Press the ENTER OK button to confirm the selected time Playback starts from the selected time position on the disc 4 Press ON SCREEN to remove the menu bar Repeat Press REPEAT button to repeat a certain segment of the disc Each time you press REPEAT the repeat mode changes as follows DVD A Track DVD V Chapter Group Title Disc Disc Off Off Track SA CD gt Y yCD 3 i Area Ge Disc v Y Off Off Track Y Album Y Disc MP32 Off This feature may not be available on some discs Repeat A B DVDAD SACDO ACD 2 cb MIZ Repeat a sequence in a track enw Repeat a sequence in a title Press A B at the desired starting point gt REPEAT A is displayed on the front panel display Press A B again at the desired end point gt REPEAT A B appears briefly on the front panel display and the repeat sequence begins To exit the sequence press A B gt REPEAT OFF is displayed on the front panel display as Operation Shuffle ao CD MD This function shuffles the playing order of chapters or tracks within a title group album if the title group alb
13. the track list on the TV screen or by pressing the numerical buttons or A V buttons Disc structure 4 CD TRACK 1 E TRACK 2 TRACK 3 Playing a disc Insert the disc and close the tray gt Playback starts automatically gt The TV screen will display the track list and current playing status Playback will stop at the end of the disc To stop playback press STOP Video CD and Super Video CD Current VCD 2 0 and Super Video CD 1 0 standard features include Video CDs may contain one or more tracks and tracks may contain one or more indexes You can display either tracks or indexes Disc structure CD TRACK 1 INDEX 1 INDEX 2 INDEX 3 TRACK 2 1 INDEX 1 INDEX 2 INDEX 3 Operation The following VCD and SVCD features and formats are supported Features Video CDs 2 0 Super Video CDs 1 0 Video MPEG 1 m A variable up to 2 6 Mbps bit rate constant 1 150 Kbps 480x480 interlaced resolution NTSC 352x240 29 97Hz 29 97Hz resolution PAL 352x288 25Hz 480576 inierinced 25H Still picture photo MPEG 1 MPEG 2 1 Frame resolution NTSC 352x240 704x480 480x480 704x480 resolution PAL 352x288 704x576 480x576 704x576 Audio c NH MPEG 1 layer II 44 1 KHz sampling 224Kbps 44 KHz bit rate p 32 384Kbps N 1 stereo 2 mono audio channels Stereo with Dolby Pro lt 2 stereo 4 mono surround sound y MPEG 1 5 1 extension Logic Overlay graphics text overlay video plane sub channels lt
14. then press gt Make a choice with lt Choices 180 90 0 90 180 To return to the previous menu press lt To exit from the On screen menu press ON SCREEN Note This function is not available during slide show playback 25 Operation General features Moving to another segment DVDAD DVD SAD WCDD CD MP3 When a disc includes more than one segment you can quickly move to another segment by the following operation Moving to the appointed segment directly 1 Press TITLE CHAP button on the remote control The TITLE CHAP menu appears on the screen 2 Press A V or the numerical buttons to select a segment Press RETURN RESUME button on the remote control to erase the TITLE CHAP menu from the screen Moving to the next previous segment Press gt P or KIKI briefly during playback to proceed to the next segment or to return to the beginning of the current segment Press KIKI twice quickly to step back to the previous segment Numeric button operation For the direct access to a segment enter the segment number using the numerical buttons 0 9 on the remote control For example to select the segment number 12 press 1 first then press 2 Search DD DVD SAD CD 2 DD MP3 Key control To search forward or reverse at various speeds hold down P or KIKI for more than two seconds The choices are for audio discs 8 4 4 8 and for video discs 32 4 4 32 OSD co
15. to select x1 Then press the ZOOM button in order to turn off the cursor from the screen 27 Operation I FTS video audio program The FTS Favorite Track Selection function enables you to store your favorite tracks etc The FTS list can contain up to 20 items The most recent program list is placed on the top of the existing list Press ON SCREEN on the remote control The On screen menu appears Go to Tracks Toolbar gt Program gt Tracks by using the A V lt I gt buttons then press the D gt button Press the A V button to select the item to store in your FTS list then press the ENTER OK The selected item flashes momentarily when it is stored in the FTS list Repeat the above procedure to set the FTS list Press the 1 button then press ON SCREEN to exit from the On screen menu gt This unit starts playing the FTS list automatically Notes You can check your FTS list in the On screen menu Toolbar gt Program gt Playlist Press the N V buttons to navigate the playlist menu For SA CD you can program FTS list in the currently selected area only For DVD Audio the password must have been entered in order to play bonus tracks Activating deactivating the FTS program You need to select On in the Program menu to activate the FTS function Press ON SCREEN on the remote control The On screen menu appears Go to Program Toolbar gt Program gt Program
16. video output Select INL Stretch for display of 4 3 image on the 16 9 screen with non linear stretching Center position of screen 1s stretch less than the side Select 4 3 PillarBox to display 4 3 image on the 16 9 screen without stretching No aspect ratio adjustment is made when Auto is selected We recommend setting the aspect ratio on your TV if the function is available Choices 4 3 PillarBox NL Stretch Auto Initial setting Auto TrueLife Produces more dynamic picture by increasing the picture contrast and the color intensity This function is available for progressive scan output only Choices 0 to 7 Initial setting 0 DCDi DCDi Directional Correction Deinterlacing computes and tracks the angle of the screen edge to fill in the missing pixel on the TV screen DCDi will optimize the image quality significantly especially during the slow motion playback This function is available for progressive scan output only Choices On Off Initial setting On Chroma Delay The chroma color and luminance brightness signals are not synchronized The Chroma Delay setting allows you to adjust the advance delay of the chroma signal to yield a perfectly clear picture This function is available for signals output from COMPONENT video jacks only Choices 3 to 3 Initial setting 0 Gamma Enables you to adjust the intensity of the picture non linearly A positive value enables you to bring out low level det
17. will be replaced when a new disc is added Double sided DVDs and multi volume VCDs may have a different ID for each side In order to make Disc Locks to such discs each side must be authorized Deauthorizing discs If you authorize a disc for Play always the disc content will always be available for playback until you deauthorize the disc Follow the procedure below to deauthorize a disc Insert the disc gt Playback starts automatically Press STOP within about 10 seconds after appears in the screen gt Q will appear on the screen indicating that the disc is now locked Parental Control 2 2 DVD movies may contain scenes that are unsuitable for children Therefore discs may contain Parental Control information that may apply to the entire disc or to certain scenes These scenes are rated from 1 through 8 Alternative more suitable scenes may be available on the disc Ratings are country specific The Parental Control feature enables you to prevent discs from being played by your children or in some cases to substitute alternative scenes Activating deactivating Parental Control When the disc playback is stopped press ON SCREEN on the remote control The On screen menu appears Go to Enter PIN Setup gt Access gt Enter PIN by using the A V lt 1 buttons then press the D gt button Enter your four digit PIN Press the A V button to select Parental level then press the
18. you play the discs that allow down mixing of the multi channel audio sources A OPEN CLOSE opens or closes the disc tray Functional Overview Rear panel HDMI output terminal connect to the HDMI jack on a HDMI compatible AV component SCAN MODE switch switches the component video output signals between progressive and AC IN Main inlet interlace connect to a standard AC outlet COMPONENT video jacks i LINK connectors connect to an AV receiver with Y PB connect to the i LINK jack on an PR inputs 1 LINK compatible component MODEL NO DVD S2500 120 VOLTS 33WATTS 60Hz YAMAHA CORPORATION 000000 0000 OAI COAXIAL digital audio output OPTICAL digital audio output jack connect to the audio input jack on connect to the audio input jack on digital digital coaxial audio equipment optical audio equipment AV terminal MIXED 2CH audio output jacks connect to a SCART cable connect to audio inputs on your AV receiver or stereo system S VIDEO output 6CH DISCRETE audio output jacks connect to an AV receiver with 6 ch discrete connect to an S Video input jack on an audio input jacks your AV receiver VIDEO output composite video out connect to the video input jack on your AV receiver Caution Do not touch the inner pins of the jacks on the rear panel Electrostatic discharge may cause permanent damage to the unit Functional Overview
19. 4 coding 4 color CLUT 2bits pixel The following formats are not supported for VCDs HQ VCD encoded at 2 4Mbps or 2 6Mbps XVCD eXtended VCD with higher resolution and data rate DIVX format files Playing a disc Insert the disc and close the tray gt Playback starts automatically gt The current track number and its elapsed playing time are displayed in the status window Playback will stop at the end of the disc To stop playback press STOP Notes The Disc Resume feature is also available for VCDs and SVCDs see the Smart Resume section on page 20 When you play a Karaoke disc you can change the vocal by pressing AUDIO on the remote control Playback Control PBC Playback Control is a feature on some Video CDs and Super Video CDs that enables users to access selected tracks directly from the disc menu Insert a Video CD or Super Video CD that features PBC then press PLAY Navigate the menu using the buttons indicated on the TV screen until your chosen passage starts to play If a PBC menu displays a list of tracks you can select a track directly Enter your choice using the numerical buttons 0 9 Press RETURN RESUME or KIKI to return to the previous menu Press EE to proceed to the next menu You may also select PBC OFF in the On screen menu gt When PBC OFF is selected PBC menus are unavailable 23 Operation MP3 You can play MP3 music that wa
20. Do not wipe in a circular motion e Do not use solvents such as benzene thinner commercial cleaners or anti static spray designed for analog records Functional Overview Front panel STANDBY ON turns on this unit or sets it to the standby mode Disc tray KKI moves to the previous chapter or track DDi moves to the next chapter or track YAMAHA varura souno ovo auvo vioeo sa CD PLAYER DVD s2500 CJ STOP stops playback Il PAUSE pauses playback PLAY starts playback WN MIX GC hupio viDEo DVD AUDIO indicator lights up when the unit detects DVD Audio signals SA CD indicator lights up when the unit detects SA CD signals MULTI CH indicator lights up when you play multi channel audio source HDMI indicator lights up when the unit is capable of outputting signals from the HDMI High Definition Multimedia Interface terminal i LINK indicator lights up when an AV receiver selects 1 LINK IEEE1394 DO _ LLLA ALL Heel DD el vr Front panel display shows information about the operational status of the unit PROGRESSIVE indicator lights up when the unit enters PROGRESSIVE mode AUDIO DIRECT indicator lights up when you enter the AUDIO DIRECT mode by pressing the AUDIO DIRECT button on the remote control during audio disc playback DOWN MIX indicator lights up when
21. In this setting the multi channel audio is down mixed to a stereo signal Select this setting when connecting to a TV stereo amplifier receiver etc Dolby Surr Compat Select this setting when using equipment with a Dolby Surround Pro Logic decoder In this setting the multi channel audio Dolby Digital MPEG 2 DTS is downmixed to a Dolby Surround compatible 2 ch output SA CD and PCM signals with a sampling frequency of over 88 2 kHz are downmixed to normal stereo 3D sound In a setup without rear speakers analogue stereo output 3D Sound remixes the six channels of digital surround except for SA CD and PCM signals with a sampling frequency of over 88 2 kHz into a two speaker output while retaining all of the original audio information The result is the sensation of being surrounded by multiple speakers Multi channel Select this setting when using a multi channel AV receiver with 6 ch discrete inputs The multi channel audio signals those of like DVD Audio DVD Video and SA CD are output from the respective 6 ch discrete output jacks In this mode this unit will perform DTS decoding Dolby Digital 5 1 channel decoding or MPEG Multichannel decoding when applicable and Dolby Pro Logic II decoding on 2 ch sound tracks except for SA CD and PCM signals with a sampling frequency of over 88 2 kHz 16 PCM output Enables you to select PCM digital output at 48 kHz or 96 kHz If you select 48 KHz PCM data will be conver
22. Remote control DIMMER adjusts the display brightness AUDIO DIRECT switches video output on and off during audio disc playback SOUND MODE selects the required sound mode for SA CD CD Stereo or Multi channel if available for DVD VCD Stereo Dolby Surround compatible 3D sound or o turns the power of this unit ON or enters standby mode 0 9 numeric buttons SUBTITLE Multi channel selects subtitle languages AUDIO PAGE E selects audio languages and formats turns pages of the DVD Audio still pictures ANGLE selects DVD camera angles TITLE CHAP selects title or chapter ZOOM enlarges video images STATUS displays current playback information on the front panel display and on the status window on screen RETURN RESUME displays the previous menu or resumes playback ON SCREEN accesses or removes the player s On screen menu AV ls left right up down selects an item in the menu STOP LJ ENTER OK stops playback acknowledges menu selection PLAY gt starts playback khk YAMAHA accesses the menu of a DVD disc PAUSE 00 pauses playback temporarily KKI frame by frame playback searches backward accesses a previous chapter or track MUTE D disables or enables sound output searches forward accesses the next chapter or track REPEAT repeats chapter track title disc etc
23. YAMAHA service personnel when any service is needed The cabinet should never be opened for any reason When not planning to use this unit for long periods of time 1 e vacation disconnect the AC power plug from the wall outlet Be sure to read the TROUBLESHOOTING section on common operating errors before concluding that this unit is faulty 17 Before moving this unit press STANDBY ON to set the unit in standby mode then disconnect the AC power plug from the wall outlet 18 Place this unit on a flat hard and stable surface 19 There must be sufficient room in front of the player for the disc tray to be opened 20 The mechanical parts of the set contain self lubricating bearings and must not be oiled or lubricated The unit is not disconnected from the AC power source as long as it is connected to the wall outlet even if this unit itself is turned off This state is called the standby mode In this state this unit is designed to consume a very small quantity of power WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE NOTE Pictures shown maybe different between countries Never make or change connections with the power switched on When playing DTS encoded CDs excessive noise will be heard from the analog stereo outputs To avoid possible damage to the audio system the consumer should take proper precautions when the analog stereo outputs of the player
24. ail in dark scenes while a negative value emphasizes contrast This function is available for signals output from COMPONENT video jacks only Choices 7 to 7 Initial setting 0 On screen menu HDMI Video Saturation Enables you to adjust the resolution depending on the Adjusts the video color saturation This function is not monitor you are using You can use this function only available for signals output from COMPONENT video when the HDMI output terminal is connected to a jacks and HDMI video signals HDMI compatible component Choices 7 to 7 Choices 480p 576p 720p 1080i Auto Initial setting 0 Initial setting 480p U S A model 576p U K Europe and Australia models Contrast Accentuates bright and dark parts of the video This l function is not available for signals output from Setting Examples COMPONENT video jacks and HDMI video signals Playback disc Choices 7 to 7 Initial setting 0 Sgueezed ER HDMI TV Monitor Monitor E 4 3 Aspect i Video shape settings settings playing source Personal will be chosen automatically Squeeze when you change the value in the following menus Full Normal 2 Saturation Contrast Brightness and Sharpness Widescreen 1 Auto 3 NE l 576p Through Through This function is not available for signals output from Squeeze re by Dot COMPONENT video jacks and HDMI video signals 720p Normal 2 Through Choices Rich Natural Soft Animation Personal
25. and 16 22 05 24kHz Full decoding of Dolby Digital DTS and MPEG multi channel sound analogue stereo sound Dolby Surround compatible downmix from Dolby Digital multi channel sound 3D Sound for virtual 5 1 channel sound on two speakers Dolby Pro Logic II 5 1 ch decoding from the stereo source SA CD AUDIO PERFORMANCE D A Converter DSD SA CD fs 2 8224 MHz Max output voltage 0 dB 2 V rms Signal Noise Ratio 115 dB Dynamic Range 107 dB Total Harmonic Distortion 1 kHz 0 0017 AUDIO PERFORMANCE Without upsampling DA Converter 24 bits DVD fs 96 kHz 2 Hz 44 kHz CD Video CD fs 44 1 kHz 2 Hz 20 kHz Signal Noise Ratio 115 dB Dynamic Range 103 dB DVD 48 kHz 24 bit Total Harmonic Distortion 1 kHz 0 0017 DVD 48 kHz 24 bit CONNECTIONS SCART Euroconnector x1 Europe model only Y Pb Cb Pr Cr Cinch 3x green blue red S Video Output Mini DIN 4 pins Video Output Cinch yellow x1 Audio Mixed 2 ch Output Cinch white red Digital Output 1 coaxial optical 6 channel analogue output Audio Main L R Cinch white red Audio Surround L R Cinch white red Audio Centre Cinch blue Audio Subwoofer Cinch black HDMI TYPE A xl IEEE1394 4 pins x2 CABINET Dimensions w x hx d 435 x 100 x 314 mm Weight Approx 5 6 kg POWER SUPPLY Power inlet U S A and Canada models AC120V 60 Hz Australia model AC240V 50 Hz U K and Europe models AC230V 50 Hz General model AC110 240V 50 60 Hz Power usage App
26. and the settings of Program menu items see the descriptions followed by FTS video audio program on page 26 View Rotate Rotates a JPEG image Choices 180 90 0 90 180 Initial setting 0 Zoom Activates the zoom function A cursor will be displayed on screen Move the cursor using the A V lt 1 buttons then select a size by pressing the ENTER button repeatedly To exit zoom mode press RETURN RESUME repeatedly until the cursor disappears from the screen Chapter preview Plays the first 10 seconds of each chapter track on the disc Pressing SCAN on the remote control performs the same function as well Choices On Off Initial setting Off 14 Angle some DVD discs feature a multiple angle function enabling you to watch certain scenes from various angles Function availability and the number of camera angles vary according to the disc Page Turns pages of DVD Audio still images Play option DVD Video Mode some DVD Audio discs include DVD Video contents that can be played on conventional DVD Video players To play such contents select On The setting returns to Off when you eject a disc or turn the unit to standby mode Choices On Off Initial setting Off Audio Selects the sound format and audio language Available choices are determined by the disc Disc Navigation You can direct to a track etc by using this menu Subtitle Selects the subtitle language Available choic
27. are connected to an amplification system To enjoy DTS Digital Surround playback an external 5 1 channel DTS Digital Surround decoder system must be connected to the digital output of the player LASER SAFETY This unit employs a laser Due to possible eye injury only a qualified service person should remove the cover or attempt to service this device CAUTION VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AVOID EXPOSURE TO BEAM LASER DIODE PROPERTIES Type Semiconductor laser GaAlAs Wave length 650 nm DVD SA CD 790 nm VCD CD Output Power 7mW DVD SA CD VCD CD DANGER This unit emits visible laser radiation when open Avoid direct eye exposure to beam When this unit is plugged into a wall outlet do not place your eyes close to the opening of the disc tray and other openings or look inside Table of Contents Introduction 2 Patent mformanon eene 2 Playable disc TOLIMALS si kingiideed ebe 2 Region management information cesses 3 Supplied EE 3 Installing batteries in the remote control 3 Usine the remote control erede kl eoe cue 4 Mante nance rahest kaante aa taa Nd oa M Ada a 4 Functional Overview 5 FROME Daniel aim to n etos ret etude fetta Lo 5 Rear pone Lissabon ei tias om tb ele oases 6 Remote CONU Ol nea eebe eld pa t 7 Preparation 8 Audio dee E 8 Digital audio connections ccecseesseessessssssensttseaaeeeas 8 i LINK components connection
28. button Press the lt button to select a rating from 1 through 8 for the disc Rating 0 Parental Control is not active The disc plays in full Operation Ratings 1 to 8 If you set a rating for the player all scenes with the same rating or lower will be played Higher rated scenes will not be played unless an alternative that has the same rating or lower is available on the disc If no suitable alternative is available playback will stop and the four digit code will be required to proceed Press the ENTER OK button then press the ON SCREEN button to exit the On screen menu Country You can apply a rating system associated with a specific country to the Parental Level control When the disc playback is stopped press ON SCREEN on the remote control The On screen menu appears Go to Enter PIN Setup gt Access gt Enter PIN by using the A V lt 1 buttons then press the D gt button Enter your four digit PIN Press the A V button to select Country then press the button Select a country using the A V button Press the ENTER OK button to confirm your selection and exit Changing the four digit PIN When the disc playback is stopped press ON SCREEN on the remote control The On screen menu appears Go to Enter PIN Setup gt Access gt Enter PIN by using the AV lt ID gt buttons then press the gt button Press the V button to highlight Change PIN then press the button Ente
29. by DTCP or the amplifier connected to this unit does not allow transmission Note The i LINK indicator located on the front panel of this unit lights only when i LINK is selected for an AV amplifier connected to this unit via an i LINK interface Even if Off is selected for Audio Output in the on screen menu the i LINK indicator lights whenever i LINK is selected on the connected AV amplifier 19 Operation Notes a E Unless otherwise stated all operations described Playing a disc herein are based on remote control usage 1 Insert the disc and close the tray Some operations can be carried out using the On Playback starts automatically screen menu on the TV screen gt The TV screen and the player s front panel display show the disc type information and playing time 2 When the Disc Menu appears on the TV screen use the B asi C playb a ck A V lt D buttons or the numerical buttons on the remote control to select an option and continue 1 Press STANDBY ON b to turn on the unit playback 2 Press OPEN CLOSE A on the front panel to open the If the titles are numbered press the numerical buttons or disc tray use the A V button to select the desired title in the menu 3 Place the disc in the tray with the label facing up par 4 Press OPEN CLOSE A again to close the tray 3 To stop playback press the STOP button gt READING appears in the Status window on TV and on the player s front panel display
30. c into the unit or the unit may be damaged SAUD l Og AUDIO lt a VIDEO RO a eg RW AD Wise e USE MEE USE DIGITAL VIDEO a SUPER VIDEO DIGITAL AUDIO DIGITAL AUDIO CD im Tere re Elei VIDEO CD DVD R DVD ReWritable DIGITAL AUDIO ReWritable This manual refers to disc types using the following symbols DVD Audio DVD Video Video CD SA CD Super Audio cp udio CD wes e Se al VDA icon includes Super Video CD Notes This unitis designed for use with SA CD DVD Video DVD Audio Video CD Super Video CD Audio CD CD R and CD RW MP3 and JPEG supported DVD R and DVD RW DVD R and DVD RW CD R and CD RW discs cannot be played unless they have been finalized DVD R and DVD RW discs cannot be played unless they have been finalized DVD R and DVD RW discs must be recorded in Video format and must be finalized Some discs cannot be played depending on disc characteristics or recording conditions Be sure to use only CD R and CD RW discs from reliable manufacturers Dolby Digital DTS Digital Surround and MPEG digital audio are supported PAL and NTSC are supported This unit features the PAL and NTSC video system converting function to allow you watching the different types of video discs on one TV see TV System NTSC PAL conversion on page 15 Do not use any non standard shaped discs heart etc Do not use discs that have tape scales or paste o
31. causare l esposizione a radiazioni di livello pericoloso PRECAUCI N El uso de los controles o los procedimientos de ajuste o utilizaci n diferentes de los especificados en este manual pueden causar una exposici n peligrosa a la radiaci n VOORZICHTIG Gebruik van bedieningsorganen of instellingen of uitvoeren van handelingen anders dan staan beschreven in deze handleiding kunnen leiden tot blootstelling aan gevaarlijke stralen CAUTION Visible and invisible laser radiation when open Avoid exposure to beam CLASS 1 LASER PRODUCT LASER KLASSE 1 PRODUKT LUOKAN 1 LASERLAITE KLASS 1 LASER APPARAT PRODUIT LASER DE CLASSE 1 General information The unit is not disconnected from the AC power source as long as it is connected to the wall outlet even if this unit itself is turned off This state is called the standby mode In this state this unit is designed to consume a very small quantity of power L appareil n est pas isol de la source d alimentation aussi longtemps qu il reste branch sur une prise murale m me lorsqu est teint Il est alors dit en mode Veille Dans ce mode appareil consomme tr s peu de courant Das Ger t ist nicht vom Netz getrennt solange der Netzstecker noch mit der Wandsteckdose verbunden ist selbst wenn das Ger t ausgeschaltet wurde Dieser Betriebszustand wird als Bereitschaftsmodus bezeichnet In diesem Zustand nimmt das Ger t eine sehr ge
32. discs single layer dual layer and hybrid discs Each type may contain two areas of recorded information a High Quality Stereo area and a High Quality Multi channel area A single layer disc can contain both information areas A dual layer disc can contain both information areas Double the information can be stored on the disc thanks to the second layer A hybrid disc can contain both information areas and also a second standard CD layer making it playable on standard CD players Recorded information may vary per area as indicated in the disc inlay You can select areas before or during playback while you are playing SA CD via the remote control or via the On screen display on your TV SA CD Disc Types Dual layer disc Single layer disc at Ca ed CP HD layer Hybrid layer disc HD layer CD layer HD layer AR SUPER AUDIO CD Hybrid SA CD Disc CD layerthat plays on any CD player High Density layer containing High Ouality DSD Stereo High Ouality DSD Multi channel SA CD contains only TRACKS Select tracks using the playlist on the screen or by pressing the numerical buttons If SA CD text is available on the disc it will be displayed on the TV screen 22 GA lt HD layer gt ADD Multichannel area TRACK 1 if available TRACK 2 TRACK 3 lt HD layer gt Stereo area TRACK 1 if available TRACK 2 TRACK 3 CD layer TRACK 1 in Hybrid TRACK 2 discs on
33. ect a language for audio subtitles NR On screen menus or DVD menus The selected languages will be used for all discs until you modify x your settings If the selected language is not available on the disc the d Center Di Front Distance A default language designated by the disc will be applied istance Default subtitle Selects a default subtitle language This setting also applies to DVD menu items Rear Distance Menu Language Selects a language for the On screen display Default Audio Selects a default audio language Speakers Use this menu to specify speaker size on off status and speaker distance to optimize your listening environment Placing all speakers except for the subwoofer at equal distances from the listener is the most ideal way of the speaker positioning in 5 1 channel system Set the following menu items to create the better listening Front Distance Sets the distance from your listening place to the front speakers We recommend to place the front left speaker and right speaker at the same distance from the listening point Choices 1 to 12 m Initial setting 1 9 m environment Centre Distance You can use the following 8 settings to select the size Sets the distance from your listening place to the center and layout for your speakers speaker Choices Varies depending on the Front Distance Speaker Size Layout setting Initial setting 1 9 m Fem center Surround Subwoof
34. ed via 1 LINK Notes This unit supports i LINK AUDIO allowing you to transfer audio signal information to other components compatible with i LINK AUDIO However because this unit does not support i LINK VIDEO you cannot transfer video information to other components Do not disconnect i LINK cables or switch off any components connected using i LINK while this player is turned on Copy protected 96 kHz DVD Video discs are downsampled to 48 kHz when using an i LINK connection You can connect up to 16 i LINK components to this unit Audio Output Change this setting to Off if an 1 LINK compatible component is still connected but you do not want to output signals using 1 LINK Reset to On to use the 1 LINK interface Choices On Off Initial setting On Note When audio data is transferred via an i LINK connection analog digital and HDMI audio signals are muted Connection Status This screen shows components connected using the i LINK interface and the transfer capabilities of each component with respect to Dolby Digital DTS and MPEG audio formats Choices Component 1 Component 2 Initial setting Component 1 Screen Sample lt RX Z9 e Dolby D gt Dolby D e DTS gt DTS MPEG gt PCM 1 LINK Connection Status Notes If PCM is selected for Digital Output in Setup Audio Menu all signals are converted to PCM format befo
35. er 3 Note The available range of choice differs depending on Small j Ge a Rear Distance Sets the distance from your listening place to the rear speakers We recommend to place the rear left speaker and rear right speaker at the same distance from the listening point l es yan Choices Varies depending on the Front Distance setting Initial setting 1 9 m Notes Note These settings are effective only on analog output EE signals the Front Distance setting Whenplaying DVD Audio with a sampling freguency l S of over 88 2 kHz all speaker sizes are set to Large Front Size and the subwoofer is set On regardless of the Specifies the front speaker size settings you adjusted Choices Large Small Initial setting Large Centre Size Specifies the center speaker size Choices Large Small Off Initial setting Large 17 On screen menu Surround Size Specifies the surround speaker size Choices Large Small Off Initial setting Large Subwoofer If you wish to use a subwoofer select On Otherwise select Off Choices On Off Initial setting On Note You may not be able to make settings that match your speaker layout DVD CD Mode Adjusts the volume of each speaker for audio playback excluding SA CDs If you adjust the volume level for any speaker the volume level for the other speakers is adjusted accordingly Front R Vol Choices 6 to 6 Initial setting
36. es are determined by the disc Search Frame by Frame Advances or reverses one frame at a time This function is available for video discs only Previous frame is not available for VCD and SVCD Fast Selects a speed for fast forward or fast reverse playback Choices 32 8 4 1 4 8 32 Initial setting 1 Time You can move to a certain spot by indicating the elapsed time Slow Selects a speed for the slow forward or slow reverse playback Choices 1 1 2 1 4 1 8 0 1 8 1 4 1 2 1 Initial setting 0 Slide Show Use this feature for JPEG slide show playback Picture time Sets the duration for each image Choices Slow Medium Fast Initial setting Medium Setup 7 Access Disc lock This function enables you to restrict others from accessing certain discs If this setting is on you need to enter the four digit PIN to modify the Access menu settings before you can play the disc Choices On Off Initial setting Off Change PIN Enables you to change the four digit PIN To change the four digit PIN enter the current PIN first then enter the new four digit PIN Enter PIN Enter the four digit PIN to unlock the disc or to display the Access menu Parental level DVD movies may contain scenes that are unsuitable for children Therefore some discs contain parental control information that may apply to the entire disc or to certain scenes Ratings are country specific
37. essive signals This setting will enable you to enjoy accurate color reproduction and high quality images This unit features DCDi circuit The PROGRESSIVE indicator on the front panel lights up during progressive playback Notes In the PROGRESSIVE mode 4 3 aspect images are stretched horizontally on the wide screen TV We recommend to change the TV screen s aspect ratio settings for progressive signals if you wish to watch the original aspect ratio images without distortion You can also change the aspect ratio settings in the 4 3 Aspect parameter in the On screen menu Some TVs and projectors are not compatible with this unit If you notice picture distortion when outputting the progressive signals switch the SCAN MODE selector to INTERLACE CONSUMERS SHOULD NOTE THAT NOT ALL HIGH DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS TO BE DISPLAYED IN THE PICTURE IN CASE OF 525 OR 625 PROGRESSIVE SCAN PICTURE PROBLEMS IT IS RECOMMENDED THAT THE USER SWITCH THE CONNECTION TO THE STANDARD DEFINITION OUTPUT IF THERE ARE QUESTIONS REGARDING OUR VIDEO MONITOR COMPATIBILITY WITH THIS MODEL 525P AND 625P DVD PLAYER PLEASE CONTACT OUR CUSTOMER SERVICE CENTER This unit is compatible with the complete line of YAMAHA products including the projectors DPX 1000 DPX 1100 LPX 500 LPX 510 and the plasma monitor PDM 4210 10 mmh Switching on Connect the AC power cord to t
38. esume icon is on screen or press RETURN RESUME when the playback is not DVD Title 1 Chapter 1 DVD AD Group 1 Track 1 performing Chapter 2 Track 2 E Gier 3 fat 3 gt Playback resumes from the point where the playback was interrupted Title 2 Chapter 1 Group 2 Track 1 Chapter 2 Track 2 Note Chapter 3 Track 3 The Smart Resume function is also compatible with VCDs and SVCDs 20 DVD features Menu DVDs may contain menus to navigate the disc and access special features such as audio language selection subtitle language selection and other options Press MENU gt If the disc includes a menu it will appear on screen To access to the disc menu press TITLE CHAP first then press MENU Press the appropriate numerical buttons or use the A V lt D buttons to highlight your selection in the DVD menu then press the ENTER OK button to confirm To remove the menu press MENU again Camera angle Some discs contain scenes that were shot simultaneously from various angles This unit allows you to select the desired camera angle When this unit encounters a scene shot from multiple angles it will so indicate in the screen gt The angle icon remains displayed until multiple angles are no longer available Press ANGLE repeatedly or use A V buttons to select the desired angle gt Playback shifts to the selected angle You can also access the angle function in the On screen menu Toolbar gt Vi
39. ew gt Angle Changing the audio language and format Press AUDIO on the remote control to activate the audio language selection menu Choose a language by pressing the AUDIO button repeatedly or by pressing the A V buttons Press the ENTER OK button to confirm Note You can also select an audio language and an audio format also in the On screen menu Toolbar 3 Play option gt Audio Subtitle language Press SUBTITLE on the remote control to activate the subtitle language selection menu Choose a language by pressing the SUBTITLE button repeatedly or by pressing the A V buttons Press the ENTER OK button to confirm Note You can also select a subtitle language in the On screen menu Toolbar gt Play option gt Subtitle Operation DVD Audio features The DVD Audio is developed for the sole purpose of creating high quality pure sound with Linear PCM and Packed PCM Loss less coding in up to six audio channels The sampling frequency of 192 kHz 24 bits are supported Moreover many DVD Audio discs offer slide show and page turn capabilities When you play a down mix prohibited disc DOWN MIX indicator turns off Multi channel tracks will play regardless of the Analog output settings in the On screen menu The MIXED 2CH jacks output the front L and R signals only Changing pages Some DVD Audio discs contain information pages that can include photo galleries artist biographies lyrics e
40. he power outlet Switch on the TV and this unit Set the TV to the correct Video IN channel e g EXT1 EXT2 AV1 AV2 AUDIO VIDEO etc Refer to your TV owner s manual for detail gt The front panel display lights up and the default screen appears on the TV If you are using an external equipment e g audio system or receiver turn them on and select the appropriate input source that was used to connect to this unit Refer to the equipment owner s manual for detail Note Ifyou do not have a proper picture or sound refer to Troubleshooting section Setups before the initial playback We recommend to setup some of the basic menu items before the initial playback AUDIO SOUND DIMMER DIRECT MODE O KYI _ ON SCREEN REPEAT A B SHUFFLE SCAN Press STANDBY ON dh to turn on the unit Press ON SCREEN gt On screen menu is displayed on the screen Follow the procedure described below to set the following menu items Menu Language see page 17 2 3 You can select the language displayed in the On screen menu Go to Menu Language Setup gt Language gt Menu Language by using A V lt ID gt buttons on the remote control then press gt Choices are displayed on the right column Select a language to be displayed in the On screen menu by using A V buttons Press lt J to return to the previous menu
41. he remote control Do not use old batteries with new ones Check your package to make sure it contains the Do not use different types of batteries such as following items alkaline and manganese together Read the battery Remote control Batteries x2 AA R6 UM 3 packaging carefully Different types of batteries may C be the same shape or color eS e If the batteries leak dispose of them immediately Avoid touching the leaked material or letting it come into contact with clothing etc Clean the battery compartment thoroughly before installing new batteries YAMAHA Audio Video cable Power cable CA GA Introduction Using the remote control Remote control sensor Point the remote control at the sensor within approximately 6 m 20 feet of the unit Handling the remote control s Do not spill water or other liquids on the remote control Do not drop the remote control Do not leave or store the remote control in the following types of conditions high humidity such as near a bath high temperature such as near a heater or stove extremely low temperature dusty places Maintenance Cleaning the cabinet e Useasoftcloth slightly moistened with a mild detergent solution Do not use a solution that contains alcohol spirits ammonia or abrasives Cleaning discs e When a disc becomes dirty clean it with a cleaning cloth Wipe the disc from the center out
42. ideo output Initial setting Off may not display properly if a resolution output setting not supported by the HDMI compatible monitor you are using is Set To return to the initial setting press PLAY 3 0 gt 2 gt 9 gt STOP on the remote control Do not perform this operation while playing back a disc on this unit ClearVoice Increases the relative volume of dialog for easy listening at night This function is available for only certain multi channel discs Choices On Off Initial setting Off Picture Video shift Adjusts the position of the image on the screen by scrolling it to the left or right Choices 1 to 7 Initial setting 4 13 On screen menu Night mode When set to On the dynamics of the sound output is optimized High volume output is softened enabling you to watch your favorite action movie without disturbing others Choices On Off Initial setting Off Toolbar 7 Program You can create your own playlist using this menu First go to Tracks then select the tracks chapters etc to include in your playlist The programmed playlist will be activated when you choose On in the Program menu Clear all Deletes all Programmed contents Program Set the FTS program playback on or off Choices On Off Initial setting Off Tracks Selects tracks and chapters for your FTS list Playlist Shows the programmed FTS list Note For details about FTS
43. in your plug proceed as follows Connect the blue wire to the terminal marked N or coloured black Connect the brown wire to the terminal marked L or coloured red e Do not connect either wire to the earth terminal in the plug marked E or e or coloured green or green and yellow Before replacing the plug cover make certain that the cord grip is clamped over the sheath of the lead not simply over the two wires Copyright in the U K Recording and playback of material may require consent See Copyright Act 1956 and The Performer s Protection Acts 1958 to 1972 CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure ATTENTION L emploi de commandes de r glages ou un choix de proc dures diff rents des sp cifications de cette brochure peut entrainer une exposition a d ventuelles radiations pouvant tre dangereses ACHTUNG Die Verwendung von Bedienungselementen oder Einstellungen oder die Durchf hrung von Bedienungsvorg ngen die nicht in dieser Anleitung aufgef hrt sind kann zu einem Kontakt mit gef hrlichen Laserstrahlen f hren OBSERVERA Anv ndning av kontroller och justeringar eller genomf rande av procedurer andra n de som specificeras i denna bok kan resultera i att du uts tter dig f r farlig str lning ATTENZIONE Uso di controlli o regolazioni o procedure non specificamente descritte pu
44. k ytt j n turvallisuusluokan 1 ylitt v lle lasers leilille Huom Toiminnanvalitsin STANDB Y ON on kytketty toisiopuolelle eik se kytke laitetta irti s hk verkosta Sis nrakennettu verkko osa on kytkettyn s hk verkkoon aina silloin kun pistoke on pistorasiassa VARO AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA NAKYMATTOMALLE LASERSATEILYLLE ALA KATSO SATEESEEN VARNING OSYNLIG LASERSTRALNING NAR DENNA DEL AR OPPNAD OCH SPARREN AR URKOPPLAD BETRAKTA EJ STRALEN Important Note for Users in the UK Mains plug This apparatus is fitted with an approved 13 Amp plug To change a fuse in this type of plug proceed as follows 1 Remove fuse cover and fuse 2 Fix new fuse which should be a BS1362 5 Amp A S T A or BSI approved type 3 Refit the fuse cover If the fitted plug is not suitable for your socket outlets it should be cut off and an appropriate plug fitted in its place If the mains plug contains a fuse this should have a value of 5 Amp If a plug without a fuse is used the fuse at the distribution board should not be greater than 5 Amp Note The severed plug must be disposed of to avoid a possible shock hazard should it be inserted into a 13 Amp socket elsewhere How to connect a plug The wires in the mains lead are coloured with the following code blue neutral N brown live L As these colours may not correspond with the colour markings identifying the terminals
45. lby Pro Logic and the double D symbol are trademarks of Dolby Laboratories DIGITAL DTS and DTS Digital Surround are registered trademarks of Digital SURROUND Theater Systems Inc DCD is a trademark of Faroudja a division of Genesis Microchip Inc byFAROUDJA Mom HDMI the HDMI logo and High OEE e Definition Multimedia Interface are trademarks or registered trademark of HDMI Licensing LLC This product incorporates copyright protection technology that is protected by method claims of certain U S patents and other intellectual property rights owned by Macrovision Corporation and other rights owners Use of this copyright protection technology must be authorized by Macrovision Corporation and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation Reverse engineering or disassembly is prohibited i LINK and the i LINK logo g are trademarks of Sony Corporation This product complies with the following 1 LINK interface specifications 1 IEEE Std 1394a 2000 Standard for a High Performance Serial Bus 2 Audio and Music Data Transmission Protocol 2 1 Following the standard for AM824 sequence adaptation layers the product is compatible with IEC60958 bitstream DVD A and SA CD media Playable disc formats This unit can play the disc types associated with the logos shown below Do not attempt to load any other type of dis
46. ly TRACK 3 Playing a disc Insert the disc and close the tray Playback starts automatically gt The TV screen will display the current playing status and current playing track list in the area Playback will stop at the end of the disc To stop playback press STOP Analog output setting in the On screen menu Setup gt Audio Menu gt Analog output allows you to specify which area of SA CD to play automatically when you insert the disc When you select Stereo stereo area is selected When you select the other choices multi channel area 1s selected If you set the playback area that the disc does not contain this unit automatically play the available area on the disc Sound mode SA CD playback You can change the playback area of the SA CD by pressing the SOUND MODE button on the remote control Press the SOUND MODE at any time to select the multi channel area or the stereo area in the HD layer Press the SOUND MODE button when the disc is stopped to select the CD layer Select the area by pressing the SOUND MODE button repeatedly On hybrid discs with SA CD and CD layers the player will always start playing the SA CD layer The SA CD indicator lights only when the SA CD layer is selected You can program the playlist in the same area only Audio CD Audio CDs contain only TRACKS They can be played on this unit with the audio output connected to a stereo system or to your TV Select tracks using
47. n them or damage to the unit may result Do not use discs with surfaces printed by a commercial label printer Some DVD discs require specific features or allow only limited function during playback Prohibited mark may appear on the TV screen to indicate that a function is unavailable Photo CD CD ROM DVD ROM DVD RAM CDV and nonstandard CD discs cannot be played on this unit Introduction Region management Installing batteries in the information remote control The unit is designed to support the Region Management Insert the batteries in the correct direction by aligning System Check the regional code number on the disc the and marks on the batteries with the polarity package If the number does not match the unit s region markings and inside the battery compartment number see table below or see back of unit the unit may be unable to play the disc Region number of the unit Discs that can be a played Example U S A model 1 Remove the back cover U K and 2 Insert the two supplied batteries AA R6 UM 3 into Europe models we Be the battery compartment 3 Close the back cover Australia peu model v Se Replace worn batteries Worn batteries limit the operating range of the remote control Replace both batteries at the same time Replace both batteries if you notice a decrease in the Suppl ied accessories operating range of t
48. nplug the AC cord from the AC outlet for 5 10 seconds Certain operations may not be permitted by the disc Refer to the instructions for the disc Use a cleaning CD DVD to clean the lens before sending this unit in for repair Change the parameter of the Video Shift menu in the On screen menu Preferences gt Picture gt Video shift See page 12 13 SCMS copy protected discs cannot be recorded digitally Try recording by analog jacks If the problem is not listed above or if the instructions fail to help turn off the power to the unit disconnect the power cable and contact the nearest authorized YAMAHA dealer or service center Specifications PLAYBACK SYSTEM DVD Audio DVD Video Super Audio CD Stereo Multi channel and Hybrid disc DVD R DVD RW DVD R DVD RW Video Format Video CD VCD Super Video CD SVCD CD Audio CD DA CD R CD RW CD DA VCD SVCD MP3 JPEG TV STANDARD PAL 50 Hz NTSC 60 Hz Number of lines 625 525 Playback Multistandard PAL NTSC VIDEO PERFORMANCE RGB output YUV output 0 7Vpp into 75 ohm Y 1Vpp into 75 ohm Pb Cb Pr Cr 0 7Vpp into 75 ohm Y 1Vpp into 75 ohm C 0 3Vpp into 75 ohm PAL C 0 286Vpp into 75 ohm NTSC Vpp into 75 ohm S Video output Video output AUDIO FORMAT DSD Multi channel and Stereo Dolby Digital DTS MPEG Compressed Digital PCM Packed PCM fs 48 96 192 and 44 1 88 2 176 4kHz 16 20 24bits MP3 1509660 32 44 1 48
49. ntrol 1 Select Fast in the On screen menu Toolbar gt Search gt Fast 2 Press the lt ID gt button to select the desired speed 3 Select 1 to resume playback at normal speed Slow motion DIDAD DWV NCD OSD control 1 Select Slow in the On screen menu Toolbar gt Search gt Slow then press gt Playback pauses 2 Press lt ID gt to select the desired speed 1 1 2 1 4 or 1 8 reverse or 1 8 1 4 1 2 or 1 forward 26 3 Select 1 to resume playback at normal speed 4 If you press the lI button the speed will be set to zero PAUSE b To exit slow motion mode press PLAY Notes You can use this function for DVD Audio while the disc is playing its video content Slow motion in reverse is not available for VCDs or SVCDs Still picture and frame by frame playback DAD DDJ NCD Key control You can activate frame by frame playback by pressing the PAUSE repeatedly OSD control 1 Select Frame by Frame in the On screen menu Toolbar gt Search gt Frame by Frame then press gt Playback pauses 2 Press the lt J button to select the previous or next picture frame 3 To exit frame by frame playback press PLAY Note You can use this function for DVD Audio while the disc is playing its video content Time search NDAJ DVN A D NCD 2 D The Time Search function enables you to start playback at a specific time on the disc 1 Select Time
50. nu appears on the screen and asks you which file to play Playback will stop at the end of the disc To stop playback press STOP Choosing an Album Track to playback You can choose an Album Track to playback from the list displayed in the TV screen In the playlist press A V to select the Album Track to playback Press lt 1 D gt to select the Album Track in the next layer to playback MP3 text MP3 CD discs may contain text information called ID3 Tag e g track name album name artist name etc that can appear on the TV screen during playback JPEG This player can playback JPEG format pictures on a personally recorded CD R RW disc or commercial CD Disc structure Roll 1 Image Image 2 Image 3 Roll 2 Image 1 Image 2 Image 3 JPEG disc features The JPEG format ISO 9660 format supports the following e Max nested directories 8 levels e Max numbers of rolls are 99 e Max numbers of pictures are 999 e The files with the extensions of JPEG jpeg JPG or jpg The following types of disc and conditions are not supported e Discs with playback control functions e The discs that have any types of file other than MP3 and JPEG The simultaneous playback of the JPEG and MP3 files Progressive JPEG formatted discs Non finalized discs UDF formatted discs Notes The disc read time may exceed 10 seconds if the disc has large amount of pictures The read
51. ommands during playback Cannot read CDs DVDs The picture is not displayed in a proper position on the screen Connect record MP3 Solution Check to ensure that the AC power cord is properly connected Check to ensure that the TV is switched on Check the video connection Occasionally a small amount of image distortion may be visible This is not a malfunction Make sure the NTSC PAL setting on the DVD player matches the video signal of your television See TV System NTSC PAL conversion on page 15 Adjust the volume Check that the speakers are connected correctly Check the digital connections Check the settings menu to ensure that the digital output is set to All or PCM only Check to ensure that the audio format of the selected audio language matches your receiver capabilities Check that the SCART cable is connected to the correct device see Audio connection on page 8 Check that the disc label is facing up Determine if the disc is defective by trying another disc Check the disc for fingerprints or scratches Clean with a soft cloth wiping from center to outside edge Reset the unit by switching the player off then on again Aim the remote control directly at the sensor on the front of the player Reduce the distance to the player Replace the batteries in the remote control Re insert the batteries with their polarities signs as indicated To completely reset the player u
52. progressive scan mode the output signals from the VIDEO and S VIDEO jacks are same as the format of the disc you play Some image distortion occurs when switching the NTSC and PAL mode f your TV does not accept the selected mode while you change the TV System setting the screen will be distorted so that you cannot recognize the On screen menu When it occurs you can change the TV System settings by the remote control operations Follow the procedures below Choosing PAL Press PLAY gt 2 gt 5 gt 6 gt PLAY on the remote control Choosing NTSC Press PLAY gt 2 gt 5 gt 7 gt PLAY on the remote control Do not perform this operation while playing back a disc on this unit 15 On screen menu Audio Menu Digital output Enables you to specify the type of digital output that best suits your AV receiver or HDMI monitor receiver Select PCM only if your receiver or HDMI monitor receiver is not capable of decoding multi channel audio Select All if you connected this unit s digital out jacks to a multi channel decoder receiver Choices Off PCM only All Initial setting All Note SA CD audio signal is not output from DIGITAL OUT jacks Analogue output Enables you to specify the type of analog output suitable for your AV receiver Choices Stereo Dolby Surr Compat 3D sound Multi channel Initial setting Multi channel Stereo
53. r the current four digit PIN again then enter a new four digit PIN Enter the new PIN a second time Press the ON SCREEN button to exit the menu The new four digit code is in effect If you forget your four digit code Press amp OPEN CLOSE to remove the disc then press A OPEN CLOSE again to close the tray Press ON SCREEN on the remote control The On screen menu appears Go to Enter PIN Setup gt Access gt Enter PIN by using the A V lt ID gt buttons then press the D gt button Press the LL button for four times Enter New PIN appears on screen Enter your new four digit PIN Note The factory default PIN is 0000 29 30 Troubleshooting WARNING Under no circumstances should you try to repair the system yourself as this will invalidate the warranty Do not open the system as there is a risk of electric shock If a fault occurs first check the points listed below before taking the system in for repair Problem No power No picture Distorted picture Completely distorted picture or black and white picture when playing a DVD Super Audio CD or Video CD No sound or distorted sound No audio at digital output No sound and picture Disc does not play Picture freezes momentarily during playback Fails to return to start up screen when disc is removed No response to remote control Buttons do not work or player stops responding No response to some operating c
54. re being output An asterisk appears next to the name of the component initially recognized by this unit The audio signal output format is determined by the transfer capabilities of the component and signals are output to all connected components The component name is displayed only when the i LINK receiver component connected to this unit supports i LINK AUDIO The component name is not displayed for DVD players or DV camcorders If the i LINK component connected to this unit does not contain any device name information is displayed On screen menu AutoPlay Select You can use this setting to specify a receiver for automatically switching the input to this player when you start playback of a disc Choices Off Component 1 Component 2 Initial setting Off Information about the operational status of this unit is displayed in the front panel display as follows Displayed when data transfer is not possible because you are already using the allowable BUS FULL maximum bandwidth of the i LINK bus or when 17 or more 1 LINK components are connected to this unit LINKING Displayed when this unit is checking a new i LINK connection Displayed when this unit and the 1 LINK LOOP CHECK component are connected in a loop where the output signal is returned to the original component Displayed when an i LINK connection was activated but either the new connection 1s NO OUTPUT not recognized
55. ringe Menge Strom auf Enheten r inte urkopplad fran n tet sa lange som den r ansluten till v gguttaget ven om enheten 1 sig sj lvt r avst ngd Detta kallas for beredskapsl ge och i detta tillst nd konsumerar apparaten minimalt med str m L unit non scollegata dall impianto elettrico di casa sintanto che rimane collegata ad una presa di corrente anche se spenta Questo modo viene chiamato modo di attesa In esso l unit consuma una quantit molto bassa di energia per mantenere in memoria le impostazioni da voi fatte Aunque el propio aparato se encuentre apagado ste no se desconectar de la fuente de CA siempre que se mantenga enchufado a la toma de corriente Este estado recibe el nombre de modo de espera En este estado este aparato ha sido dise ado para consumir una cantidad muy peque a de energ a De stroomtoevoer naar het toestel 1s niet afgesloten zolang de stekker nog in het stopcontact zit zelfs niet als het toestel zelf uitgeschakeld is Deze toestand wordt standby waak of paraatstand genoemd Het toestel is ontworpen om in deze toestand CAUTION VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AVOID EXPOSURE TO BEAM ADVARSEL SYNLIG OG USYNLIG LASERSTRALING VED ABNING UNDGA UDS ETTELSE FOR STRALING ADVARSEL SYNLIG OG USYNLIG LASERSTRALING NAR DEKSEL APNES UNNGA EKSPONERING FOR STRALEN VARNING SYNLIG OCH OSYNLIG LASERSTRALNING NAR DENNA DEL AR OPPNAD BETRAKTA EJ STRALEN
56. rox 33 W Power usage standby lt 1W Specifications subject to change without notice 31
57. s sssessssessessessesesssseeee 8 Analog audio 6CH DISCRETE connection 8 Analog audio MIXED 2CH connection 9 Video COBHOCHOHS aede ire eerie i eia de d EO FR eR ee 9 HDMI component connections ssssseessesssesssssssssssssesss 9 SWITCHED ODE ooo ots oto boo Aba edat o rd 10 Setups before the initial playback 10 On screen menu 12 HEET 12 PIelelenCes Aere 12 KEIER A A A A ob e e mu 12 AON PICE ea R 12 Ste 13 SOUNG Aa 13 TOOD ETT a tanka 14 PrO TS COLE A aaa M D Cen T 14 AT 14 Play ODUOB EE 14 EE 14 e DE 15 e E 15 ACOE OS du oec LA M LAM br MEC a Mia 15 PALS ee eeneg 15 ENEE EE 15 Amio MGI EE 16 SACU A OS aaa SU aaa aaa alata t 17 eil EE 17 PVC ID NODC EE 18 SAC D leet 18 LLIN EE 18 Operation 20 Basie playback EE 20 DVD Video and DND Audo eene 20 PIasIng EE 20 SMart RES UNG icine Asc stb orta dee 20 DVD Catan Sea rere oni a alul 21 EE 21 TEE eege 21 Changing the audio language and format 21 SUD An e de vidina alad 21 DVD AUdIiO Te at fes a bei cus ewes akki sce EU bla LY DURO und 21 Chans me Pas eS canny nisa aktsia kokkade 21 Playing DOMUS OTOUPS E 21 pNVDSVideoVOge natike tisse ovi Maadlus 21 SA CD Super AudoCD 22 tree eebe ee 22 Sound mode SA CD plawvback 22 ee 23 lr 23 Video CD and Super Video CD eos 23 PA A dist sees nies meid Malik EE 23 Playback Control PBC EE 23
58. s recorded onto a CD R or CD RW by a computer Disc structure example MED Album 1 Folder Track 1 File Track 2 Album 1 1 Track 1 Album 2 Since the MP3 format can store several albums onto a disc a folder is assigned to an Album and a file is assigned to a Track MP3 disc features The MP3 CD format ISO9660 format support the following e MP3 files must have the extension MP3 or mp3 Max 30 characters Max nested directory is 8 levels Max album number is 99 Max track number is 999 e Supported VBR bit rate e Supported sampling frequency of 16 22 05 24 32 44 1 48kHz The following features are not supported for MP3 discs The discs that have any types of file other than MP3 and JPEG The simultaneous playback of the MP3 and JPEG files Chinese filenames and text Non finalized closed discs Discs recorded in UDF format 24 Additional note for MP3 disc playback The disc read time may exceed 10 seconds due to the large number of songs compiled onto one disc Multi session discs are supported The digital output signals of MP3 files are copy protected Downloading MP3 files from the internet or copying songs from your own legal discs is a delicate process Playing a disc Insert the disc and close the tray Playback starts and the playlist appears automatically If the disc includes both MP3 and JPEG files the selection me
59. t to the AV receiver and then to your TV This enables you to use one TV for several different video sources LD VCR etc by simply switching the input source selector on your AV receiver This unit features four types of video output jacks Component Video S Video and AV Connect the appropriate video output jack to your equipment Preparation j ki Ps Cs PR CR A COMPONENT IN Da B ns COMPONENT OUT S VIDEO IN COMPONENT IN HDMI component connections Use the HDMI connection cable to connect this unit to HDMI compatible components AV Projector VIDEO MI COMPONENT IN N Note You can use a HDMI to DVI conversion cable to connect this unit to DVI HDCP compatible components In this case no audio signals are output from this unit s jacks Preparation SCAN MODE selector This selector switches the type of output signal from the COMPONENT video jacks on this unit SCAN MODE Baum L INTERLACE PROGRESSIVE SCAN MODE DO00000009 000000000 AV COAXIAL OPTICAL DIGITAL OUT INTERLACE Select INTERLACE if you are connecting the component to a standard interlace format TV PROGRESSIVE Select PROGRESSIVE if your TV accepts NTSC progressive or PAL progr
60. tc Every time you press the PAGE button on the remote control the page is turned to the next Playing bonus groups Some discs contain bonus groups that require a four digit password to gain access In this case consult the disc jacket and other packaging for information While playback is stopped press TITLE CHAP button gt The group and track list is displayed on the TV screen Press the A V buttons to select a bonus group then press the button Enter a four digit password using the numeric buttons then press the ENTER OK button gt To exit from the password entry screen without entering the password press STOP Press the A V buttons to select a track then press the ENTER OK button DVD Video Mode some DVD Audio discs include DVD Video contents that can be played on conventional DVD Video players In the On screen menu Toolbar gt Play option 3 DVD Video Mode select On to play the DVD Video content or select Off for normal playback Notes The DVD AUDIO indicator lights up when a DVD Audio disc is playing When you set DVD Video mode ON the DVD AUDIO indicator turns off 21 Operation SA CD Super Audio CD The SA CD standard is based on Direct Stream Digital DSD technology This new direct stream digital format comprises a 1 bit system that has a digital sampling frequency that is 64 times higher than that of conventional audio CD There are three types of SA CD
61. ted to 2 ch 48 kHz or less Select 48 KHz if the connected equipment cannot process signals with a sampling frequency of 96 kHz or 88 2 kHz Choices 96 KHz 48 KHz Initial setting 96 KHz Notes Signals are converted to either 48 kHz or 44 1 kHz despite the above settings if the disc has copy protection If you select 96 KHz signals with a sampling frequency of over 96 kHz are converted to 2 ch 88 2 kHz or 96 kHz SA CD Direct Enables you with a suitable speaker system to bypass the bass management system for multi channel SA CD playback so you can enjoy the pure SA CD quality Choices On Off Initial setting Off Note When SA CD Direct is On the speaker settings will not be applied during SA CD playback HDMI Audio If you are not using HDMI audio output you should set this to Off If the monitor receiver connected to this unit using HDMI does not support HDMI audio signal input set this to Off Choices On Off Initial setting Off Notes Super Audio CD signals cannot be output using HDMI This unit can output the following audio signals using HDMI 32 44 1 48 kHz 2 ch PCM signals and bitstream signals Dolby Digital DTS and MPEG PCM signals with a sampling frequency of over 66 2 kHz are converted to 2 ch 48 kHz or 44 1 kHz When audio signals are being output by a HDMI component digital output signals are muted On screen menu Language Enables you to sel
62. time may vary depending on the file types and sizes Multi session discs are supported Playing a disc Insert the disc and close the tray gt Playback starts automatically gt Thumbnails are displayed on screen A chosen thumbnail can be displayed on full screen Move the cursor with A V lt 1 to select the thumbnail and press ENTER OK Press MENU to return to the thumbnail screen Press PLAY during a full screen mode gt The slide show starts To stop playback press STOP gt The slide show stops Operation Press MENU to return to the thumbnail screen When you press PAUSE the slide show pauses To return to the normal slide show press PLAY Repeat and shuffle function are also available for JPEG discs Slide show setting You can set the duration of each image Picture Time Picture Time Picture Time JPEG JPEG JPEG m m dech Picture Time Press ON SCREEN The On screen menu appears Go to Picture Time Toolbar gt Slide Show gt Picture time by using A V lt ID gt buttons then press gt Make a choice with A V Choices Slow about 8 sec Medium about 5 sec Fast about 2 sec To return to the previous menu press lt To exit from the On screen menu press ON SCREEN Rotating the image You can rotate the JPEG image Press ON SCREEN The On screen menu appears on the screen Go to Rotate Toolbar gt View gt Rotate by using A V lt D buttons
63. u Preparation 5 Analog output see page 16 2 3 Enables you to specify the type of analog output suitable for your AV receiver Select Multi channel if you are using a multi channel AV receiver with 6 ch discrete inputs If your AV receiver does not have 6 ch discrete inputs select one of Stereo Dolby Surr Compat or 3D sound Go to Analog output Setup gt Audio Menu gt Analog output by using A V lt ID gt buttons on the remote control then press gt Choices are displayed on the right column Select an item for the analog output signal by using A V buttons Press lt J to return to the previous menu 6 Digital output see page 16 Enables you to specify the type of digital output suitable for your AV receiver Select PCM only if your AV receiver is not capable of decoding multi channel audio Select All if you connected this unit s digital out jacks to a multi channel AV receiver Go to Digital output Setup gt Audio Menu gt Digital output by using A V lt ID gt buttons on the remote control then press gt Choices are displayed on the right column Select an item for the digital output signal by using A V buttons Press lt J to return to the previous menu Notes Press ON SCREEN again to exit from the On screen menu You can find the selection of the helpful menu items in Preference and Setup Go to Preference if you want to customize this unit for yo
64. um has more than one chapter or track When Shuffle Play within a title group album finishes the unit continues shuffle playback within the next title group album Press SHUFFLE during playback SHUFFLE appears on the screen for about two seconds To return to normal playback press SHUFFLE again AD WDD cc This function shuffles the playing order of tracks on a disc Press SHUFFLE during playback gt SHUFFLE appears on the screen for about two seconds To return to normal playback press SHUFFLE again Note For SA CD this function works in the currently selected area only Scan DVDAD VD D SAD VDJ ODD M Plays the first 10 seconds of each segment on the disc Press SCAN To continue playback at your chosen segment press SCAN again or press PLAY Note You can also access this function by selecting Chapter Preview in the On screen menu Zoom 24 ov YDD This function allows you to enlarge the video image and pan through the enlarged image during playback or pause Press ZOOM on the remote control or select Zoom in the On screen menu Toolbar gt View gt Zoom and press to enter zoom mode gt The cursor appears on screen Press the A V lt ID gt buttons to move around the image On screen Press the ENTER OK button to enlarge the image Each time you press the ENTER OK button the zoom factor changes from x1 to x2 to x4 to x8 To exit from zoom mode press ENTER OK repeatedly
65. ur personal requirement such as the Wake up timer Go to Setup if you want to set the operational status of this unit 11 On screen menu The On screen menu enables you to customize this unit to suit your requirements General operation Press ON SCREEN on the remote control gt The On screen menu appears on the screen e Program Preferences e View e Toolbar gt Play Option Setup e Search e Slide Show Y ea Toolbar Press A V lt ID gt to navigate the On screen menu and to change the settings Press ON SCREEN to exit from the On screen menu Preferences 0 Features Dimmer Adjusts the brightness of the front panel display You can use this function if the brightness of the front panel display disturbs your enjoyment of the home theater Choices Low Medium Normal Initial setting Normal Wake up timer Turns on the player from standby mode after a preset amount of time The timer is then reset to zero You can set the timer for up to 600 minutes Choices 0 to 600 minutes Initial setting 0 Status window Displays the current status of the player Select Off to suppress display of the Status window Choices On Off Initial setting On 12 Adv Picture Allows you to fine tune the following video parameters 4 3 Aspect You can adjust the aspect ratio of the projected images on the screen This function is only available for progressive scan and HDMI
66. uttons then press the D gt button Enter the four digit PIN of your own choosing Move to Disc lock menu using the A V buttons Select On or Off using the A V buttons Press the 1 button then press ON SCREEN to exit the On screen menu gt If you select On in the Disc lock menu unauthorized discs will not be played unless the four digit PIN is entered Notes Confirmation of the four digit PIN is necessary when e The PIN is entered for the very first time see above The PIN is changed or cancelled see Changing the four digit PIN on page 29 f you select Off in the Disc lock menu the FTS function will not be performed Authorizing discs When Disc lock is ON you must authorize discs before you can play them Insert the disc The Disc lock dialog will appear Enter your four digit PIN for Play once or Play always If you enter the four digit PIN for Play Once the disc can be played one time only You must re enter the code if disc is ejected or the power is turned off If you enter the four digit PIN for Play always the disc can be played anytime even when Disc lock is ON Notes The player memory can maintain 120 authorized Disc locked disc titles A disc title will be added to the list if Play always is selected Each time a Disc locked disc is played it will be added to the top of the list When the list is full 120 the last disc in the list
67. y change not only the audio language but also the audio format The selected format name will be displayed for several seconds in the status window SA CD audio signal is not output from DIGITAL OUT jacks If you wish to enjoy Dolby Digital DTS and MPEG you must connect this unit to the AV receiver that support those i LINK components connections Use an 1 LINK connection cable of approximately 3m 10 feet or less to connect this unit to 1 LINK compatible components refer to page 18 for details Analog audio 6CH DISCRETE connection Connect a receiver with multi channel audio input terminals to enjoy surround sound with no sampling frequency limitation We recommend this connection to obtain maximum performance of SA CD discs and DVD Audio multi channel sound AV FRONT CENTER SUBWOOFER SURROUND amp D D Analog audio MIXED 2CH connection Use the audio cable supplied with the player to connect AUDIO OUT L left and R right jacks of the player to the corresponding input jacks on your audio equipment such as an AV receiver 6000000000 00000000010 AV AV receiver Video connections If your AV receiver features video output jacks connect this uni

Yamaha DVD-S2500 Owner's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents